Punch Art Lion Chocolate Slider - kintakards.webs.com Art Lion Chocolate Slider.pdf · • Cadbury Dairy Milk 100g Chocolate Block Step One: Slider box, adapted to fit Cadbury Dairy

Tutorial Created by Angela Purdie – www.kintakards.webs.com © KintaKards 2010

Tutorial Created by Angela Purdie – www.kintakards.webs.com © KintaKards 2010 Page: 1

Punch Art Lion – Chocolate Slider

– Tutorial by Angela Purdie Items you will need to complete this project: • 1 x 17.6cm x 18cm Chocolate Chip Cardstock • Black, Pretty in Pink, More mustard & Really Rust Cardstock • Snail adhesive, 2-way glue pen, Chocolate Chip ink and Sponge Dauber -

optional • White Gel Pen, Paper Snips • Stampin Write marker – Chocolate chip • Punches Used, Word Window, small heart from three heart

punch, ½” circle punch, 1 3/8” circle, five petal flower, wide oval, scallop circle, curly label Punch, slot punch.

• Cadbury Dairy Milk 100g Chocolate Block Step One: Slider box, adapted to fit Cadbury Dairy Milk 100g Chocolate Block Box Take your chocolate chip cardstock so that the 18cm is length, and 17.6cm is wide. Score downwards on the 18cm (Landscape), Score at 1cm, 2.3cm, 9.3cm, 10.6cm. Step Two:

• Along the bottom, score at 1cm, and using your papersnips, cut as pictured.

• Fold all your score lines, with bone folder.

• Add sticky strip to the length ways 1cm strip to make your

box.

• Add sticky strip and fold in the flaps to make the base Step Three: Take your slot punch, and punch where the ribbon will go.

Thread your ribbon through. Slide in the chocolate block. Tie in a bow and to remove the chocolate, grab hold of the bow and pull up, and out slides the chocolate.

Tutorial Created by Angela Purdie – www.kintakards.webs.com © KintaKards 2010

Tutorial Created by Angela Purdie – www.kintakards.webs.com © KintaKards 2010 Page: 2

Punch Art Lion

Step One: Take your punch pieces as pictured.

Using your paper snips, snip of four scallops from the Basic Black scallop circle punch piece – for the eyes and inner ears. . Optional: It wouldn’t be one of Punch Art projects if the pieces are not sponged. Sponge all you punch pieces – not black

Step Two: Take your two five petal punch pieces and adhere them on top of each other as pictured. And adhere ontop of the scallop circle punch piece.

Adhere the 1 3/8” circle punch piece ontop of the 5 petal pieces Using a 2-way glue pen, adhere two of the black scallops onto two of the ½” circles as pictured, And glue and slot them into behind the 1 3/8” circle peice to make the ears. To make the eyes, I have sniped off a bit more of the scallop slices and glued them to the head, as pictured. Dont worry about how it looks, the nose covers this.

To make the nose, take the word window piece, a ½” circle in pink and mustard and glue them behind the word window as pictured. Glue the small heart as pictured. Attach a dimensional and fix the nose to the head as pictured.

Tutorial Created by Angela Purdie – www.kintakards.webs.com © KintaKards 2010

Tutorial Created by Angela Purdie – www.kintakards.webs.com © KintaKards 2010 Page: 3

Step: 3 Attach a dimensional to the top of the wide oval punch piece, and affix the head to the body. Take your curly label punch piece to the body and glue on the paws as pictured. The stamp sets I have used is Vintage Labels and Short and Sweet stamp sets.

Using the white gel pen, add highlighting and using the Stampin’ Write Marker, add eyelashes and markings to the paws.

All finished –

Thank you very much, I hope you enjoyed putting this tutorial together. I also have various Punch Art Animal DIY kits on my website available to order. Please forward any comments or queries to [email protected] and be sure to check out my website (www.kintakards.webs.com) for more punch art projects or Stampin’ Up! Products to purchase. Regards Angela Purdie – KintaKards www.kintakards.webs.com