1 Overview Milling Cutters made of HSS-E and PM (powder steel) Manufacturer ß 0 0 0 0 ß 0 0 ß ß Standard/DIN Works norm Works norm Works norm Works norm Works norm Works norm 327D 327D 327D 327D Number of flutes 1 3 3 3 3 2 - 3 2 2 2 2 Diameters mm 3 - 8 1 - 20 1 - 20 2 - 10 2 - 10 2 - 6 1 - 40 1 - 40 4 - 20 2,5 - 25 Material HSS-E HSS-E HSS-E HSS-E HSS-E HSS-E HSS-E HSS-E PM HSS-E Coating – – TiAlN – TiAlN – – TiAlN TiAlN – Type short short short long long short short short short long Type W N N N N Radius N N N N Page in catalogue 16.10 16.11 16.11 16.11 16.11 16.12 16.12 16.12 16.12 16.13 Item number 16010 16020 16022 16030 16032 16035 16060 16062 16075 16073 Suitability Aluminium < 10% Si W X X X X X X X X X Aluminium > 10% Si W X X X X X X X X X Copper X X X X X X X X X Steel < 520N W W W W W W W W W Steel < 750N W W W W W W W W W Steel < 900N W W W W W W W W W Steel < 1100N W W W W Steel < 1200N W W W W Steel < 1400N W VA-steel < 900N X X X X X X X W X VA-steel > 900N X X X X X X X W X GG X X X X X X X W X GGG X X X X X X X W X Titaniumium W Titaniumium alloys W Nickel X < 55HRC < 60HRC < 67HRC Plastics X X X X X X X X Manufacturer ß ß 0 0 0 0 0 0 0 0 Standard/DIN 327D 844B 844B 844B 844B 844B 844B 844B 844B 844B Number of flutes 2 3 3 3 3 3 4 - 6 4 - 6 4 - 5 4 - 6 Diameters mm 2,5 - 20 1,5 - 30 1,5 - 30 4 - 20 2 - 30 2 - 30 2 - 30 2 - 30 5 - 30 10 - 32 Material HSS-E HSS-E HSS-E PM HSS-E HSS-E HSS-E HSS-E PM PM Coating TiAlN – TiAlN TiAlN – TiAlN – TiAlN TiAlN TiAlN Type long short short short long long short short short short Type N N N N N N N N N N/IKZ Page in catalogue 16.13 16.14 16.14 16.14 16.15 16.15 16.16 16.16 16.16 16.16 Item number 16074 16094 16096 16100 16104 16105 16120 16122 16131 16132 Suitability Aluminium < 10% Si W X X X X X X X X X Aluminium > 10% Si W X X X X X X X X X Copper X X X X X X X X X Steel < 520N W W W W W W W W W Steel < 750N W W W W W W W W W Steel < 900N W W W W W W W W W Steel < 1100N W W W W W Steel < 1200N W W W W W Steel < 1400N W W W VA-steel < 900N X X X W X X X X W VA-steel > 900N X X X W X X X X W GG X X X W X X X X W W GGG X X X W X X X X W W Titaniumium W W W Titaniumium alloys W W W Nickel X X X < 55HRC < 60HRC < 67HRC Plastics X X X X X X X W = suitable X = partially suitable W = suitable X = partially suitable eng/OP www.hhw.de 16.1
74
Embed
Overview Milling Cutters made of HSS-E and PM (powder ...katalog.hhw.de/EN/16_HHW_Katalog_2010_eng.pdf1 Overview Milling Cutters made of HSS-E and PM (powder steel) Manufacturer ß
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
1Overview Milling Cutters made of HSS-E and PM (powder steel)
Manufacturer ß 0 0 0 0 ß 0 0 ß ß
Standard/DIN Works norm Works norm Works norm Works norm Works norm Works norm 327D 327D 327D 327D
Number of flutes 1 3 3 3 3 2 - 3 2 2 2 2Diameters mm 3 - 8 1 - 20 1 - 20 2 - 10 2 - 10 2 - 6 1 - 40 1 - 40 4 - 20 2,5 - 25Material HSS-E HSS-E HSS-E HSS-E HSS-E HSS-E HSS-E HSS-E PM HSS-ECoating – – TiAlN – TiAlN – – TiAlN TiAlN –Type short short short long long short short short short longType W N N N N Radius N N N NPage in catalogue 16.10 16.11 16.11 16.11 16.11 16.12 16.12 16.12 16.12 16.13Item number 16010 16020 16022 16030 16032 16035 16060 16062 16075 16073
SuitabilityAluminium < 10% Si W X X X X X X X X XAluminium > 10% Si W X X X X X X X X XCopper X X X X X X X X XSteel < 520N W W W W W W W W WSteel < 750N W W W W W W W W WSteel < 900N W W W W W W W W WSteel < 1100N W W W WSteel < 1200N W W W WSteel < 1400N WVA-steel < 900N X X X X X X X W XVA-steel > 900N X X X X X X X W XGG X X X X X X X W XGGG X X X X X X X W XTitaniumium WTitaniumium alloys WNickel X< 55HRC< 60HRC< 67HRCPlastics X X X X X X X X
Number of flutes 2 3 3 3 3 3 4 - 6 4 - 6 4 - 5 4 - 6Diameters mm 2,5 - 20 1,5 - 30 1,5 - 30 4 - 20 2 - 30 2 - 30 2 - 30 2 - 30 5 - 30 10 - 32Material HSS-E HSS-E HSS-E PM HSS-E HSS-E HSS-E HSS-E PM PMCoating TiAlN – TiAlN TiAlN – TiAlN – TiAlN TiAlN TiAlNType long short short short long long short short short shortType N N N N N N N N N N/IKZPage in catalogue 16.13 16.14 16.14 16.14 16.15 16.15 16.16 16.16 16.16 16.16Item number 16074 16094 16096 16100 16104 16105 16120 16122 16131 16132
SuitabilityAluminium < 10% Si W X X X X X X X X XAluminium > 10% Si W X X X X X X X X XCopper X X X X X X X X XSteel < 520N W W W W W W W W WSteel < 750N W W W W W W W W WSteel < 900N W W W W W W W W WSteel < 1100N W W W W WSteel < 1200N W W W W WSteel < 1400N W W WVA-steel < 900N X X X W X X X X WVA-steel > 900N X X X W X X X X WGG X X X W X X X X W WGGG X X X W X X X X W WTitaniumium W W WTitaniumium alloys W W WNickel X X X< 55HRC< 60HRC< 67HRCPlastics X X X X X X X
W = suitable X = partially suitable
W = suitable X = partially suitable
eng/OP www.hhw.de 16.1
1
eng/OPwww.hhw.de16.2
Overview Milling Cutters made of HSS-E and PM (powder steel)Manufacturer 0 0 0 0 0 0 0 0 0 0
Number of flutes 4 - 6 4 - 6 4 - 6 4 - 6 4 - 6 4 - 6 6 - 8 2 3 3Diameters mm 6 - 25 6 - 25 2 - 25 2 - 25 6 - 25 6 - 25 30 -50 2 - 25 3 - 30 3 - 30Material PM PM HSS-E HSS-E HSS-E HSS-E HSS-E HSS-E HSS-E HSS-ECoating – TiAlN – TiAlN – TiAlN – – – –Type medium medium long long extra long extra long short short short longType N N N N N N N W W WPage in catalogue 16.17 16.17 16.17 16.17 16.18 16.18 16.18 16.18 16.19 16.19Item number 16143 16144 16128 16129 16133 16134 16150 16153 16158 16161
SuitabilityAluminium < 10% Si X X X X X X X W W WAluminium > 10% Si X X X X X X X W W WCopper X X X X X X X W W WSteel < 520N W W W W W W W W W WSteel < 750N W W W W W W W W W WSteel < 900N W W W W W W W W W WSteel < 1100N W W W WSteel < 1200N W W W WSteel < 1400N WVA-steel < 900N W W X X X X XVA-steel > 900N W W X X X X XGG W W X X X X XGGG W W X X X X XTitanium WTitanium alloys WNickel X< 55HRC< 60HRC< 67HRCPlastics X X X X X X X
