Computer & Networking Minggu, 23 Juni 2013 TUGAS IV ROUTING STATIS DENGAN ROUTE SUMMARIZATION Route Summarization adalah meringkas settingan router statis pada router dengan syarat tertentu. Contoh: apabila ada 2 IP 192.168.1.0 dan 192.168.2.0 dan berada di subnet mask 255.255.255.0 (/24) maka bisa di singkat dengan 192.168.0.0 dengan subnet mask 255.255.252.0 (/22), untuk perhitungan nya lihat gambar di bawah ini : Selanjutnya lihat gambar topologi dibawah ini dengan menggunakan Packet tracer.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Computer & NetworkingMinggu, 23 Juni 2013
TUGAS IVROUTING STATIS DENGAN ROUTE SUMMARIZATION
Route Summarization adalah meringkas settingan router statis pada router dengan syarat tertentu. Contoh: apabila ada 2 IP 192.168.1.0 dan 192.168.2.0 dan berada di subnet mask 255.255.255.0 (/24) maka bisa di singkat dengan 192.168.0.0 dengan subnet mask 255.255.252.0 (/22), untuk perhitungan nya lihat gambar di bawah ini :
Selanjutnya lihat gambar topologi dibawah ini dengan menggunakan Packet tracer.
Langkah Pertama SettingRouter 1Router>enaRouter#conf t
Enter configuration commands, one per line. End with CNTL/Z.Router(config)#int fa0/0Router(config-if)#ip add 172.16.3.1 255.255.255.0 Router(config-if)#no shutRouter(config-if)#exitRouter(config)#int ser2/0Router(config-if)#ip add 172.16.2.1 255.255.255.0Router(config-if)#clock rate 64000Router(config-if)#no shutRouter(config-if)#exitRouter(config)#ip route 192.168.0.0 255.255.252.0 ser2/0 (Route Summarization)Router(config)#ip route 172.16.1.0 255.255.255.0 ser2/0Router(config)#exitRouter 2Router>enaRouter#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#int fa 0/0Router(config-if)#ip add 172.16.1.1 255.255.255.0Router(config-if)#no shutRouter(config)#int ser 2/0Router(config-if)#ip add 172.16.2.2 255.255.255.0Router(config-if)#clock rate 64000Router(config-if)#no shutRouter(config-if)#exitRouter(config)#int ser3/0Router(config-if)#ip add 192.168.1.2 255.255.255.0Router(config-if)#clock rate 64000Router(config-if)#no shutRouter(config-if)#exitRouter>enaRouter#conf tRouter(config)#ip route 172.16.3.0 255.255.255.0 ser 2/0Router(config)#ip route 192.168.2.0 255.255.255.0 ser3/0Router 3Router>enaRouter#conf tRouter(config)#int fa0/0Router(config-if)#ip add 192.168.2.1 255.255.255.0Router(config-if)#no shutRouter(config-if)#exitRouter(config)#exitRouter#conf tRouter(config)#int ser 2/0Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no shutRouter(config)#exitRouter>enaRouter#conf tRouter(config)#ip route 172.16.0.0 255.255.252.0 ser2/0 (Route Summarization)Router(config)#exitCek Router dengan perintah: Router>show ip route
Selanjutnya setting ip address dan Gateway di masing - masing pc sesuai dengan router yang terhubung.PC 1IP address : 172.16.3.2Subnet Mask : 255.255.255.0Gateway : 172.16.3.1PC 2IP address : 172.16.1.2Subnet Mask : 255.255.255.0Gateway : 172.16.1.1PC 3IP address : 192.168.2.2Subnet Mask : 255.255.255.0Gateway : 192.168.2.1Setelah Setting PC selesai, selamjutnya Cek dengan Perintah PING ke masing - masing PC.Hasil Ping PC 1 ke PC 3
Diposkan oleh 11.240.0294 di 00.26
Reaksi:Tidak ada komentar: Kirimkan Ini lewat EmailBlogThis!Berbagi ke TwitterBerbagi ke FacebookBagikan ke PinterestLabel: Jarkom
VLSM adalah teknik yang memungkinkan administrator jaringan untuk membagi ruang alamat IP ke subnet yang berbeda ukuran, tidak seperti ukuran Subnetting. Untuk menyederhanakan VLSM adalah dengan memecah alamat IP ke subnet (beberapa tingkat) dan mengalokasikan sesuai dengan kebutuhan individu pada jaringan. Hal ini juga dapat disebut IP tanpa kelas pengalamatan. Sebuah classful menangani mengikuti aturan umum yang telah terbukti berjumlah pemborosan alamat IP.Contoh kasus:Ada Sebuah Perusahaan Konveksi, memiliki kantor pusat di Semarang dengan tiga kantor cabang yaitu di : Pekalongan, Kudus dan Solo.Perusahaan tersebut akan membangun sebuah jaringan komputer dengan kebutuhan host sebagai berikut :
a. Semarang : 58 hostb. Pekalongan : 26 hostc. Kudus : 10 hostd. Solo : 10 host
Perhitungan pembangunan host pada perusahaan tersebut:
1. Mengasumsikan jumlah jaringan yang akan dibangun :Host : 104 hostRouter : 3 X 2 = 6 hostJumlah : 110 host
192.168.1.01.SemarangKebutuhan host : 58Host yang ada : 62Network : 192.168.1.0 /26Host : 192.168.1.1 s/d 192.168.1.62Broadcast : 192.168.1.63Seluruh Network 192.168.1.0 /26 digunakan dan habis.
