SERVICE Whirlpool Europe Customer Services Model ADG 6966 IXM Version 8542 966 10750 Page Technical data 2 - 4 Spare part list 5 - 6 Exploded view 7 - 8 Circuit diagram 9 Program diagram 10 Text/Legend 11 - 17 Family VBL - HIGH 6 Sensor 2 Service Manual Dishwasher integratable ADG 6966 IXM ADG 6966 IXM This documentation is only intended for qualified technicians who are aware of the respec- tive safety regulations. Date: 08.06.2004 (Mod. 01) Subject to modification Document-No.: 4812 718 17747
17
Embed
Service Manual - ESpecmonitor.espec.ws/files/854296610750_1_163.pdf · SERVICE Whirlpool Europe Customer Services Model ADG 6966 IXM Version 8542 966 10750 Page Technical data 2 -
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
S E R V I C EWhirlpool Europe
Customer Services
Model ADG 6966 IXM Version 8542 966 10750 Page
Technical data 2 - 4
Spare part list 5 - 6
Exploded view 7 - 8
Circuit diagram 9
Program diagram 10
Text/Legend 11 - 17
Family VBL - HIGH 6Sensor 2
Service ManualDishwasherintegratableADG 6966 IXM
ADG 6966 IXM
This documentation is only intended for qualified technicians who are aware of the respec-tive safety regulations.Date: 08.06.2004 (Mod. 01) Subject to modificationDocument-No.: 4812 718 17747
S E R V I C E26.03.2002 / Page 2 ADG 6966 IXM Whirlpool EuropeDoc. No: 4812 718 17747 8542 966 10750 Customer Service
Thickness min. 16 mmThickness max. 20 mmWidth min. 592 mmWidth max. 595 mmHeight min. 515 mmHeight max. 600 mmWeight max. 5.5 kgMax. stick out over loweredge of appliance door 92 mmHeight of plinth min. 93 mm
Electronic boards
Service boards see spare part listSerial boards see on the boards itselfDUB 4619 724 04851Programing of version and programmed controlboard, see „Service“ and „Data set“ on ratingplate of inner door:CB programmed 461643Data set 461633Basic control board, not programmed see on theboard itself 4619 724 42092
Succession of programs
Programs see program diagramSuccession A1a - A2a - A3a - A5a - A8a - A9a
Datas Energy Label
Reference program A5aEnergy Performance ACleaning Performance ADrying Performance A
Alarms
Refill rinse aidRefill salt
Options
Zone washingDelay function
Program information
Start indicatorPre washMain washDryingEnd
All programs will be locked after start. Changingthe program or finishing the program will bepossible only after pressing the start button forlonger then 1.5 sec. (Break by customer)
A switching off the appliance or unplug theappliance for a while, this will frozen the programstep and later on, the program continuos on thesame position.
Exception: Switching off the appliance or unplugthe appliance during the drying phase, this will leaddirectly to the end of the program.
Water Volume at alternating spray system
Volume at alternating spray system (same levelwhen selected zone washing as in the normalprograms)
Water Volume Level
Regeneration 0.3 l 15 mmBack rinse 3x 1.0 l 60 mmPrewash 3.9 l 120 mmMain wash 3.2 l 118 mmIntermediate rinse 1 3.2 l 118 mmIntermediate rinse 2 3.2 l 118 mmClear rinse 3.2 l 118 mmSafety/ overflow 8.5 l 141 mm
Measuring the level
Remove the coarse sieve, put in a measuringmeter into the sump, measure the hight of thewater level.
Detergent max.
Pre-wash 10 cm3
Main-wash 40 cm3
Rinse aid 135 cm3
6 Dosage steps 1 - 6 ml
Water softener
Saltcontainer 2 kgResin container 900 cm3
Regeneration dosage 300 cm3
S E R V I C EWhirlpool Europe ADG 6966 IXM 26.03.2002 / Page 3Customer Service 8542 966 10750 Doc. No: 4812 718 17747
Technical data
Water pressure
Inlet pressure 0.3 - 10 barSpray pump pressure 0.3 bar
Rotations
Spray pump motor 2800 RPMDrain pump motor 3000 RPMSpray arm lower 30 - 40 RPMSpray arm upper 30 - 40 RPMFan for drying 2500 RPM
Spray arms, turning rhythm at alternating spray
system
Turning starts every time with the upper spray arm
Pre wash Lower arm ~3min, Upper arm ~1minMain wash Lower arm ~3min, Upper arm ~5minIntermediate rinse
Lower arm ~2min, Upper arm ~2minFinal rinse Lower arm ~2min, Upper arm ~2minService Test program
Lower arm ~30sec, Upper arm ~30sec
Remark: When switching of the main switch orinterrupt the mains during the Test Program runs,then the alternating of the spray arms change inthe test program to the rhythm of main wash 5/3min.
Important: To leaf the Test program is possible bymade a break by customer (pushing the startbutton for 1.5 sec.)After finishing the test program (End LED shinesand/or Start LED goes of) must the appliance beswitched off.If this will not be done, then the next normal washwill be made with the frequency of the ServiceTest Program ~30/30sec.
Flow rates/ Inlet volume
Flow meter (at 0.3 bar= quantity 1.1 l/min) 208 lmp/lSpray pump 45 - 65 l/minDrain pump 16 l/minPump height max. 1.1 mInlet valve 4 l/minSpray arm lower ~ 33 l/minSprayarm upper ~ 27 l/minShower top ~ 8 l/minFan for drying:Total 900 l/minPrimary air flow 210 l/minSecondary air flow 780 l/min
Electrical base data
Voltage 220/ 230 VFrequency 50 HzTotal power 2.0 - 2.2 kWFuse 10 A
Motor
Spray pump motor alternating spray system
Voltage 220/ 240 VPower consumption 125 WHI 79 ΩHA 60 ΩCapacitor 4 µ F
Drain pump motor
Voltage 220/ 240 VPower consumption 30 WResistance 146 Ω
Fan for drying
Voltage 220 - 240 VResistance 141 Ω
Heating
1 Element system
Voltage 220/ 230 VPower consumption 1.87/ 2.04 kWResistance 24.5 ΩHeating speed ~ 2.0 ˚C/minTemperature on surface ~ 115 ˚CSafety thermostatself reset(Temperature of water) ~ 85 ˚CFuse 206 ˚C