Manufacturer 0 0 0 ß ß ß ß ß ß ß
Standard/DIN Works norm Works norm Works norm 844B 844B 844B 844B 844B Works norm Works norm
Number of flutes 2 2 2 3 3 4 - 6 4 - 6 4 - 6 4- 5 4 - 5Diameters mm 2 - 25 2 - 30 2 - 30 6 - 40 6 - 40 10 - 40 10 - 40 8 - 36 10 - 25 6 - 25Material HSS-E HSS-E HSS-E HSS-E HSS-E HSS-E HSS-E HSS-E HSS-E HSS-ECoating – – TiAlN – TiAlN – TiAlN – – TiAlNType short long long short short short short long special long extra longType Radius Radius Radius NR NR NR NR NR NR NRPage in catalogue 16.19 16.20 16.20 16.20 16.20 16.21 16.21 16.21 16.22 16.22Item number 16170 16176 16177 16183 16185 16195 16198 16200 16207 16209
SuitabilityAluminium < 10% Si X X X X X X X X X XAluminium > 10% Si X X X X X X X X X XCopper X X X X X X X X X XSteel < 520N W W W W W W W W W WSteel < 750N W W W W W W W W W WSteel < 900N W W W W W W W W W WSteel < 1100N W W W WSteel < 1200N W W W WSteel < 1400NVA-steel < 900N X X X X X X X X X XVA-steel > 900N X X X X X X X X X XGG X X X X X X X X X XGGG X X X X X X X X X XTitaniumTitanium alloysNickel< 55HRC< 60HRC< 67HRCPlastics X X X X X X X X
Number of flutes 4 - 6 6 - 8 3 3 3 4 4 4 - 6 4 - 6 4 - 6Diameters mm 6 - 32 30 - 50 6 - 30 6 - 40 6 - 40 6 - 25 6 - 25 6 -25 10 - 32 6 - 25Material PM HSS-E HSS-E HSS-E HSS-E HSS-E HSS-E PM PM PMCoating TiCN – – – TiAlN – – TiAlN TiAlN TiAlNType short short short short short short short short short mediumType NR-Pro NR WR NF NF HR HR HR HR/IKZ HRPage in catalogue 16.22 16.23 16.23 16.23 16.23 16.24 16.24 16.24 16.24 16.24Item number 16203 16205 16210 16220 16223 16260 16262 16268 16269 16271
SuitabilityAluminium < 10% Si X X X X X X X X X XAluminium > 10% Si X X X X X X X X X XCopper X X X X X X X X X XSteel < 520N W W W W W W W W W WSteel < 750N W W W W W W W W W WSteel < 900N W W W W W W W W W WSteel < 1100N W W W W WSteel < 1200N W W W W WSteel < 1400N W WVA-steel < 900N W X X X X X X X X WVA-steel > 900N W X X X X X X X WGG W X X X X X X X X WGGG W X X X X X X X X WTitanium W WTitanium alloys W WNickel X X< 55HRC< 60HRC< 67HRCPlastics X X X X X X X X
Number of flutes 3 - 6 3 - 6 3 - 4 6 - 12 6 - 12 8 - 12 8 - 12 8 - 12 8 - 12 4 - 6 4 - 6Diameters mm 6 - 30 6 - 30 6 - 40 12,5 - 50 4,5 - 45,5 16 - 32 16 - 32 16 - 32 16 - 32 10 - 56 10 - 40Material HSS-E HSS-E HSS-E HSS-E HSS-E HSS-E HSS-E HSS-E HSS-E HSS-E HSS-ECoating – TiAlN TiAIN – – – – – – – –Type long long short short short short short short short short shortType HR HR Radius N N N N N N N NPage in catalogue 16.25 16.25 16.25 16.26 16.26 16.27 16.27 16.27 16.27 16.27 16.28Item number 16277 16278 16281 16370 16375 16380 16381 16382 16383 16385 16390
SuitabilityAluminium < 10% Si X X X X X X X X X X XAluminium > 10% Si X X X X X X X X X X XCopper X X X X X X X X X X X XSteel < 520N W W W W W W W W W W WSteel < 750N W W W W W W W W W W WSteel < 900N W W W W W W W W W W WSteel < 1100N W WSteel < 1200N WSteel < 1400NVA-steel < 900N X X X X X X X X X X XVA-steel > 900N X X X X X X X X X X XGG X X X X X X X X X X XGGG X X X X X X X X X X XTitaniumTitanium alloysNickel< 55HRC< 60HRC< 67HRCPlastics X X X X X X X X X X X
Number of flutes 1 3 3 2 2 2 2 2 2 2Diameters mm 1,5 - 16 1,0 - 20 1,5 - 20 2 - 20 2 - 20 3 - 25 3 - 25 3 - 25 3 - 25 4 - 20Material VHM VHM VHM VHM VHM VHM VHM VHM VHM VHMCoating – – TiAlN – TiAlN – – Alu-CC Alu-CC AluCCType short short short short short short/long short/long short/long short/long short/longType W N N N N W W W W WFPage in catalogue 16.28 16.28 16.28 16.29 16.29 16.30 16.30 16.30 16.30 16.31Item number 16485 16500 16502 16505 16507 16512 2.. 16512 3.. 16513 2.. 16513 3.. 16514
SuitabilityAluminium < 10% Si W X X X X W W WAluminium > 10% Si W X X X X W W WCopper W X X X X W W WSteel < 520N W W W WSteel < 750N W W W WSteel < 900N W W W WSteel < 1100N W W W WSteel < 1200N W W W WSteel < 1400N W W W WVA-steel < 900N X W X W W WVA-steel > 900N X W X W W WGG W W W WGGG W W W WTitanium X W X W W WTitanium alloys X W X W W WNickel X W X W W W< 55HRC< 60HRC< 67HRCPlastics W W X W X W W W
Manufacturer ß ß ß 0 0 0 0 0 0 0
Number of flutes 2 3 3 3 3 3 3 3 3 3Diameters mm 3 - 20 2 - 20 2 - 20 3 - 25 3 - 25 3 - 25 3 - 25 3 - 25 3 - 24 3 - 24Material VHM VHM VHM VHM VHM VHM VHM VHM VHM VHMCoating TiAlN – TiAlN – – AluCC AluCC – – AluCCType long short short short/long short/long short/long short/long short/long short/long short/longType N N N W W W W W W WPage in catalogue 16.31 16.32 16.32 16.33 16.33 16.33 16.33 16.34 16.34 16.34Item number 16517 16522 16524 16528 2.. 16528 3.. 16529 2.. 16529 3.. 16530 2.. 16530 3.. 16531 2..
SuitabilityAluminium < 10% Si X X X W W W W W W WAluminium > 10% Si X X X W W W W W W WCopper X X X W W W W W W WSteel < 520N W W WSteel < 750N W W WSteel < 900N W W WSteel < 1100N W W WSteel < 1200N W W WSteel < 1400N W W WVA-steel < 900N W X W WVA-steel > 900N W X W WGG W W WGGG W W WTitanium W X W W W WTitanium alloys W X W W W WNickel W X W W W W< 55HRC< 60HRC< 67HRCPlastics X W X W W W W W W W
W = suitable X = partially suitable
W = suitable X = partially suitable
1
eng/OP www.hhw.de 16.5
Manufacturer 0 ß ß ß ß ß ß 0 0 ß
Number of flutes 3 4 4 4 4 4 4 4 4 4Diameters mm 3 - 25 4 - 20 4 - 20 4 - 25 4 - 20 4 - 20 6 - 20 3 - 25 3 - 25 4 - 20Material VHM VHM VHM VHM VHM VHM VHM VHM VHM VHMCoating AluCC TiAlN TiAlN TiAIN TiAIN TiAIN TIAlN AluCC AluCC TiAlNType short/long short long long long long/clamping surface long long long longType W H H VA-steel H H H/35°/38° W W H/Corner radiusPage in catalogue 16.34 16.35 16.35 16.35 16.35 16.36 16.37 16.37 16.37 16.38Item number 16531 3.. 16533 16534 1.. 16534 2.. 16534 3.. 16536 16538 1.. 16538 2.. 16538 3.. 16540 1..
