PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS SERVICE INC. P.O.Box 1760, Long Beach, CA 90801-1760 U.S.A. PIONEER EUROPE NV Haven 1087 Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE.LTD. 253 Alexandra Road, #04-01, Singapore 159936 C PIONEER CORPORATION 2000 K-ZZA. OCT. 2000 Printed in Japan ORDER NO. CRT2558 HIGH POWER CD PLAYER WITH RDS TUNER DEH-1330R X1M/EW Service Manual CONTENTS 1. SAFETY INFORMATION ............................................3 2. EXPLODED VIEWS AND PARTS LIST .......................4 3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ...12 4. PCB CONNECTION DIAGRAM ................................34 5. ELECTRICAL PARTS LIST ........................................42 6. ADJUSTMENT..........................................................48 7. GENERAL INFORMATION .......................................52 7.1 DIAGNOSIS ........................................................52 7.1.1 TEST MODE ..............................................52 7.1.2 DISASSEMBLY .........................................55 7.1.3 CONNECTOR FUNCTION DESCRIPTION .......59 7.2 PARTS .................................................................60 7.2.1 IC................................................................60 7.2.2 DISPLAY ....................................................66 7.3 OPERATIONAL FLOW CHART ...........................68 8. OPERATIONS AND SPECIFICATIONS.....................69 DEH-1300R X1M/EW DEH-1310 X1M/EE DEH-1330R/X1M/EW - This service manual should be used together with the following manual(s): Model No. Order No. Mech. Module Remarks CX-958 CRT2423 S8.1 CD Mech. Module:Circuit Description, Mech.Description, Disassembly
75
Embed
Pioneer DEH 1330R,DeH 1300R,DeH 1310 Service Manual
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS SERVICE INC. P.O.Box 1760, Long Beach, CA 90801-1760 U.S.A.PIONEER EUROPE NV Haven 1087 Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE.LTD. 253 Alexandra Road, #04-01, Singapore 159936
C PIONEER CORPORATION 2000 K-ZZA. OCT. 2000 Printed in Japan
ORDER NO.
CRT2558
HIGH POWER CD PLAYER WITH RDS TUNER
DEH-1330R X1M/EW
ServiceManual
CONTENTS
1. SAFETY INFORMATION ............................................3
2. EXPLODED VIEWS AND PARTS LIST .......................4
8. OPERATIONS AND SPECIFICATIONS.....................69
DEH-1300R X1M/EW
DEH-1310 X1M/EE
DEH-1330R/X1M/EW
- This service manual should be used together with the following manual(s):Model No. Order No. Mech. Module Remarks
CX-958 CRT2423 S8.1 CD Mech. Module:Circuit Description, Mech.Description, Disassembly
2
DEH-1330R,1300R,1310
- CD Player Service Precautions
1. For pickup unit(CXX1285) handling, please refer
to"Disassembly"(see page 55).
During replacement, handling precautions shall be
taken to prevent an electrostatic discharge(protection
by a short pin).
2. During disassembly, be sure to turn the power off
since an internal IC might be destroyed when a con-
nector is plugged or unplugged.
3. Please checking the grating after changing the ser-
vice pickup unit(see page 50).
3
DEH-1330R,1300R,1310
1. SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repaircomplex products such as those covered by this manual.Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.If you are not qualified to perform the repair of this product properly and safely; you should not risk trying to do soand refer the repair to a qualified service technician.
1. Safety Precautions for those who Service this Unit.
• When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable
results.
Caution:
1. During repair or tests, minimum distance of 13cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.
2. A “CLASS 1 LASER PRODUCT” label is affixed to the
bottom of the player.
3. The triangular label is attached to the mechanism
unit frame.
4. Specifications of Laser Diode
Specifications of laser radiation fields to which human access is possible during service.Wavelength = 800 nanometers
CLASS 1LASER PRODUCT
4
DEH-1330R,1300R,1310
1 Cord Assy See Contrast table(2)2 Screw CBA10023 Handle CNC53954 Bush CNV3930
* 5 Polyethylene Bag E36-615
6 Polyethylene Bag CEG-1627-1 •••••7-2 Owner's Manual See Contrast table(2)7-3 Owner's Manual See Contrast table(2)7-4 Installation Manual See Contrast table(2)
* 7-5 Passport See Contrast table(2)* 7-6 Warranty Card CRY1157
8 Carton See Contrast table(2)9 Contain Box See Contrast table(2)
10 Protector CHP2346
11 Protector CHP234712 Case Assy CXB3520
Mark No. Description Part No. Mark No. Description Part No.
(1) PACKING SECTION PARTS LIST
NOTE:
- Parts marked by “*” are generally unavailable because they are not in our Master Spare Parts List.
- Screws adjacent to ∇ mark on the product are used for disassembly.
2. EXPLODED VIEWS AND PARTS LIST
2.1 PACKING
10
1
12
6
8
9
11
7
4
3
5
2
5
DEH-1330R,1300R,1310
Part No.Mark No. Symbol and Description DEH-1330R/X1M/EW DEH-1300R/X1M/EW DEH-1310/X1M/EE
86 Photo-transistor(Q1, 2) CPT230SX-TU87 Damper CNV617588 Rack CNV601489 Spring CBH2315
- CD MECHANISM MODULE SECTION PARTS LIST
12
DEH-1330R,1300R,13101 2 3 4
1 2 3 4
D
C
B
A
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM
3.1 BLOCK DIAGRAM
M
M
M
LDMD
HOLOGRAMUNIT
FOCUS ACTTRACKING ACT
LD+
MD
FO+
TO+
14
5
4
3
SPINDLEMOTOR
CARRIAGEMOTOR
LOADINGMOTOR
1
2
3
4
3
1
2
SELECTSENSE
DISC SENSE
D
CN801
CN802
D802 D801
VD
S802CLAMP
6
5
11
22
23
21
1
28
21
CDLOAD
CDEJET
CONT
EJTSNS
DSCSNS
CLAMP
CD5VON
VDCONT
VDD IC 701BA05SFP
IN
+5V REGULATOR
24
1
VD
Q981
Q982
B.U
ANTENNA CN402
A
LOCL
Q411
VCC VDD
PC
E2
PC
K
PC
E1
SL
SD
PD
IO
C
Q101CN101
FOP
TOP
A+C/F
B+D/E
98LD L_OUT
PD
HOME
97
24
23
39
X201
TD/FD
SD/MD
RF-AMP, DSP,SERVO, DAC
IC 201UPD63711GC
16CN701 CN605
17
1
8
24
CDL
IC 301BA5985FM
S801HOME12
16
18
11
14
13
10
9
SOP
TOP
FOP
SOM
COP
COM
LOP
LOM
FWD
REV
MUTE
CD
DR
IVE
R
7 18
19
20
14
3
2
4
CLAMP
DINC
EJTD
CDLOAD
EJET
CONT
PDIO
TUNER AMP UNIT
CONTROL UNITPICKUP UNIT(SERVICE)(P8)
PHOTO UNIT(S8)
4
VD
CD5VON
IC 3EEPROM
FM/AM TUNER UNIT
28
27
FM/AM 1ST IF 10.7MHzT51 Q51 CF51 CF52 CF53
IC1MIXER, IF AMP, DET.
