Quick Setup Guide for the HP AdvanceStack 10Base-T Hubs Installation details are provided in the HP AdvanceStack 10Base-T Hubs Installation and Reference Guide (5963-6554). Install the Hub 1. Install optional add-in modules, for example an HP Ethernet SNMP Module into the Expansion Slot. 2. Plug the power cord into the hub’s receptacle and into a properly grounded electrical outlet. The hub does not have a power switch; it is powered on when the power cord is plugged in. HP Ethernet SNMP Module Power receptacle on the back of the hub Thin LAN Extension Distributed Management RS-232 In Out 8 5 Reset Exp Slot Security Activity ThinLAN Console AUI/Xcvr Collision 10Base-T Hub-12 6 7 1 2 9 3 10 4 11 12 Power Fault AdvanceStack HP J2600A AUI/Xcvr Slot ThinLAN network port chain ports RS-232 console port optional AUI port module installed in AUI/Xcvr slot hub status LEDs and reset button twisted-pair port LEDs cable management guide power connector cover plate over slot for HP Ethernet SNMP Module redundant power connector
4
Embed
Quick Setup Guide - Hewlett Packardwhp-hou4.cold.extweb.hp.com/pub/networking/software/59636555.pdf · for the HP AdvanceStack 10Base-T Hubs Installation details are provided in the
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Quick Setup Guide for the HP AdvanceStack 10Base-T Hubs
Installation details are provided in the HP AdvanceStack 10Base-T Hubs Installation and
Reference Guide (5963-6554).
Install the Hub
1. Install optional add-in modules, for example anHP Ethernet SNMP Module into the ExpansionSlot.
2. Plug the power cord into the hub’s receptacleand into a properly grounded electrical outlet.The hub does not have a power switch; it ispowered on when the power cord is plugged in.
HP Ethernet SNMP Module
Power receptacle on the back of the hub
Thin LANExtension
Distributed ManagementRS-232
In Out
8 5Reset Exp Slot Security Activity
ThinLAN Console AUI/Xcvr Collision10Base-THub-12
67 129 310 41112Power
FaultAdvanceStack HP J2600A
AUI/XcvrSlot
ThinLANnetwork
port
chain ports RS-232 console port
optional AUI port moduleinstalled in AUI/Xcvr slot
hub status LEDs and reset button twisted-pair port LEDs
cable managementguide
power connector
cover plate overslot for HP Ethernet SNMP Module
redundant powerconnector
3.
Check the LEDs on the hub’s front panel. Whenthe hub is powered on, it performs a 3 to 60 second self-diagnostic test. When thetest completes, the following occurs:
– Power LED is on.– RPS LED is on if a Redundant Power Supply is connected (available at the end of 1995).– Fault LED is off.– If an SNMP Module is installed, the Exp Slot LED is on.
If the Fault LED stays on, the hub hasencountered an unrecoverable error. Seechapter 4, “Troubleshooting”.
4. Before mounting, unplug the hub.
5. Install the hub into a rack or cabinet followingpages 1-5 through 1-10 (in the accompanying hubmanual) and power the hub back on.
Hub-to-End Node Connection
1. Push the RJ-45 plug into the RJ-45 jack until thetab on the plug clicks into place.
2. Push the other end of the cable into the LANadapter in the end node such as a PC, printer, orprint server.
Status LEDs
B B24681012 1357911 10Base-THub-24
24681012
1357911
RJ-45 plug
unshielded twisted-paircable
Hub-to-Hub Connections
1. To connect the hub to another hub, push the“crossover” cable RJ-45 plug into the RJ-45 jackuntil the tab on the plug clicks into place.
2. Push the other end of the cable into theconnecting hub.
ThinLAN Backbone Connection
If you are connecting your hubs together on aThinLAN backbone, follow these steps:
1. Attach a ThinLAN cable section to one side of a BNC “T” connector.
2. Attach another ThinLAN cablesection or a 50-ohm terminator to the other side of the “T” connector.
3. Attach the “T” connector to theThinLAN port.
4. Cover the BNC connector with an insulating cover.
Note: Each ThinLAN cable segment must beterminated using a 50-ohm terminator at each end. Inthe illustration above, a 50-ohm terminator would beplaced on one side of the BNC “T” connector if thatconnector is at the end of the cable segment.