SuitabilityAluminium < 10% Si W W W W W W W W WAluminium > 10% Si W W W W W W W W WCopper W W W W W W W W WSteel < 520N W W W W W W WSteel < 750N W W W W W W WSteel < 900N W W W W W W WSteel < 1100N W W W W W WSteel < 1200N W W W W W WSteel < 1400NVA-steel < 900N X W W W W W W W WVA-steel > 900N X W W W W W W W WGG W W W W W WGGG W W W W W WTitanium W W W W W W W W WTitanium alloys W W W W W W W W WNickel W W W W W W W W W< 55HRC< 60HRC< 67HRCPlastics W W W
Manufacturer ß ß ß ß ß ß ß ß ß ß
Number of flutes 4 4 4 4 4 4 4 4 4 4Diameters mm 3 - 25 3 - 25 2 - 20 2 - 20 4 - 20 4 - 20 3 - 20 3 - 20 3 - 12 3 - 12Material VHM VHM VHM VHM VHM VHM VHM VHM VHM VHMCoating AluCC AluCC – TiAlN – TiAlN – TiAlN – TiAlNType long long short short long long long long extra long extra longType W/35°/38° W/35°/38° N N N N N N N NPage in catalogue 16.38 16.38 16.39 16.39 16.39 16.39 16.40 16.40 16.40 16.40Item number 16540 2.. 16540 3.. 16537 16539 16542 16543 16545 16547 16548 16549
SuitabilityAluminium < 10% Si W W X X X X X X X XAluminium > 10% Si W W X X X X X X X XCopper W W X X X X X X X XSteel < 520N W W W W W W W WSteel < 750N W W W W W W W WSteel < 900N W W W W W W W WSteel < 1100N W W W W W W W WSteel < 1200N W W W W W W W WSteel < 1400N W W W W W W W WVA-steel < 900N X W X W X X X WVA-steel > 900N X W X W X X X WGG W W W W W W W WGGG W W W W W W W WTitanium W W X W X W X W X WTitanium alloys W W X W X W X W X WNickel W W X W X W X W X W< 55HRC< 60HRC< 67HRCPlastics W W W X W X W X W X
W = suitable X = partially suitable
W = suitable X = partially suitable
1Overview Solid Carbide Milling Cutters
Manufacturer ß ß ß ß ß ß ß ß ß ß
Number of flutes 6 - 8 6 - 8 2 2 4 4 4 4 4 - 6 4 - 6Diameters mm 6 - 20 6 - 20 3 - 20 2 - 20 2 - 20 5 -20 3 - 20 6 - 20 4 - 20 4 - 20Material VHM VHM VHM VHM VHM VHM VHM VHM VHM VHMCoating TiAlN TiAlN TiAlN TiAlN TiAlN TiAlN TiAlN TiAlN – TiAlNType long extra long short long short long long long short shortType N N Radius Radius Radius NF HR HR / IKZ 90° Deburrer 90° DeburrerPage in catalogue 16.41 16.41 16.41 16.42 16.42 16.42 16.43 16.43 16.43 16.43Item number 16551 16553 16557 16559 16561 16565 16567 16569 16570 16571
SuitabilityAluminium < 10% Si X W X X X X X X XAluminium > 10% Si X W X X X X X X XCopper X W X X X X X X XSteel < 520N W W W W W W W W W WSteel < 750N W W W W W W W W W WSteel < 900N W W W W W W W W W WSteel < 1100N W W W W W W W W W WSteel < 1200N W W W W W W W W W WSteel < 1400N W W W W W W W W W WVA-steel < 900N W W W W W W W W X WVA-steel > 900N W W W W W W W W X WGG W W W W W W W W W WGGG W W W W W W W W WTitanium W W W W W W W W X WTitanium alloys W W W W W W W W X WNickel W W W W W W W W X W< 55HRC< 60HRC< 67HRCPlastics X X X X X X X W X
Manufacturer ß ß ß ß ß 0 ß 0 ß 0
Number of flutes 4 - 6 4 - 6 2 4 2 2 2 3 4 4Diameters mm 4 - 20 4 - 20 3 - 20 4 - 16 1 - 25 0,3 - 20 3 - 25 3 - 20 2 - 25 2 - 20 Material VHM VHM VHM VHM VHM VHM VHM VHM VHM VHMCoating – TiAlN – TiAlN TiAlN TiAlN Ultra TiAlN TiAlN Ultra TiAlN TiAlN UltraType short short short long short Undercut long Undercut short short undercutType 60° Deburrer 60° Deburrer Universal Deburrer HSC HSC HSC HSC HSC HSCPage in catalogue 16.44 16.44 16.44 16.44 16.56 16.57 16.58 16.58 16.59 16.59Item number 16572 16573 16580 16583 16601 16603 16604 16607 16609 16610
SuitabilityAluminium < 10% Si X X X X W WAluminium > 10% Si X X X X W WCopper X X X X W WSteel < 520N W W W W W W W W W WSteel < 750N W W W W W W W W WSteel < 900N W W W W W W W W WSteel < 1100N W W W W W W W W WSteel < 1200N W W W W W W W WSteel < 1400N W W W WVA-steel < 900N W X W WVA-steel > 900N W X W WGG W W W W W WGGG W W W W W WTitanium W X W W W WTitanium alloys W X W W W WNickel W X W W W W< 55HRC X W X W W< 55HRC W X X W< 60HRC W< 67HRCPlastics W X W X W W
W = suitable X = partially suitable
W = suitable X = partially suitable
eng/OPwww.hhw.de16.6
1
eng/OP www.hhw.de 16.7
Manufacturer ß ß 0 ß ß ß ß ß ß ß
Number of flutes 4 8 - 16 6 - 8 6 2 4 2 4 3 - 6 3 - 4Diameters mm 3 - 25 6 - 20 4 - 20 6 - 25 1 - 25 1 - 25 1 - 16 R 0,5 - 6,0 4 - 25 6 - 20Material VHM VHM VHM VHM VHM VHM VHM VHM VHM VHMCoating TiAlN TiAlN TiAlN Ultra TiAlN TiAlN TiAlN TiAlN TiAlN TiAlN TiAlNType long long/extra long short undercut extra long Radius long Radius long Radius extra long long Quater circle longType HSC HSC HSC HSC HSC HSC Type H HR / HSC HR / HSCPage in catalogue 16.60 16.60 16.61 16.61 16.62 16.62 16.62 16.63 16.63 16.63Item number 16613 16614 16616 16619 16621 16625 16655 16658 16650/651 16629
SuitabilityAluminium < 10% Si XAluminium > 10% Si XCopper W XSteel < 520N W W W W W W W W W WSteel < 750N W W W W W W W W W WSteel < 900N W W W W W W W W W WSteel < 1100N W W W W W W W W W WSteel < 1200N W W W W W W W W W WSteel < 1400N W W W W W W W W W WVA-steel < 900N W W W X WVA-steel > 900N W W W X WGG W W W X W WGGG W W W W WTitanium X WTitanium alloys X WNickel W W W X W< 50HRC W W W W W W W W W W< 55HRC W W X W W X X X W W< 60HRC W W W W W X< 67HRC X X XPlastics
SuitabilityAluminium < 10% SiAluminium > 10% SiCopper WGraphit W W WSteel < 520N W W W W WSteel < 750N W W W W W WSteel < 900N W W W W W WSteel < 1100N W W W W W WSteel < 1200N W W W W WSteel < 1400N W W W W WVA-steel < 900NVA-steel > 900NGG W WGGG W WTitaniumTitanium alloysNickel< 50HRC W W W W W W< 55HRC X W W W W X< 60HRC W W W W W< 67HRC X X X XPlastics
W = suitable X = partially suitable
W = suitable X = partially suitable
1
eng/OPwww.hhw.de16.8
Overview milling cutters made of Solid carbide for hard- and high-speed machining0 0 0 0 0 0
Cat.-no. 16800 16801 16802 16805 16806 16810
Ø range in mm 0,1 - 0,9 0,2 - 3 0,2 - 3 0,1 - 0,9 0,2 - 3 3 - 20
Teeth 2 2 2 2 2 4
Material HRC 52 65 52 65 52 65 52 65 52 65 52 65M10 Cast iron, soft GG10-GG20 W W W W W W
M11 Cast iron GG25-GG35 W W W W W W
M12 Cast iron GGG40-GGG50 W W W W W W
M13 Cast iron GGG60-GGG90 W W W W W W
M14 Malleable cast iron W W W W W W
M15 Steel and cast steel < 700 N/mm2W W W W W W
M18 Steel and cast steel 700-1000 N/mm2W W W W W W
M25 Steel 1000-1300 N/mm2W W W W W W
M22 Steel 1300-1600 N/mm2W W W W W W
M16 Stainless steel W W W W W W
M20 Stainless steel (≤ 2% Ni) W W W W W W
M17 Titanium (alloys) < 700 N/mm2W W W W W W
M21 Titanium (alloys) > 700 N/mm2W W W W W W
M19 Ni and Co alloys < 900 N/mm2W W W W W W W W W W W W W
M23 Ni and Co alloys < 1200 N/mm2W W W W W W W W W W W W W
M24 Ni and Co alloys > 1200 N/mm2W W W W W W W W W W W W W
M26 Hardened steel< 52 HRC W W W W W W W W W W W W
0ßApplicationWith the cutting rate calculator (German language)you can quickly and easily find the correct values
for all ATORN and HHW milling cutters andturning tools.
16900 101
n 16900 …min-1
10 - 30.000 101
16900
Cutting rates USB flash drive
0ß
TypeThe cutting rates USB flash drive contains all releva-nt cutting data and will be updated regularly when it
is used with a PC with an internet connection.There will also be a link to the online shop, whichfacilitates reordering.The flash drive provides an additional 2 GBmemory space for your data!
16900 102
16900 …
102
16900
End Milling Cutter Stands
TypeStand body made of red injection plastics. Stable,handy, good fit. Tools with short clamping shankstick out of the mounting hole, so that they are easyto remove. All holes are open at the bottom,therefore no blockage, caused by, e.g. chips.Slightly tapered holes for easy handling of millingcutters. Milling cutters not included.
16005 101TypeSquare (182 x 182 x 30 mm), shank mountingboreholes with 7 different diameters for storing 77end milling cutters.
16005 102-108TypeRectangular (140 x 70 x 30 mm), shank mountingboreholes with same diameter for storing millingcutters with same shank diameter.ApplicationThe different stand types can be completed to astand storage system. Each stand element equippedwith dovetail couplings on the sides.They provide an invisible connection, thereforecombinations look like a one-piece unit.
16005 101
Shank mounting boreholes end milling cutter capacity 16005 …mm pcs.