6
21
18LDET
COMP
2225 10 14 12 15 16 8 13 2 3 4
CF202
VDDVCC
DI/D
O
CE
2
CK
CE
1
SD
BW
SL
FMS
D
NL1
NL2
IC 2 FM MPX
AMANT
FMANT
ATT
ATT
AMRF
FMRF
IMG ADJ
RF ADJ
X90110.25MHz
ANT ADJ
LOCL23
LOCH
AMDETMPXREF 41kHz
AM 2ND IF450kHz
19
CR
EQ
11
DG
ND
1
ST
IND
L ch
5R ch
924
NC
FMLO
CL
20177
NC
NC
WC
26 RFGND
Q472 Q475 Q476
RDSDECODER
IC 701PM4009A
20
11 12
X702
Q477
VDD
TMUTE
FM/AM
LDET
13
DEH-1330R,1300R,13105 6 7 8
5 6 7 8
D
C
B
A
KYDT
DPDT
KEY CONT. LCD DRIVER
IC 1801PD6340A
3
4
5
3
4
5
KEY MATRIX
SD
SL
PCE
PCK
TUNPCE2
PDO
LOCL
IN2_L
IN3_L
6
76
14
13
48
12
57
2
3
SYSTEMCONTROLLER
IC 601(1/2)PE5195A
VSTVCKVDT
B.UVDD
Q903B.U
BACKUP
FL—
FL+
RL—
RL+
ACC
2
1
9
11
10
12
4
E.VOLFIE/EQ
IC 301PML003AM
SYSTEMCONTROLLER
IC 601(2/2)PE5195A
ASENS63
BSENS64
CELLMUTE32
SYSPW42
MUTE44
KYDT8
DPDT9
RESET60
SWVDD41
Frontout_L10
Rearout_L11
POWER AMP
IC 302TDA7386
14
12
22 4
5
3
21
23
FL
MUTE STBY
RL
B.Ubsens
asens
Q902Q351 MUTEQ350
B KEYBOARD UNIT
CN1801CN601
LCD
22 23
X1801
20
18
Q650
RESETIC 602
S—80834ANY VDD1 2
SY
SP
W
GND
B.U
SYSPW
5B.REM
FUSE10A
CD5VON
31
34
23
80
79
27
22
35
VDCONT
CLAMP
DSCSNS
EJTSNS
CDLOAD
CDEJET
CONT
PDI11PDIO
VST/ VCK/ VDT
Q901
VDD
VDD
VLCD
56
10
CN901
IC970TPD1018F
POWER SWITCH
5
6
1
Q346
CN301
REAR L CH
Q363
RR+
RR-
FR+
FR-
FL+
FL-
RL+
RL-ACCGND
BACKUP
BACK UP
FL–
FL+
RL–
RL+
B.REM
ACC
GND
B.REM
CELLULARMUTE
7TELIN
Q951
CELLULAR MUTE
TELIN
66
61
21FM/AM
LDET
TMUTE
14
DEH-1330R,1300R,13101 2 3 4
1 2 3 4
D
C
B
A
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)(DEH-1330R/X1M/EW, DEH-1300R/X1M/EW)Note: When ordering service parts, be sure to refer to “EXPLODED VIEWS AND PARTS LIST” or “ELECTRICAL PARTS
LIST”.
A-a A-b
A-aA-a A-b A-b
A-b A-b A-a A-a
Large sizeSCH diagram
Guide page
Detailed page
A
DS
P-2
01M
-S00
B
123
272
272
123
162
162
473
4.194MHz
PE5195A
CN601
CN403
CN402
FM(100%):-15.5dBsAM(30%):-26dBs
SYSTEM CONTROLLER
For resistors and capacitors in the circuit diagrams, their resistance values orcapacitance values are expressed in codes:
*Capacitors Code Practical value 103 0.01µF 101/10 100µF/10V
The > mark found on some component parts indicatesthe importance of the safety factor of the part.Therefore, when replacing, be sure to use parts ofidentical designation.
Symbol indicates a resistor.No differentiation is made between chip resistors anddiscrete resistors.
NOTE :
Symbol indicates a capacitor.No differentiation is made between chip capacitors anddiscrete capacitors.
*Capacitors Code Practical value 103 0.01µF 101/10 100µF/10V
The > mark found on some component parts indicatesthe importance of the safety factor of the part.Therefore, when replacing, be sure to use parts ofidentical designation.
Symbol indicates a resistor.No differentiation is made between chip resistors anddiscrete resistors.
NOTE :
Symbol indicates a capacitor.No differentiation is made between chip capacitors anddiscrete capacitors.
Pickup Unit(Service)(P8) CXX1285M 1 Motor Unit(CARRIAGE) CXB2190M 2 Motor Unit(LOADING) CXB2195M 3 Motor Unit(SPINDLE) CXB2562
Fuse(10A) CEK1136
=====Circuit Symbol and No.===Part Name Part No.--- ------ ------------------------------------------ -------------------------
=====Circuit Symbol and No.===Part Name Part No.--- ------ ------------------------------------------ -------------------------
C
D
48
DEH-1330R,1300R,1310
1) Precautions• This unit uses a single power supply (+5V) for the reg-
ulator. The signal reference potential, therefore, isconnected to REFO(approx. 2.5V) instead of GND.If REFO and GND are connected to each other by mis-take during adjustments, not only will it be impossi-ble to measure the potential correctly, but the servowill malfunction and a severe shock will be applied tothe pick-up. To avoid this, take special note of the fol-lowing.Do not connect the negative probe of the measuringequipment to REFO and GND together. It is especiallyimportant not to connect the channel 1 negativeprobe of the oscilloscope to REFO with the channel 2negative probe connected to GND.Since the frame of the measuring instrument is usual-ly at the same potential as the negative probe, changethe frame of the measuring instrument to floating sta-tus.If by accident REFO comes in contact with GND,immediately switch the regulator or power OFF.
• Always make sure the regulator is OFF when connect-ing and disconnecting the various filters and wiringrequired for measurements.
• Before proceeding to further adjustments and mea-surements after switching regulator ON, let the playerrun for about one minute to allow the circuits to stabi-lize.
• Since the protective systems in the unit's software arerendered inoperative in test mode, be very careful toavoid mechanical and /or electrical shocks to the sys-tem when making adjustment.
• Disc detection during loading and eject operations isperformed by means of a photo transistor in thisunit.Consequently, if the inside of the unit is exposedto a strong light source when the outer casing isremoved for repairs or adjustment, the following mal-functions may occur.
*During PLAY, even if the eject button ispressed,the disc will not be ejected and the unitwill remain in the PLAY mode.
*The unit will not load a disc.When the unit malfunctions this way, either re-posi-tion the light source, move the unit or cover the phototransistor.
2) Test ModeThis mode is used for adjusting the CD mechanismmodule of the device.
• Test mode starting procedureReset while pressing the 4 and 6 keys together.
• Test mode cancellationSwitch ACC, back-up OFF.
• After pressing the EJECT key, do not press any otherkey until the disk is completely ejected.
