This is the manual for the PRS-%)%V ereader by sony. It's a hard-to-find thing now, thought I'd share it out here so everyone can always find it if needed. Manuals are hard to find after a few years. Hope Sony doesn't mind. I would hate to get sued for helping with their products.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
• SONY and the SONY logo are registered trademarks of Sony Corporation.• BBeB, BBeB Book, and their logos are trademarks of Sony Corporation.• “Memory Stick,” “Memory Stick Duo,” “Memory Stick PRO Duo,” and their logos are trademarks of Sony Corporation.• Bitstream is a registered trademark, and Dutch, Font Fusion, and Swiss are trademarks, of Bitstream Inc.• Microsoft, Windows, Windows Vista and Windows Media are trademarks or registered trademarks of Microsoft Corporation
in the United States and / or other countries.• Adobe, Adobe Reader and Adobe PDF are trademarks or registered trademarks of Adobe Systems Incorporated in the United
All other system names and product names appearing in this document are generally the registered trademarks or trademarks of their respective manufacturers. Further, the trademark TM and registered trademark ® symbols are not indicated throughout this document.
7. EXPLODED VIEWS7-1. Case Section ................................................................... 447-2. Main Section .................................................................. 45
8. ELECTRICAL PARTS LIST .............................. 46
TABLE OF CONTENTS Notes on chip component replacement• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Flexible Circuit Board Repairing• Keep the temperature of soldering iron around 270 °C during
repairing.• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY-RELATED COMPONET WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC-TIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON-NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
CAUTIONDanger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
PRS-505
3
SECTION 1SERVICING NOTES
UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARKUnleaded solder has the following characteristics.• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to
about 350 °C.Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!• Strong viscosity Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.
• Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
REWRITING THE LUTThe LUT is exclusive for each lot number of the INK INDICATOR ELEMENT ASSY. Therefore, when replacing the MAIN board, display panel, or FLASH ROM, you need to rewrite the LUT. However, rewriting is not required if the lot number is the same.
Location where the LUT is stored:• IC1203How to check the version of the stored LUT:• When you insert the memory stick or SD memory card in
which the exclusive fi le is stored, the test mode is established. Check the current LUT version displayed at the right side of “Update Waveform” as in the screen below. The LUT version is “8202191919” in this example.
(Screen display)
How to check the lot number of the ink (indication) ELEMENT ASSY:• The lot number is written on the label on the fl exible card wire.
The lot number is “P10” in the picture below.
main board
ink (indication) element assy
How to change the LUT:• Copy the LUT fi le you want to update to the folder under “/
Sony Reader/software” in the memory stick or SD memory card exclusive for the test mode, and then change the name to “lut.bin”. Execute test mode No.3 “Update Waveform”. The LUT will be updated in about 10 seconds, and the LUT version display will also change.
• For the LUT version and the LUT fi le corresponding to the lot number of the panel, refer to technical news.
Note: • To create the memory stick exclusive for the test mode, refer to TEST
MODE (Page 11).• For the VCOM adjustment value of RV1801 for each lot, refer to
ELECTRICAL ADJUSTMENT (Page 11).
PRS-505
4
• Removing the soft cover
Pull the tab of soft cover towards . Remove Sony’s Reader in the direction of .
• Attaching the soft cover
Insert the tab of the soft cover in the hole of Sony’s Reader.
Pull the tab of the soft cover towards . Insert Sony’s Reader in the direction of to attach it to the soft
cover. Check that the tabs of the soft cover are completely inserted in
the holes of Sony’s Reader.
Note: Note that the tab of the soft cover may become deformed, if you strongly pull the tab too much.
NOTE THE IC1001 ON THE MAIN BOARD REPLACINGReplacement of IC1001 on the MAIN board used in this set re-quires a special tool
NOTE THE IC301, IC953, IC1106, IC1201, IC1202 AND IC1203 ON THE MAIN BOARD REPLACINGWhen IC301, IC953, IC1106, IC1201, IC1202 and IC1203 on the MAIN board is damaged, exchange the new MAIN board for the MAIN board which IC damaged
NOTES WHEN REPLACING THE INK INDICATOR ELEMENT ASSY, MAIN BOARD AND FLASH ROM (IC1203)When the INK INDICATOR ELEMENT ASSY, MAIN board, or FLASH ROM (IC1203) is replaced, you need to change the LUT.
REMOVING/ATTACHING THE SOFT COVER
PRS-505
5
SECTION 2GENERAL
This section is extracted from instruction manual.
Guide to Parts and Controls
Front Enter button*1
To decide an item or apply a setting, press the Enter button.
/// buttons*1
To select an item or scroll around the screen, press (left), (up), (down), or (right).
*1 In this manual, the operation of the ////Enter buttons areexplained as follows.(Example) Press/// to select “Away” on the Book list, thenpress Enter.
Enter button
MENU buttonTo return to the previous screen or show a menu.
(page) / (>/<) buttonsTo turn the page or proceed/return to the next (>)/previous (<) content.
Number (1 – 9,0) buttonsTo select the numbered items on the screen or input numeric values on the Setting menu.
SD Memory Card slotTo insert a SD Memory Card (optional).
“Memory Stick Duo” slotTo insert a “Memory Stick Duo” (optional).
POWER switchTo switch on/off the Reader.
IndicatorLights up in red while charging, and goes off when charging is complete.Flashes in orange while the Reader is accessing yourcomputer via USB.Also flashes in orange while switching the Reader on or off.
Holes for soft cover attachmentThe soft cover is attached when purchased.
1
2
3
4
5
6
7
8
9
0
Folds open in use
Note• Do not leave the Reader in a high temperature conditions,
as it may damage the soft cover.
(size) buttonTo zoom in/out a page or picture.
(MARK) buttonTo create/remove a bookmark.
Hole for hand strapTo attach the hand strap.
USB connectorTo connect the USB cable (supplied).
DC IN jackTo connect the AC power adapter (optional).Hint• The Reader can be charged by connecting to a computer
VOLUME +/– buttonsTo adjust the volume.To mute the sound, press and hold the VOLUME +/– buttons. To restore the sound, press the VOLUME +/– buttons again.
Rear
Reset buttonTo reset the Reader if no operation is possible.
PRS-505
6
SECTION 3DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
Note 1: The process described in can be performed in any order. Note 2: Without completing the process described in , the next process can not be performed. Note 3: Please refer to SERVICING NOTES “REMOVING/ATTACHING THE SOFT COVER” (page 4).
Remove while moving ornamental plate (upper) assy in the direction of the arrow.
Note: When peeling off adhesive sheet, be sure to exchange it for new adhesive sheet.
PRS-505
7
3-3. ORNAMENTAL PLATE (LOWER) ASSY
3-4. MAIN ASSY
claw
ornamental plate (lower) assy
two claws
screw (M1.4)
two screws (M1.4)
The lower part of the back side
Please draw out main assy to the half noting that KEY FLEXIBLE board does not stretch in the direction of the arrow.
three tapping screws
Please open the lower side of case assy a little up and down.
Please draw out main assy from case assy in the direction of the arrow completely after removing the connector (CN801).
Please insert paper and the film, etc. in the space of case assy not to be damaged of the display side of INK(indikation) element assy.
connector (CN801)
spacer (CON_key)
KEY FLEXIBLE board
case assyback side
PRS-505
8
3-5. (ION) STORAGE BATTERY ASSY
3-6. SLOT FLEXIBLE BOARD
two screws (M1.4)
(ion) storage battery assy
connector (CN401)
main assyback side
upper side
lower side
two screws (M1.4)
SLOT FLEXIBLE board
spacer (CON_SD)
connector (CN201)
main assyback side
lower side
upper side
PRS-505
9
3-7. CONNECT FLEXIBLE BOARD
3-8. FRAME
two screws (M1.4)
CONNECT FLEXIBLE board
spacer (CON_USB)
adhesive sheet (D)Note: When peeling off adhesive sheet, be sure to exchange it for new adhesive sheet.
connector (CN901)
main assyback side
lower side
upper side
shaft (spring)Note: Note the loss because it is likely to dash out when it removes.
compression springNote: Note the loss because it is likely to dash out when it removes.
adhesive sheet (A)Note: When peeling off adhesive sheet, be sure to exchange it for new adhesive sheet.
two adhesive sheets (B)Note: When peeling off adhesive sheet, be sure to exchange it for new adhesive sheet.
frame
nut plateNote: Note the loss.
screw (M1.4)
PRS-505
10
3-9. MAIN BOARD, INK (INDICATION) ELEMENT ASSY (IIE1)
screw (M1.4 × 2) MAIN board
connector (CN302)
ink (indication) element assy (IIE1)
PRS-505
PRS-505
1111
SECTION 4TEST MODE
HOW TO MAKE THE SD MEMORY CARD OR MEMORY STICK FOR TEST MODE USE ONLY 1. Ready for the SD memory card or memory stick.2. Make the new directly as “/Sony Reader/software” on the SD
memory card or memory stick.3. Download the as follow as the fi les from internet site, copy to
directly. Download fi les: autorun.xml, icon.png, key.png, lut.bin (If this download fi le’s name is different, change
to this name.)