6 - 25 77 1016 72 1028 50 103
10 32 10412 21 10516 18 10620 10 10725 8 108
16005 102-108
16005
One-Flute Milling Cutters
ßTypeStraight shank, with only one flute, sidewise andface cutting.ApplicationFor milling slots in aluminium doors and windows byhigh-speed milling machines.
0TypeShort, right-hand cut, right-hand helix 30°, 3 cutting blades, centre cut, straight shank withdriving face in compliance with DIN 1835 B.
Note:Regrinding milling cutters with low flute diameters isuneconomical. For that reason, it is cheaper to usethe miniature milling cutters up to the wear limit andthen to throw them away. You are always usingbrand new milling cutters and are reducing the riskof rejections.
0TypeLong, right-hand cut, right-hand helix 30°, 3 cutting blades, centre cut, straight shank withdriving face in compliance with DIN 1835 B.
Note:Regrinding milling cutters with low flute diameters isuneconomical. For that reason, it is cheaper to usethe miniature milling cutters up to the wear limit andthen to throw them away. You are always usingbrand new milling cutters and are reducing the riskof rejections.
Schaftfräser DIN 844 B, Typ N16131 Keyway Milling Cutters
0TypeLong type, right-hand cut, right-hand helix approx.30°, 2 flutes, above 4,0 mm Ø centre cut. Witheccentric relief, above Ø 10,0 mm with double relief.Straight shank with driving face in compliance withDIN 1835 B, above 25 mm shank Ø with 2 drivingfaces.Advantage:No radially ground land, therefore better support andfree cut.
The HHW colour-coding system enables you to see at once which tool is suitable for which material. In most sections of the catalogue, HHW provides you with additional information and data for the respective tool.
The HHW colour-coding system is structured logically and in accordance with the steel key system.
This means, you can choose your tools before the start of the project and therefore you will save time and money.
0TypeLong, right-hand cut, right-hand helix approx. 30°, 3 cutting blades, centre cut. Straight shank with driving face in compliance withDIN 1835 B.
16104QualityHSS-E (Co8).
16105QualityHSS-E (Co8)/TiAlN-coated.
HSS-ETiAIN
16105Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics
100 90 90 80 65 65 45 30 - - - - - 30 20 - 65 -
16104Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics
70 60 60 50 40 40 30 20 - - - - - 20 15 10 40 -
Z 3
Performance requires quality.www.atorn.com
Roughing end milling cutter by ATORN:
ATORN‘s high-quality milling tools.
1
eng/OP
• End milling cutters
www.hhw.de16.16
1 End Milling Cutters
TypeShort, right-hand cut, 4-6 flutes, centre cut.Straight shank with driving face in compliance with DIN 1835 B, starting at 25 mm, shank Ø with 2 driving faces.
ßType Medium length, right-hand cut, right-hand helixapprox. 40°, centre cut, 4-6 flutes. With eccentricrelief. With straight shank with driving face andclamping surface in compliance with DIN 1835 B.
0TypeLong, right-hand cut, right-hand helix approx. 30°, 4-6 flutes, centre cut. Straight shank with drivingface in compliance with DIN 1835 B, above 25 mmshank Ø with 2 driving faces.
ßTypeShort type, 6-8 flutes. With eccentric relief. Straightshank with driving face in compliance with DIN 1835B. Multi-fluted milling cutters, free in centre on face.Right-hand helix 30°.
ApplicationFor standard up to high-strength materials.
ßType Short, right-hand cut, right-hand helix approx. 42°,2 cutting blades, centre cut, straight shank withdriving face in compliance with DIN 1835 B. ApplicationFor soft through ductile and long-chipping materials such as aluminium and copper alloys.
16134Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics
110 85 90 65 55 50 36 28 22 - - - - 18 13 - 38 -
ß Cutting
eng/OP www.hhw.de 16.19
1End Milling Cutters
ßTypeRight-hand cut, right-hand helix approx. 35°, 3flutes. Centre cut. With eccentric relief. Withstraight shank with driving face and clampingsurface in compliance with DIN 1835 B.ApplicationFor soft through ductile, long-chipping materialssuch as aluminium and copper alloys.QualityHSS-E (Co8).
16158Short type.
16161Long type.
16158
16161
16158 - 16161
short long short longd1 e8 d2 h6 l2 l1 l2 l1 16158 … 16161 …
mm mm mm mm mm mm3,0 6 8 52 12 56 201 2014,0 6 11 55 19 63 202 2025,0 6 13 57 24 68 203 2036,0 6 13 57 24 68 204 2048,0 10 19 69 38 88 205 205
ßTypeShort, with face radius, right-hand cut, right-handhelix bis 6,0 mm Ø 40°, starting at 8,0 mm Ø 30°. 2 cutting blades, centre cut, radius tolerance +/-0,04 mm. Straight shank with driving face incompliance with DIN 1835 B. Advantage:No radially ground land, therefore better support andfree cut.QualityHSS-E (Co8).
• Radius Milling Cutters • Roughing End Milling Cutters
www.hhw.de16.20
1 Radius Milling Cutters
0TypeLong, with face radius, right-hand cut, right-handhelix approx. 30°. 2 flutes, centre cut, radiustolerance +/- 0,04 mm. Straight shank with drivingface in compliance with DIN 1835 B.
mm mm mm mm16,0 32 92 16 208 20818,0 32 92 16 209 20920,0 38 104 20 210 21022,0 38 104 20 211 21125,0 45 121 25 212 212
16183
16185
16177Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics
100 90 90 80 65 65 45 30 - - - - - 30 20 - 65 -
16176Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics
70 60 60 50 40 40 30 20 - - - - - 20 15 10 40 -
HSS-ETiAIN
HSS-ETiAIN
16185Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics
100 90 90 80 65 65 45 30 - - - - - 30 20 - 65 -
16183Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics
70 60 60 50 40 40 30 20 - - - - - 20 15 10 40 -
Z 2
Z 3
ß Cutting
eng/OP www.hhw.de 16.21
1Roughing End Milling Cutters
ßTypeShort type, right-hand cut, right-hand helix approx.30°. 4-6 flutes, centre cut up to Ø 20 mm, abovethat free in centre. Straight shank with driving face incompliance with DIN 1835 B. With eccentric relief.
16198Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics
100 90 90 80 65 65 45 30 - - - - - 30 20 - 65 -
16195Al<10%Si Al>10%Si Cu St<520N St<750N St<900N St<1100N St<1200N St<1400N <45HRC <55HRC <60HRC <67HRC VA-steel<900N VA-steel>900N Ti alloys GG(G) plastics
70 60 60 50 40 40 30 20 - - - - - 20 15 10 40 -
HSS-ETiAIN
Roughing End Milling Cutters
ßTypeLong, right-hand cut, with roughing teeth, right-handhelix approx. 30°. 4-6 flutes, straight shank withdriving face in compliance with DIN 1835 B. Witheccentric relief, starting at Ø 10,0 mm, with doublerelief.
QualityHSS-E (Co5). 16200
d1 k12 l2 l1 d2 h6 Z 16200 …mm mm mm mm8,0 38 88 10 4 100
• Radius Milling Cutters • Roughing End Milling Cutters
www.hhw.de16.22
1
Roughing End Milling Cutters
ßTypeExtra long, right-hand cut, right-hand helix approx.30°. 4-5 flutes, straight shank with driving face incompliance with DIN 1835 B.
QualityHSS-E/TiAlN.
d1 l2 l1 d2 Z 16209 …mm mm mm mm6,0 56 100 6 4 1068,0 70 115 10 4 108
10,0 75 121 10 4 11012,0 85 130 12 4 112
d1 l2 l1 d2 Z 16209 …mm mm mm mm16,0 90 145 16 4 11620,0 110 180 20 4 12025,0 125 200 25 5 125
16209
16209
Roughing End Milling Cutters
ßType Short type, right-hand cut, right-hand helix approx.30°. 4-6 cutting blades, centre cut. With straightshank with driving face and clamping surface incompliance with DIN 1835 B. Application For Inox-steel, standard steel with a strength of upto 1200 N/mm2, pure titaniumium, annealedtitaniumium alloys, high-temperature alloys.
Note:Optimised wear resistance thanks to an even distribu-tion of forces at the knurl.
Quality HSS-E-PM/TiCN- coated.
d1 l2 l1 d2 h6 Z 16203 …mm mm mm mm6,0 13 57 6 4 1018,0 19 69 10 4 103
ßTypeSpecial (Long Fellow), right-hand cut, right-handhelix approx. 35°. 4-5 flutes, centre cut. Straightshank with driving face in compliance with DIN 1835 B.
QualityHSS-E (Co8).
