SERVICE MANUAL US Model - Diagramas dediagramas.diagramasde.com/otros/CDX-S2210X.pdfSERVICE MANUAL US Model CDX-S2210/SW330 Canadian Model CDX-S2210 E Model CDX-S2210S/S2210X East
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
1
Ver. 1.3 2005. 11
Model Name Using Similar Mechanism NEW
CD Drive Mechanism Type MG-611TA-186//K
Optical Pick-up Name KSS1000E
SERVICE MANUAL US ModelCDX-S2210/SW330
Canadian ModelCDX-S2210
E ModelCDX-S2210S/S2210X
East European ModelCDX-S2250EE
CDX-S2210/S2210S/S2210X/S2250EE/SW330
AUDIO POWER SPECIFICATIONS (US Model)POWER OUTPUT AND TOTAL HARMONIC DISTORTION23.2 watts per channel minimum continuous average power into4 ohms, 4 channels driven from 20 Hz to 20 kHz with no morethan 5% total harmonic distortion.
CD player sectionSignal-to-noise ratio 120 dBFrequency response 10 – 20,000 HzWow and flutter Below measurable limit
Antenna terminal External antenna connectorIntermediate frequency 10.7 MHz/450 kHzUsable sensitivity 9 dBfSelectivity 75 dB at 400 kHzSignal-to-noise ratio 67 dB (stereo),
69 dB (mono)Harmonic distortion at 1 kHz
0.5% (stereo),0.3% (mono)
Separation 35 dB at 1 kHzFrequency response 30 – 15,000 Hz
If the optical pick-up block is defective, please replace the wholeoptical pick-up block.Never turn the semi-fixed resistor located at the side of opticalpick-up block.
CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardousradiation exposure.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORIN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LESDIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCESSONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCESSONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUELOU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
Tone controls Low: ±10 dB at 60 Hz (XPLOD)Mid: ±10 dB at 1 kHz (XPLOD)High: ±10 dB at 10 kHz (XPLOD)
Power requirements 12 V DC car battery(negative ground)
Supplied accessories Card remote commander: RM-X151 (CDX-S2210S/SW330only) Parts for installation and connections (1 set)Front panel case (1)
Design and specifications are subject to change withoutnotice.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCKOR BASE UNITThe laser diode in the optical pick-up block may suffer electrostaticbreakdown because of the potential difference generated by thecharged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic breakdown and also usethe procedure in the printed matter which is included in the repairparts.The flexible board is easily damaged and should be handled withcare.
NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused onthe disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, ob-serve from more than 30 cm away from the objective lens.
Notes on Chip Component Replacement• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
TEST DISCSThis set can playback CD-R and CD-ROM discs. The followingtest discs should be used to check the capability:
CD-R test disc TCD-R082LMT (Part No. J-2502-063-1)CD-RW test disc TCD-W082L (Part No. J-2502-063-2)
SERVICE NOTES
• E, East European Model
This label is located on the bottom of the chassis.
optical pick-up
semi-fixed resistor
3
z UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed withthe lead free mark due to their particular size.)
: LEAD FREE MARKUnleaded solder has the following characteristics.• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350°C.Caution: The printed pattern (copper foil) may peel away if theheated tip is applied for too long, so be careful!
• Strong viscosityUnleaded solder is more viscous (sticky, less prone to flow)than ordinary solder so use caution not to let solder bridgesoccur such as on IC pins, etc.
• Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.
CDX-S2210/S2210S/S2210X/S2250EE/SW330
• CD Playback:You can play CD-DA (also containing CD TEXT*1), CD-R/CD-RW (MP3 files also containing Multi Session and ATRAC CD(ATRAC3 and ATRAC3plus format).
Type of discs Label on the disc
CD-DA
MP3
ATRAC CD
*1 A CD TEXT disc is a CD-DA that includes information such asdisc, artist and track name.
EXTENSION CABLE AND SERVICE POSITIONWhen repairing or servicing this set, connect the jig (extension cable)as shown below.
• Connect the MAIN board (CNP301) and the SERVO board (CN2)with the extension cable (Part No. J-2502-076-1).
SERVO BOARDCN2
MAIN BOARDCNP301
J-2502-076-1
4
CDX-S2210/S2210S/S2210X/S2250EE/SW330
TABLE OF CONTENTS
1. GENERALLocation of controls and basic operations (CDX-S2210) ....... 5Location of controls and basic operations (CDX-S2250EE) .. 5Location of controls and basic operations(CDX-S2210S/S2210X) .......................................................... 5Location of controls and basic operations (CDX-SW330) ..... 6Connections (CDX-S2210) ..................................................... 7Connections (CDX-S2210S/S2210X) ..................................... 8Connections (CDX-S2250EE) ................................................ 9Connections (CDX-SW330) .................................................. 10
2. DISASSEMBLY2-1. Sub Panel (LCD) Assy ...................................................... 112-2. CD Mechanism Block ....................................................... 122-3. Main Board ....................................................................... 122-4. Chassis (T) Sub Assy ........................................................ 132-5. Roller Arm Assy ................................................................ 132-6. Chassis (OP) Assy ............................................................. 142-7. Optical Pick-up ................................................................. 142-8. SL Motor Assy (M902) ..................................................... 152-9. LE Motor Assy (M903) ..................................................... 152-10. Servo Board ....................................................................... 16
4. EXPLODED VIEWS4-1. Main Section ..................................................................... 394-2. Front Panel Section ........................................................... 404-3. CD Mechanism Section (1) (MG-611TA-186//K) ............ 414-4. CD Mechanism Section (2) (MG-611TA-186//K) ............ 424-5. CD Mechanism Section (3) (MG-611TA-186//K) ............ 434-6. CD Mechanism Section (4) (MG-611TA-186//K) ............ 44
5. ELECTRICAL PARTS LIST ......................................... 45
5
CDX-S2210/S2210S/S2210X/S2250EE/SW330
Location of controls and basic operations
Main unit
Refer to the pages listed for details.
a Volume +/– buttonTo adjust volume.
b SEL (select) button 4, 7To select items.
c SOURCE buttonTo power on/change the source (Radio/CD).
d MODE button 6To select the radio band (FM/AM).
e Disc slotInsert the disc (label side up), playback starts.
f Display windowg ATT (attenuate) button
To attenuate the sound. To cancel, press again.
h EQ3 (equalizer) button 7To select an equalizer type (XPLOD, VOCAL, CLUB, JAZZ, NEW AGE, ROCK, CUSTOM or OFF).
i Z (eject) buttonTo eject the disc.
j SEEK +/– buttonRadio:To tune in stations automatically (press); find a station manually (press and hold).CD:To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); fast-forward/reverse a track (press and hold).
k (front panel release) button 4
l DSPL (display)/DIM (dimmer) button 4To change display items (press); change the display brightness (press and hold).
m SENS buttonTo improve weak reception: LOCAL/MONO.
n RESET button (located behind the front panel) 4
o Number buttonsRadio:To receive stored stations (press); store stations (press and hold).CD:(1)/(2): GROUP* –/+To skip groups (press); skip groups continuously (press and hold).(3): REP 6(4): SHUF 6
p BTM button 6To start the BTM function (press and hold).
q OFF buttonTo power off/stop the source.
r Receptor for the card remote commander 8
* When an MP3/ATRAC CD is played.
