PLA001mb - PureLogic · 2019. 3. 20. · 04. MACH3 installation for module operation 05. Terms of Warranty INSTRUCTION MANUAL 2 3 4 4 7 PLA001mb Controlled relay block for Mach3 (MODBUS

01. Introduction, general information 02. Technical specifications03. Module connection04. MACH3 installation for module operation05. Terms of Warranty

INSTRUCTION MANUAL23447

PLA001mbControlled relay block for Mach3(MODBUS through COM-port, 8 relays)

PLA001mb. Controlled relay block for Mach3 (MODBUS through COM-port, 8 relays)

Edition from 22.11.2017 3www.purelogic.ru8 (800) 555 63 74

01 Introduction, general information

Technical specifications

It is a well-known fact that when building CNC machines with apply of PC and MACH3 program, a common problem occurs with existence of necessary number of free inputs/outputs for limit sensors, buttons and external load connection. The problem caused in the first place by the fact that PC LPT-port (the port through which MACH3 operates the machine) has only 12 output lines and 5 input lines which is not enough for building a full-featured CNC machine. To solve the problem you can connect extenders of input/output lines to the system which collaborates with MACH3 through COM-port (or USB port using COM>USB adapter) under protocol MODBUS. MACH3 supports MODBUS devices.

PLA001mb is output lines expander, 8 independent relays controlled from MACH3 through COM-port (or USB-port using COM>USB adapter) under protocol MODBUS.

PLA002mb is input lines expander, 8 independent optoisolated inputsare registered by MACH3 through COM-port (or USB-port using COM>USB adapter) under protocol MODBUS.

TURN OFF POWER DEVICE BEFORE MAKING ANY CONNECTIONS or module mode changing POWER SUPPLY NEGATIVE WIRE CONNECTION WITH GROUND (GND), IS FORBIDDEN

Supply voltageMax consumption current СОМ-port settings Isolation resistanceRelay characteristics Operating temperature Module dimensions Net weight

12V DC or 9V AC 300 mА38`400, 8 bit, 1stop-bit, Parity-Even500 MOhm7А./220V0 ... 60 °С75x72 mm0,2 kg

02

01. Introduction, general information

Fig.1. Module connection, settings



03

04

Module connection

MACH3 installation for module operation

03. Module connection

Press ‘Apply’ button, then ‘OK’. Be sure to restart MACH3.In the ‘Settings’ window of Function Cfg`s/Setup Serial Modbus Control it is necessary to perform support setting of module PLA001mb, set the parameters as it is shown below:

Now it is necessary to correlate output signals of MACH3 with relay K1...K8 on PLA001mb board. MODBUS port in MACH3 is “0” port. Relay “K1” is “Pin #7” …Relay “K8” is “Pin #0”.Example of signal setting Output#1 = K8 … Output#1 = K1 is shown below:

Connection of module PLA001mb is performed according to fig.1Module PLA001mb is connected to COM-port of PC through a standard connector DB-9 XP11 or through COM>USB adapter (it is purchased separately, not included in the set). Module PLA001mb has inbuilt rectifier of alternating voltage therefore as a power source you can use direct current source 12V or alternate current – 9V.The voltage is connected to XP9 or XP10, polarity of connection is not important.We recommend to use 12V source of the PC as a voltage source.Power loads are connected to XP1...XP8, relay action K1...K8 is indicated by HL1...HL8 LEDs.

Start MACH3. In the “Settings” window of Config/Ports and Pins turn on ModBus InputOutput Support, according to the figure:



04. MACH3 installation for module operation

When changing Active Low state with help of a mouse for set Output #1 … Output #8, you can be sure of the set device operation.

The warranty period is 12 months after purchasing and is valid only if all operational conditions and scheduled maintenance are strictly followed.

1. General terms1.1. In case of product acquisition as separate components, Seller guarantees working ability of every component, but does not assume responsibility for the quality of their joint work (mismatch of components). If you have questions please consult our technical support team.1.2. Seller does not guarantee compatibility of the purchased product with the one that Buyer already has or bought from third parties.1.3. Product’s component parts and configuration can be changed by manufacturer without notice due to the product consistent technical improvement.

2. Conditions for warranty acceptance2.1. The product is accepted only in the same completeness of set as it was purchased.

3. Warranty service procedure3.1. Warranty service is performed by testing the claimed product defect. 3.2. If the defect is proved, warranty repair is carried out.

4. We do not assume any responsibility for glass, electric lamps, starters and expendable materials as well as:4.1. Damaged product caused by inappropriate transport and store conditions, wrong connection, operation in abnormal (off-design) mode, or in conditions which are not manufacturer-supplied (including temperature and humidity out of limits of recommended range), having damages due to third-party circumstances (voltage jumps, natural disasters, etc.), also having mechanical or thermal damages.

Terms of Warranty 05



4.2. The product with traces of foreign objects or substances impact, including dust, liquids, insects, also objects having extraneous inscription. 4.3. The product with traces of unauthorized tampering and (or) repair process (traces of opening, home-made soldering, elements changing etc).4.4. The product with self-diagnostic function that shows improper exploitation.4.5. Technically complex product in respect of which assembly and integration and start-up works were not performed by Seller specialists or by recommended organizations, except in cases directly regulated under goods documentation. 4.6. In cases when the product exploitation was performed in conditions when power supply did not correspond with manufacturer’s requirements, also when there is no electrical protection device .4.7. The product which was resold by the initial buyer to the third party.4.8. The product with defects which were caused by low-quality spare parts or fulfilled their service life spare parts,consumable materials, also using spare parts, consumable materials not corresponding with manufacturer’s requirements.

Produced and accepted in accordance with obligatory requirements of valid technical documentation and is qualified for exploitation.

Lot number:Technical Control Department

05. Terms of Warranty

We draw your attention to the fact that there can be some changes in this instruction due to the product consistent technical improvement. You can always download our latest versions at www.purelogic.ru

www.purelogic.ru

ContactsMoscow +7 (495) 505-63-74Voronezh +7 (473) 204-51-56

149 Office160, Leninsky avenue, Voronezh, Russia, 394033

Monday - Thursday: 8.00–17:00Friday: 8.00–16.00Break: 12.30–13.30

[email protected]

PLA001mb - PureLogic · 2019. 3. 20. · 04. MACH3 installation for module operation 05. Terms of Warranty INSTRUCTION MANUAL 2 3 4 4 7 PLA001mb Controlled relay block for Mach3 (MODBUS

Documents