16207
16207
d1 l2 l1 d2 l3 d3 Z 16207 …mm mm mm mm mm mm10,0 22 95 10 55 8 4 11012,0 22 100 12 55 10 4 11212,0 26 125 12 80 10 4 11316,0 32 123 16 75 14 4 11616,0 32 138 16 90 14 4 117
d1 l2 l1 d2 l3 d3 Z 16207 …mm mm mm mm mm mm20,0 40 130 20 80 18 4 12020,0 40 150 20 100 18 4 12120,0 40 185 20 135 18 4 12225,0 50 166 25 110 23 5 12525,0 50 196 25 140 23 5 126
TypeShort type, 4-6 flutes. With eccentric relief. Straightshank with driving face and clamping surface incompliance with DIN 1835B, fine roughing profile,right-hand cut with centre cut. Right-hand helixapprox. 35°.
16260ß
QualityHSS-E (Co8).
16262ß
QualityHSS-E (Co8)/TiAlN-coated.
16268ß
Application Also suitable for dry machining. Quality HSS-powder steel/TiAlN- coated
ßTypeMedium length, 4-6 flutes, centre cut. Witheccentric relief. With straight shank with driving faceand clamping surface in compliance with DIN 1835 B, right-hand cut, right-hand helix 35°
QualityHSS-E-PM/TiAlN-coated.
d1 h10 l2 l1 d2 h6 Z 16271 …mm mm mm mm6,0 19 63 6 4 1048,0 28 78 10 4 106
ßTypeLong type, 3-6 flutes, centre cut up to Ø 20 mm,above that free in centre. Straight shank with drivingface in compliance with DIN 1835 B, fine roughingprofile, right-hand helix 30°.
The HHW colour-coding system enables you to see at once which tool is suitable for which material. In most sections of the catalogue, HHW provides you with additional information and data for the respective tool.
The HHW colour-coding system is structured logically and in accordance with the steel key system.
This means, you can choose your tools before the start of the project and therefore you will save time and money.
ßTypeStraight shank with driving face in compliance withDIN 1835 B. Right-hand cut, staggered teeth, cuttingon circumference, 6-12 flutes.
ApplicationFor milling flutes for woodruff keys in compliancewith DIN 6888.QualityHSS-E (Co5)
16375
d1 h12 x l2 e8 for woodruff keys l1 d2 h6 Z 16375 …mm width x height mm mm mm
10,5 x 2,0 2,0 x 3,7 50 6 8 10410,5 x 2,5 2,5 x 3,7 50 6 8 10510,5 x 3,0 3,0 x 3,7 50 6 6 10613,5 x 3,0 3,0 x 5,0 56 10 6 107
*13,5 x 2,0 - 56 10 6 12513,5 x 4,0 4,0 x 5,0 56 10 6 10816,5 x 3,0 3,0 x 6,5 56 10 6 10916,5 x 4,0 4,0 x 6,5 56 10 6 11016,5 x 5,0 5,0 x 6,5 56 10 6 11119,5 x 4,0 4,0 x 7,5 63 10 8 112
*19,5 x 3,0 - 63 10 8 12619,5 x 5,0 5,0 x 7,5 63 10 8 11319,5 x 6,0 6,0 x 7,5 63 10 8 11422,5 x 5,0 5,0 x 9,0 63 10 8 115
*22,5 x 4,0 - 63 10 8 12722,5 x 6,0 6,0 x 9,0 63 10 8 11622,5 x 8,0 8,0 x 9,0 63 10 8 11725,5 x 6,0 6,0 x 10,0 63 10 10 118
*25,5 x 5,0 - 63 10 10 12828,5 x 6,0 6,0 x 11,0 63 10 10 11928,5 x 8,0 8,0 x 11,0 63 10 10 120
28,5 x 10,0 10,0 x 11,0 71 12 10 12132,5 x 8,0 8,0 x 13,0 71 12 12 122
*32,5 x 6,0 - 71 12 10 12932,5 x 10,0 10,0 x 13,0 71 12 12 123*38,5 x 8,0 - 71 12 10 13045,5 x 10,0 10,0 x 16,0 71 12 12 124
* not DIN 850
16375
T-slot milling cutters
ßTypeType N. 6-8 flutes. Right-hand cut, staggered teeth,cutting on circumference and at end. Straight shankwith driving face in compliance with DIN 1835 B.
ApplicationFor milling T-slots in compliance with DIN 650.QualityHSS-E (Co5)
16370
for T-slots d1 d11 l2 d11 l1 d2 h6 Z 16370 …Nominal size mm mm mm mm
ßTypeConcave (quarter circle cutter), straight shank withdriving face in compliance with DIN 1835 B. Right-hand cut, 4 flutes.ApplicationFor materials with a strength of up to approx. 1000 N/mm2.
ßTypeShort type, right-hand cut, right-hand helix approx.30°. 4-6 cutting blades. With eccentric relief.Morse taper shank with inside draw-in thread DIN228 shape A/DIN 2207. Up to 30 mm Ø = DIN 845 B, starting at 30 mm Ø = DIN 845 C.
Al long-chipping Al short-chipping Cu long-chipping Cu short-chipping Mg St<520N St<750N St<900N St<1100N St<1200N St<1400N VA-steel<900N Ti<950N Ti<1400N Thermoplastic Thermosetting plastic350-700 280-560 140-420 105-175 105-140 - - - - - - - - - - -
Solid Carbide Mini Milling Cutters
ßTypeShort, right-hand cut, 3 flutes, right-hand helixapprox. 30°, centre cut, eccentric relief, straightshank with driving face similar to DIN 6535 HB.
Note:Regrinding milling cutters with low flute diameters isuneconomical. For that reason, it is cheaper to usethe milling cutters up to the wear limit and then tothrow them away. You are always using brand newmilling cutters and are reducing the risk of rejecti-ons.
Note:AluCC-coating: extremely close to contour coating of sharp flutes, high toughness at very high hard-ness, self-lubricating: low tendency of cold welding/build-up edges, extremely smooth surface forunproblematic chip removal in the flutes duringmilling and drilling, low friction of the guiding lands(high surface quality of boreholes), possibility ofhigh-quality recoating.
0TypeWith undercut. 2 cutting blades. 45° right-handcut. Centre cut, sharp edge. With clamping surfacein compliance with DIN 6535 HB.ApplicationShort-chipping aluminium, non-ferrous metals, VA-steel.
QualitySolid carbide finest grit AluCC-coated.
Note:AluCC-coating: extremely close to contour coating ofsharp flutes, high toughness at very high hardness,self-lubricating: low tendency of cold welding / build-up edges, extremely smooth surface for an unpro-blematic chip removal in the flutes during milling anddrilling, low friction of the guiding lands (highsurface quality of the boreholes), possibility of high-quality recoating.
Note:AluCC-coating: extremely close to contour coating of sharp flutes, high toughness at very high hard-ness, self-lubricating: low tendency of cold welding/build-up edges, extremely smooth surface forunproblematic chip removal in the flutes duringmilling and drilling, low friction of the guiding lands(high surface quality of boreholes), possibility ofhigh-quality recoating.
Z 3
16528Al long-chipping Al short-chipping Cu long-chipping Cu short-chipping Mg St<520N St<750N St<900N St<1100N St<1200N St<1400N VA-steel<900N Ti<950N Ti<1400N Thermoplastic Thermosetting plastic
1 SC end milling cutter AluSpeed® with edge chamfer
0TypeWith undercut. 3 flutes, with edge chamfer (f). 45°right-hand cut. Centre cut.
16530 201-221TypeWith clamping surface in compliance with DIN 6535HB.
16530 302-321TypeWith smooth straight shank in compliance with DIN6535 HA.ApplicationSoft materials, long-chipping aluminium, non-ferrousmetals, plastics.QualitySolid carbide finest grit with mirror finish,polished chip compartment for improved chipremoval.
Note:Mirror finish: highest cutting edge profiling =extremely sharp flutes, improved removal of thechip, reduction of cold welding.
16531 202-221TypeWith clamping surface in compliance with DIN 6535 HB.
16531 302-321TypeWith smooth straight shank in compliance with DIN 6535 HA.ApplicationShort-chipping aluminium, non-ferrous metals, VA-steel.QualitySolid carbide finest grit AluCC-coated.
Note:AluCC-coating: extremely close to contour coating of sharp flutes, high toughness at very high hard-ness, self-lubricating: low tendency of cold welding/build-up edges, extremely smooth surface for anunproblematic chip removal in the flutes duringmilling and drilling, low friction of the guiding lands(high surface quality of the boreholes), possibility ofhigh-quality recoating.
ßType 4 flutes, centre cut, right-hand helix, uneven ( 35/38°). Optimised chip compartment. Up to 80 %longer service life. Up to 60 % better feed. Roughingand finishing with a single tool. Vibration-free.Application Uneven pitch for smooth, low-vibration operationand high surface quality. High machining perfor-mance.Quality Multi-purpose carbide quality finest grit (P 20 - K 40) TiAlN-coated. Type VA-steel: Nacro-coated.