SENS BTM OFFDSPL 1 2 3 4 5 6
SEL
DIM SHUFREP
EQ3ATTSOURCE MODE SEEK
CDX-S2250EE
– +GROUP
qa
1 2 3 4 5 6 7 8 9 0
qs qd qg qh qj qkqf
Location of controls and basic operations
Main unit
Refer to the pages listed for details.
a Volume +/– buttonTo adjust volume.
b SEL (select) button 4, 7To select items.
c SOURCE buttonTo power on/change the source (Radio/CD).
d MODE button 6To select the radio band (FM/AM).
e Disc slotInsert the disc (label side up), playback starts.
f Display windowg ATT (attenuate) button
To attenuate the sound. To cancel, press again.
h EQ3 (equalizer) button 7To select an equalizer type (XPLOD, VOCAL, CLUB, JAZZ, NEW AGE, ROCK, CUSTOM or OFF).
i Z (eject) buttonTo eject the disc.
j SEEK +/– buttonRadio:To tune in stations automatically (press); find a station manually (press and hold).CD:To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); fast-forward/reverse a track (press and hold).
k (front panel release) button 4
l DSPL (display)/DIM (dimmer) button 4, 6To change display items (press); change the display brightness (press and hold).
m SENS buttonTo improve weak reception: LOCAL/MONO.
n RESET button (located behind the front panel) 4
o Number buttonsRadio:To receive stored stations (press); store stations (press and hold).CD:(1)/(2): GROUP* –/+To skip groups (press); skip groups continuously (press and hold).(3): REP 6(4): SHUF 6
p BTM button 6To start the BTM function (press and hold).
q OFF buttonTo power off/stop the source.
r Receptor for the card remote commander 8
* When an MP3/ATRAC CD is played.
SENS BTM OFFDSPL 1 2 3 4 5 6
SEL
DIM SHUFREP
EQ3ATTSOURCE MODE SEEK
CDX-S2210
– +GROUP
qa
1 2 3 4 5 6 7 8 9 0
qs qd qg qh qj qkqf
Location of controls and basic operations
Main unit
Card remote commander RM-X151(CDX-S2210S only)
)
SENS BTM OFFDSPL 1 2 3 4 5 6
SEL
DIM SHUFREP
EQ3ATTSOURCE MODE SEEK
CDX-S2210XCDX-S2210SCDX-S2210C
– +GROUP
qa
1 2 3 4 5 6 7 8 9 0
qs qd qg qh qj qkqf ql
SENS BTM OFFDSPL 1 2 3 4 5 6
SEL
DIM SHUFREP
EQ3ATTSOURCE MODE SEEK
CDX-S2210XCDX-S2210SCDX-S2210C
– +GROUP
qa
1 2 3 4 5 6 7 8 9 0
qs qd qg qh qj qkqf ql
OFF
DSPL SCRL
SELSOURCE MODE
1 32
4 65
ATT
VOL+
–
+
–
7
qs
qk
342
wd
w;
wa
wf
ws
Refer to the pages listed for details. The corresponding buttons on the card remote commander control the same functions as those on the unit.
a Volume +/– buttonTo adjust volume.
b SEL (select) button 4, 9To select items.
c SOURCE buttonTo power on/change the source (Radio/CD).
d MODE button 8To select the radio band (FM/AM).
e Disc slotInsert the disc (label side up), playback starts.
f Display windowg ATT (attenuate) button
To attenuate the sound. To cancel, press again.
h EQ3 (equalizer) button 9To select an equalizer type (XPLOD, VOCAL, CLUB, JAZZ, NEW AGE, ROCK, CUSTOM or OFF).
i Z (eject) buttonTo eject the disc.
j SEEK +/– buttonRadio:To tune in stations automatically (press); find a station manually (press and hold).CD:To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); fast-forward/reverse a track (press and hold).
k (front panel release) button 4l DSPL (display)/DIM (dimmer) button
4, 8To change display items (press); change the display brightness (press and hold).
m SENS buttonTo improve weak reception: LOCAL/MONO.
n RESET button (located behind the front panel) 4
o Frequency select switch (located on the bottom of the unit)See “Frequency select switch” in the supplied installation/connections manual.
p Number buttonsRadio:To receive stored stations (press); store stations (press and hold).CD:(1)/(2): GROUP* –/+To skip groups (press); skip groups continuously (press and hold).(3): REP 8(4): SHUF 8
q BTM button 8To start the BTM function (press and hold).
r OFF buttonTo power off/stop the source.
s Receptor for the card remote commander 10
The following buttons on the card remote commander have also different buttons/functions from the unit.
t < (.)/, (>) buttonsTo control radio/CD, the same as (SEEK) +/– on the unit. (For details of other operations, see “With the card remote commander” on each pages.)
u VOL +/– buttonTo adjust volume.
v M (+)/m (–) buttonsTo control CD, the same as (1)/(2) –/+ on the unit. (For details of other operations, see “With the card remote commander” on each pages.)
w SCRL buttonTo scroll the display item.
x Number buttonsTo receive stored stations (press); store stations (press and hold).
* When an MP3/ATRAC CD is played.
NoteIf the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first.
TipFor details on how to replace the battery, see “Replacing the lithium battery of the card remote commander” on page 13.
SECTION 1GENERAL This section is extracted
from instruction manual.
(CDX-S2210) (CDX-S2250EE)
(CDX-S2210S/S2210X)
6
CDX-S2210/S2210S/S2210X/S2250EE/SW330
Location of controls and basic operations
Main unit
Card remote commander RM-X151
SENS BTM OFFDSPL 1 2 3 4 5 6
SEL
DIM SHUFREP
EQ3ATTSOURCE MODE SEEK
CDX-SW330
– +GROUP
qa
1 2 3 4 5 6 7 8 9 0
qs qd qg qh qjqf qk
OFF
DSPL SCRL
SELSOURCE MODE
1 32
4 65
ATT
VOL+
–
+
–
7
qs
qj
342
ws
ql
w;
wd
wa
Refer to the pages listed for details. The corresponding buttons on the card remote commander control the same functions as those on the unit.
a Volume +/– buttonTo adjust volume.
b SEL (select) button 4, 9, 9, 9To select items.
c SOURCE buttonTo power on/change the source (Radio/CD).
d MODE button 8To select the radio band (FM/AM).
e Disc slotInsert the disc (label side up), playback starts.
f Display windowg ATT (attenuate) button
To attenuate the sound. To cancel, press again.
h EQ3 (equalizer) button 9To select an equalizer type (XPLOD, VOCAL, CLUB, JAZZ, NEW AGE, ROCK, CUSTOM or OFF).
i Z (eject) buttonTo eject the disc.
j SEEK +/– buttonRadio:To tune in stations automatically (press); find a station manually (press and hold).CD:To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); fast-forward/reverse a track (press and hold).
k (front panel release) button 4l DSPL (display)/DIM (dimmer) button
4, 8To change display items (press); change the display brightness (press and hold).
m SENS buttonTo improve weak reception: LOCAL/MONO.
n RESET button (located behind the front panel) 4
o Number buttonsRadio:To receive stored stations (press); store stations (press and hold).CD:(1)/(2): GROUP* –/+To skip groups (press); skip groups continuously (press and hold).(3): REP 8(4): SHUF 8
p BTM button 8To start the BTM function (press and hold).
q OFF buttonTo power off/stop the source.
r Receptor for the card remote commander
The following buttons on the card remote commander have also different buttons/functions from the unit.
s < (.)/, (>) buttonsTo control radio/CD, the same as (SEEK) +/– on the unit. (For details of other operations, see “With the card remote commander” on each pages.)
t VOL +/– buttonTo adjust volume.
u M (+)/m (–) buttonsTo control CD, the same as (1)/(2) –/+ on the unit. (For details of other operations, see “With the card remote commander” on each pages.)
v SCRL buttonTo scroll the display item.
w Number buttonsTo receive stored stations (press); store stations (press and hold).
* When an MP3/ATRAC CD is played.
NoteIf the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first.
TipFor details on how to replace the battery, see “Replacing the lithium battery of the card remote commander” on page 11.
(CDX-SW330)
7
CDX-S2210/S2210S/S2210X/S2250EE/SW330
Connections (CDX-S2210)
BUSAUDIO
IN
L
R
AUDIOOUT
L
R
AUDIO OUT REAR*2
2
4
5
1
3
Schéma de raccordement (3)1 À un point métallique de la voiture
Branchez d’abord le câble de mise à la masse noir et, ensuite, les câbles d’entrée d’alimentation jaune et rouge.
