Machining Conditions *For all material types and standards, see pages 240 to 245. ® Material Group Group Material Brinell hardness HB d.o.c [mm] feed [mm/rev] A max V c [m/min] Optimal cutting No Examples* min max min max [mm 2 ] min max d.o.c feed Ck 15 150 2.0 0.35 0.64 350 Low Carbon 1 9SMnPb28 180 0.50 2.0 0.35 0.64 180 280 0.5to 2 0.35 Steel 210 1.5 0.35 0.56 250 42 CrMo 4 180 2.0 0.30 0.56 280 Alloy Steel 2 100 Cr 6 230 0.50 2.0 0.30 0.48 120 250 0.5to 2 0.30 32 NiCrMo 14.5 280 2.0 0.30 0.40 210 320 1.5 0.25 0.32 180 X38 CrMoV 5 220 2.0 0.30 0.48 190 High Alloy 3 X210 CrW 12 280 0.50 2.0 0.30 0.40 70 150 0.5to 2 0.28 Steel X90 CrMoV 8 320 1.5 0.30 0.32 130 350 1.5 0.25 0.24 100 4 303 / 304 210 2.0 0.25 0.32 170 270 0.5to 2 0.35 Austenitic 304 L to 250 5 316 / 316 L 230 0.50 2.0 0.14 0.18 0.24 120 210 0.5to 2 0.32 Stainless Steel to 270 6 316 Ti --------- 1.5 0.13 0.18 0.24 70 120 0.5to 2 0.28 630 (F16PH) Ferritic 7 430 / 439 / 444 Annealed 0.50 2.0 0.13 0.20 0.32 170 250 0.5to 2 0.32 Stainless Steel Martensitic 8 410 / 420 0.50 2.0 0.15 0.20 0.32 170 250 0.5to 2 0.32 Stainless Steel Treated 120 210 EN - GJL 200 140 0.80 280 Grey Cast Iron 9 EN - GJL 250 to 230 0.50 2.0 0.15 0.45 0.72 170 250 0.5to 2 0.35 EN - GJL 300 0.72 230 Nodular Cast EN - GJS 400 210 0.60 230 Iron 10 EN - GJS 600 260 0.50 2.0 0.11 0.35 0.52 120 190 0.5to 2 0.30 EN - GJS 800 310 0.48 150 Inconel 625 0.20 35 11 Inconel 718 -------- 0.50 1.5 0.13 0.18 0.20 25 40 0.5to 2 0.28 Hastello y C 0.24 65 12 TiAl 6 V4 -------- 0.50 1.5 0.13 0.18 0.24 35 60 0.5 to 2 0.30 T40 0.24 28 40 0.28 conditions Nickel Based Alloys Titanium Based Alloys Annealed 0.11 0.15 0.13 0.13 0.15 40 28 0.5to 2 0.15 RCMT 0602 M0 RCMT 0602 M0 Super Finishing Finishing Semi Finishing Roughing Interrupted Cut 2 3 4 2 3 4 2 3 4 2 3 4 2 3 4 Insert designation 53 RCMT
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
SwissMade Machining Recommendations Guide - please see page 6
Machining Conditions
*For all material types and standards, see pages 240 to 245.