• If the ] or [ key is pressed while focus search is inprogress, immediately turn the power off (otherwisethe actuator may be damaged due to adhesion of thelenses).
• Jump operation of TRs other than 100TR continuesafter releasing the key. CRG move and 100TR jumpoperations are brought into the “Tracking close” sta-tus when the key is released.
• Powering Off/On resets the jump mode to “1TR”, andthe automatic adjustment value to the initial value.
6. ADJUSTMENT
6.1 CD ADJUSTMENT
49
DEH-1330R,1300R,1310
- Flow Chart
4
3
Reset
SOURCE
New test mode
6
[
BAND
BAND
BAND
BAND
BAND
3
*2*1
6
6
6
6
1
2
1
2]
] [
Select CD
Focus ModeSelect
Focus Close/S Curve Check
CRG- Auto AdjustmentDisplay Select
<Tracking Servo Close> CRG+
RF AGC Coefficient Display/Rough Servo and RF AGC
Tracking Open
TrackingOpen
T. Close andFit Servo
] [
1
3
Display
2
3
Displayor
8x 8x 8xTRK SECMIN
9x 9x 9xTRK SECMIN
or
CRG-CRG+ T.BalanceAdjustment
*4F, T, RF AGC/F.Bias Display Select
F, T AGC andRF AGC
Power ON(Adjustment for T.Offset)
*5 *6 *6
*7CRG/TR Jump NO.Select
CRG+/TR Jump+
CRG-/TR Jump-
Power OFF
Display
Display
Display
T.Close andF,T AGC andRF AGC andFit Servo
Power ON(Not adjustment for T.Offset)
Display
Display
2
Power OFF
Power OFF
Power OFF 8x 8x 8xTRK SECMIN
9x 9x 9xTRK SECMIN
8x 8x 8xTRK SECMIN
9x 9x 9xTRK SECMIN
or
8x 8x 8xTRK SECMIN
9x 9x 9xTRK SECMIN
or
00 00 00TRK SECMIN
99 99 99TRK SECMIN
or
00 00 00TRK SECMIN
99 99 99TRK SECMIN
or
00 00 00TRK SECMIN
99 99 99TRK SECMIN
or
91 91 91TRK SECMIN
0x 0x 0xTRK SECMIN
00 00 00TRK SECMIN
99 99 99TRK SECMIN
Test Mode In
*3
*1
*3
*6
*2
*5
*7
*4
F.Cancel T.Offset The original display
1TR/4TR/10TR/32TR/100TR"00", "99"→Focus Close / "01"→S.Curve
1TR 4TR91(81) 92(82)
CRG Move96(86)
100TR95(85)
32TR94(84)
10TR93(83)
Focus Close00(99)
LD Off02
S.Curve01
CRG Move,100TR Jump
TRK, MIN, SEC F.AGC Gain T.AGC Gain F.Bias
50
DEH-1330R,1300R,1310
• Note :The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mecha-nism module is adjusted on the production line to match the CD mechanism module and is thus the best adjustedPU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, ifthe PU unit must be changed, the grating should be checked using the procedure below.
• Purpose :To check that the grating is within an acceptable range when the PU unit is changed.
• Symptoms of Mal-adjustment :If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to performtrack search operations, or taking a long time for track searching.
• Method :
• Measuring Equipment • Oscilloscope, Two L.P.F.• Measuring Points • E, F, REFOUT• Disc • ABEX TCD-784• Mode • TEST MODE
• Checking Procedure1. In test mode, load the disc and switch the 5V regulator on.2. Using the ] and [ buttons, move the PU unit to the innermost track.3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjust-
ment the display should now read "81". Press key 3 2 times. The display will change, returning to "81" on thefourth press.
4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase differ-ence is within 75° . Refer to the photographs supplied to determine the phase angle.
5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is anyimprovement. If, after trying this a number of times, the grating angle does not become less than 75° then themechanism should be judged to be at fault.
• NoteBecause of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may beseen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the aver-age angle.
• HintReloading the disc changes the clamp position and may decrease the "wobble".
F
REFO
E
100kΩ
390pF
100kΩ
390pF
E
REFO
F
REFO
L.P.F.
L.P.F.
CONTROL UNIT
Xch Ych
Oscilloscope
6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT
If an error such as off focus, spindle unlocking, unreadable sub-code, or sound skipping occurs after setup, its
cause and time occurred (in absolute time) are displayed.
During setup, operational status of the control software (internal RAM: CPOINT) is displayed.
These displays and functions are prepared for enhancing aging in the servicing and efficiency of trouble analysis.
(1) Shifting to the New Test Mode
1 Turn on the current test mode by starting the reset from the key.
2 Select S-CD for the source through the specified procedure including use of the [SOURCE] key, and inserting the
disc. Then, press the [Jump Mode Selector] key while maintaining the regulator turned off.
3 After the above operations, the new test mode remains on irrespective of whether the S-CD is turned on or off.
You can reset the new test mode by turning on the reset start.
* With some products, the new test mode can be reset through the same operations as that employed for shifting to
the STBY mode (while maintaining the Acc turned off).
(2) Key Correspondence
Key Test mode New test mode
(Example) Power Off Power On In-play Error Production
BAND To power on To power off – Time/Err.No. switching
(offset adjustment performed)
] – FWD-Kick FF/TR+ –
[ – REV-Kick REV/TR- –
1 – T.Close (AGC performed) Scan –
/parameter display switching
2 – T.BAL adjustment Mode –
/T.Open
3 To power on F.Close/RF AGC/AGC – –
(offset adjustment not performed)
6 – Mode switching Auto/Manu –
/T.Close (no AGC)/Jump switching
Note: Eject and CD on/off is performed in the same procedure as that for the normal mode.
(3) Cause of Error and Error Code
Code Class Contents Description and cause
40 Electricity Off focus detected. FOK goes low.
→ Damages/stains on disc, vibrations or failure on servo.
41 Electricity Spindle unlocked. FOK = Low continued for 50 msec.
→ Damages/stains on disc, vibrations or failure on servo.
42 Electricity Sub-code unreadable. Sub-code was unreadable for 50 msec.
→ Damages/stains on disc, vibrations or failure on servo.
43 Electricity Sound skipping detected. Last address memory function was activated.
→ Damages/stains on disc, vibrations or failure on servo.
Note: Mechanical errors during aging are not displayed.
The error codes should be indicated in the same way as in the normal mode.