HOW TO ENTER THE TEST MODE1. Insert the test mode SD memory card or memory stick.2. After a while, indicate the test mode menu, enter the test
mode.
1. Test Panel1. While the machine selected tab “Test Panel” in test mode
menu, press the [ENTER] button or [1] button.2. Screen is changed to the Test Panel.3. The display is changed so bellow with each time of pushing the
[>] button or [<] button of [PAGE].
WHITE LIGHT GRAY DARK GRAY BLACK>
<
> >
<
>
<<
4. It’s back to TEST MODE MENU when the [MENU] button. 5. After the end of test, a display of Test Panel on TEST MODE
MENU is changed to “Done” from “Not Yet”.
2. Check All Key1. In the state that a Check All Key tab of TEST MODE MENU
is selected, press the [ENTER] button or [2] button.2. The screen is switched into the Check All Key state.
1 2 3 4 5 6 7 8 9 0
UP
ENTER
DOWN
LEFT RIGHT
MENUMARK
SIZE
VOL-
VOL+
PREV
NEXT
NEXT
PREV
3. The display invert when each button is pushed, and the display is back to the all button.
4. After the end of test, a display of the right side of Test Panel on TEST MODE MENU is changed to “Done” from “Not Yet”.
3. Update WaveformIn this mode, it is possible to confi rm the variation of LUT (Look Up Table) and rewrite. The change of the LUT is required when a INK INDICATOR ELEMENT, MAIN BOARD and FLASH ROM (IC1203) are replaced. However, a INK INDICATOR ELEMENT is different from parameter by each lot number, therefore, rewrit-ing is not required if the lot number is the same. The lot number is written on the label on the fl exible board.
lot number
1. The current LUT version displayed at the right side of Update Waveform on TEST MODE MENU.
2. In the state that a Update Waveform tab is selected if it is press the [ENTER] button or [3] button, it starts rewriting LUT ver-sion.
Note: It is necessary to match the LUT version to the version in elation to the lot number of the INK INDICATOR ELEMENT. Refer to Technical News about details.
3. After a few minutes (about 10 seconds), the screen display is refreshed, a LUT version display of the right side of Update Waveform on TEST MODE MENU is refreshed.
4. Reset Screen LockThe screen lock can be compulsorily released.1. The current state of screen lock and the password are dis-
played on the right side of Reset Screen Lock of TEST MODE MENU.
2. In the state that the Reset Screen Lock tab of TEST MODE MENU is selected, press the [ENTER] button or [4] button.
3. The display on the right side of Reset Screen Lock is changed to “Off-0000”, so Screen Lock is unlocked .
5. Power Off1. In the state of a Power Off tab of TEST MODE MENU, press
the [ENTER] button or [5] button.2. After a while, the screen display is changed white, so power is
turned off.
6. Factory InitializeIt return to the state various setting are shipped in the factory. The fi le of Flash ROM deletes all fi les except fi le the factory is shipped. Please note it enough you operate this mode. 1. In the state of a Factory Initialize tab of TEST MODE MENU,
press the [ENTER] button or [6] button.2. Initialize end. After a while, the screen display is changed
white, so power is turned off.
SECTION 5ELECTRICAL ADJUSTMENT
VCOM VOLTAGE ADJUSTMENT Vcom voltage for the display panel varies for each panel. VCOM adjustment is required when replacing a board or panel.
Preparation:Voltage is generated only when the screen is changed, so theadjustment needs to be performed while changing the screen. Use the slideshow function to change the screen sequentially.1. With the “Settings” tab in the menu selected, press the [EN-
TER] button or the [0] button.2. With the “Slideshow” tab selected, press the [ENTER] button
or the [3] button.3. Set “Turn On, Slide Duration 05 seconds”, and press the [EN-
TER] button on OK.
Procedure:1. With the “Pictures” tab in the menu selected, press the [EN-
TER] button or the [9] button.2. Specify a desired screen, and press the [ENTER] button to
check that the slideshow starts.3. Observe the TP354 on an oscilloscope (refer to Fig.2), and use
RV1801 to adjust the voltage that is generated when the screen is changed so that it satisfi es the standard.
Standard: Written on the fl exible card wire of the display panel with a marker. (–1 V to –2.5 V) (Refer to following Fig.1)
(In case of Fig.1: The value of VCOM is –1.16 V.)
Fig. 1
500 mV/DIV, 200 ms/DIV
1 Vp-p660 ms
Fig. 2
Adjustment Location:– MAIN Board (Component Side) –
For Schematic Diagrams.Note:• All capacitors are in μF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics
and tantalums.• All resistors are in Ω and 1/4 W or less unless otherwise
specifi ed.• f : internal component.• C : panel designation.
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note is printed in each block.)
• A : B+ Line.• B : B– Line.• C : adjustment for repair.• Power voltage is dc 5.2V and fed with regulated dc power
supply from TP402 and TP400 on the MAIN board.• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions. no mark : POWER ON ( ) : AUDIO PLAY * : Impossible to measure (For this model, the voltage is produced only when the
screen is changed. Under the power on, there is a voltage that is not produced.)
• Voltages are taken with VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production
tolerances.• Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production
tolerances.• Circled numbers refer to waveforms.• Signal path. F : AUDIO L : VIDEO N : USB O : SD MEMORY CARD/MEMORY STICK DUO
For Printed Wiring Boards.Note:• Y : Parts extracted from the conductor side.• f : internal component.• : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.)
Caution:Parts face side:(Conductor side)Pattern face side: (Component side)
Parts on the parts face side seen from the pattern face are indicated.Parts on the pattern face side seen from the parts face are indicated.
Note: The components identi-fi ed by mark 0 or dotted line with mark 0 are criti-cal for safety. Replace only with part number specifi ed.
Note: Les composants identifi és par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le nu-méro spécifi é.
• Waveforms– MAIN Board –
• MAIN board is multi-layer printed board. However, the patterns of intermediate-layers have not been in-
cluded in diagrams.
• Lead layoutssurface
CSP (Chip Size Package) Lead layout of conventional IC
* Replacing of IC1001 on the MAIN board used in this set requires a special tool.
IC107(Audio play mode)
2 V/DIV, 50 ns/DIV89 ns
3.6 Vp-p
IC953 (XO)(USB connection state)
1 V/DIV, 20 ms/DIV
55.2 ms2.2 Vp-p
IC1001 (XTAL32K)
200 mV/DIV, 10 s/DIV
30.6 s0.6 Vp-p
IC801 (X2)
1 V/DIV, 20 s/DIV
30.8 s2.2 Vp-p
IC801 (OSC2)
1 V/DIV, 100 ns/DIV
204 ns3.1 Vp-p
C
K
• The voltage and waveform of CSP (chip size package) cannot be measured, because its lead is different feom that conventional IC.
* Replacing of IC1001 on the MAIN board used in this set requires a special tool.
Note: When IC301, IC953, IC1106, IC1201, IC1202 and IC1203 on the MAIN board is damaged, exchange the new MAIN board for the MAIN board which IC damaged.
6-10. SCHEMATIC DIAGRAM - MAIN Board (5/10) - • See page 15 for waveform. • See page 29 for IC Block Diagram.
Note: When IC953, IC1106 and IC1203 on the MAIN board is damaged, exchange the new MAIN board for the MAIN board which IC damaged.
