Kit Contents Item # Quantity Reqd. Description 1 1 “Y” Adapter 2 1 Wire harness 3 1 Hardware Kit 4 2 White Light Modules 5 1 Switch Kit 6 2 Amber cup holder kits 7 1 Customer Information card Hardware Bag Contents Item # Quantity Reqd. Description 1 4 Wire tie .0625 2 5 foam pads 3 2 T-Taps 4 4 Modules Screws Switch Bag Contents Item # Quantity Reqd. Description 1 1 Switch 2 1 End Cap, Black 3 1 Illumination Nameplate 4 1 Installation tool 5 1 Bezel 6 1 Black spacer Recommended tools Safety Tools Vehicle protection Safety glasses Special Tools Installation Tools Phillips screwdriver 1/4 inch jewelers Torque wrench 36in. lbs Nylon Removal Tool Pliers Diagonal cutter or wire tie tool Scissors Drill 1/8” Drill bit 1/2” Drill bit. UniBit or step drill rec. 9/32” Drill bit Scribe or Center punch Masking tape Color Applicability/Trim Level Accessory Color General Applicability All models of xB Recommended Sequence of Application Item # Accessory 1 * Overlay Apply any overlay first 2 3 *Mandatory SPECIAL NOTE: After TMS and Safety mandated preparatory steps have been taken, the installation sequence is the suggested method for completing the accessory installation. In some instances the suggested sequence is written for one associate to install and in others the sequence is given as part of a team accessory installation. Unless otherwise stated in the document, the associates may perform the installation steps in any order to make the installation as efficient as possible while maintaining consistent quality. Scion xB 2012- Interior Light Upgrade Part Number 00016-00095 Accesory Code: YI9 Legend Southeast Toyota Distributors, LLC Conflicts 1 of 9
9
Embed
Scion xB 2012- Interior Light Upgrade - Sparks Toyotatoyotaparts.sparkstoyota.com/install/00016-00095-xB2012.pdf · others the sequence is given as part of a team accessory installation.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Hardware Bag ContentsItem # Quantity Reqd. Description1 4 Wire tie .06252 5 foam pads3 2 T-Taps4 4 Modules Screws
Switch Bag ContentsItem # Quantity Reqd. Description1 1 Switch2 1 End Cap, Black3 1 Illumination Nameplate4 1 Installation tool5 1 Bezel6 1 Black spacer
Recommended toolsSafety ToolsVehicle protectionSafety glassesSpecial ToolsInstallation ToolsPhillips screwdriver 1/4 inch jewelersTorque wrench 36in. lbsNylon Removal ToolPliersDiagonal cutter or wire tie toolScissorsDrill1/8” Drill bit1/2” Drill bit. UniBit or step drill rec.9/32” Drill bitScribe or Center punchMasking tape
Color Applicability/Trim Level
AccessoryC
olor
General ApplicabilityAll models of xB
Recommended Sequence of ApplicationItem # Accessory1 * Overlay Apply any overlay first23
*Mandatory
SPECIAL NOTE: After TMS and Safety mandated preparatory steps have beentaken, the installation sequence is the suggested method forcompleting the accessory installation. In some instances thesuggested sequence is written for one associate to install and inothers the sequence is given as part of a team accessoryinstallation. Unless otherwise stated in the document, theassociates may perform the installation steps in any order to makethe installation as efficient as possible while maintaining consistentquality.
i. Cutoutenclosedpapertemplatelabeled“xBcupholder”.
ii. Aligntemplateasshownuseapunch/scribetomarkthecenteroftheholetobedrilled.(Fig.D2)
iii.Drillpilotholeswith1/8”drillbit.
iv.Finallydrillthepilotholewitha9/32”drillbit.
v. De-burrholeswithde-burringtool.
3. InsertLensfrominsideofcupholder.(Fig.D3)
4. FirmlypressLEDassemblyintolens.(Fig.D4)
5. Securewithfoampadasshown.(Fig.D5)
SECTIONII-InstallationProcedures
Fig.A1
� of 9
Fig.C1 Fig.D1
Fig.D2 Fig.D3
Fig.D4 Fig.D5
BOTTOM
Southeast Toyota Distributors, LLC
Fig. 1A
E. Install power Switch1. Drill hole for switch.
i. Trim plastic as shown. (Fig. E1)
ii. Cut out enclosed paper “xB switch” template.
iii. Place template so hole drilled will beoriented as pictured. (Fig. E2)
iv. Place template in area indicated. Use apunch or scribe to mark center of thehole to be drilled.
v. Using a 1/2” drill bit (Unibit or step drillis highly recommended), drill the switchhole.
2. Clean bezel surface to remove grease andwax.
i. Wipe the application area clean withalcohol and a clean no-scratch cloth
ii. Dry the installation area using a clean,dry, lint free cloth.
3. Insert switch bezel into switch plate. Bendthe switch plate slightly to match conture ofsurface. (Fig. E3)
SECTION II - Installation Procedures
3 of 9
6. Drill hole for i-Pod holder.
i. Cut out enclosed paper template labeled“xB i-Pod holder”.
ii. Align template as shown use a punch/scribe to mark the center of the hole tobe drilled. (Fig. D6)
iii. Drill pilot holes with 1/8” drill bit.
iv. Finally drill the pilot hole with a 9/32”drill bit.
v. De-burr holes with de-burring tool.
7. Insert Lens from inside of i-Pod holder.(Fig. D7)
8. Lamp will be installed when center consoleis installed.
Fig. D6
Fig. D7
Fig. E1 Fig. E2
Fig. E3
TOP
Southeast Toyota Distributors, LLC
Note: Only one lamp is used in the iPod holder. Cover the remaining lamp with electrical tape. (Fig. D8) Secure lamp to center insert with foam pad. (Fig. D9)
9. Only one lamp is used in i-Pod holder. See note on securing extra lamp. (Fig. D8-D9)
i. Aligntheprinting“ILLUMINATION”squaretotheconsole.(Fig.E5)
ii. Oncealigned,pressdownfirmlytoadheretape.
6. InstallSleevetobezel.
i. Removeabout5mmfromtheunpaintedportionofthespacer,ifanoverlayisap-pliedremoveanadditional3mm.The“white”inkendofthesleevemustbeinstalledagainsttheconsole.
7. Placewiresasshown.(Fig.E6)
F. Remove forward console1.Removeshiftbezel
i. Removeknobbyturningcounterclock-wise.(Fig.F1)
ii. Pryopenbootretainerandslidebootupwards.(Fig.F2)