2 Vers le câble de commande d’antenne électrique ou le câble d’alimentation de l’amplifi cateur d’antenneRemarques• Il n’est pas nécessaire de raccorder ce câble s’il n'y a pas
d’antenne électrique ni d’amplifi cateur d’antenne, ou avec une antenne télescopique manuelle.
• Si votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, voir « Remarques sur les câbles de commande et d’alimentation ».
3 Au niveau de AMP REMOTE IN de l’amplifi cateur de puissance en optionCe raccordement s’applique uniquement aux amplifi cateurs. Le branchement de tout autre système risque d’endommager l’appareil.
4 À la borne +12 V qui est alimentée quand la clé de contact est sur la position accessoiresRemarques• S’il n’y a pas de position accessoires, raccordez la borne
d’alimentation (batterie) +12 V qui est alimentée en permanence. Raccordez d’abord le câble de mise à la masse noir à un point métallique du véhicule.
• Si votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, voir « Remarques sur les câbles de commande et d’alimentation ».
5 À la borne +12 V qui est alimentée en permanenceRaccordez d’abord le câble de mise à la masse noir à un point métallique du véhicule.
Connection diagram (3)1 To a metal surface of the car
First connect the black ground lead, then connect the yellow and red power input leads.
2 To the power antenna control lead or power supply lead of antenna booster amplifi erNotes• It is not necessary to connect this lead if there is no power
antenna or antenna booster, or with a manually-operated telescopic antenna.
• When your car has a built-in FM/AM antenna in the rear/side glass, see “Notes on the control and power supply leads.”
3 To AMP REMOTE IN of an optional power amplifi erThis connection is only for amplifi ers. Connecting any other system may damage the unit.
4 To the +12 V power terminal which is energized in the accessory position of the ignition key switchNotes• If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times. Be sure to connect the black ground lead to a metal
surface of the car fi rst.• When your car has a built-in FM/AM antenna in the rear/
side glass, see “Notes on the control and power supply leads.”
5 To the +12 V power terminal which is energized at all timesBe sure to connect the black ground lead to a metal surface of the car fi rst.
AMP REM
Max. supply current 0.3 ACourant max. fourni 0,3 A
Fuse (10 A)Fusible (10 A)
Blue/white stripedRayé bleu/blanc
from car antenna à partir de l’antenne de la voiture
ANT REM
2
*1
RedRouge
YellowJaune
BlackNoir
BlueBleu
WhiteBlanc
GreenVert
PurpleMauve
White/black stripedRayé blanc/noir
Gray/black stripedRayé gris/noir
Green/black stripedRayé vert/noir
GrayGris
LeftGauche
RightDroit
LeftGauche
RightDroit
Max. supply current 0.1 ACourant max. fourni 0,1 A
*1 RCA pin cord (not supplied)*2 AUDIO OUT can be switched to SUB
or REAR. For details, see the supplied
operating instructions.
*1 Cordon à broche RCA (non fourni)*2 AUDIO OUT peut être commuté sur
SUB ou REAR. Pour obtenir plus de détails, reportez-
vous au mode d’emploi fourni.
Purple/black stripedRayé mauve/noir
Remarques sur les câbles de commande et d’alimentation• Le câble de commande d’antenne électrique (bleu) fournit une
alimentation de + 12 V CC lorsque vous mettez la radio sous tension.
• Lorsque votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, raccordez le câble de commande d’antenne (bleu) ou l’entrée d’alimentation des accessoires (rouge) à la borne d’alimentation de l’amplifi cateur d’antenne existant. Pour plus de détails, consultez votre détaillant.
• Une antenne électrique sans boîtier de relais ne peut pas être utilisée avec cet appareil.
Raccordement pour la conservation de la mémoireLorsque le câble d’entrée d’alimentation jaune est raccordé, le circuit de la mémoire est alimenté en permanence même si la clé de contact est sur la position d’arrêt.
Remarques sur le raccordement des haut-parleurs• Avant de raccorder les haut-parleurs, mettez l’appareil hors
tension.• Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms
avec une capacité électrique adéquate pour éviter de les endommager.
• Ne raccordez pas les bornes du système de haut-parleurs au châssis de la voiture et ne raccordez pas les bornes des haut-parleurs droit à celles du haut-parleur gauche.
• Ne raccordez pas le câble de mise à la masse de cet appareil à la borne négative (–) du haut-parleur.
• N’essayez pas de raccorder les haut-parleurs en parallèle.• Raccordez uniquement des haut-parleurs passifs. Le
raccordement de haut-parleurs actifs (avec amplifi cateurs intégrés) aux bornes des haut-parleurs peut endommager l’appareil.
• Pour éviter tout dysfonctionnement, n’utilisez pas les câbles des haut-parleurs intégrés installés dans votre voiture si l’appareil partage un câble négatif commun (–) pour les haut-parleurs droit et gauche.
• Ne raccordez pas entre eux les cordons des haut-parleurs de l’appareil.
Remarque sur le raccordementSi les haut-parleurs et l’amplifi cateur ne sont pas raccordés correctement, le message « FAILURE » s’affi che. Dans ce cas, assurez-vous que les haut-parleurs et l’amplifi cateur sont bien raccordés.
Notes on the control and power supply leads• The power antenna control lead (blue) supplies +12 V DC
when you turn on the tuner.• When your car has built-in FM/AM antenna in the rear/side
glass, connect the power antenna control lead (blue) or the accessory power input lead (red) to the power terminal of the existing antenna booster. For details, consult your dealer.
• A power antenna without a relay box cannot be used with this unit.
Memory hold connectionWhen the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off.
Notes on speaker connection• Before connecting the speakers, turn the unit off.• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the left speaker.
• Do not connect the ground lead of this unit to the negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.• Connect only passive speakers. Connecting active speakers
(with built-in amplifi ers) to the speaker terminals may damage the unit.
• To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connectionIf speaker and amplifi er are not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker and amplifi er are connected correctly.
8
CDX-S2210/S2210S/S2210X/S2250EE/SW330
Connections (CDX-S2210S/S2210X)
9
CDX-S2210/S2210S/S2210X/S2250EE/SW330
Connections (CDX-S2250EE)
10
CDX-S2210/S2210S/S2210X/S2250EE/SW330
Connections (CDX-SW330)
Diagrama de conexión (3)1 A una superfi cie metálica del automóvil
Conecte primero el cable de conexión a masa negro, y después los cables con rayas naranjas y blancas, amarillo, y rojo de entrada de alimentación.
2 Al cable de control de la antena motorizada o al cable de fuente de alimentación del amplifi cador de señal de la antenaNotas• Si no se dispone de antena motorizada ni de amplifi cador
de antena, o se utiliza una antena telescópica accionada manualmente, no será necesario conectar este cable.
• Si el automóvil incorpora una antena de FM/AM en el cristal trasero o lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”.
3 A AMP REMOTE IN de un amplifi cador de potencia opcionalEsta conexión es sólo para amplifi cadores. La conexión de cualquier otro sistema puede dañar la unidad.
4 Al terminal de alimentación de +12 V que recibe energía en la posición de accesorio del interruptor de la llave de encendidoNotas• Si no hay posición de accesorio, conéctelo al terminal de
alimentación (batería) de +12 V que recibe energía sin interrupción.
Asegúrese de conectar primero el cable de conexión a masa negro a una superfi cie metálica del automóvil.
• Si el automóvil incorpora una antena de FM/AM en el cristal trasero o lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”.
5 Al terminal de alimentación de +12 V que recibe energía sin interrupciónAsegúrese de conectar primero el cable de conexión a masa negro a una superfi cie metálica del automóvil.