54
DEH-1330R,1300R,1310
(4) Display of Operational Status (CPOINT) during SetupStatus No. Contents Protective action01 Carriage move to home position started. None02 Carriage is moving toward inner diameter. Specified 10 seconds has been passed or failure
on home switch.03 Carriage is moving toward outer diameter. Specified 10 seconds has been passed or failure
on home switch.05 Carriage outer diameter feed (1 second) in progress. None11 Setup started. None12 Spindle rotation and focus search started. None13 Waiting for focus close (XSI=Low). Specified focus search time has been passed.14 Waiting for focus close (FOK=High). (After AGC) Specified focus search time has been passed.15 Waiting for focus close (FOK=High). (Before AGC) Specified focus search time has been passed.16 Rough AGC in progress. Off focus.17 Setup (1/2) before T balance adjustment is started. Off focus.18 Setup (2/2) before T balance adjustment is started. Off focus.24 T balance adjustment (1/2). Off focus.25 T balance adjustment (2/2). Off focus.26 Standing by after spindle rough servo is over. Off focus.27 Setup before RF AGC (first) is started. Off focus.28 RF AGC (first) in progress. Off focus.29 Setup before RF AGC (second) is started. Off focus.30 RF AGC (second) in progress. Off focus.31 Tracking close in progress. Off focus.32 Standing by after tracking is closed. Off focus.33 Focus AGC started. Off focus.34 Focus AGC in progress. Tracking AGC started. Off focus.35 Tracking AGC in progress. Off focus.
Spindle processes applicable servo.36 Check of MIRR and LOCK pin. RF AGC in progress. Off focus. Spindle not locked.
CRG close in progress. Check of sub-code. Sub-code unreadable.
(5) Display Examples
1) During Setup (When status no. = 11)
TRK No. MIN. SEC.
11 11' 11"
2) During Operation (TOC read, TRK search, Play, FF and REV)
The same as in the normal mode.
3) When a Protection Error Occurred
Switch to the following displays (A) and (B) using the [BAND] switch:
(A) Error occurrence timing display in absolute time.
An example: Error occurred in 12th tune at 34'56" in absolute time.
TRK No. MIN. SEC.
12 34' 56"
(B) Error No. display
An example: Error #40 (Off focus is detected)
ERROR-40
55
DEH-1330R,1300R,1310
- Removing the Tuner Amp Unit
Remove the three screws and then remove
the Cover. (Fig.2)
Remove the two screws. (Fig.2)
Remove the screw. (Fig.3)
Straight the tabs at fore locations indicated
and then remove the Tuner Amp Unit.
(Fig.3)
- Removing the Case Unit (not shown)
1. Remove the Case Unit.
- Removing the CD Mechanism Module (Fig.1)
Remove the four screws.
Disconnect the connector and then remove the CD
Mechanism Module (not shown).
- Removing the Panel Assy (not shown)
1.Disconnect the two stoppers and then remove the
Panel Assy.
Fig.1
Fig.2
Fig.3Tuner Amp Unit
Cover
CD Mechanism Module
7.1.2 DISASSEMBLY
56
DEH-1330R,1300R,1310
- Removing the Upper Frame
1. Remove six Springs A, two Springs B and four
Screws.
2. Remove two Tabs situated on rear side of the Upper
Frame, remove two Arms on the front side, then
remove two Tabs on the front side.
- Removing the Carriage Mechanism
1. Disengage the Carriage Mechanism from the two
dampers situated in the front side by driving it up,
then disengage and remove the mechanism from the
one damper by driving it up aslant into front side
direction.
Note : When assembling the Carriage Mechanism, coat
the dampers with alcohol prior to the assembly.
- Removing the Clamp Arm Assy
1. Remove a Spring A, a B and a Spring C.
2. Drive the Clamp Arm Assy up into rear side direction,
then disengage the arm from its current position
Finally, drive the assembly approximately 45 degrees
upward, then slide the assembly toward right side to
remove it.
B
A
B A
A
A
Arm
Arm
A
B
C
Upper Frame
Carriage Mechanism Section
Clamp Arm Assy Section
A
A
57
DEH-1330R,1300R,1310
- Removing the Guide Arm Assy
1. Remove a connector, a spring A and B
2. Drive the Guide Arm Assy up aslant into rear side
direction, then remove it from a Pin. Finally, drive the
assembly approximately 45 degrees upward, then
slide the assembly toward left side to remove it.
Note : When assembling the guide arm assembly, route
the cord inside the assembly. In this operation,
care must be exercised so that cord may be
caught by the gear.
- Removing the LO Arm Assy
1. Remove two Pins to dismount the LO Arm Assy.
- Removing the Control Unit and the Spindle
Motor
1. Remove from the connector after mounting the short
pin on the flexible PCB of the pickup unit.
2. Remove two Soldered joints, then remove two
Screws A.
3. Remove two connectors and a Screw B.
4. Disengage the Control Unit from two Tabs, then dis-
mount the unit by sliding it toward left.
5. Dismount the Spindle Motor.
A
Guide Arm Assy Section
B
Pin
LO Arm Assy Section
Spindle Motor
A A
Control Unit
Short Pin
B
58
DEH-1330R,1300R,1310
- Removing the Loading Motor and Carriage
Motor
1. Remove the Spring and two Screws A.
2. Dismount the Loading Motor.
3. Remove the Belt, a Screw B, two Screws C, a Guide
and a Screw Unit.
4. Dismount the Carriage Motor.
Note : When assembling the Belt, use care so that it
may not be contaminated by grease.
- Removing the Pickup Unit
1. Remove two Screws and a Shaft.
2. Dismount the Pickup Unit.
Pickup Unit
Shaft
CGuide
B
Screw Unit Carriage Motor
AA
CBelt
Loading Motor
59
DEH-1330R,1300R,1310
7.1.3 CONNECTOR FUNCTION DESCRIPTION
579 13
468 210121416
111315
1. BACK UP 2. GND 3. NC 4. ACC 5. B.REM 6. NC 7. TEL MUTE 8. NC 9. FL-10. RL-11. FL+12. RL+13. FR-14. RR-15. FR+16. RR+
PRE OUT ANTENNA
60
DEH-1330R,1300R,1310
7.2 PARTS
7.2.1 IC
- Pin Functions(PE5195A, PE5196A)Pin No. Pin Name I/O Format Function and Operation
1 MODEL1 I Model select input2 NL1 I Noise level input3 NL2DT I Noise level input 24 AVSS AVSS5 ST I Stereo input6 SD I SD signal input 7 AREF1 AVREF18 KYDT I Key data input9 DPDT O C Key data output
10 SDBW I SDBW input11 TUNPDI I PLL IC data input12 TUNPDO O C PLL IC data output13 TUNPCK O C PLL IC clock output14 TUNPCE O C PLL IC chip enable output15 currq O C Tuner voltage FIX output16 XSI I C CD LSI serial data input(TSI)17 XSO O C CD LSI serial data output(TSO)18 XSCK O C CD LSI serial clock output(TSCK)19 drst O C RDS decoder reset output20 ADPW O C A/D converter power output21 fm/AM O C Tuner power supply control output22 VDCONT O C VD power supply control output23 CONT O C Servo driver power control output24 XAO O C CD LSI command / data control output25 xrst O C CD LSI reset control output26 xstb O C CD LSI strobe output27 CLAMP I Disc clamp sense input28 MIRR I Mirror detection input 29 FOK I Focus OK signal input30 LOCK I Spindle lock detector input31 CDLOAD O LOAD motor loading control output32 TELIN I Cellular mute input33 VSS VSS34 CDEJECT O LOAD motor eject control output35 CD5VON O C CD +5V power supply control output
36–39 NC Not used40 RECIEVE O C RDS decoder receiving output41 swvdd O C Grille microcomputer power supply control output42 SYSPW O C System power supply control output43 ILMPW O C Illumination power output44 mute O C Mute output45 PEE O C Beep tone output46 LOCH O C LOCH output47 RDS57K I 57kHzBP-OUT sense input48 TUNPCE2 O C EEPROM chip enable output49 PCL O C Test mode clock adjustment output50 VCK O C Clock output for electronic volume51 VDT O C Data output for electronic volume52 ANTPW O Antenna power output53 VST O Strobe pulse output for electronic volume54 DALMON O Stand-by output
55,56 NC Not used57 LOCL O LOCL output58 rdslk I RDSLK input
61
DEH-1330R,1300R,1310
Pin No. Pin Name I/O Format Function and Operation59 RDT I RDS data input60 reset Reset61 LDET I PLL lock detection input62 RCK I RDS clock input63 asens I ACC power sense input64 bsens I Back up power sense input65 dsens I Grille detach sense input66 TMUTE O C Tuner mute output67 NC Not used68 VDD VDD69 X2 Crystal oscillator connection pin70 X1 Crystal oscillator connection pin71 IC(VPP) IC(VPP)72 NC Not used73 TESTIN I Test program mode input74 AVDD AVDD75 AVREF0 AVREF076 SL I Signal level input77 TEMP I Temperature detection input78 VDSENS I VD power supply sense input79 DINC I Disc detection input80 EJTD I Disc eject position detect input
801
20
21 40
41
60
61
*PE5195A, PE5196A
Output Format MeaningC C MOS output
IC's marked by* are MOS type.