(Page 26)
(Page 18)
(Page 23)
(Page 26)
(Page 23)
(Page 18)
(Page 27)
(Page 28)
(Page 19)
(Page 27)
(Page 24)
(Page 23)
(Page 26)
(Page 26)
(Page 26)
(Page 23)
(Page 18)
PRS-505
PRS-505
2323
TP1016
TP1017
TP1018
TP2006
TP2008
TP2007
TP1022
TP1024
TP1025
TP2011
R2105
R2102
Q1001
TP1023
R2010
C1029
RB2015 C1030
RB2014
R2527
R2216
L1002
L1003
C1005
C1006
C1003
C1004 TP1019
C1007
C1008 C1009 C1010 C1011 C1012
RB2010
RB2009
RB2008
C1013
C1014
C1015
C1016 R2268 C1017 C1018 L1004
R2119
R2215C1019
R2208
C1022
C1021C1020
R2267
R2239
R2219
R2238
TP2001
TP2002
TP2003
TP2004
R2264
TP2009
R2101
R20
21
C1023
R2013
R20
19
RB2016
C10
24
R20
20
TP20
10
RB
2005
RB
2003
RB
2004
RB
2002
RB
2001
RB
2006
TP113
C1031
R2214
C1034
C1035
C1036
RB2007
TP10
29
TP10
28
RB2013
RB2012
RB2011
C1025
TP15
85
TP15
40
TP1515
TP2005
C1032
C1033
TP1591
TP1027
TP1588
TP1589
TP1541
TP1586
C1028
IC1002
IC1001
R2104 R2103
X1002
V2
V2
VCORE
BOOT1
BOOT2
BOOT0
PA18
SDCKE1
RESET-SF
16M
10
1k
2SC4738F-Y/GR
PA20
680
0.1
470k 0.1
470k
330
10k
1006.3V
0.1
476.3V
0.1 GND
0.1
0.1 0.1 0.1 0.1 0.1
470k
470k
470k
0.1
0.1
0.1
0.1 100k 0.1 10
10k
10k0.1
100k
6p
6p0.1
100k
10k
10k
10k
TDI
TCK
TMS
TDO
100k
CLKO
1k
330
0.1
100
330
470k
0.1
330
PA14
100
100
100
100
100 330
PA14
0.1
10k
0.1
0.01
0.1
100
A0
A24
330
330
330
0.1
TRST
0.01
0.1
PB20
0.1
TMP75AIDR
MC9328MXLVP20R2
100 100
32.768KHz
PCA3PCORE
PCA3PIO
LCDBUS
V3
LED2-ORG
CLKO
SDCLK
MA10
MA11
DQM3
DQM2
DQM1
DQM0
SUB-TXDSUB-RXD
SUB-RTS
SUB-CTS
MSDET
M_RESET
POR
PCAUDIO
AUDIO2
AUDIO3
AUDIO1
GND
SDCKEO
#SDWE
#CAS
#RAS
#CS2
RY/#BY
VCORE
V2
SRDSP
STCK
STFS
STXD
VBUS
USBCRG
USBBOOT
SDWP
SDDET
SDINT
SRR5C
PCR5C
PCR5CCLK
PCSDCARD
PCMSCARD
USB20INT
CS1
CS4
CS3
CS5
EB2
HRESET
#CS0
R/#W
#OE
GND
D(31-0)
A(24-0)
NAND-ALE
NAND-CLE
NAND-CEO
A1
A2
A3
A4
A5
A6
A7
A8
A9
A1
0
A11
A12
A1
3
A14
A1
5
A1
6
A17
A1
8
A1
9
A2
0
A2
1
A2
2
A2
3
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D16
D17
D18
D19
D2
0
D2
1
D2
2
D2
3
D2
4
D2
5
D2
6
D2
7
D2
8
D2
9
D3
0
D31
TXD
RXD
RTS
CTS
RTS
PCAUDIO
AUDIO1
AUDIO2
AUDIO3
PCAUDIO
AUDIO1
AUDIO2
AUDIO3
USBCRG
USBBOOT
US
BC
RG
US
BB
OO
T
PC
LK
ER
R
RD
Y
ST
BY
SR
A3
P
PD
OE
LC
LK
FC
LK
PD
0
PD
1
PD
2
PD
3
PD
4
PD
5
PD
6
PD
7
PD
8
PD
9
PD
10
PD
11
PD
12
PD
13
PD
14
PD
15
CTS
TXD
RXD
SDA
SCL
OS
GND
VCC
A0
A1
A2
(6/10)
TEMPERATURESENSOR
MAIN CPU
LEDSWITCH
10μH
10μH
47μH
∗CSP
(Chip Size Package)
6-11. SCHEMATIC DIAGRAM - MAIN Board (6/10) - • See page 15 for waveform. • See page 29 for IC Block Diagram. • See page 34 for IC Pin Function Description.
Note: Replacement of IC1001 on the MAIN board used in this set requires a special tool.
(Page 21)
(Page 22)
(Page 22)
(Page 19)
(Page 22)
(Page 18)
(Page 22)
(Page 24)
(Page 25)
(Page 27)
(Page 26)
(Page 25)
(Page 19)
(Page 24)
(Page 18)
(Page 21)
PRS-505
PRS-505
2424
TP828
TP829
TP830
TP805
TP817
TP807
TP808
TP860
R807
D802
RB802
RB804
RB807
R836
R810
R817
R842
R82
1
R82
4
R84
0
TP801
R85
6
R816
R806 R802
TP80
2
Q80
2
C809
R827
R809
R828
R825
R801
IC802
C805
R829
R826
C802 C810 C807
C808
TP83
1
TP83
2TP
833
C806
C803
C80
4
RB808
R837
R808
R804
R803
TP80
9
TP81
0TP
811
TP81
2
TP81
3
TP81
4
TP81
5
TP81
6
Q801
RB803
R814
R813
R812
R811
R851
R833
TP806
C801
R815
R82
2
L801
RB
801
R85
7
S801
S874
S873
CN801
RB806
RB805
TP1523
TP1522
TP1521
TP1520
TP1519
TP1518
TP1517
TP1516
IC801
R805
X802
R819
C812C813 C811
X801
V1
470k
HN2S01FU-TE85R
100
100
22k
470k
100k
470k
100
470k
100
100
CTS
100
1k
470k10k
SS
M3K
03FE
(TP
L3)
0.1
100k
470k
100k
10k
10k
XC61CN2502NR
0.01
3.3k
22k
0.01 0.1 8p
8p 0.1
0.01
0.01
22k
470k
470k
100
100
3LP01S
100
1k
100
0
100
1k
1M
10
470k
11k
0
100
100
12P
22k
22k
HD64F38004FP10V-198
100
4.9152MHz
470k
32.768KHz
LOW-BATT-LI
PWRON
USBON
STAT1
STAT2
RESET
USBDET
ISET2
LED-VCC
SW-STBY
LED2-ORG
DCDET
GND
V1
BATT-DC
BATT-LI
USBCRG
SUB-CTS
SUB-TXD
SUB-RXD
P0R
M_RESET
USBBOOT
STAT1
GND
SUB-RTS
LED2-ORG
KS
I0
KS
I1
DCDET
RXD
TXD
KS
I2
CT
S
LOW-LI
PWRON
USBON
LO
W-L
I
STAT1
STAT2
USBBOOT
POR
M_RESET
USBDET
US
BD
ET
KS
I3
KS
I4
KS
I5
KS
I6
KS
I7
PWRON
M_RESET
RTS
CTS
USBCHG
USBBOOT
POR
KSO0
KSO1
KSO2
KSO1
KSO2
ISET2
TXD
RXD
US
BC
HG
KSO0
RTS
KSI6
KSI5
KSI4
KSI3
KSI2
KSI1
KSI0
KSI7
USBON
DC
DE
TX
1
X2
VS
S
OS
C2
OS
C1
TE
ST
POR
VC
C
V1
V2
V3
KEY_OUT7
KEY_OUT6
KEY_OUT5
KEY_OUT4
KEY_OUT3
KEY_OUT2
KEY_OUT1
KEY_OUT0KE
Y_
IN5
KE
Y_
IN4
KE
Y_
IN3
KE
Y_
IN2
KE
Y_
IN1
KE
Y_
IN0
KE
Y_
IN6 KEY_IN7
ST
BY
_S
W
LED_1
LED_2
AD_ON
VSS
RTS
RXD
TXD
AVCC
BATT-LI
CT
S
LO
W-B
AT
T-L
I
DC
DE
T
KEY-ON
KE
Y-I
NT
BA
TT
-DC
USBON
PWRON
STA
T1
STA
T2
USBBOOT
US
BC
HG
P95
KEYLED
P33
P34
P35
US
BD
ET
KSO0
KSO1
KSO2
KSI0
KSI1
KSI2
KSI3
KSI4
KSI5
KSI6
KSI7
NC
(7/10)
S
S
IRQAEC
IRQ0
AN0
AN2
WK
P3
RESET
VOL+
VOL-
KEY
Q801,802BATTERY
CONTROL SWITCH
VOLTAGE DETECTOR
FLEXIBLEBOARD
SUB CPU
XM_RESET
ISE
T2
ISE
T1
XR
ES
ET
ISE
T2
STA
T1
STA
T2
6-12. SCHEMATIC DIAGRAM - MAIN Board (7/10) - • See page 15 for waveform. • See page 34 for IC Pin Function Description.