Notas sobre los cables de control y de fuente de alimentación• El cable de control de la antena motorizada (azul) suministrará
cc de + 12 V cuando conecte la alimentación del sintonizador.• Si el automóvil dispone de una antena de FM/AM incorporada
en el cristal trasero o lateral, conecte el cable de control de antena motorizada (azul) o el cable de entrada de alimentación auxiliar (rojo) al terminal de alimentación del amplifi cador de antena existente. Para obtener más información, consulte a su distribuidor.
• Con esta unidad no es posible utilizar una antena motorizada sin caja de relé.
Conexión para protección de la memoriaSi conecta el cable de entrada de alimentación amarillo, el circuito de la memoria recibirá siempre alimentación, aunque apague la llave de encendido.
Notas sobre la conexión de los altavoces• Antes de conectar los altavoces, desconecte la alimentación
de la unidad.• Utilice altavoces con una impedancia de 4 a 8 Ω con la
capacidad de potencia adecuada para evitar que se dañen.• No conecte los terminales de altavoz al chasis del automóvil,
ni conecte los terminales del altavoz derecho con los del izquierdo.
• No conecte el cable de conexión a masa de esta unidad al terminal negativo (–) del altavoz.
• No intente conectar los altavoces en paralelo.• Conecte solamente altavoces pasivos. Si conecta altavoces
activos (con amplifi cadores incorporados) a los terminales de altavoz, puede dañar la unidad.
• Para evitar fallos de funcionamiento, no utilice los cables de altavoz incorporados instalados en el automóvil si su unidad comparte un cable negativo común (–) para los altavoces derecho e izquierdo.
• No conecte los cables de altavoz de la unidad entre sí.
Nota sobre la conexiónSi el altavoz y el amplifi cador no están conectados correctamente, aparecerá “FAILURE” en la pantalla. Si es así, compruebe la conexión de ambos dispositivos.
*1 RCA pin cord (not supplied)*2 AUDIO OUT can be switched to SUB or
REAR.For details, see the supplied operating instructions.
*1 Cordon à broche RCA (non fourni)*2 AUDIO OUT peut être commuté sur SUB
ou REAR. Pour obtenir plus de détails, reportez-vous
au mode d’emploi fourni.
*1 Cable con terminales RCA (no suministrado)
*2 AUDIO OUT (Salida de audio) puede cambiarse a SUB (Secundaria) o REAR (Posterior).Para obtener información, consulte el manual de instrucciones suministrado.BUS
AUDIOIN
L
R
L
R
AUDIO OUT REAR*2
2
4
5
1
3
2
AMP REM
Max. supply current 0.3 ACourant max. fourni 0,3 ACorriente máx. de alimentación de 0,3 A
Fuse (10 A)Fusible (10 A)Fusible (10 A)
Blue/white stripedRayé bleu/blancCon rayas azules y blancas
from car antennaà partir de l’antenne de la voituredesde la antena del automóvil
*1
RedRougeRojo
YellowJauneAmarillo
WhiteBlancBlanco
GreenVertVerde
PurpleMauveMorado
White/black stripedRayé blanc/noirCon rayas blancas y negras
Gray/black stripedRayé gris/noirCon rayas grises y negras
Green/black stripedRayé vert/noirCon rayas verdes y negras
GrayGrisGris
LeftGaucheIzquierdo
RightDroitDerecho
LeftGaucheIzquierdo
RightDroitDerecho
ANT REM
BlackNoirNegro
BlueBleuAzul
Max. supply current 0.1 ACourant max. fourni 0,1 A
Corriente máx. de alimentación de 0,1 A
Purple/black stripedRayé mauve/noirCon rayas moradas y negras
Schéma de raccordement (3)1 À un point métallique de la voiture
Branchez d’abord le câble de mise à la masse noir et, ensuite, les câbles d’entrée d’alimentation jaune et rouge.
2 Vers le câble de commande d’antenne électrique ou le câble d’alimentation de l’amplifi cateur d’antenneRemarques• Il n’est pas nécessaire de raccorder ce câble s’il n'y a pas
d’antenne électrique ni d’amplifi cateur d’antenne, ou avec une antenne télescopique manuelle.
• Si votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, voir « Remarques sur les câbles de commande et d’alimentation ».
3 Au niveau de AMP REMOTE IN de l’amplifi cateur de puissance en optionCe raccordement s’applique uniquement aux amplifi cateurs. Le branchement de tout autre système risque d’endommager l’appareil.
4 À la borne +12 V qui est alimentée quand la clé de contact est sur la position accessoiresRemarques• S’il n’y a pas de position accessoires, raccordez la borne
d’alimentation (batterie) +12 V qui est alimentée en permanence. Raccordez d’abord le câble de mise à la masse noir à un point métallique du véhicule.
• Si votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, voir « Remarques sur les câbles de commande et d’alimentation ».
5 À la borne +12 V qui est alimentée en permanenceRaccordez d’abord le câble de mise à la masse noir à un point métallique du véhicule.
Remarques sur les câbles de commande et d’alimentation• Le câble de commande d’antenne électrique (bleu) fournit une
alimentation de + 12 V CC lorsque vous mettez la radio sous tension.
• Lorsque votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, raccordez le câble de commande d’antenne (bleu) ou l’entrée d’alimentation des accessoires (rouge) à la borne d’alimentation de l’amplifi cateur d’antenne existant. Pour plus de détails, consultez votre détaillant.
• Une antenne électrique sans boîtier de relais ne peut pas être utilisée avec cet appareil.
Raccordement pour la conservation de la mémoireLorsque le câble d’entrée d’alimentation jaune est raccordé, le circuit de la mémoire est alimenté en permanence même si la clé de contact est sur la position d’arrêt.
Remarques sur le raccordement des haut-parleurs• Avant de raccorder les haut-parleurs, mettez l’appareil hors
tension.• Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms
avec une capacité électrique adéquate pour éviter de les endommager.
• Ne raccordez pas les bornes du système de haut-parleurs au châssis de la voiture et ne raccordez pas les bornes des haut-parleurs droit à celles du haut-parleur gauche.
• Ne raccordez pas le câble de mise à la masse de cet appareil à la borne négative (–) du haut-parleur.
• N’essayez pas de raccorder les haut-parleurs en parallèle.• Raccordez uniquement des haut-parleurs passifs. Le
raccordement de haut-parleurs actifs (avec amplifi cateurs intégrés) aux bornes des haut-parleurs peut endommager l’appareil.
• Pour éviter tout dysfonctionnement, n’utilisez pas les câbles des haut-parleurs intégrés installés dans votre voiture si l’appareil partage un câble négatif commun (–) pour les haut-parleurs droit et gauche.
• Ne raccordez pas entre eux les cordons des haut-parleurs de l’appareil.
Remarque sur le raccordementSi les haut-parleurs et l’amplifi cateur ne sont pas raccordés correctement, le message « FAILURE » s’affi che. Dans ce cas, assurez-vous que les haut-parleurs et l’amplifi cateur sont bien raccordés.
AUDIOOUT
Connection diagram (3)1 To a metal surface of the car
First connect the black ground lead, then connect the yellow and red power input leads.
2 To the power antenna control lead or power supply lead of antenna booster amplifi erNotes• It is not necessary to connect this lead if there is no power
antenna or antenna booster, or with a manually-operated telescopic antenna.
• When your car has a built-in FM/AM antenna in the rear/side glass, see “Notes on the control and power supply leads.”
3 To AMP REMOTE IN of an optional power amplifi erThis connection is only for amplifi ers. Connecting any other system may damage the unit.
4 To the +12 V power terminal which is energized in the accessory position of the ignition key switchNotes• If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times. Be sure to connect the black ground lead to a metal
surface of the car fi rst.• When your car has a built-in FM/AM antenna in the rear/
side glass, see “Notes on the control and power supply leads.”