®
� Not recommended2 Acceptable3 Recommended4 Excellent
RCMT Shape
Clearance Angle
Tolerance
Insert Type
RCMT 0602 M0
RCMT 0803 M0
RCMT �0T3 M0
RCMT �204 M0
Super Finishing Finishing Semi Finishing Roughing Interrupted Cut
� 2 3 4 � 2 3 4 � 2 3 4 � 2 3 4 � 2 3 4
Insert designation
Application Guide
* For Cutting data see relevant page
Insert Designation Grade d s r Catalog Nr. Page*
R
C
M
T
Round
7° Positive rake
l ± 0.05 s ± 0.13
Screw down clamping Single sided
Turning
RCMT 0602 M0
RCMT 0803 M0
RCMT �0T3 M0
RCMT �204 M0
LT 10
LT 10
LT 10
LT 10
T0000090
T0000091
T0000092
T0000093
53
54
55
56
06 2,38 3
08 3,18 4
10 3,97 5
12 4,76 6
Material Group Group Material Brinellhardness
HB
d.o.c [mm] feed [mm/rev] A max Vc [m/min] Optimal cutting
No Examples*min max min max
[mm2]min max d.o.c feed
Ck 15150 2.0 0.35 0.64 350
Low Carbon1
9SMnPb28180 0.50 2.0 0.35 0.64 180 280 0.5to 2 0.35
Steel210 1.5 0.35 0.56 250
42 CrMo 4180 2.0 0.30 0.56 280
Alloy Steel 2 100 Cr 6230
0.502.0 0.30 0.48
120250
0.5to 2 0.30
32 NiCrMo 14.5280 2.0 0.30 0.40 210
320 1.5 0.25 0.32 180
X38 CrMoV 5220 2.0 0.30 0.48 190
High Alloy3 X210 CrW 12
2800.50
2.0 0.30 0.4070
1500.5to 2 0.28
SteelX90 CrMoV 8
320 1.5 0.30 0.32 130
350 1.5 0.25 0.24 100
4303 / 304 210
2.0 0.25 0.32 170 270 0.5to 2 0.35
Austenitic
304 L to 250
5 316 / 316 L230
0.50 2.0
0.14
0.18 0.24 120 210 0.5to 2 0.32Stainless Steel to 270
6316 Ti
--------- 1.5
0.13
0.18 0.24 70 120 0.5to 2 0.28630 (F16PH)
Ferritic 7 430 / 439 / 444 Annealed 0.50 2.0
0.13
0.20 0.32 170 250 0.5to 2 0.32Stainless Steel
Martensitic8 410 / 420 0.50 2.0
0.15
0.20 0.32170 250
0.5to 2 0.32Stainless Steel Treated 120 210
EN - GJL 200140
0.80 280
Grey Cast Iron 9 EN - GJL 250to 230
0.50 2.0
0.15
0.45 0.72 170 250 0.5to 2 0.35
EN - GJL 300 0.72 230
Nodular CastEN - GJS 400 210 0.60 230
Iron10 EN - GJS 600 260 0.50 2.0
0.11
0.35 0.52 120 190 0.5to 2 0.30
EN - GJS 800 310 0.48 150
Inconel 625 0.20 35
11 Inconel 718 -------- 0.50 1.5 0.13 0.18 0.20
25
40 0.5to 2 0.28
Hastello y C 0.24 65
12TiAl 6 V4
-------- 0.50 1.5 0.130.18 0.24 35 60 0.5 to 2 0.30
T40 0.24 28 40 0.28
conditions
Nickel BasedAlloys
Titanium BasedAlloys
Annealed
0.11
0.15
0.13
0.13
0.15
40
28
0.5to 20.15
RCMT 0602 M0
RCMT 0602 M0
Super Finishing Finishing Semi Finishing Roughing Interrupted Cut
� 2 3 4 � 2 3 4 � 2 3 4 � 2 3 4 � 2 3 4
Insert designation
52 53
RCMT
Machining Conditions
*For all material types and standards, see pages 240 to 245.
®
Machining Conditions
*For all material types and standards, see pages 240 to 245.