192.168.1.64 /26Network 192.168.1.64 /26 adalah 62 host digunakan untuk pekalongan 262.PekalonganKebutuhan host : 26Host yang ada : 30Network : 192.168.1.64 /27Host : 192.168.1.65 s/d 192.168.1.94Broadcast : 192.168.1.95Sisa network 192.168.1.64 /26 digunakan untuk kudus dan solo masing-masing 10
3.Kudus dan SoloKudus :Kebutuhan host : 10Host yang ada : 14Network : 192.168.1.96 /28Host : 192.168.1.97 s/d 192.168.1.110Broadcast : 192.168.1.111
Solo :Kebutuhan host : 10Host yang ada : 14Network : 192.168.1.112 /28
Host : 192.168.1.113 s/d 192.168.1.126Broadcast : 192.168.1.127Seluruh Network 192.168.1.64 /26 digunakan dan habis.192.168.1.128 /26Network 192.168.1.128 /26 adalah 62 host digunakan untuk 3 buah WAN
WAN IKebutuhan host : 2Host yang ada : 2Network : 192.168.1.128 /30Host : 192.168.1.129 s/d 192.168.1.130Broadcast : 192.168.1.131
WAN IIKebutuhan host : 2Host yang ada : 2Network : 192.168.1.132 /30Host : 192.168.1.133 s/d 192.168.1.134Broadcast : 192.168.1.135
WAN IIIKebutuhan host : 2Host yang ada : 2Network : 192.168.1.136 /30Host : 192.168.1.137 s/d 192.168.1.138Broadcast : 192.168.1.139Sisa host 192.168.1.140 – 192.168.1.191Diposkan oleh 11.240.0294 di 00.23
Reaksi:Tidak ada komentar: Kirimkan Ini lewat EmailBlogThis!Berbagi ke TwitterBerbagi ke FacebookBagikan ke PinterestLabel: Jarkom
Minggu, 28 April 2013
TUGAS IIVLAN
TOPOLOGIBerikut adalah gambar topologi jaringannya :
KONFIGURASI PADA SWITCH 0
KONFIGURASI PADA SWITCH 1
KONFIGURASI PADA ROUTER
HASIL UJI COBA SAMBUNGAN (PING)
1. Hasil ping dari PC0 ke PC1 (192.168.10.2 ke 192.168.20.2)
2. Hasil ping dari PC0 ke PC2 (192.168.10.2 ke 192.168.10.3)
3. Hasil ping dari PC0 ke PC3 (192.168.10.2 ke 192.168.20.3)
Diposkan oleh 11.240.0294 di 00.20
Reaksi:Tidak ada komentar: Kirimkan Ini lewat EmailBlogThis!Berbagi ke TwitterBerbagi ke FacebookBagikan ke PinterestLabel: Jarkom
Minggu, 17 Maret 2013
TUGAS I KUMPULAN PERINTAH
CISCO ROUTER
Berikut adalah kumpulan perintah penuh, perintah singkat, dan maksud berbagai perintah "Show" pada router CISCO:
Perintah Penuh Perintah Singkat Maksud Perintah
show running-config sh ru
Menampilkan konfigurasi yang sedang berjalan di RAM. Termasuk host name, passwords, interface IP addresses, routing protocol yang aktif, DHCP dankonfigurasi NAT. Dapat dijalankan di EXEC mode.