16533
16534 104-120
16534 204-225
16534 304-320
short short/6535HBd1 l2 l1 d2 16533 …
mm mm mm mm4,0 8 54 6 1045,0 9 54 6 1056,0 10 54 6 1067,0 12 58 8 1078,0 12 58 8 1089,0 14 66 10 109
SC end milling cutter 35/38° G2 with shank with clamping surface
ßType Long type, 4 cutting blades, centre cut, right-hand helix with uneven graduation 35/38°.Optimised chip compartment. With straight shankwith driving face and clamping surface in complian-ce with DIN 6535 HB. Up to 80 % longer service life.Up to 60 % better feed. Roughing and finishing witha single tool. Vibration-free.
Application For materials with a hardness of up to HRC 52.Uneven pitch for smooth, low-vibration operationand high surface quality. High machining perfor-mance. Quality Multi-purpose carbide quality finest grit (P 20 - K 40) TiAlN-coated.
SC end milling cutter 35/38° G2 with internalcoolant feedTypeType H, long. Straight shank with driving face incompliance with DIN 6535 HB. 4 flutes, centre cut,right-hand helix, uneven (35/38°). Optimised chipcompartment. Up to 80 % longer service life. Up to 60 % better feed. Roughing and finishing witha single tool. Vibration-free.ApplicationFor materials with a hardness of up to HRC 52.Uneven pitch for smooth, low-vibration operationand high surface quality. High machining perfor-mance.Quality Multi-purpose carbide quality finest grit (P 20 - K 40) TiAlN-coated.
16538 201-320
0SC end milling cutter 35/38° AluCCApplicationMilling of aluminium, non-ferrous metals, high-alloyed and stainless tool steel.QualitySolid carbide finest grit AluCC-coated.
SC end milling cutter 35/38° G2 with corner radius
16540 101-137
ßTypeTyp H, long. Straight shank with driving face incompliance with DIN 6535 HB. 4 flutes, centre cut,right-hand helix, uneven (35/38°). Optimised chipcompartment. Up to 80 % longer service life. Up to60 % better feed. Roughing and finishing with asingle tool. Vibration-free.
ApplicationFor materials with a hardness of up to HRC 52.Uneven pitch for smooth, low-vibration operationand high surface quality. High machining perfor-mance. Quality multi-purpose carbide quality finest grit (P 20 - K 40) TiAlN-coated.
ßType Right-hand cut, straight shank with driving face incompliance with DIN 6535 HB. Right-hand helixapprox. 45°, 6-8 cutting blades.ApplicationFor circumference milling as finishing working stepfor producing highest surface quality (face cuttingonly at low cutting depths).
ßType Right-hand cut, straight shank with driving face incompliance with DIN 6535 HB. Right-hand helixapprox. 45°, eccentric relief for better cutting edges,6-8 flutes.ApplicationFor circumference milling as the finishing workingstep for the production of a high quality surface.Especially suitable for machining deep and/or hard-to-reach places.
ßTypeWith ground-in chip breakers, centre cut,30°-spiral for high roughing performance. With straight shank with driving face in compliancewith DIN 6535 HB.ApplicationFor roughing and finishing steel with extreme feeds.Very smooth and quiet running due to the reductionof the cutting load by means of the special chipbreakers.
ßType Long type, 4 flutes, centre cut, right-hand helixapprox. 25°. Fine knurl profile. Straight shank withdriving face in compliance with DIN 6535 HB. Application For materials with a hardness of up to HRC 45.Very high machining performance thanks toroughing teeth. Universal use, also suitable for
mm mm mm mm3,0 6 57 6 1014,0 8 57 6 1025,0 10 57 6 1036,0 13 57 6 1048,0 16 63 8 105
DIN 6535 HBd1 h10 l2 l1 d2 h6 16567 …
mm mm mm mm10,0 22 72 10 10612,0 26 83 12 10716,0 32 92 16 10820,0 38 104 20 109
16567
SC roughing end milling cutter with ICF
ßType Long, centre cut, right-hand helix 25°. Withinternal coolant feed in the cutting flute, fine knurlprofile. Straight shank with driving face in complian-ce with DIN 6535 HB.
Application For materials with a hardness of up to HRC 45.Multi-purpose use. The coolant is guided directly tothe flutes. This results in long service life andcomplete removal of the chips. This is very impor-tant when milling into solid material or milling ofpockets.
16569
DIN 6535 HBd1 h10 l2 l1 d2 h6 16569 …
mm mm mm mm6,0 13 57 6 1018,0 16 63 8 102
10,0 22 72 10 103
DIN 6535 HBd1 h10 l2 l1 d2 h6 16569 …
mm mm mm mm12,0 26 83 12 10416,0 32 92 16 10520,0 38 104 20 106
16569
Solid Carbide Deburrers 90°
ßTypeShort type, 4-6 flutes. With reinforced straightshank with driving face in compliance with DIN 6535HB (with Weldon). Ø 4 mm with smooth straightshank in compliance with DIN 6535 HA.QualitySolid carbide K20 Micrograin/TiAlN-coated.
ßTypeShort type, 4-6 flutes. With reinforced straightshank with driving face in compliance with DIN 6535HB (with Weldon). Ø 4 mm with smooth straightshank in compliance with DIN 6535 HA.
mm mm mm12,0 83 12 6 105 10516,0 92 16 6 106 10620,0 104 20 6 107 107
16573
16572 - 16573
Solid carbide two-way deburrers
ßType 4 flutes, 45°. With smooth straight shank incompliance with DIN 6535 HA. Application For deburring in both directions as well as bevelling.
16583
DIN 6535 HAd1 h10 l2 l1 d2 h6 16583 …
mm mm mm mm4,0 2 100 6 1016,0 2 100 6 1028,0 2 100 6 103
DIN 6535 HAd1 h10 l2 l1 d2 h6 16583 …
mm mm mm mm10,0 4 100 6 10412,0 4 100 6 10516,0 5 100 10 106
16583
Solid Carbide Keyway Milling Cutters
ßTypeShort type, 2 flutes, point angle 90° (+/– 1°), 25° right-hand helix, straight shank shape A.ApplicationA new concept of shank cutting tools for multipleuse applications. Allows up to 8 operations with onesingle tool.
QualitySolid carbide.
Note:d1 3-10 mm = h9,d1 12-20 mm = d9.
16580
(1) (2) (3) (4) (5) (6) (7) (8)
Solid carbided1 l1 l2 d2 h6 16580 …
mm mm mm mm3,0 50 6 4 1014,0 50 8 5 1025,0 50 10 6 1036,0 60 12 8 1048,0 70 16 10 105
Solid carbided1 l1 l2 d2 h6 16580 …
mm mm mm mm10,0 70 18 12 10612,0 70 20 12 10716,0 80 26 16 10820,0 100 32 20 109
Heavy-duty machining is the machining of hardened materials with a hardness of 52 - 65 HRC. Advantages are reduced costs and shorter machining times which may be achieved with heavy-duty milling. Special HSC milling strategies, high surface quality and the elimination of quench distortion make this procedure an interesting possibilty for an ever-growing market. Additional advantages are: workingsteps such as multiple clamping and time-consuming polishing are no longer necessary, saving great amounts of money - cost benefit for yourproduction!
We have designed our ATORN programme with these machining process in mind. In terms of selection, material and geometry, this programmeleaves nothing to be desired. It is geared towards extremely high requirements.
The ATORN heavy-duty milling tools offer you the best conditions for an efficient heavy-duty machining. Different geometries have beenperfectly adapted to different milling procedures. The carbide used stands out because of its high hardness and extreme toughness.
A special edge treatment and new coatings RockTec 52 and RockTec 65 result in longest service life of ATORN tools.
RockTec 52Multi-purpose use: up to 52 HRCTolerance radius correction: +/- 0,01 mmCoating: monolayerMicro hardness: 3300 HVMax. temperature: < 900 °CFor wet and dry milling
RockTec 65For HPC and HSC milling: up to 65 HRCTolerance radius correction: +/- 0,01 mmCoating: new multilayerMicro hardness: 3600 HVMax. temperature: < 1200 °CLongest service life for dry milling
The expansive programme which satisfies the highest requirements
0TypeWith undercut. 3 cutting blades cutting up to thecentre. 30° right-hand helix. With clamping surfacein compliance with DIN 6535 HB. Best chip removalthanks to extremely smooth surface.QualitySolid carbide Ultra-finest grit/TiAlN-Ultra-coated.
16607
16607
DIN 6535 HBd1 e8 d2 h5 d3 l1 l2 l3 b x 45° 16607 …
The HHW colour-coding system enables you to see at once which tool is suitable for which material. In most sections of the catalogue, HHW provides you with additional information and data for the respective tool.
The HHW colour-coding system is structured logically and in accordance with the steel key system.
This means, you can choose your tools before the start of the project and therefore you will save time and money.
0TypeShort type, with undercut, 4 cutting bladescutting up to the centre. 30° right-hand helix. Bestchip removal thanks to extremely smooth surface.QualitySolid carbide Ultra-finest grit/TiAlN-Ultra-coated.
16610 102-104TypeWithout undercut, with smooth straight shank in compliance with DIN 6535 HA.