Be careful in handing them because they are very liable
to be damaged by electrostatic induction.
S-80834ANY
1 2 31
OUT VDD VSS
62
DEH-1330R,1300R,1310
- Pin Functions (PD6340A)Pin No. Pin Name I/O Function and Operation
1-5 SEG4-0 O LCD segment output6-9 COM3-0 O LCD common output 10 VLCD LCD drive power supply
11-14 KST3-0 O Key strobe output15,16 KDT0,1 I Key data input (analogue input)
17 REM I Remote control reception18 DPDT I Display data input19 NC Not used20 KYDT O Key data output21 MODA GND22 X0 Crystal oscillator connection pin23 X1 Crystal oscillator connection pin24 VSS GND
25,26 KDT2,3 I Key data input27 NC Not used28 KST4 O Key strobe output
29-32 NC Not used33-55 SEG35-13 O LCD segment output
56 VDD Power supply57-64 SEG12-5 O LCD segment output
*PD6340A
49
4833
32
17
16 1
64
63
DEH-1330R,1300R,1310
- Pin Functions (UPD63711GC)Pin No. Pin Name I/O Function and Operation
1 D.GND Logic circuit GND2 RFOK O RFOK signal output3 rst I Reset signal input4 A0 I Command/parameter identification signal input5 stb I Data strobe signal input6 sck I Clock signal input for serial data input/output7 SO O Serial data and status signal output8 SI I Serial data input9 xtalen I Crystal oscillation control pin
10 D.VDD Positive power supply terminal to logic circuit11 DA.VDD Positive power supply terminal to D/A converter12 R_OUT O Right channel audio output signal13 DA.GND D/A converter GND14 REGC I The outside putting capacitor connection pin for SCF regulator15 DA.GND D/A converter GND16 L_OUT O Left channel audio output signal17 DA.VDD Positive power supply terminal to D/A converter18 R+ O Right channel audio data output19 R- O Right channel audio data output20 L- O Left channel audio data output21 L+ O Left channel audio data output22 X.VDD Positive power supply terminal to crystal oscillation circuit23 XTAL I Crystal oscillator connect pin24 xtal O Crystal oscillator connect pin25 X.GND Crystal oscillation circuit GND26 D.VDD Positive power supply terminal to logic circuit27 EMPH O Output pin for the pre-emphasis data in the sub-Q code28 FLAG O Flag output pin to indicate that audio data currently being output consists
of noncorrectable data29 DIN I Serial data input to internal DAC30 DOUT O Serial audio data output31 SCKIN I Serial clock input to internal DAC32 SCKO O Audio data that is output from DOUT changes at rising edge of this clock33 LRCKIN I LRCK signal input to internal DAC34 LRCK O Signals to distinguish the right and left channels of the audio data output
from DOUT35 HOLD O Defect detection output36 TX O Digital audio interface data output37 D.GND Logic circuit GND38 C16M O Oscillator clock buffering output39 LIMIT I Status of the pin is output at Bit 5 of the status output40 D.VDD Positive power supply terminal to logic circuit41 LOCK O EFM synchronous detection signal42 RFCK O Frame synchronous signal of XTAL-system43 MIRR O MIRR output44 PLCK O Monitor pin of bit clock45 D.GND Logic circuit GND46 C1D1 O Output pin for indicating the C1 error correction results47 C1D2 O Output pin for indicating the C1 error correction results48 C2D1 O Output pin for indicating the C2 error correction results49 C2D2 O Output pin for indicating the C2 error correction results50 C2D3 O Output pin for indicating the C2 error correction results51 D.VDD Positive power supply terminal to logic circuit52 PACK O CD-TEXT PACK synchronous signal53 TSO O CD-TEXT data serial output54 TSI I CD-TEXT control parameter serial input55 tsck I CD-TEXT serial clock input56 TSTB I CD-TEXT parameter strobe signal input57 D.GND Logic circuit GND
64
DEH-1330R,1300R,1310
Pin No. Pin Name I/O Function and Operation58 TEST0 I Test pin59 TEST1 I Test pin60 ATEST O Test pin61 A.GND Analog circuit GND62 FD O Focus drive output63 TD O Tracking drive output64 SD O Sled drive output65 MD O Spindle drive output66 DAC0 O DAC output for adjustment67 DAC1 O DAC output for adjustment68 DAC2 O DAC output for adjustment69 DAC3 O DAC output for adjustment70 A.VDD Positive power supply terminal to analog circuit71 EFM O EFM signal output72 ASY I EFM comparator reference voltage input73 C3T 3T detection capacitor additional pin74 RFI I RF signal input for EFM data regulation75 AGCO O RF signal output of after gain adjustment 76 AGCI I RF-AGC amplifier input77 RFO O RF summing amplifier output78 EQ2 RF amplifier equalizer parts additional pin79 EQ1 RF amplifier equalizer parts additional pin80 RF- I RF summing amplifier inverted input81 A.GND Analog circuit GND82 A I Photo detector A input83 C I Photo detector C input84 B I Photo detector B input85 D I Photo detector D input86 F I Photo detector F input87 E I Photo detector E input88 A.VDD Positive power supply terminal to analog circuit89 REFOUT O Reference electric potential output90 FE- I Focus error amplifier inverted input91 FEO O Focus error amplifier output92 TE- I Tracking error amplifier inverted input93 TEO O Tracking error amplifier output94 TE2 O Tracking error output of after amplification95 TEC I Tracking comparator input96 A.GND Analog circuit GND97 PD I PD detection signal input for LD output monitor 98 LD O LD control current output99 PN I APC circuit control polarity set pin
100 A.VDD Positive power supply terminal to analog circuit
20
21
40
41 60
61
80
1
100
76
26
125
7551
50
*UPD63711GC
65
DEH-1330R,1300R,1310
No. Symbol I/O Explain1 STIND O stereo "Low" when the FM stereo signals are received.