(Page 27)
(Page 22)
(Page 27)
(Page 18)
(Page 27)
(Page 22)
(Page 27)
(Page 18)
(Page 23)
(Page 23)
(Page 20)
PRS-505
PRS-505
2525
TP1201L1201 C1219 C1218
C1205
C1208
C1209
C1214
C1217
C1213
C1211
C1204
C1202
C1203
C1200
TP15
06
TP15
07
TP15
08
TP15
09
TP15
10
TP15
11
TP15
12
TP15
13
IC1201
IC1202
GND
100.1
0.001
0.1
0.001
0.1
0.001
0.1
0.1
0.1
0.1
0.1
0.1
K4M561633G-BN75T
K4M561633G-BN75T
GND
MA11
MA10
#CAS
#RAS
SDCLK
SDCKEO
#CS2
#SDWE
DQM0
DQM1
DQM2
DQM3
V2
V2
A(24-0)
D(31-0)
V2
GND
A(24-0)
D(31-0)
D24
D25
D26
D27
D28
D29
D30
D31
A2
A3
A4
A5 A6
A7
A8
A9
A10
D0
D1
D2
D3
D4
D5
D6
D7 D8
D9
D10
D11
D12
D13
D14
D15
A6
A7
A8
A9
A12
A13
A12
A13
A2
A3
A4
A5
A14
A15
A14
A15
A10
D19
D20
D22
D23
D21
D18
D17
D16
(8/10)
SD-RAM
SD-RAM
22μH
CSP(Chip Size Package)
CSP(Chip Size Package)
(Page 23)
6-13. SCHEMATIC DIAGRAM - MAIN Board (8/10) -
Note: When IC1201 and IC1202 on the MAIN board is damaged, exchange the new MAIN board for the MAIN board which IC damaged.
(Page 27)
(Page 23)
(Page 26)
PRS-505
PRS-505
2626
IC1112
IC1113
IC1116
IC1117
R1103
IC1101
IC1102
IC1107
C1104
C1109
C1110
C1112C1101
C1115
C1114
C1103
L1101
C1108
TP1554
TP1546
TP1547
TP1548
TP1549
TP1550
TP1551
TP1552
TP1553
TP1555
TP1556
TP1557
TP1558
TP1559
TP1560
TP1561
TP1562
TP1563TP1564
TP1565TP1566
TP1567TP1568
TP1569TP1570
TP1571TP1572
TP1573
TP1575TP1576
TP1577
TP1578
TP1579
TP1580
TP1581
TP1582
TP1583
TP1584
TP1542
TP1543
TP1574
SN74LVC244APWR
SN74LVC244APWR
TC7SZ125FU
TC7SZ125FU
0
TC7MP245FK(EL)
TC7MP245FK(EL)
TC7MP01FK
0.1
0.1
0.1
0.110
0.01
0.01
0.1
0.1
R/#W
#OE
EB2
#CS0
CS1
CS3
CS4
BEB2
BOE
CS5
HRESET
BHRESET
BA(24-0)
BD(31-0)
#CS0
BR/W
CS1
HRESET
CS4
CS3
A(24-0)
D(31-0)
V2
GND
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
BD0
BD1
BD2
BD3
BD4
BD5
BD6
BD7
BD8
BD9
BD10
BD11
BD12
BD13
BD14
BD15
A2
A4
A6
A8
A10
A12
A14
A16
A18
A20
A22
A3
A5
A7
A9
A11
A13
A15
A17
A19
A21
A23
BA2
BA4
BA6
BA8
BA10
BA12
BA14
BA16
BA18
BA20
BA22
BA3
BA5
BA7
BA9
BA11
BA13
BA15
BA17
BA19
BA21
BA23
EB2
R/W
OE
EB2
R/W
OE
R/W
A1
BA1
DIR
A1
A2
A3
A4
A5
A6
A7
A8
GND
VCC
OE
B1
B2
B3
B4
B5
B6
B7
B8
DIR
A1
A2
A3
A4
A5
A6
A7
A8
GND
VCC
OE
B1
B2
B3
B4
B5
B6
B7
B8
1OE
1A1
2Y4
1A2
2Y3
1A3
2Y2
1A4
2Y1
GND
VCC
2OE
1Y1
2A4
1Y2
2A3
1Y3
2A2
1Y4
2A1
1OE
1A1
2Y4
1A2
2Y3
1A3
2Y2
1A4
2Y1
GND
VCC
2OE
1Y1
2A4
1Y2
2A3
1Y3
2A2
1Y4
2A1
GND
VCC
GND
VCC
(9/10)
BUFFER
BUFFER
BUFFER
BUFFER
BUFFER
AND GATE, INVERTER
VCC
GND
BUFFER
22μH
(Page 22)
6-14. SCHEMATIC DIAGRAM - MAIN Board (9/10) - • See page 29 for IC Block Diagram.
(Page 25)
(Page 22)
(Page 23)
(Page 22)
(Page 22)
(Page 18)
(Page 22)
PRS-505
PRS-505
2727
TP413
R408
R477
R411
R416
IC402
TP412
TP407TP406
TP410TP409
TP415
TP405
TP401
TP400
TP403
R431
R425
IC403
Q402
IC405
IC408
Q403
Q406
R426
R424
C425
R402
R403
C402 C406 R421
IC409
R422
C424
C429
R415
C419
C420
IC406C422
R419
R420
C427
C449
R475
R418
C417C416
C413
C405
C403
R404
R405
R407R406
C430
R417
TP402 D420
TP404C401
D401
D403
R423
C404
C408
R427
R428 R429
R430
Q405
C407
C411 C412
R414
CN401
C426
C421
IC404
TP408
L402
L403
R413
PS401
TP411
IC407
R409
C418
C423
THP401
D402
Q401
Q472
IC401
470k
470k
0
470k
XC9226A296MR
VCORE
V2V2
UNREGUNREG
V3
BATT
GND
GND
DC
470k
10k
XC9226A196MR
RTQ035P02TR
XC61CN3002NR
XC61CC3202NR
2SA1832F-GR
HN1B04FE-Y/GR
10k
470k
0.1
100k
100k
10 10 2.2k
XC6213B312NR
0
0.1
1
47k
1
1
XC6215B292NR
0.1
100k
470k
0.1
0.1
22k
4.7k
1010
4.7
0.0015
10
47k
36k
10k6.8k
1
470k
DC CRS01(TE85R)
BATT10
DAN222-TL
DAN222-TL
100k
0.1
10
220
100k 2.2M
100k
2SC4738F-Y/GR
4.7
10 10
220k
2P
0.1
0.1
XC61CN2702NR
DCDET
220k
2A32V
V1
TC7WH74FK
0
0.1
0.1
UDZSNPTE-175.6B
2SC4738F-Y/GR
SSM3K03FE(TPL3)
SN412005RHLR(BQ24032)
LOW-BATT-LI
BATT-LI
PWRON
USBON
STAT2
STAT1
USB_VBUS
RESET
V3
ISET2
DC+
DC-
VCORE
V2
UNREG
V1
DCDET
GND
BATT-DC
UNREG
V2
GND
VCORE
CK
D Q GN
D
VC
C
PR
CL
R Q
GN
D
123
4 5 6
S
(10/10)
LITHIUM ION
BATTERY
3.7V 600mAh
CHARGECONTROL
B+ SWITCH
+2.9V REGULATOR
+1.9V REGULATOR
VOLTAGE DETECTOR
+2.9V REGULATOR
VOLTAGE DETECTOR VOLTAGE DETECTOR
+3.1V REGULATOR
INVERTER
BUFFER
INVERTER
RESET
Q402,405,406
6.8μH
6.8μH
6-15. SCHEMATIC DIAGRAM - MAIN Board (10/10) - • See page 29 for IC Block Diagram. • See page 34 for IC Pin Function Description.