5 To the +12 V power terminal which is energized at all timesBe sure to connect the black ground lead to a metal surface of the car fi rst.
Notes on the control and power supply leads• The power antenna control lead (blue) supplies +12 V DC
when you turn on the tuner.• When your car has built-in FM/AM antenna in the rear/side
glass, connect the power antenna control lead (blue) or the accessory power input lead (red) to the power terminal of the existing antenna booster. For details, consult your dealer.
• A power antenna without a relay box cannot be used with this unit.
Memory hold connectionWhen the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off.
Notes on speaker connection• Before connecting the speakers, turn the unit off.• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the left speaker.
• Do not connect the ground lead of this unit to the negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.• Connect only passive speakers. Connecting active speakers
(with built-in amplifi ers) to the speaker terminals may damage the unit.
• To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connectionIf speaker and amplifi er are not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker and amplifi er are connected correctly.
11
CDX-S2210/S2210S/S2210X/S2250EE/SW330
SECTION 2DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
Note : Follow the disassembly procedure in the numerical order given.
2-1. SUB PANEL (LCD) ASSY
2-1. SUB PANEL (LCD) ASSY (Page 11)
2-2. CD MECHANISM BLOCK(Page 12)
SET
2-3. MAIN BOARD(Page 12)
2-4. CHASSIS (T) SUB ASSY(Page 13)
2-5. ROLLER ARM ASSY(Page 13)
2-6. CHASSIS (OP) ASSY(Page 14)
2-8. SL MOTOR ASSY (M902)(Page 15)
2-10. SERVO BOARD(Page 16)
2-7. OPTICAL PICK-UP(Page 14)
2-9. LE MOTOR ASSY (M903)(Page 15)
2 two claws
3 two claws
4 sub panel (LCD) assy
1 two screws (+PTT 2.6 x 6)
12
CDX-S2210/S2210S/S2210X/S2250EE/SW330
2-2. CD MECHANISM BLOCK
2-3. MAIN BOARD
7 bracket (CD)
5 CD mechanism block
4 CNP301
3
1 screw (+PTT 2.6 x 6)
2 screw (+PTT 2.6 x 6)
6 two screws (+PTT 2.6 x 4)
1 three screws (+BTT)
3 MAIN board
4 insulating sheet
2 two screws (+PTT 2.6 x 8)
13
CDX-S2210/S2210S/S2210X/S2250EE/SW330
2-4. CHASSIS (T) SUB ASSY
2-5. ROLLER ARM ASSY
3 washer (1.1-2.5)
4 gear (RA1)
5 roller arm assy
1 spring (RAL)
2 spring (RAR)
5 SENSOR board
6 chassis (T) sub assy
4 claw
3 claw
1 two screws (+P 1.7 x 2.2)
2 two screws (+P 1.7 x 2.2)
14
CDX-S2210/S2210S/S2210X/S2250EE/SW330
2-6. CHASSIS (OP) ASSY
2-7. OPTICAL PICK-UP
4 washer
0 coil spring (damper)
9 two coil springs (damper)
qa chassis (OP) assy
5 gear (LE1)
1 CN2 (16P)
lever (D)
slider (R)
6
7
8
2 Remove the six solderings.
3 tension coil spring (KF60)
1 tension coil spring (CHKG)
2 chucking arm sub assy
3 screw (+B 1.4 x 5)
4 rack (SL)
5 claw
6 main shaft
7 optical pick-up
15
CDX-S2210/S2210S/S2210X/S2250EE/SW330
2-9. LE MOTOR ASSY (M903)
2-8. SL MOTOR ASSY (M902)
1 screw (+P 1.4 x 1.8)
2 SL motor assy (M902)
2 washer
4
qd
3 gear (LE1)
7 leaf spring (LE)
5
lever (D)
bracket (LEM-N)
slider (R)
6 screw (+P 1.7 x 2.2)
8 screw (+M 1.7 x 2.5)
qa screw (+M 1.7 x 2.5)qf two toothed lock screws
(+M 1.4 )
qs screw (+M 1.7 x 2.5)
9 bearing (LEB-N)
0 gear (LE) assy
qg LE motor assy (M903)
1 Remove the soldering.
16
CDX-S2210/S2210S/S2210X/S2250EE/SW330
2-10. SERVO BOARD
3 CN2 (16P)
5 claw
6 SERVO board
4 toothed lock screw (M 1.7)
1 Remove the eight solderings.
2 Remove the three solderings.
17 17
CDX-S2210/S2210S/S2210X/S2250EE/SW330
CDX-S2210/S2210S/S2210X/S2250EE/SW330
3-1. BLOCK DIAGRAM – CD SECTION –
SECTION 3DIAGRAMS
87RFO
RF AMP,DIGITAL SERVO,DIGITAL SIGNAL PROCESSOR
IC2
79RFEQO
3RFRP
6TEI
77 RFI78 RFRPI
1 RFZI
7 TEZI
9 F0O
PD1
PD2
E
F
I-V A
MP
PD LD
DETECTOR
85 AGCI86 RFDCI
94
96
95
97
99
98
TNI
FPI1
FNI1
FPI2
FNI2
TPI
91 LDO 92MDI
(FOCUS)
(TRACKING)
2-AXIS DEVICE
OPTICALPICK-UP BLOCK
(KSS1000E)
• Signal Path: CD PLAY
LASER DIODE
M
M
M
18
17
VO3–
VO3+
14
13
VO1+
VO1–
12
11 VO2–
VO2+
10
9
VOL+
VOL–FWD
REV
1
28
OPIN4– 26
OPOUT4 25
10 TROOPIN3– 23
46 IO0(/HSO)OPOUT3 22
12 FMOOPOUT1 4
13 DMOOPIN2 7
47 IO1(/UHSO)MUTE 21
16
15
VO4–
VO4+
M903(LOADING)
M901(SPINDLE)
M902(SLED)
FOCUS/TRACKING COIL DRIVE,SLED/SPINDLE/LOADING
MOTOR DRIVEIC1
56MUTE53REQ43STBY18ZDET42/RST41/CCE40BUCK39BUS3
CD-L MAIN SECTIONA30LO
27RO R-CH
27 DEC SSTBY15 CD ZDET14 CD XRST13 CD XCCE
53 MEC_SELFSW
45 MEC_INSW
42 MEC_LIMIT
12 CD BUCK11 CD BUS3
38BUS2 10 CD BUS237BUS1 8 CD BUS136BUS0 7 CD BUS014SBSY 52 CD SBSY
81 X1
80 X0
MEC LOAD43
MEC EJECT44
CDSYSTEM CONTROL
IC3
+1.5V REGIC6
SYSTEM CONTROLIC501 (1/3)
37 DEC XMUTE30 DEC INT
SW2(SELF)
46 MEC_DSWSW1(DOWN)
SW3(DISC IN)
SW4(LIMIT)
56UNISI25RXD57UNISO
58UNICKI50BUS ON51BU IN
75RSTX
61EJECT OK
67MECON CHK
11.5V ON
63MECON64CDON66ZMUTE
60A ATT
26TXD
PD1
E
F
LD
MON OUT
FCS+
FCS–
TRK+
TRK–
PD2
AUTOMATICPOWER
CONTROLQ1
+1.5V ON/OFFSWITCH
Q2,3
• R-ch is omitted due to same as L-ch.