indicator To be pulled up to the "VDD" at 47kΩ.2 FMSD O FM station "High" when signals are received. To be pulled up to the "VDD" at 47kΩ
detector Meanwhile, 10kΩ should be used when taking diver FIX trigger from hereand "High: 0.9VDD or more" and "Low: 250mV or less".(Should satisfy the diver IC specifications)
3 NL1 O noise level-1 "High" when noise is received. Output for the RDS. GND at 47kΩ //1,800pF.4 NL2 O noise level-2 "High" when noise is received. Output for the RDS. GND at 36kΩ //330pF.5 Rch O R channel FM stereo "R-ch" signal output or AM audio output.
output Add the specified di-emphasis constant. 6 Lch O L channel FM stereo "L-ch" signal output or AM audio output.
output Add the specified di-emphasis constant. 7 WC write control EEPROM write control. Writing permissible at "Low". Normally open. 8 SDBW O SD bandwidth SD bandwidth signal output. For detection of detuning data for the RDS.9 NC Not used
10 VDD power Power supply pin for the digital section.supply D.C. 5V +/- 0.25V. Be careful about overlapping noise in the logic section.
11 DGND digital ground Grounding for the digital section. 12 CE2 I chip enable-2 EEPROM chip enable. Active a "Low"
To be pulled up to the "VDD" at 47kΩ13 SL I/O signal level Received FM/AM signal level (strength) output.
Connect the specified load resistor and capacitor (10k Ω + 39k Ω //4,700pF) 14 DI/DO I/O data input/ Data input/Data output
data output To be pulled up to the "VDD" at 47kΩ15 CK I clock Clock input To be pulled up to the "VDD" at 47kΩ16 CE1 I chip enable-1 AF·RF chip enable. Active at "High" To be grounded at 47kΩ17 NC Not used18 LDET O lock detector Active at "Low". To be pulled up to the "VDD" at 47kΩ19 CREQ I current request Active at "Low". To be grounded at 47kΩ20 NC Not used21 COMP O composite signal FM composite signal output. r out < 100Ω22 VCC power supply Analog section power supply pin.D.C.8.4V +/- 0.3V 23 LOCH I local high FM local high pin. When seeking local high, apply 5V together with "LOCL". 24 FMLOCL I FM local low FM local low pin. When seeking local low, apply 5V to the base of the NPN
transistor with which the specified resistor is being connected to the emitter. Keep it open in case of ordinary marketed models.
25 LOCL I local low FM/AM local low pin. When seeking local low, apply 5V to the base of the NPN transistor. Since this pin is exclusive for AM when the FMLOCL is in use,do not drive it under FM.
26 RFGND RF ground Grounding for the antenna section. 27 FMANT I FM antenna input FM antenna input. 75Ω. Serge absorber (DSP-201M-S00B) is necessary. 28 AMANT I AM antenna input AM antenna input. High impedance.
Connect to the antenna through an L (LAU type) of 4.7µH.To cope with thepower transmission line hums, insert a series circuit consisting of an L(a coil of about 100mH) + R (a resistor of 470 Ω to 2.2kΩ) between the GND.
IC 3EEPROM
FM/AM TUNER UNIT
28
27
FM/AM 1ST IF 10.7MHzT51 Q51 CF51 CF52 CF53
IC1MIXER, IF AMP, DET.
6
21
18LDET
COMP
2225 10 14 12 15 16 8 13 2 3 4
CF202
VDDVCC
DI/D
O
CE
2
CK
CE
1
SD
BW
SL
FMS
D
NL1
NL2
IC 2 FM MPX
AMANT
FMANT
ATT
ATT
AMRF
FMRF
IMG ADJ
RF ADJ
X90110.25MHz
ANT ADJ
LOCL23
LOCH
AMDETMPXREF 41kHz
AM 2ND IF450kHz
19
CR
EQ
11
DG
ND
1
ST
IND
L ch
5R ch
924
NC
FMLO
CL
20177N
C
NC
WC
26 RFGND
66
DEH-1330R,1300R,1310
SEG37
SEG35
SEG34
SEG33
SEG32
SEG31
SEG30
SEG29
SEG28
SEG27
SEG26
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
NC
NC
SEG19
SEG36
COM2B
COM0A
COM2C
COM3B
COM2D
COM1B
COM0B
SEG39
SEG38
COM3A
COM2A
COM1A
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
21
1
47
46
45
44
43
42
41
39
38
50
49
48
40
COM2B
COM0A
COM2C
COM3B
COM2D
COM1B
COM0B
COM3A
COM2A
COM1A
SE
GM
EN
T
CO
MM
ON
7.2.2 DISPLAY
- CAW1632(DEH-1330R/X1M/EW, DEH-1300R/X1M/EW)
67
DEH-1330R,1300R,1310
SEG37
SEG35
SEG34
SEG33
SEG32
SEG31
SEG30
SEG29
SEG28
SEG27
SEG26
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
NC
NC
SEG19
SEG36
COM2B
COM0A
COM2C
COM3B
COM2D
COM1B
COM0B
SEG39
SEG38
COM3A
COM2A
COM1A
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
21
1
47
46
45
44
43
42
41
39
38
50
49
48
40
COM2B
COM0A
COM2C
COM3B
COM2D
COM1B
COM0B
COM3A
COM2A
COM1A
SE
GM
EN
T
CO
MM
ON
- CAW1633(DEH-1310/X1M/EE)
68
DEH-1330R,1300R,1310
7.3 OPERATIONAL FLOW CHART
VDD=5V68pin
Power ON
BSENS=L
ASENS=L
DSENS=L
bsens64pin
asens63pin
dsens65pin
ADPW←H20pin
SWVDD←L41pin
Source keys operative
Completes power-on operation.(After that, proceed to each source operation.)
SYSPW←H42pin
Starts communication with Grille microcomputer.
Source ON
300ms
300ms
In case of the above signal, the communication with Grille microcomputer may fail.If the time interval is not 300msec, the oscillator may be defective.
69
DEH-1330R,1300R,1310
Buttons 1–6
EJECT buttonCD loading slot
AUDIO button
5/∞/2/3 buttons
SOURCE button
+/– buttons
BAND button
LOCAL/BSM button
Detach button
EQ button
LOUD button
CLOCK button
8. OPERATIONS AND SPECIFICATIONS
8.1 OPERATIONS
Key Finder
Buttons 1–6
EJECT buttonCD loading slot
AUDIO button
5/∞/2/3 buttons
SOURCE button
+/– buttons
BAND button
LOCAL/BSM button
Detach button
EQ button
TA button
PTY button
Head Unit (DEH-1330R,1300R)
Head Unit (DEH-1310)
70
DEH-1330R,1300R,1310
Bas
ic O
pera
tion
Bas
ic O
pera
tion
of T
uner
Pres
et T
unin
g
•Y
ou c
an m
emor
ize
broa
dcas
t st
atio
ns in
but
tons
1th
roug
h 6
for
easy
, one
-tou
ch s
tati
on r
ecal
l.
