Festo AG & Co KG 3 1 1 Using RSL 3. Enter the following in th - Name for field bus no - Instances for inputs (1 - Instance for Configura - Data Format: SINT - Insert IP address Terminal with only out Activate Diagnose Inter I/O) or the Statusbits (+ For the input/output si Quick Gui CPX-FB36 Ether Allen Bradley co Start- 1. Dynamic addressing BOOTP/DHCP 2. Manual IP addressing Operating mode : Remote I/O Default See manual: Chapter 1.2 When FEC o is integrate Logix 5000 for EtherN he window “Module Properties ode 101) and outputs (100) with ac ation Assembly (102) with size tputs: rface (+ 2 Byte + 2 Bytes I) Terminal w Activate Dia (+ 2 ByteI/O izes see the Tip “CPX-FB36 I/O ide for rNet/IP with ontrollers -up hardware setting Additiona Diagnosti Bits: - deactiva M E co or CEC ed Quick Guide for CPX-F 2 4 S E D a G S A 1. A From You EDS In th Can Of “ Mod Net/IP s” ccording sizes e: 0 with only inputs: agnose Interface O) mapping” gs al ic ated Dev CPX M12 D-coded Ethernet onnection See See Status LEDs (see 4) FB36 2 4 General inform Setting up the network configur EDS available at www.festo.com EDS allows basic configu Documentations with detailed d available at the Festo Support P Go to www.festo.com/sp/cpx Search for: CPX-FB36 (manual): CPX-SYS (CPX-System Additional information about Et • www.odva.org Using RSLogix Add the CPX-FB36 as new modu 2. Use the profile “ m RSLogix Rev20 u can also use the S-File for configuration. his case “CPX-FB36” n be selected instead “Generic Ethernet dule” Using L device stat Modul status Network statu TP1/TP2 System failure Power system/ Modify status vice status X hardware status e manual: Chapter 3.1 e manual: Chapter 3.2 mation / preparation ration and parameters m/sp/cpx uration in the host-system descriptions are Portal. EN – 8024075 m manual): EN – 526446 therNet/IP can be found on: x 5000 for EtherNet/I ule above the Ethernet/IP bridg “Generic Ethernet Device” with LED’s for the tus identification Device status normal Device not ready us Device has connection Network ok, no connec Address problem or bu No Ethernet connectio Network ok Data traffic e OK Information Diagnostic Hardware defect /load Power ok Outside toleranc Ok Saved parameter Forced active Version A1 IP ge hin RSLogix n to PLC ction us off on ce rs
2
Embed
Quick Guide for - Pneumatic & electric automation ... AG & Co KG Quick Guide for CPX-FB36 Version A1 Tip Tip Tip Tip Tip Tip CPX-FB36 I/O mapping Using Boot DHCP SERVER to set the
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Festo AG & Co KG
3
1
1
Using RSLogix 5000 for EtherNet/IP
3. Enter the following in the window “Module Properties” - Name for field bus node - Instances for inputs (101 - Instance for Configuration Assembly ( - Data Format: SINT - Insert IP address
Terminal with only outputs:Activate Diagnose Interface (+ 2 Byte I/O) or the Statusbits (+ 2 Bytes I)
For the input/output sizes see the Tip “CPX
Quick Guide
CPX-FB36 EtherNet/IP with Allen Bradley controllers
Start-
1. Dynamic addressing BOOTP/DHCP
2. Manual IP addressing
Operating mode:
Remote I/O
Default
See manual: Chapter 1.2
When FEC or CEC is integrated
Using RSLogix 5000 for EtherNet/IP
3. Enter the following in the window “Module Properties”Name for field bus node
101) and outputs (100) with according sizesConfiguration Assembly (102) with size: 0
Terminal with only outputs: Activate Diagnose Interface (+ 2 Byte I/O) or the Statusbits (+ 2 Bytes I)
Terminal with only inputs:Activate Diagnose Interface (+ 2 ByteI/O)
For the input/output sizes see the Tip “CPX-FB36 I/O mapping”
Quick Guide for
EtherNet/IP with Allen Bradley controllers
-up hardware settings
Additional Diagnostic Bits: - deactivated
M12 DEthernet connection
When FEC or CEC integrated
Quick Guide for CPX-FB36
2
4