24
23X2
16.934MHzX1
12MHz
XI
XO
DISPLAY SECTIONC
MAIN SECTIONB
EJECT OK SW
UNI SI
UNI SO
ATT
UNI CLKBUS ONB/U CHECK
SYS RST
89
CD ON
VOUT
98CDM ON99
Z MUTE
MECHA+6V
93
68CDON CHK
15 VDD3CE
BU+3.3V
+1.5V
+1.5V
BU+3.3V
(Page 18)
(Page 18)
(Page 19)
1818
CDX-S2210/S2210S/S2210X/S2250EE/SW330
CDX-S2210/S2210S/S2210X/S2250EE/SW330
3-2. BLOCK DIAGRAM – MAIN SECTION –
1 ANT 7 TU LCH
ELECTRONIC VOLUMEIC401
J1(ANTENNA)
TU1(TUNER UNIT)
POWER AMP, POWER SUPPLY
IC750
SYSTEM CONTROLIC501 (2/3)
CN601
6 TU RCH
R-CH (FRONT)R-CH (REAR)
BATT
9 CD LCH8 CD RCH
R-CH
43
10VCC11TU VDD15E2P VDD
13TU-SCL14TU-SDA
6S-METER7TU MUTE
16E2P SCL17E2P SDA
39 VSM
AUDIO+8.3VTU+5VBU+3.3V
12 TU ATT
25 EEP CKO24 EEP SIO
L-CHR-CH
CD-L
R-CH 1718
OUT SUB-LOUT SUB-R
R-CH
L
R
53
OUT FL+OUT FL-
97
OUT RL+OUT RL-
2927
AMP-REM
R-CH
ANT-REM
BATT
3037
AUDIO8.3VB.UP+B
3133
SERVO3.3VMECHA6V
34PANEL+B
TU+5V
BATT
2524
OUT FROUT RR
29MUTE
2 SDA
AUDIO+8.3VBU+3.3VSERVO+3.3VMECHA+6VPANEL+B
4 SCL
SDASCL
16 BEEP22 STB25 DIAG
AUDIO+8.3V
35 VP
15
7
10
12
11
16
19
2
4
3
56
3031
SCLSDA
SCLSDA
SCLSDA
SCLSDA
33I2C CKO34I2C SIO
9VOL ATT
86ATT5BEEP26AMP STB8DIAG
54BU IN
73
UNI SI58UNI SO59UNI SCK60BUS ON87
UNI SIUNI SOUNI CLKBUS ONB/U CHECK
ATT
TEST IN
12 IN FL FL+FL-
RL+RL-
FR+FR-RR+RR-
AMP-REMANT-REM
ACC
TEST
23OUT FL
11 IN RL22OUT RL
MUTEQ441
MUTEQ481
AUDIO OUTJ330
MUTE DRIVEQ478,479
BATT
72
74
ACC IN
TEL ATT
BATTERY CHECKQ580-582
ACC CHECKQ631
+5V REGQ1
MUTEQ461
13TEL-MUTE
D479
D571
D580,581
FU601
CD SECTION A
CD SECTION B
TEL MUTEQ651
• Signal Path• R-CH is omitted due to same as L-CH.
• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRINGBOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note is printedin each block.)
For schematic diagrams.Note:• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolyticsand tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.• f : internal component.• C : panel designation.
For printed wiring boards.Note:• X : parts extracted from the component side.• Y : parts extracted from the conductor side.• a : Through hole.• : Pattern from the side which enables seeing.(The other layers' patterns are not indicated.)
• A : B+ Line.• B : B– Line.• H : adjustment for repair .• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.• CD mechanism section (1/2), (2/2) no mark : CD PLAY• Main (1/4), (2/4), (3/4), (4/4) and Display sections no mark : FM
( ) : AM< > : CD PLAY
∗ : Impossible to measure• Voltages are taken with a VOM (Input impedance 10 M Ω).
Voltage variations may be noted due to normal produc-tion tolerances.
• Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal produc-tion tolerances.
• Circled numbers refer to waveforms.• Signal path.
J : CD PLAYF : FMf : AM
Caution:Pattern face side: Parts on the pattern face side seen from the(Side B) pattern face are indicated.Parts face side: Parts on the parts face side seen from the(Side A) parts face are indicated.
Note:The components identi-fied by mark 0 or dottedline with mark 0 are criti-cal for safety.Replace only with partnumber specified.
Note:Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepiéce portant le numérospécifié.
Q
C
These are omitted
EB
EThese are omitted
CB
CThese are omitted
BE
1 IC501 i; (XIN)
1.4Vp-p
32.678kHz
1.2Vp-p
18.432MHz
2 IC501 id (OSCOUT)
1 IC2 4 (FEI)
Approx.1Vp-p
0 V
0.6 Vp-p
16.9344 MHz
Approx. 100 mVp-p
50 mV/DIV, 5 msec/DIV 0.5 V/DIV, 0.5 µsec/DIV
2 IC2 6 (TEI)
200 mV/DIV, 5 msec/DIV
6 IC2 oh (FPI2),
0.5 V/DIV, 0.5 µsec/DIV
Approx. 400 mVp-p
3 IC2 wd (XI)
0.2 V/DIV, 0.2 µsec/DIV
7 IC3 ia (X1)
0.5 V/DIV, 0.2 µsec/DIV
1.1 Vp-p
12 MHz
4 IC2 uj (RFI)
0.5 V/DIV, 0.5 µsec/DIV
5 IC2 of (FNI2),og (FNI1)
1.5 Vp-p
oj (FPI1)
1.5 Vp-p0 V
Ver. 1.3
NOTE FOR REPLACEMENT OF THE IC501IC501 on the main board has two types of IC models: MB90487 and MB90F488B.The service part is the model MB90487 only.Check the model number printed on the IC when replacing IC501.If MB90F488 is printed on the IC, mount the capacitor C551 additionally.
JAPANF
MB90487AMB90F488B
company emblem
IC501 C351
MB90487A 0.001µF
MB90F488B NO MOUNT
21 21
CDX-S2210/S2210S/S2210X/S2250EE/SW330
CDX-S2210/S2210S/S2210X/S2250EE/SW330
3-4. PRINTED WIRING BOARDS – SERVO BOARD – • See page 19 for Circuit Boards Location. : Uses unleaded solder.
1
A
B
C
D
E
F
G
H
2 3 4 5 6 7 8 9 10 11 12 13 14
(KSS1000E)
SW3
SW2
MAIN BOARD CNP301
TP24
TP40
TP17
TP14
TP18
TP37
TP38
TP39
TP30
FMA4
FMA6
FMA3
TP48
TP49TP51TP53
FMA5C37
C9
C38
C39C40C4
1
C43
C48
C67
C72
FB3
R132
R6
R7
R48
R50
R16
R17
R40
R41
R8
R25 R26
R84
R86
R13
1
R122
Q1
IC6
SW1(DOWN)
C106
R12
0
C65
C64
C19R
123
C20
C61
Q3
FB4
C29
C22
R65
C32
C51
C35
C45
C62
R11
R9
C57
R10
IC3
R12
FB2
C6
R11
2
R58
R42
R113
R43
R47
R54R
56R
57R
66
R68
R69
R70
R73 R100
R10
1R13
R21
R71
Q2
C7
C101
C102
C80
C103
IC1
TP4
TP3
TP5
TP33
TP34
TP35TP
36
TP41
TP42
TP47
TP46
TP25
TP26TP27
TP21
TP22
TP68
TP93
TP15
TP64
FMB3
FMB4
TP11
TP86
TP87
TP10
TP1
TP6
TP7
TP8
TP9
TP12
TP13
TP16
TP20
TP32TP
31
TP66
TP67
TP74
TP75TP76
TP77
TP78
TP79TP80TP81
TP82
TP83
TP84
TP85
TP90
TP89
TP88
TP91
TP92
TP95
TP97TP98
TP99
TP2
TP63
TP44
TP43
TP65
TP62
FMB5
TP101
TP23
TP29
CN1
R4
R24
R5
CN2
R61
C5
R49
R51
R45
R46
R2
R3
X1
X1
IC2
R121
C10
C4
R11
9
C18
C47
C34
R11
8
C17
C23
C42
C16
C60
R125
C36
R62
R117
C21
R116
X2
C24
C31
C28
R12
6
C52
R12
7
C49
R128
C53
R63
R64
C13
R28
R1
C27
R53R55
R67
R60
R74
R77
R78
R80
R81
R82
R83
R90
R91
C33
R19
R22R23
R44
R52
R72R
59
C59
C105
C58
1-864-900-
11
11 1-864-900-
11
11
A(Page 24)
IC1 G-2IC2 B-11IC3 E-2IC6 D-1
Q1 B-4Q2 C-1Q3 C-1
• SemiconductorLocationRef. No. Location
2222
CDX-S2210/S2210S/S2210X/S2250EE/SW330
CDX-S2210/S2210S/S2210X/S2250EE/SW330
3-5. SCHEMATIC DIAGRAM – SERVO BOARD (1/2) – • See page 32 for IC Block Diagram. • See page 20 for Waveforms.