Pres
et s
tatio
n re
call
2 se
cond
s or
less
Bro
adca
st s
tatio
n pr
eset
mem
ory
2 se
cond
s or
mor
e
Not
e:•
Up
to 1
2 FM
sta
tions
(6
in F
1 (F
M1)
and
F2
(FM
2))
and
6 M
W/L
W
stat
ions
can
be
stor
ed in
mem
ory.
•Y
ou c
an a
lso
use
the
5or
∞bu
ttons
to r
ecal
l bro
adca
st s
tatio
nsm
emor
ized
in b
utto
ns 1
thro
ugh
6.
Pres
et N
umbe
r Ind
icat
orB
and
Indi
cato
rFreq
uenc
y In
dica
tor
Thi
s pr
oduc
t’s A
F fu
nctio
n ca
n be
sw
itche
d O
N a
nd O
FF. A
F sh
ould
be
switc
hed
OFF
for
norm
al tu
ning
ope
ratio
ns.
To L
iste
n to
Mus
icT
he f
ollo
win
g ex
plai
ns th
e in
itial
ope
ratio
ns r
equi
red
befo
re y
ou c
an li
sten
to m
usic
.
Not
e:•
Loa
ding
a d
isc
in th
is p
rodu
ct.
1.Se
lect
the
des
ired
sou
rce
(e.g
. Tun
er).
Eac
h pr
ess
of th
e SO
UR
CE
but
ton
sele
cts
the
desi
red
sour
ce in
the
follo
win
g or
der:
Bui
lt-in
CD
pla
yer
=T
uner
Not
e:•
Whe
n no
dis
c is
set
in th
is p
rodu
ct, b
uilt-
in C
D p
laye
r so
urce
will
not
cha
nge.
•W
hen
this
pro
duct
’s b
lue/
whi
te le
ad is
con
nect
ed to
the
car’
s A
uto-
ante
nna
rela
y co
ntro
l ter
min
al,
the
car’
s A
uto-
ante
nna
exte
nds
whe
n th
is p
rodu
ct’s
sou
rce
is s
witc
hed
ON
. To
retr
act t
he a
nten
na,
switc
h th
e so
urce
OFF
.
2.R
aise
or
low
er t
he v
olum
e.
3.Tu
rn t
he s
ourc
e O
FF.
Hol
d fo
r 1
seco
nd
Eac
h pr
ess
chan
ges
the
Sour
ce ..
.
Man
ual a
nd S
eek
Tuni
ng
•Y
ou c
an s
elec
t th
e tu
ning
met
hod
by c
hang
ing
the
leng
th o
f ti
me
you
pres
s th
e 2
/3bu
tton
.
Man
ual T
unin
g (s
tep
by s
tep)
0.5
seco
nds
or le
ss
Seek
Tun
ing
0.5
seco
nds
or m
ore
Not
e:•
If y
ou c
ontin
ue p
ress
ing
the
butto
n fo
r lo
nger
than
0.5
sec
onds
, you
can
ski
p br
oadc
ast
stat
ions
. See
k T
unin
g st
arts
as
soon
as
you
rele
ase
the
butto
n.•
Ster
eo in
dica
tor
“”
light
s w
hen
a st
ereo
sta
tion
is s
elec
ted.
Ban
d F1 (
FM1)
=
F2 (
FM2)
=
MW
/LW
71
DEH-1330R,1300R,1310
Bas
ic O
pera
tion
Bas
ic O
pera
tion
of B
uilt-
in C
D P
laye
r
Trac
k N
umbe
r Ind
icat
orPl
ay T
ime
Indi
cato
r
CD L
oadi
ng S
lot
Not
e:•
The
bui
lt-in
CD
pla
yer
play
s on
e st
anda
rd 1
2 cm
or 8
cm
(si
ngle
) C
D a
t a ti
me.
Do
not u
se a
nad
apte
r w
hen
play
ing
8 cm
CD
.•
Don
’t in
sert
any
mat
eria
ls e
xcep
t for
CD
into
CD
load
ing
slot
.
Trac
k Se
arch
and
Fas
t For
war
d/Re
vers
e
•Y
ou c
an s
elec
t be
twee
n T
rack
Sea
rch
or F
ast
For
war
d/R
ever
se b
y pr
essi
ngth
e 2
/3bu
tton
for
a di
ffer
ent
leng
th o
f ti
me.
Tra
ck S
earc
h0.
5 se
cond
s or
less
Fast
For
war
d/R
ever
se
Con
tinue
pre
ssin
g
Not
e:•
If a
dis
c ca
nnot
be
inse
rted
ful
ly o
r pl
ayba
ck f
ails
, mak
e su
re th
e re
cord
ed s
ide
is d
own.
Push
the
EJE
CT
but
ton
and
chec
k th
e di
sc f
or d
amag
e be
fore
rei
nser
ting
it.•
If a
dis
c is
inse
rted
with
the
reco
rded
sid
e up
, it w
ill b
e ej
ecte
d au
tom
atic
ally
aft
er a
few
mom
ents
.•
If th
e bu
ilt-i
n C
D p
laye
r ca
nnot
ope
rate
pro
perl
y, a
n er
ror
mes
sage
(su
ch a
s “E
RR
OR
-14”
)ap
pear
s on
the
disp
lay.
Ref
er to
“B
uilt-
in C
D P
laye
r’s
Err
or M
essa
ge”.
Ejec
t Not
e:•
The
CD
fun
ctio
n ca
n be
turn
ed O
N/O
FFw
ith th
e di
sc r
emai
ning
in th
is p
rodu
ct.
• A
dis
c le
ft p
artia
lly in
sert
ed a
fter
eje
c-tio
n m
ay in
cur
dam
age
or f
all o
ut.
DEH-1330R,1300R,1310
2.R
ear
outp
ut
1.T
his
prod
uct
3.A
nten
naja
ck
4.Fu
se
5.
7.C
ap(1
*)W
hen
notu
sing
this
term
inal
,do
notr
emov
eth
eca
p.
1*
2* 4*
3* 5*
9.Y
ello
w(2
*)To
term
inal
alw
ays
supp
lied
with
pow
erre
gard
less
ofig
nitio
nsw
itch
posi
tion.
8.Y
ello
w(3
*)B
ack-
up(o
rac
cess
ory)
12.B
lack
(gro
und)
Tove
hicl
e(m
etal
)bo
dy.
24.B
lue/
whi
te(7
*)To
Aut
o-an
tenn
are
lay
cont
rol
term
inal
(max
.300
mA
12V
DC
).
6.C
onne
ctle
ads
ofth
esa
me
colo
rto
each
othe
r.
18.B
lue/
whi
teTo
syst
emco
ntro
lter
min
alof
the
pow
eram
p(m
ax.3
00m
A12
VD
C).
23.B
lue/
whi
te(6
*)
11.R
ed(4
*)To
elec
tric
term
inal
cont
rolle
dby
igni
tion
switc
h(1
2V
DC
)O
N/O
FF.