®
Material Group Group Material Brinellhardness
HB
d.o.c [mm] feed [mm/rev] A max Vc [m/min] Optimal cutting
No Examples*min max min max
[mm2]min max d.o.c feed
Ck 15150 2.0 0.42 0.80 350
Low Carbon1
9SMnPb28180 0.50 2.0 0.42 0.80 180 280 0.5 to 2 0.35
Steel210 1.5 0.42 0.70 250
42 CrMo 4180 2.0 0.36 0.70 280
Alloy Steel 2 100 Cr 6230
0.502.0 0.36 0.60
120250
0.5 to 2 0.30
32 NiCrMo 14.5280 2.0 0.36 0.50 210
320 1.5 0.30 0.40 180
X38 CrMoV 5220 2.0 0.36 0.60 190
High Alloy3 X210 CrW 12
2800.50
2.0 0.36 0.5070
1500.5 to 2 0.28
SteelX90 CrMoV 8
320 1.5 0.36 0.40 130
350 1.5 0.30 0.30 100
4303 / 304 210
2.0 0.30 0.40 170 270 0.5 to 2 0.35
Austenitic
304 L to 250
5 316 / 316 L230
0.50 2.0
0.14
0.21 0.30 120 210 0.5 to 2 0.32Stainless Steel to 270
6316 Ti
--------- 1.5
0.13
0.21 0.30 70 120 0.5 to 2 0.28630 (F16PH)
Ferritic 7 430 / 439 / 444 Annealed 0.50 2.0
0.13
0.24 0.40 170 250 0.5 to 2 0.32Stainless Steel
Martensitic8 410 / 420 0.50 2.0
0.15
0.24 0.40170 250
0.5 to 2 0.32Stainless Steel Treated 120 210
EN - GJL 200140
1.00 280
Grey Cast Iron 9 EN - GJL 250to 230
0.50 2.0
0.15
0.54 0.90 170 250 0.5 to 2 0.35
EN - GJL 300 0.90 230
Nodular CastEN - GJS 400 210 0.75 230
Iron10 EN - GJS 600 260 0.50 2.0
0.11
0.42 0.65 120 190 0.5 to 2 0.30
EN - GJS 800 310 0.60 150
Inconel 625 0.25 35
11 Inconel 718 -------- 0.50 1.5 0.13 0.21 0.25
25
40 0.5 to 2 0.28
Hastello y C 0.30 65
12TiAl 6 V4
-------- 0.50 1.5 0.130.21 0.30 35 60 0.5to 2 0.30
T40 0.30 28 40 0.28
conditions
Nickel BasedAlloys
Titanium BasedAlloys
Annealed
0.11
0.15
0.13
0.13
0.15
40
28
0.5to 20.18
RCMT 0803 M0
RCMT 0803 M0
Super Finishing Finishing Semi Finishing Roughing Interrupted Cut
� 2 3 4 � 2 3 4 � 2 3 4 � 2 3 4 � 2 3 4
Insert designation
Material Group Group Material Brinellhardness
HB
d.o.c [mm] feed [mm/rev] A max Vc [m/min] Optimal cutting
No Examples*min max min max
[mm2]min max d.o.c feed
Ck 15150 3.0 0.50 1.1 350
Low Carbon1
9SMnPb28180 0.50 3.0 0.50 1.1 180 280 0.5 to 2 0.35
Steel210 2.0 0.50 1.0 250
42 CrMo 4180 3.0 0.45 1.0 280
Alloy Steel 2 100 Cr 6230
0.502.0 0.42 0.8
120250
0.5 to 2 0.30
32 NiCrMo 14.5280 2.0 0.42 0.7 210
320 2.0 0.35 0.6 180
X38 CrMoV 5220 2.0 0.45 0.8 190
High Alloy3 X210 CrW 12
2800.50
2.0 0.42 0.770
1500.5 to 2 0.28
SteelX90 CrMoV 8
320 1.5 0.42 0.6 130
350 1.5 0.35 0.4 100
4303 / 304 210
2.0 0.35 0.4 170 270 0.5 to 2 0.35
Austenitic
304 L to 250
