PECIAL FEAUTRES - Astrodyne TDI IEC 60068‐2‐64 Spectrum A.1: Transportation Category 2 (Water, land, hard conditions, Railcar with hard suspension trailers) 30min/axis on all three
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
www.As
AGEN
Providexcellmaintthe idindustconveintern
MODEL
NUMBER
SPS5930
SPS6011
SPS5975
SPS5936
SPS5933
strodyneTDI.
NCY/ COMPL
EN61000‐4
Severity Lev
EN61000‐4
SEMI F47‐0
11kW Load
EMI: Desig
2004 with e
UL60950‐1,
EN60950‐1
IEC60950‐1
ding high opent reliability
tainability; Lieal choice fotrial and milierter featuresnational pow
PART N
‐1‐LF T1001
‐1‐LF T100
5‐LF T100
6‐LF T100
3‐LF T100
T10
com | +1 908
LIANCE
‐4 1995 Elect
vel 3
‐5 1995 Surge
0706 ‐ Criteria
)
gned to meet
external filter
, 2nd Edition
/A12:2011
1, 2nd Edition
erating efficy, compact siquaBladeTM or high poweitary applicas, automaticer input.
NUMBER
103091‐1‐LF
0108057‐LF
0104286‐LF
0103270‐LF
0103381‐LF
00108634
* Consult facto
8‐850‐5088
trical Fast Tra
e ‐ Severity Le
a A (Operating
CISPR 11 Clas
r (consult fact
, CE Marked
ciency along size, and easpower supper DC systemtions. The
PAGE 2 of 15 www.AstrodyneTDI.com | +1 908‐850‐5088
* Consult factory for other model specifications
PROTECTION FEATURES
Output Over-voltage: Output protected with over-voltage shutdown circuitry. Output will latch off if output voltage reaches 63V (+/-1V)
Output over-current: Automatic electronic current limit circuitry Over-temperature: Internal thermal monitoring circuits shut down unit if temperatures exceed safe limits. Unit will automatically
power back on after cool down.
ALARMS AND CONTROLS
AC Good/ DC Good/Fault: Multi-colored front panel LED Control & Admin: All alarms and controls available via CAN Bus connectors at back of unit. Signals include: Voltage Command,
Current Command, AC Input OK, DC Output Enabled, Temperature Fault, DC Output Voltage, DC Output Current, Sub-Assemblies OK (1- 3)
OUTPUT SPECIFICATIONS T100103091‐1‐LF*
Voltage Adjustable from 5‐60VDC can also be set to 0V ; Constant Voltage Mode: +/-1.5V 0‐60VDC
Current Can be programmed in constant current mode from 0‐360A; Constant Current Mode: +/-0.5%
360 Amps Maximum
Power Programmable; Constant Power Mode: +/-1% 16,500W Max
Line Regulation Less than 1%
Load Regulation 10%Load - Full load 1%
Ripple and Noise 20MHz BW Less than 300mV p-p Parallel Use May be paralleled with other like units for increased output power. Active “or-ing” MOSFETTemperature Coeff. Average over 8 hours, (after 30 minute warm up) <50ppm/oC of set pointTurn On Time 2 Seconds Max
ENVIRONMENTAL CONDITIONS
Cooling Water cooled – water temperature range from 10°C to 55°C (Consult factory for other temperatures or coolants)
Flow Rate: 1.5 – 2.5 gallons per minute
Pressure drop: pressure at 2gpm <10psi Maximum pressure: 60psi continuous
Ambient Temperature +5 to +50°C
Storage Temperature ‐40 to +85°C (coolant lines purged)
Humidity 0 to 95% non‐condensing, operating and storage