16610 105TypeWith undercut and smooth straight shank incompliance with DIN 6535 HA.
16610 106-120TypeWith undercut and clamping surface in compliancewith DIN 6535 HB.
ßTypeLong and extra long, 8-16 flutes, right-hand spiralflute, right-hand cut, does not cut across its centre.With straight shank with driving face in compliancewith DIN 6535 HA, right-hand helix approx. 50°.ApplicationTool steel with a hardness of up to HRC 64 in drymachining.
d1 f8 l2 l1 d2 h6 Z 16614 …mm mm mm mm6,0 13 57 6 8 201
L 6,0 18 62 6 8 2028,0 19 63 8 10 203
L 8,0 24 68 8 10 20410,0 22 72 10 12 205
L 10,0 30 80 10 12 20612,0 26 83 12 12 207
L 12,0 36 93 12 12 208
d1 f8 l2 l1 d2 h6 Z 16614 …mm mm mm mm16,0 32 92 16 16 211
L16,0 48 108 16 16 212XL 16,0 65 125 16 16 213
XXL 16,0 95 150 16 16 214L 20,0 60 126 20 16 218
XL 20,0 75 135 20 16 219XXL 20,0 95 150 20 16 220
The HHW colour-coding system
The HHW colour-coding system enables you to see at once which tool is suitable for which material. In most sections of the catalogue, HHW provides you with additional information and data for the respective tool.
The HHW colour-coding system is structured logically and in accordance with the steel key system.
This means, you can choose your tools before the start of the project and therefore you will save time and money.
0TypeShort, with undercut. 6 -8 cutting blades cuttingup to the centre. 45° right-hand helix. With clampingsurface in compliance with DIN 6535 HB. Best chipremoval thanks to extremely smooth surface.QualitySolid carbide Ultra-finest grit/TiAlN-Ultra-coated.
16616
d1 e8 d2 h5 d3 l1 l2 l3 Z 16616 …mm mm mm mm mm mm4,0 6 3,7 57 19 11 6 2015,0 6 4,7 57 19 13 6 2026,0 6 5,7 57 19 13 6 2038,0 8 7,7 63 25 19 6 204
ßTypeLong type, right-hand cut, 4 flutes, right-hand helix,centre cut. Radius tolerance +/– 0,02 mm. With clamping surface in compliance with DIN 6535 HB.
ßTypeLong type, right-hand cut, 2 flutes, right-hand helix,centre cut. Radius tolerance +/– 0,02 mm. With clamping surface in compliance with DIN 6535 HB.
ßType Extra long type, 2 flutes, centre cut. Spherical upto 220°, increased true-running accuracy. With smoothstraight shank in compliance with DIN 6535 HA. Application For heavy-duty machining, 3D-profile milling of high-strength materials and for milling of hardened steelwith a hardness of up to HRC 65.
ßType 4 cutting blades, straight flute. With smooth straightshank in compliance with DIN 6535 HA. Radiustolerance +/– 0,01 mm.
Application For materials with a hardness of up to HRC 45.For rounding and deburring of edges and contours.For high-strength materials as well as for aluminiumand non-ferrous metals.QualityMulti-purpose carbide quality finest grit (P 20 - K 40) TiAlN-coated.
Solid Carbide Roughing End Milling Cutters Quickmax
ßType Short type, 3 -6 flutes, centre cut. Right-handhelix 45°. Great cutting capacity. With protectivechamfer, special roughing profile. Long service life.Quick chip removal. Extremely sturdy cutting edges.Great stability. Application Alloyed steel, stainless steel, titaniumium, Inconel.
ßTypeLong type, fine roughing profile,right-hand cut, 3-4flutes, right-hand helix, centre cut. Radius toleran-ce +/– 0,02 mm. With clamping surface in complian-ce with DIN 6535 HB.QualityMulti-purpose carbide quality finest grit(P 20 - K 40) TiAlN-coated.
16631
d1 e8 l2 l1 d2 h6 Z 16631 …mm mm mm mm6,0 16 57 6 3 2018,0 16 63 8 3 202
ßTypeWith clamping surface in compliance with DIN 6535HB. Long, right-hand cut, 2 flutes, with cornerradius (1).QualityMulti-purpose carbide quality finest grit (P 20 - K 40) TiAlN-coated.
16633
d1 e8 l2 l1 d2 16633 …mm mm mm mm6 x R 0,5 20 60 6 1016 x R 1 20 60 6 1028 x R 0,5 25 70 8 1038 x R 1 25 70 8 1048 x R 1,5 25 70 8 1058 x R 2 25 70 8 10610 x R 0,5 30 90 10 107
d1 e8 l2 l1 d2 16633 …mm mm mm mm10 x R 1 30 90 10 10810 x R 1,5 30 90 10 10910 x R 2 30 90 10 11012 x R 0,5 30 90 12 11112 x R 1 30 90 12 11212 x R 1,5 30 90 12 11312 x R 2 30 90 12 114
d1 e8 l2 l1 d2 16637 …mm mm mm mm6 x R 0,5 20 60 6 1016 x R 1 20 60 6 1028 x R 0,5 25 70 8 1038 x R 1 25 70 8 1048 x R 1,5 25 70 8 1058 x R 2 25 70 8 10610 x R 0,5 30 90 10 107
d1 e8 l2 l1 d2 16637 …mm mm mm mm10 x R 1 30 90 10 10810 x R 1,5 30 90 10 10910 x R 2 30 90 10 11012 x R 0,5 30 90 12 11112 x R 1 30 90 12 11212 x R 1,5 30 90 12 11312 x R 2 30 90 12 114
60Z 3-4
Z 2
Z 4
(1)
ß Cutting
eng/OP www.hhw.de 16.65
1Solid Carbide Torus Milling Cutters
0TypeWith undercut. 2 cutting blades cutting acrossthe centre. 20° right-hand helix. With smoothstraight shank in compliance with DIN 6535 HA.Best chip removal thanks to extremely smoothsurface.QualitySolid carbide Ultra-finest grit/TiAlN-Ultra-coated.
16634 101-106
16634 165-180
d1 e8 R l1 l2 AP d2 h5 d3 16634 …mm mm mm mm mm mm mm
ßTypeLong, with corner radius (1). Right-hand helixapprox. 45°. With clamping surface in compliancewith DIN 6535 HB. ApplicationFor circumference milling as finishing working stepfor producing highest surface quality (face cuttingonly at low cutting depths).
10 x R 0,5 22 100 10 20310 x R 1,0 22 100 10 20412 x R 0,5 26 110 12 20512 x R 1,0 26 110 12 20616 x R 1,0 32 130 16 20716 x R 1,5 32 130 16 20820 x R 1,0 38 140 20 20920 x R 1,5 38 140 20 21020 x R 2,0 38 140 20 211
1 Solid Carbide Micro Milling Cutters for Graphite
ßType2 flutes, right-hand helix with corner radius,centre cut, with smooth straight shank in complian-ce with DIN 6535 HA.Tolerance d1: 0/-0,015 mm.Accuracy of shape: radius +/- 0,007 mm.True-running accuracy: 0,005 mm.ApplicationMilling tools for machining of graphite electrodesand green compacts.QualitySolid carbide, with diamond coating.
1Solid Carbide Micro Radius Milling Cutters for Graphite
ßType2 flutes, right-hand helix, centre cut, with smoothstraight shank in compliance with DIN 6535 HA.Tolerance d1: 0/-0,015 mm.Accuracy of shape: radius +/- 0,007 mm.True-running accuracy: 0,005 mm.ApplicationMilling tools for machining of graphite electrodesand green compacts.
Type Double flute (cat.-no. 16750 139-152 single flute).Clamping shank 6 mm. Pilot hardened.
Application For edge and contour deburring machines. Rake angle 0° for short-chipping, hard materials. Rake angle 6° for strength-hard materials. Rake angle 12° for ductile up to soft materials. Rake angle 30° for soft materials.
Quality Universal carbide quality finest grit.