MAIN BOARD IC201 R5C807 (MEMORY STICK DUO/SD MEMORY CARD CONTROLLER) Pin No. Pin Name I/O Description
1 VCCEN O +3.3V power supply control signal output terminal Not used2 GPIO I/O Not used3 LED O Not used
4 HWSPND I Hardware suspend mode select signal input from the main CPU "L": hardware suspend mode
5 RWMODE I Read-write timing mode select signal input terminal "H": maximum cycle time Fixed at "H" in this set
6 WAMODE I WAIT/DTACK mode select signal input terminal "L": DTACK mode, "H": WAIT mode Fixed at "L" in this set
7 LTLEN I Little/big endian select signal input terminal "L": little endian mode, "H": big endian mode Fixed at "L" in this set
8 TEST I Test mode terminal Normally fi xed at "L"9 CKIN I Host colck signal input from the main CPU10 GND - Ground terminal11 RST I Reset signal input terminal "L": reset12 VCC_ROUT - Power supply terminal (+1.8V)13 VCC_RIN - Power supply terminal (+1.8V)14 REGEN I Internal regulator control signal input terminal "L": regulator on Fixed at "H" in this set15 INT O Interrupt request signal output to the main CPU16 WAIT/DTACK O Data acknowledge signal output terminal Not used17 WR I Write enable signal input from the main CPU18 RD I Read enable signal input from the main CPU
19, 20 EB0, EB1 I Byte enable signal input terminal Not used21 VCC_HOST - Power supply terminal (+3.3V)22 CS I Chip select signal input from the address decoder
23 to 30 D15 to D8 I/O Two-way data bus with the USB controller, main CPU, SD-RAM and NOR fl ash memory
31 to 33 D7 to D5 I/O Two-way data bus with the USB controller, main CPU, NAND fl ash memory, SD-RAM and NOR fl ash memory
34 GND - Ground terminal
35 to 39 D0 to D4 I/O Two-way data bus with the USB controller, main CPU, NAND fl ash memory, SD-RAM and NOR fl ash memory
40 BS I Bus cycle start signal input terminal Not used41 A22 I Address signal input terminal Not used42 VCC_ROUT - Power supply terminal (+1.8V)
43 to 47 A21 to A17 I Address signal input terminal Not used48 VCC_HOST - Power supply terminal (+3.3V)49 A16 I Address signal input terminal Not used
50 to 64 A15 to A1 I Address signal input from the main CPU65 A0 I Address signal input terminal Not used66 GND - Ground terminal
67 SDCD I SD memory card detect signal input from the SD memory card slot "L": SD memory card slot in
68 SDDAT3 I/O Two-way 4-bits data bus with the SD memory card slot69 MDIO11 I/O Not used70 MSDAT0 I/O Two-way data bus with the memory stick duo slot71 MDIO12 I/O Not used72 MSDAT1 I/O Two-way data bus with the memory stick duo slot73 VCC_3V - Power supply terminal (+3.3V)74 MDIO13 I/O Not used75 MSDAT2 I/O Two-way data bus with the memory stick duo slot76 MDIO14 I/O Not used77 MSDAT3 I/O Two-way data bus with the memory stick duo slot
78 to 84 MDIO15, MDIO19 to MDIO24 I/O Not used
85 SDWP I SD memory card write protect switch signal input from the SD memory card slot86 VCC_ROUT - Power supply terminal (+1.8V)87 MSCLK O Serial clock signal output to the memory stick duo slot88 MDIO17 I/O Not used89 SDCLK O Serial clock signal output to the SD memory card slot
• IC Pin Function Description
PRS-505
35
Pin No. Pin Name I/O Description90 GND - Ground terminal
91, 92 SDDAT0, SDDAT1 I/O Two-way 4-bits data bus with the SD memory card slot93 MSBS O Bus state signal output to the memory stick duo slot94 SDDAT2 I/O Two-way 4-bits data bus with the SD memory card slot95 MDIO09 I/O Not used96 VCC_3V - Power supply terminal (+3.3V)97 SDCMD I/O Command signal input/output with the SD memory card slot98 MDIO27 I/O Not used
99 MSCD I Memory stick duo detect signal input from the memory stick duo slot "L": memory stick duo slot in
100 MDIO29 I/O Not used
PRS-505
36
MAIN BOARD IC301 A3P125-VQG100 (INDICATOR CONTROLLER) Pin No. Pin Name I/O Description
1 GND - Ground terminal2 to 8 PD15 to PD9 I Video data input from the main CPU
9 GND - Ground terminal10, 11 PD8, PD7 I Video data input from the main CPU
12 GND - Ground terminal13 PD6 I Video data input from the main CPU14 GND - Ground terminal
15, 16 PD5, PD4 I Video data input from the main CPU17 VCC - Power supply terminal (+1.5V)18 VCCI - Power supply terminal (+3.3V)
19 to 22 PD3 to PD0 I Video data input from the main CPU23 PSFL I Not used24 VMV - Power supply terminal (+3.3V)25 GND - Ground terminal26 FCLK I Frame clock signal input from the main CPU27 LCLK I Latch clock signal input from main CPU28 PCLK I Pixel clock signal input from the main CPU29 SDLE O Latch enable signal output to the ink indicator element
30 to 36 SDDO0 to SDDO6 O Video data input from the main CPU37 VCC - Power supply terminal (+1.5V)38 GND - Ground terminal39 VCC1 - Power supply terminal (+3.3V)40 SDDO7 O Video data input from the main CPU41 SDCLK O Clock signal output to the ink indicator element42 SDOE O Output enable signl output to the ink indicator element43 GDOE O Output enable signal output to the ink indicator element44 GDSP O Sharp panel signal output to the ink indicator element45 GDCLK O Clock signal output to the ink indicator element46 GND - Ground terminal47 TCK - Not used48 TDI - Not used49 TMS - Not used50 VMV - Power supply terminal (+3.3V)51 GND - Ground terminal52 VPUMP - Not used53 NC - Not used54 TDO - Not used55 TRST - Not used56 VJTAG - Not used
57 to 59 SDCE5 to SDCE3 O Chip enable signal output terminal Not used60 to 62 SDCE2 to SDCE0 O Chip enable signal output to the ink indicator element
63 SDSHR O Not used64 GDRL O Not used65 PWRCOM O Command signal output to the VCOM switch66 VCCI - Power supply terminal (+3.3V)67 GND - Ground terminal68 VCC - Power supply terminal (+1.5V)69 PWR2 O Power supply control signal output terminal70 BDR1 O Border control signal output terminal71 BDR0 O Border control signal output terminal72 PWR0 O Power supply control signal output terminal73 PWR1 O Power supply control signal output terminal74 VMV - Power supply terminal (+3.3V)75 GND - Ground terminal76 SPIDO O Not used77 SPICLK O Not used78 SPIDI I Not used79 SPICS O Not used
PRS-505
37
Pin No. Pin Name I/O Description80 I2CSCL O Not used81 I2CSDA I/O Not used82 PWR3 O Not used83 RESERVED - Not used
84 to 86 TEST2 to TEST0 I Ground terminal87 VCCIB - Power supply terminal (+3.3V)88 GND - Ground terminal89 VCC - Power supply terminal (+1.5V)
90 to 92 RESERVED - Not used93 PDOE I Output enable signal input from the main CPU94 RESET I Reset signal input from the main CPU95 RDY O Ready signal output to the main CPU96 STBY I Standby signal input from the main CPU97 ERR O Error signal output to the main CPU98 RESERVED - Not used99 GND - Ground terminal100 VMV - Power supply terminal (+3.3V)
PRS-505
38
MAIN BOARD IC401 SN412005RHLR (CHARGE CONTROL) Pin No. Pin Name I/O Description
1 LDO O Power supply (+3.3V) output terminal2 STAT1 O Charge state signal output to the sub CPU and LED drive signal for CHARGE indicator3 STAT2 O Charge state signal output to the sub CPU4 AC I Power supply input from the AC adaptor
5, 6 BAT I/O Power supply voltage input from the rechargeable battery or charge voltage output to the rechargeable battery
7 ISET2 I Charge current setting siganal input from the sub CPU "L": 100 mA, "H": 500 mA Fixed at "H" charging voltage in this set
8 PSEL I Charge source selection siganal input terminal "L": USB (pin 20), "H": AC (pin 4) Fixed at "H" charging voltage in this set
9 CE I Chip enable signal input terminal Not used10 ISET1 O Setting terminal for AC input charge current and AC precharge/termination11 VSS - Ground terminal12 TS I Thermal detection signal input terminal13 DPPM I Setting terminal for the dinamic power pass management
14 TMR I Timer program input terminal (Becomes impossible to do safety timer and charge termination when connecting LOD (pin 1))
15 to 17 OUT O Power supply voltage output terminal
18 XACPG O External DC power state detection signal output to the sub CPU "L": external DC power on
19 XUSBPG O USB power state detection signal output terminal Not used20 USB I Charge voltage input terminal from the USB connector21 GND - Ground terminal