Perintah Penuh Perintah Singkat Maksud Perintah
show startup-config sh st Menampilkan konfigurasi yang tersimpan di NVRAM
Perintah Penuh Perintah Singkat Maksud Perintahshow version sh v Menampilkan versi Cisco IOS, uptime dari
penerus, bagaimana router dimulai, dari mana sistem ini diambil, interface POST
ditemukan, dan konfigurasi register
Perintah Penuh Perintah Singkat Maksud Perintah
show ip protocols sh ip p Memperlihatkan ip protokol routing yang telah dikonfigurasi dan yang sedang berjalan
Perintah Penuh Perintah Singkat Maksud Perintahshow ip route sh ip ro Melihat tabel ip/konfigurasi routing
Perintah Penuh Perintah Singkat Maksud Perintah
show interfaces sh in Menunjukkan interface yang berjalan di router
Perintah Penuh Perintah Singkat Maksud Perintahshow ip interface brief ship i b Tinjauan semua antarmuka pada router
Perintah Penuh Perintah Singkat Maksud Perintah
show protocols sh protMenampilkan status interface baik secara global maupun khusus dari protokol layer 3 yang terkonfigurasi
Perintah Penuh Perintah Singkat Maksud Perintah
show cdp neighbors sh cd ne Menunjukkan router yang langsung terhubung jaringan tetangga
Perintah Penuh Perintah Singkat Maksud Perintahshow sessions sh se Melihat sesi yang ada saat ini
Perintah Penuh Perintah Singkat Maksud Perintahshow ssh sh ss Menampilkan operasi status pengoperasian
SSH
Perintah Penuh Perintah Singkat Maksud Perintah
ping p Memastikan apakah sebuah device tertentu dalam jaringan itu ada dan terhubung.
Perintah Penuh Perintah Singkat Maksud Perintah
traceroute tr
Menunjukkan rute yang dilewati paket untuk mencapai tujuan. Ini dilakukan dengan mengirim pesan Internet Control Message Protocol (ICMP) Echo Request ke tujuan dengan nilai Time to Live yang semakin meningkat.
Diposkan oleh 11.240.0294 di 00.13
Reaksi:Tidak ada komentar: Kirimkan Ini lewat EmailBlogThis!Berbagi ke TwitterBerbagi ke FacebookBagikan ke PinterestLabel: Jarkom
Kamis, 28 Juni 2012
Evaluasi CCNA Discovery 1 Chapter 7 1. Why is IEEE 802.11 wireless technology able to transmit further distances than Bluetooth technology?
transmits at much lower frequencies
has higher power output
transmits at much higher frequencies
uses better encryption methods
2. What are three advantages of wireless over wired technology?
more secure , longer range and anytime, anywhere connectivityanytime, anywhere connectivity , easy and inexpensive to install and ease of using licensed air spacelonger range , easy and inexpensive to install and ease of adding additional devicesanytime, anywhere connectivity , easy and inexpensive to install and ease of adding additional devices
3. What are two benefits of wireless networking over wired networking?
speed and security
security and mobility
mobility and reduced installation time
reduced installation time and allows users to share more resources
4. A technician has been asked to provide wireless connectivity to the wired Ethernet network of a building. Which three factors affect the number of access points needed?
the size of the building, the number of solid interior walls in the building and the presence of microwave ovens in several officesthe size of the building, the encryption method used on the wireless network and the use of both Windows and Appletalk operating systemsthe use of both Windows and Appletalk operating systems , the number of solid interior walls in the building and the use of shortwave or infrared on the APthe use of shortwave or infrared on the AP , the presence of microwave ovens in several offices and the number of solid interior walls in the building
5. Why is security so important in wireless networks?
Wireless networks are typically slower than wired networks.
Televisions and other devices can interfere with wireless signals.
Wireless networks broadcast data over a medium that allows easy access.
Environmental factors such as thunderstorms can affect wireless networks.
6. What does the Wi-Fi logo indicate about a wireless device?
IEEE has approved the device.
The device is interoperable with all other wireless standards.The device is interoperable with other devices of the same standard that also display the Wi-Fi logo.The device is backwards compatible with all previous wireless standards.
7. Which statement is true concerning wireless bridges?
connects two networks with a wireless link
stationary device that connects to a wireless LAN
allows wireless clients to connect to a wired network
increases the strength of a wireless signal
8. Which WLAN component is commonly referred to as an STA?
cell
antenna
access point
wireless bridge
wireless client
9. Which statement is true concerning an ad-hoc wireless network?
created by connecting wireless clients in a peer-to-peer network
created by connecting wireless clients to a single, centralized AP
created by connecting multiple wireless basic service sets through a distribution system
created by connecting wireless clients to a wired network using an ISR
10. Refer to the graphic. In the Wireless menu option of a Linksys integrated router, what does the Network Mode option Mixed mean?
The router supports encryption and authentication.
The router supports both wired and wireless connections.
The router supports 802.11b, 802.11g, and 802.11n devices.
The router supports connectivity through infrared and radio frequencies.
11. Refer to the graphic. In the Wireless menu of a Linksys integrated router, what configuration option allows the presence of the access point to be known to nearby clients?