5 316 / 316 L230
0.50 2.0
0.18
0.25 0.3 120 210 0.5 to 2 0.32Stainless Steel to 270
6316 Ti
--------- 1.5
0.16
0.25 0.3 70 120 0.5 to 2 0.28630 (F16PH)
Ferritic 7 430 / 439 / 444 Annealed 0.50 2.0
0.16
0.28 0.4 170 250 0.5 to 2 0.32Stainless Steel
Martensitic8 410 / 420 0.50 2.0
0.20
0.28 0.4170 250
0.5 to 2 0.32Stainless Steel Treated 120 210
EN - GJL 200140
1.4 280
Grey Cast Iron 9 EN - GJL 250to 230
0.50 2.0
0.20
0.63 1.3 170 250 0.5 to 2 0.35
EN - GJL 300 1.3 230
Nodular CastEN - GJS 400 210 1.1 230
Iron10 EN - GJS 600 260 0.50 2.0
0.14
0.49 0.9 120 190 0.5 to 2 0.30
EN - GJS 800 310 0.8 150
Inconel 625 0.3 35
11 Inconel 718 -------- 0.50 1.5 0.16 0.25 0.3
25
40 0.5 to 2 0.28
Hastello y C 0.3 65
12TiAl 6 V4
-------- 0.50 1.5 0.160.25 0.3 35 60 0.5 to 2 0.30
T40 0.3 28 40 0.28
conditions
Nickel BasedAlloys
Titanium BasedAlloys
Annealed
0.14
0.20
0.16
0.16
0.20
40
28
0.5 to 20.21
RCMT 10T3 M0
RCMT �0T3 M0
Super Finishing Finishing Semi Finishing Roughing Interrupted Cut
� 2 3 4 � 2 3 4 � 2 3 4 � 2 3 4 � 2 3 4
Insert designation
54 55
RCMT
Machining Conditions
*For all material types and standards, see pages 240 to 245.
®
Machining Conditions
*For all material types and standards, see pages 240 to 245.
®
Material Group Group Material Brinellhardness
HB
d.o.c [mm] feed [mm/rev] A max Vc [m/min] Optimal cutting
No Examples*min max min max
[mm2]min max d.o.c feed
Ck 15150 2.0 0.42 0.80 350
Low Carbon1
9SMnPb28180 0.50 2.0 0.42 0.80 180 280 0.5 to 2 0.35
Steel210 1.5 0.42 0.70 250
42 CrMo 4180 2.0 0.36 0.70 280
Alloy Steel 2 100 Cr 6230
0.502.0 0.36 0.60
120250
0.5 to 2 0.30
32 NiCrMo 14.5280 2.0 0.36 0.50 210
320 1.5 0.30 0.40 180
X38 CrMoV 5220 2.0 0.36 0.60 190
High Alloy3 X210 CrW 12
2800.50
2.0 0.36 0.5070
1500.5 to 2 0.28
SteelX90 CrMoV 8
320 1.5 0.36 0.40 130
350 1.5 0.30 0.30 100
4303 / 304 210
2.0 0.30 0.40 170 270 0.5 to 2 0.35
Austenitic
304 L to 250
5 316 / 316 L230
0.50 2.0
0.14
0.21 0.30 120 210 0.5 to 2 0.32Stainless Steel to 270
6316 Ti
--------- 1.5
0.13
0.21 0.30 70 120 0.5 to 2 0.28630 (F16PH)
Ferritic 7 430 / 439 / 444 Annealed 0.50 2.0
0.13
0.24 0.40 170 250 0.5 to 2 0.32Stainless Steel
Martensitic8 410 / 420 0.50 2.0
0.15
0.24 0.40170 250
0.5 to 2 0.32Stainless Steel Treated 120 210
EN - GJL 200140
1.00 280
Grey Cast Iron 9 EN - GJL 250to 230
0.50 2.0
0.15
0.54 0.90 170 250 0.5 to 2 0.35
EN - GJL 300 0.90 230