PRS-505
39
MAIN BOARD IC801 HD64F38004FP10V-V198 (SUB CPU) Pin No. Pin Name I/O Description
1 BATT-DC I Power supply input from the AC adaptor2 X1 I System clock input terminal (32.768 kHz)3 X2 O System clock output terminal (32.768 kHz)4 VSS - Ground terminal5 OSC2 O System clock output terminal (4.9152 MHz)6 OSC1 I System clock input terminal (4.9152 MHz)7 TEST I Connect to ground8 XRESET I System reset signal input terminal "L": reset9 ISET1 I Charge current setting siganal input terminal
10 ISET2 O Charge current setting siganal output to the charge control11 to 13 P33 to P35 - Connect to power supply14, 15 STAT1, STAT2 I Charge state monitor input from the charge control
16 VCC - Power supply terminal (+2.9V)17 to 19 V1 to V3 - Connect to power supply
20 PWRON O Main power on/off control signal output terminal "H": main power on21 AD_ON O Rechargeable battery input control signal output terminal "H": rechargeable battery input22 POR O Power on reset signal output to the main CPU "H": reset23 XM_RESET O Master reset signal output to the main CPU "L": reset24 USBON O USB charge on/off control signal output terminal "H": USB charge on
25 to 29 KEY_OUT7 toKEY_OUT3 O Key scan signal output terminal Not used
30 to 32 KEY_OUT2 toKEY_OUT0 O Key scan signal output terminal
33 to 40 KEY_IN7 to KEY_IN0 I Key scan signal input terminal41 KEY-INT I Key scan interrupt input from the KEY-ON (pin 53)42 CTS I Clear to send signal input from the main CPU43 USBDET I USB cable connect signal input terminal "H": USB cable is connected44 LOW-BATT-LI I Rechargeable battery low detect signal input terminal45 WKP3 I Not used46 USBCHG I USB charge enable signal input from the main CPU
47 DCDET I External DC power state detection signal input from the charge control "L": external DC power on
48 STBY_SW I Power switch signal input terminal49 KEYLED O LED drive signal output terminal Not used50 LED_1 O LED drive signal output terminal for USB indicator "H": LED on51 LED_2 O LED drive signal output terminal Not used52 USBBOOT O Main CPU boot mode control signal output to the main CPU53 KEY-ON O Key scan interrupt signal output to the KEY-INT (pin 41)54 P95 O Connect to power supply55 VSS - Ground terminal56 IRQAEC I Not used57 RTS O Request to send signal output to the main CPU58 RXD I Serial data input from the main CPU59 TXD O Serial data output to the main CPU60 IRQ0 I Not used61 AVCC - Power supply terminal (+2.9V)62 AN0 I Not used63 BATT-LI I Rechargeable battery input terminal64 AN2 I Not used
PRS-505
40
MAIN BOARD IC1001 MC9328MXLVP20R2 (MAIN CPU) Pin No. Pin Name I/O Description
A1 AUDIO3_DATA O Serial data output to the audio D/A converterA2 SRAMINT I Not usedA3 VBUS I VBUS input from the USB connectorA4 XUSBD_OE O USB output enable signal output terminal Not usedA5 USBD_SUSPND O USB suspend signal output terminal Not usedA6 USB_VM I USB minus input terminal Not usedA7 USB20INT I Interrupt signal input from the USB controllerA8 SSI_TXCLK O Bit clock signal output to the audio D/A converterA9 NAND-CE1 O Chip enable signal output terminal Not used
A10 NAND-CE0 O Chip enable signal output to the NAND fl ash memoryA11 ERR O Error signal output to the indicator controllerA12 RDY I Ready signal input from the indicator controller
A13 to A15 PD2, PD4, PD5 O Video data output to the indicator controllerB1 AUDIO1_CS O Chip select signal output to the audio D/A conberterB2 AUDIO2_CLK O Clock signal output to the audio D/A conberter
B3 SD_DET I SD memory card detect signal input from the SD memory card slot "L": SD memory card slot in
B4 USBD_AFE O USB analog front end enable signal output terminal Not usedB5 USBD_RCV I USB serial data input terminal Not usedB6 USBD_VMO O USB minus output terminal Not usedB7 SSI_RXDAT I Serial data input terminal Not usedB8 UART1_TXD O Serial data output to the sub CPUB9 RY/#BY I Ready/busy select signal input from the NAND fl ash memory and NOR fl ash memoryB10 PCLK O Pixel clock signal output to the indicator controllerB11 STBY O Standby signal output to the indicator controller
B12 to B15 PD0, PD3, PD6, PD7 O Video data output to the indicator controllerC1 D31 I/O Two-way data bus with the SD-RAMC2 USBLED O LED drive signal output terminal for USB indicator "H": LED onC3 MSINT I Not usedC4 SD_WP I SD memory card write protect switch signal input from the SD memory card slotC5 PCAUDIO O Power supply on/off signal output terminal "H": power onC6 USBD_VPO O USB plus output terminal Not usedC7 UART2_RXD I Serial data input terminal Not usedC8 SSI_TXFS O L/R sampling clock signal output to the audio D/A converterC9 UART1_RTS I Request to send signal input from the sub CPUC10 SRA3P O Reset signal output to the indicator controllerC11 FCLK O Frame clock signal output to the indicator controller
C12 to C14 PD8, PD9, PD12 O Video data output to the indicator controller
C15 NVDD2 - Power supply terminal (+2.9V)D1 A23 O Address signal output to the address decoderD2 A24 O Address signal output terminal Not usedD3 PCR5CCLK O Host clock control signal output terminalD4 PB17 O Not usedD5 NVDD1 - Power supply terminal (+2.9V)D6 USBD_VP I USB plus input terminal Not usedD7 QVDD4 - Power supply terminal (+1.9V)D8 UART2_TXD O Serial data output terminal Not usedD9 NVDD3 - Power supply terminal (+2.9V)D10 NAND-ALE O Address latch enable signal output to the NAND fl ash mamoryD11 LCLK O Latch clock signal output to the indicator controller
D12, D13 PD1, PD11 O Video data output to the indicator controllerD14 HPSET I Not usedD15 PD13 O Video data output to the indicator controller
E1, E2 A21, A22 O Address signal output to the address decoderE3, E4 D30, D29 I/O Two-way data bus with the SD-RAM
E5 NVDD1 - Power supply terminal (+2.9V)E6 VSS - Ground terminalE7 PCSDCARD O Regulator control signal output terminal
PRS-505
41
Pin No. Pin Name I/O DescriptionE8 UART1_RXD I Serial data input from the sub CPUE9 UART1_CTS O Clear to send signal output to the sub CPUE10 NAND-CLE O Command latch enable signal output to the NAND fl ash mamoryE11 PDOE O Output enable signal output to the indicator controllerE12 PD10 O Video data output to the indicator controllerE13 TIN I Timer input terminal Not usedE14 PCA3PCORE O Regulator control signal output terminalE15 SRETHER O Not used
F1, F2 A20, A19 O Address signal output to the NOR fl ash memoryF3, F4 D28, D27 I/O Two-way data bus with the SD-RAMF5, F6 NVDD1 - Power supply terminal (+2.9V)
F7 PCMSCARD O Regulator control signal output terminalF8 SRUSB20 O No usedF9 SSI_TXDAT O Audio data output to the audio D/A converter
F10 SRSRAM1 O Not usedF11 QVDD3 - Power supply terminal (+1.9V)
F12, F13 PD14, PD15 O Video data output to the indicator controllerF14 USB_CHRG O USB charge enable signal output to the sub CPUF15 SRDSP O Reset signal output to the audio D/A converter
G1, G2 A17, A18 O Address signal output to the NOR fl ash memoryG3, G4 D26, D25 I/O Two-way data bus with the SD-RAM
G5 NVDD1 - Power supply terminal (+2.9V)G6 VSS - Ground terminalG7 NVDD4 - Power supply terminal (+2.9V)
G8 to G10 VSS - Ground terminalG11 PCA3PIO O Regulator control signal output terminalG12 PCUSB11 O Not usedG13 RSCINT I Interrupt request signal input from the memory stick duo/SD memory card controller
G14 MSDET I Memory stick duo detect signal input from the memory stick duo slot "L": memory stick duo slot in
G15 SRMS O Not used
H1 A15 O Address signal output to the memory stick duo/SD memory card controller, SD-RAM and NOR fl ash memory
H2 A16 O Address signal output to the NOR fl ash memoryH3 to H5 D22 to D24 I/O Two-way data bus with the SD-RAMH6 to H9 VSS - Ground terminal
H10 NVDD2 - Power supply terminal (+2.9V)H11 USB_BOOT I Main CPU boot mode control signal input from the sub CPU
H12 PCR5C O Hardware suspend mode output to the memory stick duo/SD memory card controller "L": hardware suspend mode