Setting up the network configuration and parameters EDS available at
Documentations with detailed descriptionsavailable atGo to Search for:
Additional information about
1. Add the CPX From RSLogix Rev20You can also EDSIn this case “CPXCan be selected instead Of “Generic Ethernet Module”
Using RSLogix 5000 for EtherNet/IP
3. Enter the following in the window “Module Properties”
with according sizes ) with size: 0
Terminal with only inputs: Activate Diagnose Interface (+ 2 ByteI/O)
I/O mapping”
up hardware settings
Additional Diagnostic
deactivated
Device status
CPX hardware status
M12 D-coded Ethernet connection
See manual: Chapter
See manual: Chapter 3.2
Status LEDs (see 4)
FB36
2
4
General information / preparation
Setting up the network configuration and parameters EDS available at www.festo.com/sp/cpx
EDS allows basic configuration in Documentations with detailed descriptionsavailable at the Festo Support Portal. Go to www.festo.com/sp/cpx Search for:
CPX-FB36 (manual): CPX-SYS (CPX-System manual):
Additional information about EtherNet/IP
• www.odva.org
Using RSLogix 5000 for
Add the CPX-FB36 as new module
2. Use the profile “Generic Ethernet Device”
From RSLogix Rev20 You can also use the EDS-File for configuration. In this case “CPX-FB36” Can be selected instead Of “Generic Ethernet Module”
Using LED’s for thedevice status
Modul status
Network status
TP1/TP2
System failure
Power system/load Modify status
Device status
CPX hardware status
See manual: Chapter 3.1
See manual: Chapter 3.2
General information / preparation
Setting up the network configuration and parameters
www.festo.com/sp/cpx EDS allows basic configuration in the host-system
Documentations with detailed descriptions are the Festo Support Portal.
EN – 8024075 System manual): EN – 526446
EtherNet/IP can be found on:
Using RSLogix 5000 for EtherNet/IP
new module above the Ethernet/IP bridge
“Generic Ethernet Device” within RSLogix
Using LED’s for the device status identification
Modul status Device status normal Device not ready
Network status
Device has connection to PLCNetwork ok, no connectionAddress problem or bus off
No Ethernet connectionNetwork ok Data traffic
System failure OK Information Diagnostic Hardware defect
Power system/load Power ok Outside toleranceOk
Saved parametersForced active
Version A1
EtherNet/IP
above the Ethernet/IP bridge
within RSLogix
connection to PLC Network ok, no connection Address problem or bus off
No Ethernet connection
Outside tolerance
Saved parameters
Festo AG & Co KG Quick Guide for CPX-FB36 Version A1
Tip Tip
Tip Tip
Tip
Tip
CPX-FB36 I/O mapping Using Boot DHCP SERVER to set the IP address
The ‘Boot DHCP SERVER’ tool recognizes BOOTP devices and enables an easy configuration of a static IP address for the CPX. 1. First start the Boot DHCP SERVER 2. Configure the network. 3. - In the window “Request History” you find all devices in the network - Via the MAC ID the Festo EtherNet/IP can be identified (MAC ID also on label) - Mark the node and press button “Add to relation list” Note: If you want that the settings available after power off/on then you must in the “Relation List” press “Disable BOOTP/DHCP”
Changing parameters of the CPX via L5K option
• Use CPX-MMI or FMT (Festo Maintenance Tool) with Ethernet connection to change parameters.
• In “ System parameter “ choose for the Start-UP parameter the
option -> “Saved parameter”
� Be carefully if you change the node. You might lose saved parameters.
� A lighting M-LED indicates stored parameter changes
After the right I/O mapping (see Point 3) you’ll find the process data inside the RSLogix project at the Controller-Tags fields. Example for Input 3 Byte and output 3 Byte: On click Controller-Tags -> Input data Output data data format: SINT Note: The configuration data “Festo:C” can be used for setting CPX-Parameters