IC B/D
IC B/D
CN1
R6 R7
Q2 R86
R84
TP41
TP46
TP30
TP47
R22
R71R72
R26
R40
R44
C61
R25
R41
TP42
TP21 TP22
TP29
R23
R21
R24
TP93
TP101
R49
C59R131
R113
C5
C27
C23
C20C19
C17
C18
C21
C29
C35C32
C33
C72C80
Q3
C102
C53
C51
C49 C57
C48
C45
C42
FB2
FB3
C67
R52
C52C47
C16
C13
C31
R19
R46R45
FB4
R123
C36
R132
R5
R4
R51
R112
Q1
C9
TP37
TP38
TP39
TP40
IC6
R13
IC2
R1
C10
X2
C28
C24
C22
C4
C7
C101
TP12
TP13
TP20
TP18TP17
TP16
TP15
TP14
TP27
TP26
TP25
R125R126R127R128 R64
R62
R63
R61
R60
R59
C62
C58C60
C34
C41
C40
C39
C38
TP34
TP36
TP35
TP33
(Page 23)
23 23
CDX-S2210/S2210S/S2210X/S2250EE/SW330
CDX-S2210/S2210S/S2210X/S2250EE/SW330
3-6. SCHEMATIC DIAGRAM – SERVO BOARD (2/2) – • See page 31 for IC Block Diagram. • See page 20 for Waveforms. • See page 35 for IC Pin Descriptions.
IC B/D
R81
R82
R83
R55 TP
62TP53
TP51
TP49
TP48
TP44
TP65
TP64
TP63
R47
R73
R48
R50
R53
R11
R10
R8
R9
TP32
TP31
TP10
TP11
TP43
TP67
TP66
TP23
TP24
R11
6
R11
8
R11
9
R121
TP97
TP98
TP99
C106
C37
R78
R77
R91
R90
R80
R117R122
R42 R43
R74
R17
R16
C6
R100
R101
IC1
CN2
R12
TP7
TP6
TP9
TP8
SW4
SW1
SW3
SW2
M903
M901
M902
R2
R3
R120
IC3
C105
R28
X1
C43
C64
C65
C103
TP74
TP75
TP76
TP77
TP78
TP79
TP80
TP81
TP82
TP83
TP84
TP85
TP86
TP87
TP88
TP89
TP90
TP91
TP92
TP1
TP2
TP3
TP4
TP5
R58
R54
R56
R66
R68
R69
R67
R65
R57
R70
(Page 22)
2424
CDX-S2210/S2210S/S2210X/S2250EE/SW330
CDX-S2210/S2210S/S2210X/S2250EE/SW330
3-7. PRINTED WIRING BOARD – MAIN BOARD – • See page 19 for Circuit Boards Location. : Uses unleaded solder.1
7 2-345-298-01 PLATE (TU), GROUND8 A-1083-385-A MAIN BOARD, COMPLETE (S2210/SW330)8 A-1083-453-A MAIN BOARD, COMPLETE (S2210S/S2210X)8 A-1083-614-A MAIN BOARD, COMPLETE (S2250EE)F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
TU1 A-3220-961-A TUNER UNIT (TUX-032)#1 7-685-792-09 SCREW +PTT 2.6X6 (S)#2 7-685-790-01 SCREW +PTT 2.6X4 (S)#3 7-685-793-09 SCREW +PTT 2.6X8 (S)
40
CDX-S2210/S2210S/S2210X/S2250EE/SW330
4-2. FRONT PANEL SECTION
Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark
51 X-2024-506-1 BUTTON ASSY (S) (S2210X)51 X-2024-531-1 BUTTON ASSY (S) (S2210S/S2250EE)51 X-2025-194-1 BUTTON ASSY (S) (S2210/SW330)52 2-187-736-11 FILTER (IR) (S2210S/S2250EE)52 2-187-736-21 FILTER (IR) (S2210/S2210X/SW330)
53 2-187-738-01 SPRING (RELEASE)54 X-2048-526-1 PANEL SUB ASSY, FRONT (S2210S)54 X-2048-527-1 PANEL SUB ASSY, FRONT (S2210)54 X-2048-528-1 PANEL SUB ASSY, FRONT (S2210X)54 X-2048-529-1 PANEL SUB ASSY, FRONT (S2250EE)
54 X-2048-533-1 PANEL SUB ASSY, FRONT (SW330)55 2-187-737-01 PLATE (CD), LIGHT GUIDE56 1-780-199-11 CONDUCTIVE BOARD, CONNECTION
58
61
61
59
60
57
56
51
not supplied(KEY board)
LCD901
not supplied
not supplied
not supplied
not supplied
not supplied
not supplied
not supplied 52
5354
55
62 55
57 X-2023-711-1 HOLDER (LCD) ASSY58 2-187-728-01 PANEL, FRONT BACK59 X-2024-133-1 CASE ASSY (for FRONT PANEL)60 A-1083-387-A PANEL COMPLETE ASSY, FRONT (S2210)60 A-1083-455-A PANEL COMPLETE ASSY, FRONT (S2210S)
60 A-1083-603-A PANEL COMPLETE ASSY, FRONT (S2210X)60 A-1083-616-A PANEL COMPLETE ASSY, FRONT (S2250EE)60 A-1092-079-A PANEL COMPLETE ASSY, FRONT (SW330)61 3-250-543-31 SCREW (+B P-TITE M2)62 3-251-320-01 EMBLEM (NO. 2.5), SONY
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
not supplied(SENSOR board)
not supplied
not supplied
not supplied
not supplied
#4
101102
103
104
105
106
107
108
101 A-3372-455-A CHASSIS (T) SUB ASSY102 3-253-729-01 SPRING (LTR), TENSION COIL103 3-253-746-14 SPRING (DAMPER), COMPRESSION104 3-253-746-03 SPRING (DAMPER), COMPRESSION105 2-345-767-01 SPRING (KF60), TENSION
IC901 6-707-063-01 IC LC75826WH-US-EIC971 6-600-163-01 IC RS-770 (IR)
< JUMPER RESISTOR >
JP935 1-216-864-11 SHORT CHIP 0JP961 1-216-864-11 SHORT CHIP 0
< LIQUID CRYSTAL DISPLAY >
LCD901 1-805-765-11 DISPLAY PANEL, LIQUID CRYSTAL
< DIODE >
LED931 6-501-062-01 LED NSCW505CT-AST (LCD BACK LIGHT)LED932 6-501-062-01 LED NSCW505CT-AST (LCD BACK LIGHT)LED941 6-500-450-01 LED CL-195SR-CD-T (> M)
(EXCEPT SW330)LED941 6-500-510-01 LED CL-195PG-CD-T (> M) (SW330)LED942 6-500-450-01 LED CL-195SR-CD-T (m .)