H13 PA14 O Not usedH14 I2CSDA I/O Two-way IIC bus with the temperature sensorH15 TMS I Test mode select signal input terminal Not used
J1, J2 A14, A12 O Address signal output to the memory stick duo/SD memory card controller, SD-RAM and NOR fl ash memory
J3, J4 D21, D20 I/O Two-way data bus with the SD-RAMJ5 NVDD1 - Power supply terminal (+2.9V)
J6, J7 VSS - Ground terminalJ8 QVDD1 - Power supply terminal (+1.9V)J9 VSS - Ground terminalJ10 SRR5C O Reset signal output to the memory stick duo/SD memory card controllerJ11 I2CSCL O IIC bus serial clock signal output to the temperature sensorJ12 TCK I Test clock signal input terminal Not usedJ13 XTDO O Test data signal output terminal Not used
J14, J15 BOOT1, BOOT0 I System boot mode select signal input terminal
K1 A13 O Address signal output to the memory stick duo/SD memory card controller, SD-RAM and NOR fl ash memory
K2 A11 O Address signal output to the memory stick duo/SD memory card controller and NOR fl ash memory
K3 XCS2 O Chip select signal output to the SD-RAMK4 D19 I/O Two-way data bus with the SD-RAM
PRS-505
42
Pin No. Pin Name I/O DescriptionK5 NVDD1 - Power supply terminal (+2.9V)
K10 D1 I/O Two-way data bus with the memory stick duo/SD memory card controller, USB controller, NAND fl ash memory, SD-RAM and NOR fl ash memory
K11 BOOT2 I System boot mode select signal input terminalK12 TDI I Test data input terminal Not usedK13 BIG_ENDIAN I Not used
K14 XRESET-OUT O Reset signal output to the audio D/A converter, memory stick duo/SD memory card control-ler, USB controller, NAND fl ash memory and NOR fl ash memory
K15 XTAL32K O System clock output terminal (32.768 kHz)
L1, L2 A10, A9 O Address signal output to the memory stick duo/SD memory card controller, SD-RAM and NOR fl ash memory
L3, L4 D17, D18 I/O Two-way data bus with the SD-RAML5, L6 NVDD1 - Power supply terminal (+2.9V)
L7 XCS5 O Chip select signal output terminal
L8 D2 I/O Two-way data bus with the memory stick duo/SD memory card controller, USB controller, NAND fl ash memory, SD-RAM and NOR fl ash memory
L9 PA20 O Not usedL10, L11 VSS - Ground terminal
L12 POR I Power on reset signal input from the sub CPU "H": resetL13 VSS - Ground terminalL14 XTAL16M O System clock output terminal Not usedL15 EXTAL32K I System clock input terminal (32.768 kHz)M1 D16 I/O Two-way data bus with the SD-RAM
M2 to M4 D15, D13, D10 I/O Two-way data bus with the memory stick duo/SD memory card controller, USB controller, SD-RAM and NOR fl ash memory
M5 XEB3 O Byte strobe signal output terminal Not usedM6 NVDD1 - Power supply terminal (+2.9V)
M7, M8 XCS4, XCS1 O Chip select signal output terminalM9 PA18 - Not usedM10 XRW O Read/write enable signal output terminalM11 VSS - Ground terminalM12 BOOT3 I System boot mode select signal input terminalM13 QVDD2 - Power supply terminal (+1.9V)M14 XRESET-IN I Master reset signal input from the sub CPU "L": resetM15 EXTAL16M I System clock input terminal Not used
N1, N2 A8, A7 O Address signal output to the memory stick duo/SD memory card controller, USB controller, SD-RAM and NOR fl ash memory
N3 D12 I/O Two-way data bus with the memory stick duo/SD memory card controller, USB controller, SD-RAM and NOR fl ash memory
N4 XEB0 O Byte strobe signal output terminal Not used
N5, N6 D9, D8 I/O Two-way data bus with the memory stick duo/SD memory card controller, USB controller, SD-RAM and NOR fl ash memory
N7, N8 XCS3, XCS0 O Chip select signal output terminalN9 PA17 - Not used
N10 D0 I/O Two-way data bus with the memory stick duo/SD memory card controller, USB controller, NAND fl ash memory, SD-RAM and NOR fl ash memory
N11, N12 DQM2,DQM0 O Data enable signal output to the SD-RAMN13 SDCK0 O Clock enable signal output to the SD-RAMN14 TRISTATE I Not usedN15 XTRST I Test reset signal input terminal Not used
P1 D14 I/O Two-way data bus with the memory stick duo/SD memory card controller, USB controller, SD-RAM and NOR fl ash memory
P2 A1 O Address signal output to the memory stick duo/SD memory card controller, USB controller and NOR fl ash memory
P3 to P6 A2 to A5 O Address signal output to the memory stick duo/SD memory card controller, USB controller, SD-RAM and NOR fl ash memory
P7, P8 D6, D5 I/O Two-way data bus with the memory stick duo/SD memory card controller, USB controller, NAND fl ash memory, SD-RAM and NOR fl ash memory
P9, P10 MA10, MA11 O Address signal output to the SD-RAM
PRS-505
43
Pin No. Pin Name I/O DescriptionP11 DQM1 O Data enable signal output to the SD-RAMP12 XRAS O Row address select signal output to the SD-RAMP13 SDCKE1 O Clock enable signal output to the SD-RAM Not usedP14 CLKO O Host clock signal output to the memory stick duo/SD memory card controllerP15 XRESET-SF O Not used
R1 A6 O Address signal output to the memory stick duo/SD memory card controller, USB controller, SD-RAM and NOR fl ash memory
R2 D11 I/O Two-way data bus with the memory stick duo/SD memory card controller, USB controller, SD-RAM and NOR fl ash memory
R3 XEB1 O Byte strobe signal output terminal Not used
R4 XEB2 O Write enable signal output to the memory stick duo/SD memory card controller, USB controller and NOR fl ash memory
R5 XOE O Read enable signal output terminal
R6 D7 I/O Two-way data bus with the memory stick duo/SD memory card controller, USB controller, NAND fl ash memory, SD-RAM and NOR fl ash memory
R7 A0 O Address signal output terminal Not usedR8 SDCLK O Clock output to the SD-RAM
R9 D4 I/O Two-way data bus with the memory stick duo/SD memory card controller, USB controller, NAND fl ash memory, SD-RAM and NOR fl ash memory
R10 GPSRAM1 O Not used
R11 D3 I/O Two-way data bus with the memory stick duo/SD memory card controller, USB controller, NAND fl ash memory, SD-RAM and NOR fl ash memory
R12 DQM3 O Data enable signal output to the SD-RAMR13 XCAS O Column address select signal output to the SD-RAMR14 XSDWE O Write enable signal output to the SD-RAMR15 AVDD1 - Power supply terminal (+2.9V)
IC101 6-702-290-01 IC AK4365VN-L IC107 6-706-492-01 IC TC7SHU04FU (T5RSOJF) IC108 6-706-487-01 IC TC7SH08FU (T5RSOYJF) IC201 6-709-523-01 IC R5C807 IC202 6-706-487-01 IC TC7SH08FU (T5RSOYJF)
IC203 6-711-467-01 IC TC74LCX138FK (EL, K) IC204 6-708-467-01 IC XC6213B312NR IC205 6-708-467-01 IC XC6213B312NR IC206 8-759-592-49 IC TC7SZ125FU (TE85R) IC301 (Not supplied) IC A3P125-VQG100
IC302 6-711-802-01 IC XC6215B152NR IC303 6-708-472-01 IC XC6215B312NR IC401 6-708-160-01 IC SN412005RHLR IC402 6-709-526-01 IC XC9226A296MR
IC403 6-711-801-01 IC XC9226A196MR
IC404 6-702-148-01 IC XC61CN2702NR IC405 8-759-824-57 IC XC61CN3002NR IC406 6-709-520-01 IC XC6215B292NR IC407 8-759-698-31 IC TC7WH74FK (TE85R) IC408 6-709-522-01 IC XC61CC3202NR
IC409 6-708-467-01 IC XC6213B312NR IC801 6-807-759-01 IC HD64F38004FP10V-V198 IC802 6-705-886-01 IC XC61CN2502NR IC953 (Not supplied) IC S1R72V17B00A20B@ IC1001 6-705-206-01 IC MC9328MXLVP20R2
IC1002 6-706-815-01 IC TMP75AIDR IC1101 6-705-485-01 IC TC7MP245FK (EL) IC1102 6-705-485-01 IC TC7MP245FK (EL) IC1106 (Not supplied) IC K9F2G08U0A-PCBOT IC1107 6-711-803-01 IC TC7MP01FK
IC1108 6-600-060-01 IC TC7WZ32FK (TE85R) IC1112 8-759-679-53 IC SN74LVC244APWR IC1113 8-759-679-53 IC SN74LVC244APWR IC1116 8-759-592-49 IC TC7SZ125FU (TE85R) IC1117 8-759-592-49 IC TC7SZ125FU (TE85R)
IC1201 (Not supplied) IC K4M561633G-BN75T IC1202 (Not supplied) IC K4M561633G-BN75T IC1203 (Not supplied) IC S29AL016D90TFI020H-PRS02 IC1802 6-705-480-01 IC LT3467ES6#TR IC1803 8-759-337-40 IC NJM2904V (TE2)
IC1805 6-705-481-01 IC LT1931ES5#TR IC1806 8-759-675-54 IC TC7W53FK (TE85R) IC1807 8-759-337-40 IC NJM2904V (TE2)
R365 1-218-990-81 SHORT CHIP 0 R376 1-218-990-81 SHORT CHIP 0 R377 1-218-990-81 SHORT CHIP 0 R378 1-218-990-81 SHORT CHIP 0 R379 1-218-990-81 SHORT CHIP 0
R380 1-218-990-81 SHORT CHIP 0 R381 1-218-990-81 SHORT CHIP 0 R382 1-218-990-81 SHORT CHIP 0 R383 1-218-990-81 SHORT CHIP 0 R384 1-218-990-81 SHORT CHIP 0
SUPPLEMENT-1File this supplement with the service manual.