Nodular CastEN - GJS 400 210 0.75 230
Iron10 EN - GJS 600 260 0.50 2.0
0.11
0.42 0.65 120 190 0.5 to 2 0.30
EN - GJS 800 310 0.60 150
Inconel 625 0.25 35
11 Inconel 718 -------- 0.50 1.5 0.13 0.21 0.25
25
40 0.5 to 2 0.28
Hastello y C 0.30 65
12TiAl 6 V4
-------- 0.50 1.5 0.130.21 0.30 35 60 0.5to 2 0.30
T40 0.30 28 40 0.28
conditions
Nickel BasedAlloys
Titanium BasedAlloys
Annealed
0.11
0.15
0.13
0.13
0.15
40
28
0.5to 20.18
RCMT 0803 M0
RCMT 0803 M0
Super Finishing Finishing Semi Finishing Roughing Interrupted Cut
� 2 3 4 � 2 3 4 � 2 3 4 � 2 3 4 � 2 3 4
Insert designation
Material Group Group Material Brinellhardness
HB
d.o.c [mm] feed [mm/rev] A max Vc [m/min] Optimal cutting
No Examples*min max min max
[mm2]min max d.o.c feed
Ck 15150 3.0 0.50 1.1 350
Low Carbon1
9SMnPb28180 0.50 3.0 0.50 1.1 180 280 0.5 to 2 0.35
Steel210 2.0 0.50 1.0 250
42 CrMo 4180 3.0 0.45 1.0 280
Alloy Steel 2 100 Cr 6230
0.502.0 0.42 0.8
120250
0.5 to 2 0.30
32 NiCrMo 14.5280 2.0 0.42 0.7 210
320 2.0 0.35 0.6 180
X38 CrMoV 5220 2.0 0.45 0.8 190
High Alloy3 X210 CrW 12
2800.50
2.0 0.42 0.770
1500.5 to 2 0.28
SteelX90 CrMoV 8
320 1.5 0.42 0.6 130
350 1.5 0.35 0.4 100
4303 / 304 210
2.0 0.35 0.4 170 270 0.5 to 2 0.35
Austenitic
304 L to 250
5 316 / 316 L230
0.50 2.0
0.18
0.25 0.3 120 210 0.5 to 2 0.32Stainless Steel to 270
6316 Ti
--------- 1.5
0.16
0.25 0.3 70 120 0.5 to 2 0.28630 (F16PH)
Ferritic 7 430 / 439 / 444 Annealed 0.50 2.0
0.16
0.28 0.4 170 250 0.5 to 2 0.32Stainless Steel
Martensitic8 410 / 420 0.50 2.0
0.20
0.28 0.4170 250
0.5 to 2 0.32Stainless Steel Treated 120 210
EN - GJL 200140
1.4 280
Grey Cast Iron 9 EN - GJL 250to 230
0.50 2.0
0.20
0.63 1.3 170 250 0.5 to 2 0.35
EN - GJL 300 1.3 230
Nodular CastEN - GJS 400 210 1.1 230
Iron10 EN - GJS 600 260 0.50 2.0
0.14
0.49 0.9 120 190 0.5 to 2 0.30
EN - GJS 800 310 0.8 150
Inconel 625 0.3 35
11 Inconel 718 -------- 0.50 1.5 0.16 0.25 0.3
25
40 0.5 to 2 0.28
Hastello y C 0.3 65
12TiAl 6 V4
-------- 0.50 1.5 0.160.25 0.3 35 60 0.5 to 2 0.30
T40 0.3 28 40 0.28
conditions
Nickel BasedAlloys
Titanium BasedAlloys
Annealed
0.14
0.20
0.16
0.16
0.20
40
28
0.5 to 20.21
RCMT 10T3 M0
RCMT �0T3 M0
Super Finishing Finishing Semi Finishing Roughing Interrupted Cut
� 2 3 4 � 2 3 4 � 2 3 4 � 2 3 4 � 2 3 4
Insert designation
54 55
RCMT
Machining Conditions
*For all material types and standards, see pages 240 to 245.