(EXCEPT SW330)
LED942 6-500-510-01 LED CL-195PG-CD-T (m .) (SW330)
LED951 6-500-450-01 LED CL-195SR-CD-T (DISC-R) (EXCEPT SW330)LED951 6-500-510-01 LED CL-195PG-CD-T (DISC-R) (SW330)LED952 6-500-450-01 LED CL-195SR-CD-T (DISC-L) (EXCEPT SW330)LED952 6-500-510-01 LED CL-195PG-CD-T (DISC-L) (SW330)
FB1 1-469-844-11 INDUCTOR 2.2uHFB302 1-216-864-11 SHORT CHIP 0FB303 1-469-876-11 INDUCTOR, FERRITE BEADFB304 1-216-295-11 SHORT CHIP 0FB305 1-500-245-11 INDUCTOR, FERRITE BEAD
FB307 1-216-864-11 SHORT CHIP 0FB308 1-500-245-11 INDUCTOR, FERRITE BEADFB309 1-216-864-11 SHORT CHIP 0FB310 1-216-864-11 SHORT CHIP 0FB501 1-500-245-11 INDUCTOR, FERRITE BEAD
FB603 1-216-295-11 SHORT CHIP 0FB604 1-216-295-11 SHORT CHIP 0FB605 1-216-864-11 SHORT CHIP 0FB606 1-414-595-11 INDUCTOR, FERRITE BEAD
< IC >
IC401 6-705-372-01 IC BD3808FS-FE2IC501 6-804-912-01 IC MB90487APF-G-118-BND1IC602 8-759-659-13 IC PST3428ULIC750 6-705-360-02 IC TDA8588BJ/N2/R1
< JACK >
J1 1-815-185-13 JACK (ANTENNA)J330 1-774-698-11 JACK, PIN 2P (AUDIO OUT)
< JUMPER RESISTOR >
JC1 1-216-864-11 SHORT CHIP 0JC12 1-216-864-11 SHORT CHIP 0JC401 1-216-864-11 SHORT CHIP 0JC445 1-216-296-11 SHORT CHIP 0JC446 1-216-864-11 SHORT CHIP 0
JC501 1-216-296-11 SHORT CHIP 0JC503 1-216-296-11 SHORT CHIP 0JC504 1-216-864-11 SHORT CHIP 0
JC506 1-216-864-11 SHORT CHIP 0JC511 1-216-296-11 SHORT CHIP 0
JC527 1-216-821-11 METAL CHIP 1K 5% 1/10WJC533 1-216-864-11 SHORT CHIP 0JC581 1-216-296-11 SHORT CHIP 0JC681 1-216-864-11 SHORT CHIP 0JC753 1-216-296-11 SHORT CHIP 0
JC754 1-216-296-11 SHORT CHIP 0JC755 1-216-296-11 SHORT CHIP 0JC756 1-216-864-11 SHORT CHIP 0
SUPPLEMENT-1File this supplement with the service manual.
Subject : Production country change.
The CDX-S2210S and CDX-S2250EE models has been changed in the production country to Thailand from Chinese.This service manual, SUPPLEMENT-1 only contains the change.When servicing and inspecting, check the Model Number Label to see if the model is made in Thailand or Chinese.
DISCRIMINATION
CDX-S2210/S2210S/S2210X/S2250EE/SW330
9-879-323-81
MADE IN CHINA
CDX-S2210S ( China production model ) CDX-S2210S ( Thailand production model )
CDX-S2250EE ( China production model ) CDX-S2250EE ( Thailand production model )
2. EXPLODED VIEWS2-1. Main Section ..................................................................... 142-2. CD Mechanism Section (1) ............................................... 152-3. CD Mechanism Section (2) ............................................... 162-4. CD Mechanism Section (3) ............................................... 172-5. CD Mechanism Section (4) ............................................... 18
3. ELECTRICAL PARTS LIST ........................................ 19
3 3
CDX-S2210/S2210S/S2210X/S2250EE/SW330
CDX-S2210/S2210S/S2210X/S2250EE/SW330
• WAVEFORMS
— SERVO BOARD —
— MAIN BOARD —
• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRINGBOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note is printedin each block.)
For schematic diagrams.Note:• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolyticsand tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.• f : internal component.• C : panel designation.
For printed wiring boards.Note:• X : parts extracted from the component side.• Y : parts extracted from the conductor side.• a : Through hole.• : Pattern from the side which enables seeing.(The other layers' patterns are not indicated.)
• A : B+ Line.• B : B– Line.• H : adjustment for repair.• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.• CD mechanism (1/2), (2/2) sections no mark : CD PLAY• Main (1/3), (2/3), (3/3) sections no mark : FM
( ) : AM< > : CD PLAY
∗ : Impossible to measure• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-tion tolerances.
• Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal produc-tion tolerances.
• Circled numbers refer to waveforms.• Signal path.
J : CD PLAYF : FMf : AM
Caution:Pattern face side: Parts on the pattern face side seen from the(Side B) pattern face are indicated.Parts face side: Parts on the parts face side seen from the(Side A) parts face are indicated.
Note:The components identi-fied by mark 0 or dottedline with mark 0 are criti-cal for safety.Replace only with partnumber specified.
Note:Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepiéce portant le numérospécifié.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
not supplied(SENSOR board)
not supplied
not supplied
#4
101102
109
110
103
104
105
106
107
108
101 A-3372-444-A CHASSIS (T) SUB ASSY102 3-253-729-11 SPRING (LTR), TENSION COIL103 3-257-892-12 SPRING (DAMPER), COIL104 3-257-892-01 SPRING (DAMPER), COIL105 2-345-767-11 SPRING (KF60), TENSION
106 3-259-033-01 DAMPER (S)
107 2-587-505-01 SCREW108 A-1082-772-A SERVO BOARD, COMPLETE109 X-3384-088-2 LEVER (L) ASSY110 X-3384-089-2 LEVER (R) ASSY#4 7-627-552-87 SCREW, PRECISION +P 1.7X2.2
16
CDX-S2210/S2210S/S2210X/S2250EE/SW330
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
FB603 1-216-295-11 SHORT CHIP 0FB604 1-216-295-11 SHORT CHIP 0FB605 1-216-864-11 SHORT CHIP 0FB606 1-414-595-11 INDUCTOR, FERRITE BEAD
< IC >
IC401 6-705-372-01 IC BD3808FS-FE2IC501 6-804-912-01 IC MB90487APF-G-118-BNDE1IC602 8-759-659-13 IC PST3428ULIC750 6-705-360-02 IC TDA8588BJ/N2/R1
< JACK >
J1 1-815-185-13 JACK (ANTENNA)J330 1-774-698-11 JACK, PIN 2P (AUDIO OUT REAR)
< JUMPER RESISTOR >
JC1 1-216-864-11 SHORT CHIP 0JC12 1-216-864-11 SHORT CHIP 0JC401 1-216-864-11 SHORT CHIP 0JC445 1-216-296-11 SHORT CHIP 0JC446 1-216-864-11 SHORT CHIP 0
JC501 1-216-296-11 SHORT CHIP 0JC503 1-216-296-11 SHORT CHIP 0JC504 1-216-864-11 SHORT CHIP 0JC505 1-216-296-11 SHORT CHIP 0JC506 1-216-864-11 SHORT CHIP 0
JC511 1-216-296-11 SHORT CHIP 0JC527 1-216-821-11 METAL CHIP 1K 5% 1/10WJC533 1-216-864-11 SHORT CHIP 0JC681 1-216-864-11 SHORT CHIP 0JC753 1-216-296-11 SHORT CHIP 0
JC754 1-216-296-11 SHORT CHIP 0JC755 1-216-296-11 SHORT CHIP 0JC756 1-216-864-11 SHORT CHIP 0
Clicking the version allows you to jump to the revised page.Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
Ver. Date Description of Revision1.0 2004.12 New1.1 2005.05 Production country change. (Supplement-1) (ENG-05003)
1.2 2005.07 Change of CD mechanism. (Supplement-2) (ECN-ECB00626)
1.3 2005.11 NOTE FOR REPLACEMENT OF THE IC501 is added. (SPM-05015)