Subject: Change of MAIN board (Suffi x-12)
In this set, MAIN board has been changed in the midway of production. Printed wiring board, schamatic diagram and electrical parts list of new type are described in this supplement-1. Refer to original service manual for other information.
1. NEW/FORMER DISCRIMINATION ................. 1
2. DIAGRAMS2-1. Printed Wiring Board - MAIN Board (Component Side) - ................................ 32-2. Printed Wiring Board - MAIN Board (Conductor Side) - .................................. 42-3. Schematic Diagram - MAIN Board (1/10) - ................... 52-4. Schematic Diagram - MAIN Board (2/10) - ................... 62-5. Schematic Diagram - MAIN Board (3/10) - ................... 72-6. Schematic Diagram - MAIN Board (4/10) - ................... 82-7. Schematic Diagram - MAIN Board (5/10) - ................... 92-8. Schematic Diagram - MAIN Board (6/10) - ................... 102-9. Schematic Diagram - MAIN Board (7/10) - ................... 112-10. Schematic Diagram - MAIN Board (8/10) - ................... 122-11. Schematic Diagram - MAIN Board (9/10) - ................... 132-12. Schematic Diagram - MAIN Board (10/10) - ................. 14
3. ELECTRICAL PARTS LIST .............................. 15
TABLE OF CONTENTS
1. NEW/FORMER DISCRIMINATIONPRS-505US Model
Canadian ModelFormer : 1-875-228-11New : 1-875-228-12
– MAIN Board (Component Side) –
PRS-505
PRS-505
22
2. DIAGRAMS
For Schematic Diagrams.Note:• All capacitors are in μF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics
and tantalums.• All resistors are in Ω and 1/4 W or less unless otherwise
specifi ed.• f : internal component.• C : panel designation.
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note is printed in each block.)
• A : B+ Line.• B : B– Line.• C : adjustment for repair.• Power voltage is dc 5.2V and fed with regulated dc power
supply from TP402 and TP400 on the MAIN board.• Voltages are dc with respect to ground under no-signal
(detuned) conditions. no mark : POWER ON ( ) : AUDIO PLAY * : Impossible to measure (For this model, the voltage is produced only when the
screen is changed. Under the power on, there is a voltage that is not produced.)
• Voltages are taken with VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production
tolerances.• Signal path. F : AUDIO L : VIDEO N : USB O : SD MEMORY CARD/MEMORY STICK DUO
For Printed Wiring Boards.Note:• Y : Parts extracted from the conductor side.• f : internal component.• : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.)
Caution:Parts face side:(Conductor side)Pattern face side: (Component side)
Parts on the parts face side seen from the pattern face are indicated.Parts on the pattern face side seen from the parts face are indicated.
Note: The components identi-fi ed by mark 0 or dotted line with mark 0 are criti-cal for safety. Replace only with part number specifi ed.
Note: Les composants identifi és par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le nu-méro spécifi é.
• MAIN board is multi-layer printed board. However, the patterns of intermediate-layers have not been in-
cluded in diagrams.
• Lead layoutssurface
CSP (Chip Size Package) Lead layout of conventional IC
* Replacing of IC1001 on the MAIN board used in this set requires a special tool.
• The voltage and waveform of CSP (chip size package) cannot be measured, because its lead is different feom that conventional IC.
* Replacing of IC1001 on the MAIN board used in this set requires a special tool.
Note: When IC301, IC953, IC1106, IC1201, IC1202 and IC1203 on the MAIN board is damaged, exchange the new MAIN board for the MAIN board which IC damaged.
IC101 6-702-290-01 IC AK4365VN-L IC107 6-706-492-01 IC TC7SHU04FU (T5RSOJF) IC108 6-706-487-01 IC TC7SH08FU (T5RSOYJF) IC201 6-709-523-01 IC R5C807 IC202 6-706-487-01 IC TC7SH08FU (T5RSOYJF)
IC203 6-711-467-01 IC TC74LCX138FK (EL, K) IC204 6-708-467-01 IC XC6213B312NR IC205 6-708-467-01 IC XC6213B312NR IC206 8-759-592-49 IC TC7SZ125FU (TE85R) IC301 (Not supplied) IC A3P125-VQG100
IC302 6-711-802-01 IC XC6215B152NR IC303 6-708-472-01 IC XC6215B312NR IC401 6-708-160-01 IC SN412005RHLR IC402 6-709-526-01 IC XC9226A296MR IC403 6-711-801-01 IC XC9226A196MR
IC404 6-702-148-01 IC XC61CN2702NR IC405 8-759-824-57 IC XC61CN3002NR IC406 6-709-520-01 IC XC6215B292NR IC407 8-759-698-31 IC TC7WH74FK (TE85R) IC408 6-709-522-01 IC XC61CC3202NR
IC409 6-708-467-01 IC XC6213B312NR IC801 6-807-759-01 IC HD64F38004FP10V-V198 IC802 6-705-886-01 IC XC61CN2502NR IC953 (Not supplied) IC S1R72V17B00A20B@ IC1001 6-705-206-01 IC MC9328MXLVP20R2
IC1002 6-706-815-01 IC TMP75AIDR IC1101 6-705-485-01 IC TC7MP245FK (EL) IC1102 6-705-485-01 IC TC7MP245FK (EL) IC1106 (Not supplied) IC K9F2G08U0A-PCBOT IC1107 6-711-803-01 IC TC7MP01FK
IC1108 6-600-060-01 IC TC7WZ32FK (TE85R) IC1112 8-759-679-53 IC SN74LVC244APWR IC1113 8-759-679-53 IC SN74LVC244APWR IC1116 8-759-592-49 IC TC7SZ125FU (TE85R) IC1117 8-759-592-49 IC TC7SZ125FU (TE85R)
IC1201 (Not supplied) IC K4M561633G-BN75T IC1202 (Not supplied) IC K4M561633G-BN75T IC1203 (Not supplied) IC S29AL016D90TFI020H-PRS02 IC1802 6-705-480-01 IC LT3467ES6#TR IC1803 8-759-337-40 IC NJM2904V (TE2)
IC1805 6-705-481-01 IC LT1931ES5#TR IC1806 8-759-675-54 IC TC7W53FK (TE85R) IC1807 8-759-337-40 IC NJM2904V (TE2)
R355 1-218-990-81 SHORT CHIP 0 R364 1-218-953-11 RES-CHIP 1K 5% 1/16W R365 1-218-990-81 SHORT CHIP 0 R376 1-218-990-81 SHORT CHIP 0 R377 1-218-990-81 SHORT CHIP 0
R378 1-218-990-81 SHORT CHIP 0 R379 1-218-990-81 SHORT CHIP 0 R380 1-218-990-81 SHORT CHIP 0 R381 1-218-990-81 SHORT CHIP 0 R382 1-218-990-81 SHORT CHIP 0
R383 1-218-990-81 SHORT CHIP 0 R384 1-218-990-81 SHORT CHIP 0 R385 1-218-990-81 SHORT CHIP 0 R386 1-218-990-81 SHORT CHIP 0 R387 1-218-953-11 RES-CHIP 1K 5% 1/16W
Checking the version allows you to jump to the revised page.Also, clicking the version at the top of the revised page allows you to jump to the next revised page.
Ver. Date Description of Revision1.0 2007.09 New
1.1 2007.12 Change of Part No. for INK (INDICATION) ELEMENT ASSY
Change of MAIN board (Suffi x-12) (SUPPLEMENT-1) (ECN-ECC50062/ECC52854)