®
SwissMade Machining Recommendations Guide - please see page 6
Material Group Group Material Brinellhardness
HB
d.o.c [mm] feed [mm/rev] A max Vc [m/min] Optimal cutting
No Examples*min max min max
[mm2]min max d.o.c feed
Ck 15150 4.0 0.70 1.6 350
Low Carbon1
9SMnPb28180 0.50 4.0 0.70 1.6 180 280 1.5 to 3 0.35
Steel210 3.0 0.70 1.4 250
42 CrMo 4180 4.0 0.60 1.4 280
Alloy Steel 2 100 Cr 6230
0.503.0 0.60 1.2
120250
1.5 to 3 0.30
32 NiCrMo 14.5280 3.0 0.60 1.0 210
320 2.5 0.50 0.8 180
X38 CrMoV 5220 3.0 0.60 1.2 190
High Alloy3 X210 CrW 12
2800.50
3.0 0.60 1.070
1501.5 to 3 0.28
SteelX90 CrMoV 8
320 2.0 0.60 0.8 130
350 2.0 0.50 0.6 100
4303 / 304 210
3.0 0.50 0.8 170 270 1.5 to 3 0.35
Austenitic
304 L to 250
5 316 / 316 L230
0.50 3.0
0.20
0.35 0.6 120 210 1.5 to 3 0.32Stainless Steel to 270
6316 Ti
--------- 2.0
0.18
0.35 0.6 70 120 1.5 to 3 0.28630 (F16PH)
Ferritic 7 430 / 439 / 444 Annealed 0.50 3.0
0.18
0.40 0.8 170 250 1.5 to 3 0.32Stainless Steel
Martensitic8 410 / 420 0.50 3.0
0.22
0.40 0.8170 250
1.5 to 3 0.32Stainless Steel Treated 120 210
EN - GJL 200140
1.8 280
Grey Cast Iron 9 EN - GJL 250to 230
0.50 3.0
0.22
0.90 1.6 170 250 1.5 to 3 0.35
EN - GJL 300 1.4 230
Nodular CastEN - GJS 400 210 1.5 230
Iron10 EN - GJS 600 260 0.50 3.0
0.15
0.70 1.3 120 190 1.5 to 3 0.30
EN - GJS 800 310 1.2 150
Inconel 625 0.5 35
11 Inconel 718 -------- 0.50 2.0 0.18 0.35 0.5
25
40 1.5 to 3 0.28
Hastello y C 0.6 65
12TiAl 6 V4
-------- 0.50 2.0 0.180.35 0.6 35 60 1.5 to 3 0.30
T40 0.6 28 40 0.28
conditions
Nickel BasedAlloys
Titanium BasedAlloys
Annealed
0.15
0.22
0.18
0.18
0.22
40
28
1.5 to 30.30
RCMT 1204 M0
RCMT �204 M0
Super Finishing Finishing Semi Finishing Roughing Interrupted Cut
� 2 3 4 � 2 3 4 � 2 3 4 � 2 3 4 � 2 3 4
Insert designation
SCMT Shape
Clearance Angle
Tolerance
Insert Type
Insert Designation Grade l s r Catalog Nr. Page*
S
C
M
T
Square 90°
0° No rake
l ± 0.08 m ± 0.13s ± 0.13
Pin / Top clamp Double sided
Turning
NN: All purpose chip breaker * For Cutting data see relevant page
SCMT 09T304 NN
SCMT 09T308 NN
LT 10
LT 10
T0001459
T0001458
58
59
9 4,76 0,4
9 4,76 0,8
90°
SCMT 09T304 NN
SCMT 09T308 NN
Super Finishing Finishing Semi Finishing Roughing Interrupted CutInsert designation
� 2 3 4 � 2 3 4 � 2 3 4 � 2 3 4 � 2 3 4
56 57
SCMT
Related Documents
![ベアリング用外径ホルダ[RCMTチップ用] レバーロック方式 - …RCMT 2525M-12BF 25 25 150 25 32 11 1204M0-BB 2020K-16BF 20 5 20 125 27 27 25 17 LL-2C LS-1T LR-16C](https://static.cupdf.com/doc/110x72/60b2d93aaf0e3e588401ba67/fffcfffrcmtffffc-ffffff-rcmt.jpg)