10.R
ed(5
*)A
cces
sory
(or
back
-up)
14.S
peak
erle
ads
Whi
teW
hite
/bla
ckG
ray
Gra
y/bl
ack
Gre
enG
reen
/bla
ckV
iole
tV
iole
t/bla
ck
:Fro
ntle
ft+
:Fro
ntle
ft≠
:Fro
ntri
ght+
:Fro
ntri
ght≠
:Rea
rle
ft+
:Rea
rle
ft≠
:Rea
rri
ght+
:Rea
rri
ght≠
Not
e:D
epen
ding
onth
eki
ndof
vehi
cle,
the
func
tioof
3*an
d5*
may
bedi
ffer
ent.
Inth
isca
se,b
esu
reto
conn
ect2
*to
5*an
d4*
to3*
.
20.R
ear
spea
ker
(Lef
t)
19.S
yste
mre
mot
eco
ntro
l
16.P
ower
amp
(sol
dse
para
tely
)
15.C
onne
ctin
gco
rds
with
RC
Api
npl
ugs
(sol
dse
para
tely
).
22.P
erfo
rmth
ese
conn
ectio
nsw
hen
usin
ga
diff
eren
tam
p(s
old
sepa
rate
ly).
21.R
ear
spea
ker
(Rig
ht)
25.
13.I
SOco
nnec
tor
Not
e:In
som
eve
hicl
es,t
heIS
Oco
nnec
tor
may
bedi
vide
din
totw
o.In
this
case
,be
sure
toco
nnec
tto
both
conn
ecto
rs.
The
pin
posi
tion
ofth
eIS
Oco
nnec
tor
will
diff
erde
pend
son
the
type
ofve
hicl
e.C
onne
ct6*
and
7*w
hen
Pin
5is
anan
tenn
aco
ntro
ltyp
e.In
anot
her
type
ofve
hicl
e,ne
ver
conn
ect6
*an
d7*
.
17.Y
ello
w/b
lack
Ifyo
uus
ea
cellu
lar
tele
phon
e,co
nnec
titv
iath
eA
udio
Mut
ele
adon
the
cellu
lar
tele
phon
e.If
not,
keep
the
Aud
ioM
ute
lead
free
ofan
yco
nnec
tions
.
+ ≠
+ ≠
Conn
ectio
n D
iagr
am (D
EH-1
330R
,130
0R)
72
73
DEH-1330R,1300R,1310
+ ≠
+ ≠
+ ≠
+ ≠
+ ≠
+ ≠
Blu
e/w
hite
Tosy
stem
cont
rolt
erm
inal
ofth
epo
wer
amp
orA
uto-
ante
nna
rela
yco
ntro
lter
min
al(m
ax.3
00m
A12
VD
C)
.
Con
nect
ing
cord
sw
ithR
CA
pin
plug
s(s
old
sepa
rate
ly)
Syst
emre
mot
eco
ntro
l
Rea
rsp
eake
rR
ear
spea
ker
Rig
ht
Fron
tspe
aker
Rea
rsp
eake
r
Whi
teG
ray
Whi
te/b
lack
Gre
en
Gre
en/b
lack
Gra
y/bl
ack
Vio
let
Vio
let/b
lack
Fron
tspe
aker
Rea
rsp
eake
r
Left
Perf
orm
thes
eco
nnec
tions
whe
nus
ing
adi
ffer
enta
mp
(sol
dse
para
tely
).
With
a2
spea
ker
syst
em,d
ono
tcon
nect
anyt
hing
toth
esp
eake
rle
ads
that
are
not
conn
ecte
dto
spea
kers
.
Yel
low
Tote
rmin
alal
way
ssu
pplie
dw
ithpo
wer
rega
rdle
ssof
igni
tion
switc
hpo
sitio
n.
Bla
ck(g
roun
d)To
vehi
cle
(met
al)
body
.
Red
Toel
ectr
icte
rmin
alco
ntro
lled
byig
nitio
nsw
itch
(12
VD
C)
ON
/OFF
.
Pow
eram
p(s
old
sepa
rate
ly)
Fuse
Yel
low
/bla
ckIf
you
use
ace
llula
rte
leph
one,
conn
ecti
tvia
the
Aud
ioM
ute
lead
onth
ece
llula
rte
leph
one.
Ifno
t,ke
epth
eA
udio
Mut
ele
adfr
eeof
any
conn
ectio
ns.
Rea
rou
tput
Thi
spr
oduc
t
Ant
enna
jack
Conn
ectio
n D
iagr
am (D
EH-1
310)
74
DEH-1330R,1300R,1310
8.2 SPECIFICATIONS
GeneralPower source .......... 14.4 V DC (10.8 – 15.1 V allowable)Grounding system ........................................ Negative typeMax. current consumption ...................................... 10.0 ADimensions
Weight ...................................................................... 1.4 kgElectrode dark current .................................... 6mA or less
Amplifier Maximum power output ...................................... 45 W × 4Continuous power output .................................... 25 W × 4
Loudness contour(Low) .................. +3.5 dB (100 Hz), +3 dB (10 kHz)(Mid) ................ +10 dB (100 Hz), +6.5 dB (10 kHz)(High) ................ +11 dB (100 Hz), +11 dB (10 kHz)
Number of quantization bits: 16; linearFrequency characteristics................ 5 – 20,000 Hz (±1 dB)Signal-to-noise ratio ........ 94 dB (1 kHz) (IEC-A network)Dynamic range ............................................ 92 dB (1 kHz)Number of channels ............................................ 2 (stereo)
FM tunerFrequency range ...................................... 87.5 – 108 MHzUsable sensitivity
LW tunerFrequency range ........................................ 153 – 281 kHzUsable sensitivity .............................. 30 µV (S/N: 20 dB)Selectivity .................................................. 50 dB (±9 kHz)
Note:• Specifications and the design are subject to possi-
ble modification without notice due to improve-ments.
- DEH-1330R,1300R
75
DEH-1330R,1300R,1310
- DEH-1310
GeneralPower source .......... 14.4 V DC (10.8 – 15.1 V allowable)Grounding system ........................................ Negative typeMax. current consumption ...................................... 10.0 ADimensions
Weight ...................................................................... 1.4 kgElectrode dark current .................................... 6mA or less
AmplifierMaximum power output ...................................... 45 W × 4Continuous power output .................................... 25 W × 4
Loudness contour(Low) ..................+3.5 dB (100 Hz), +3 dB (10 kHz)(Mid) ..................+10 dB (100 Hz), +6.5 dB (10 kHz)(High) ..................+11 dB (100 Hz), +11 dB (10 kHz)
(volume: –30 dB)
CD playerSystem .................................... Compact disc audio systemUsable discs .................................................. Compact discSignal format .................... Sampling frequency: 44.1 kHz
Number of quantization bits: 16; linearFrequency characteristics .............. 5 – 20,000 Hz (±1 dB)Signal-to-noise ratio ...... 94 dB (1 kHz) (IEC-A network)Dynamic range ............................................ 92 dB (1 kHz)Number of channels ............................................ 2 (stereo)
FM tunerFrequency range ............................................ 65 – 74 MHz