16750
Type Application / Type D x L Point angle/ flutes Rake angle Coating 16750 …mm Radius
1 with revolving pilot (Ø 2,5 mm) 6 x 34 90 ° 4 0° – 1011 with revolving pilot (Ø 2,5 mm) 6 x 34 90 ° 4 0° TiAIN 1022 with ball bearing-mounted roller (Ø 3,0 mm) 6 x 34 90 ° 4 0° – 1032 with ball bearing-mounted roller (Ø 3,0 mm) 6 x 34 90 ° 4 0° TiAIN 1042 with ball bearing-mounted roller (Ø 4,0 mm) 6 x 34 90 ° 4 0° – 1052 with ball bearing-mounted roller (Ø 4,0 mm) 6 x 34 90 ° 4 0° TiAIN 1061 with revolving pilot (Ø 2,5 mm) 6 x 34 90 ° 6 0° – 1071 with revolving pilot (Ø 2,5 mm) 6 x 34 90 ° 6 0° TiAIN 1082 with ball bearing-mounted roller (Ø 3,0 mm) 6 x 34 90 ° 6 0° – 1092 with ball bearing-mounted roller (Ø 3,0 mm) 6 x 34 90 ° 0 6° TiAIN 1102 with ball bearing-mounted roller (Ø 4,0 mm) 6 x 34 90 ° 6 0° – 1112 with ball bearing-mounted roller (Ø 4,0 mm) 6 x 34 90 ° 6 0° TiAIN 1121 with revolving pilot (Ø 2,5 mm) 6 x 34 90 ° 4 6° – 1131 with revolving pilot (Ø 2,5 mm) 6 x 34 90 ° 4 6° TiAIN 1142 with ball bearing-mounted roller (Ø 3,0 mm) 6 x 34 90 ° 6 6° – 1152 with ball bearing-mounted roller (Ø 3,0 mm) 6 x 34 90 ° 6 6° TiAIN 1162 with ball bearing-mounted roller (Ø 4,0 mm) 6 x 34 90 ° 6 6° – 1172 with ball bearing-mounted roller (Ø 4,0 mm) 6 x 34 90 ° 6 6° TiAIN 1181 with revolving pilot (Ø 2,5 mm) 6 x 34 90 ° 4 12° – 1191 with revolving pilot (Ø 2,5 mm) 6 x 34 90 ° 4 12° TiAIN 1201 with revolving pilot (Ø 2,5 mm) 6 x 34 90 ° 3 12° TiAIN-aluminium 1212 with ball bearing-mounted roller (Ø 3,0 mm) 6 x 34 90 ° 4 12° – 1222 with ball bearing-mounted roller (Ø 3,0 mm) 6 x 34 90 ° 12 4° TiAIN 1232 with ball bearing-mounted roller (Ø 3,0 mm) 6 x 34 90 ° 3 12° TiAIN-aluminium 1242 with ball bearing-mounted roller (Ø 4,0 mm) 6 x 34 90 ° 4 12° – 1252 with ball bearing-mounted roller (Ø 4,0 mm) 6 x 34 90 ° 12 4° TiAIN 1262 with ball bearing-mounted roller (Ø 4,0 mm) 6 x 34 90 ° 3 12° TiAIN-aluminium 1273 with revolving pilot (Ø 2,5 mm) 6 x 34 90 ° 3 30° – 1283 with revolving pilot (Ø 2,5 mm) 6 x 34 90 ° 3 30° TiAIN 1293 with revolving pilot (Ø 2,5 mm) 6 x 34 90 ° 3 30° TiAIN-aluminium 1303 with ball bearing-mounted roller (Ø 3,0 mm) 6 x 34 90 ° 3 30° – 1313 with ball bearing-mounted roller (Ø 3,0 mm) 6 x 34 90 ° 3 30° TiAIN 1323 with ball bearing-mounted roller (Ø 3,0 mm) 6 x 34 90 ° 3 30° TiAIN-aluminium 1333 with ball bearing-mounted roller (Ø 4,0 mm) 6 x 34 90 ° 3 30° – 1343 with ball bearing-mounted roller (Ø 4,0 mm) 6 x 34 90 ° 3 30° TiAIN 1353 with ball bearing-mounted roller (Ø 4,0 mm) 6 x 34 90 ° 3 30° TiAIN-aluminium 1364 with ball bearing-mounted roller (Ø 4,0 mm) 10 x 34 90 ° 6 0° – 1374 with ball bearing-mounted roller (Ø 4,0 mm) 10 x 34 90 ° 6 0° TiAIN 1384 with ball bearing-mounted roller (Ø 5,0 mm) 10 x 34 90 ° 6 0° – 1394 with ball bearing-mounted roller (Ø 5,0 mm) 10 x 34 90 ° 0 6° TiAIN 1404 with ball bearing-mounted roller (Ø 4,0 mm) 10 x 34 90 ° 3 6° – 1414 with ball bearing-mounted roller (Ø 4,0 mm) 10 x 34 90 ° 6 3° TiAIN 1424 with ball bearing-mounted roller (Ø 5,0 mm) 10 x 34 90 ° 3 6° – 1434 with ball bearing-mounted roller (Ø 5,0 mm) 10 x 34 90 ° 6 3° TiAIN 1445 with ball bearing-mounted roller (Ø 4,0 mm) 10 x 34 90 ° 3 30° – 1455 with ball bearing-mounted roller (Ø 4,0 mm) 10 x 34 90 ° 3 30° TiAIN 1465 with ball bearing-mounted roller (Ø 4,0 mm) 10 x 34 90 ° 3 30° TiAIN-aluminium 1475 with ball bearing-mounted roller (Ø 5,0 mm) 10 x 34 90 ° 3 30° – 1485 with ball bearing-mounted roller (Ø 5,0 mm) 10 x 34 90 ° 3 30° TiAIN 1495 with ball bearing-mounted roller (Ø 5,0 mm) 10 x 34 90 ° 3 30° TiAIN-aluminium 1506 with ball bearing-mounted roller (Ø 3,0 mm) 6 x 34 R 0,5 mm 3 0° – 1516 with ball bearing-mounted roller (Ø 3,0 mm) 6 x 34 R 1,0 mm 3 0° – 1526 with ball bearing-mounted roller (Ø 3,0 mm) 6 x 34 R 1,5 mm 3 0° – 1537 with ball bearing-mounted roller (Ø 4,0 mm) 10 x 34 R 2,0 mm 4 0° – 1547 with ball bearing-mounted roller (Ø 4,0 mm) 10 x 34 R 2,5 mm 4 0° – 1557 with ball bearing-mounted roller (Ø 4,0 mm) 10 x 34 R 3,0 mm 4 0° – 1568 for machining with guiding slide or similar 6 x 40 90 ° 3 0° – 1578 for machining with guiding slide or similar 6 x 40 90 ° 3 0° TiAIN 158
Type 1 Type 2
Type 3 Type 4
L
d
HH1
D
ß Cutting
eng/OP www.hhw.de 16.71
1Type 5 Type 6
Type 8Type 7
Recommendations for solid carbide form end milling cutters cat.-no. 16750 ++ suitable + limited use steel copper alloys/ stainless steel alloy aluminium alloy plastics
TypeRake angle 8-10°. Each broach comes with bases(e.g. 3 strokes= 2 bases). Supplied in wooden case.ApplicationFor machining keyways in compliance with DIN6885. For cast iron, steel, brass, and aluminium.Specially for use in hand-operated arbor presses.Short broaching time (60seconds), short set-up timeand easy to use. Guide bushes and bases are usedto precisely align keyways with the borehole and todetermine the proper depth.QualityHSS.
16880
Set size for boreholes broach length 16880 …broaches guide bushings Ø (d1) mm Ø mm mm
TypeRake angle 8-10°. Each broach comes with bases(e.g. 3 strokes= 2 bases). Cat.-no. 16881 101 without base. Guide bushings not included (see cat.-no. 16882).ApplicationFor machining keyways in compliance with DIN6885. For cast iron, steel, brass, and aluminium.Specially for use in hand-operated arbor presses.Short broaching time (60 seconds), short set-uptime and easy to use. Guide bushes and bases areused to precisely align keyways with the boreholeand to determine the proper depth.
QualityHSS.
16881
Type b1 b2 l1 l2 l3 h1 h2 keyway depth for boreholes Ø broach length number of strokes tolerance 16881 …mm mm mm mm mm mm mm mm mm mm mm
3 0,787 I 1014 0,965 II 1025 1,270 II 1035 1,194 III 1046 1,448 III 105
Size thickness for type 16883 …mm mm
8 1,879 III 10610 1,422 IV 10712 1,524 IV 10814 1,778 IV 10916 1,549 V 110
Size thickness for type 16883 …mm mm
18 1,587 V 11120 1,587 VI 11222 1,587 VI 11324 1,587 VI 11425 1,587 VI 115
16883
Guide Bushes
TypeHole tolerance H 7. Up to RD III 36 x 65 mm withcollar.ApplicationFor push broaches (keyway broaches) cat.-no.16881.
16882
For type d1 x l1 16882 …mm
RD I 6 x 32 101RD I 7 x 32 102RD I 8 x 32 103RD I 9 x 32 104RD I 10 x 32 105RD II 11 x 46 110RD II 12 x 46 111RD II 13 x 46 112RD II 14 x 46 113RD II 15 x 46 114RD II 16 x 46 115RD II 17 x 46 116RD II 18 x 46 117RD II 19 x 46 118RD III 17 x 65 130RD III 18 x 65 131RD III 19 x 65 132RD III 20 x 65 133RD III 22 x 65 135RD III 24 x 65 137
For type d1 x l1 16882 …mm
RD III 25 x 65 138RD III 26 x 65 139RD III 27 x 65 140RD III 28 x 65 141RD III 30 x 65 142RD III 32 x 65 143RD III 34 x 65 144RD III 35 x 65 145RD III 36 x 65 146RD IV 32 x 102 150RD IV 34 x 102 151RD IV 35 x 102 152RD IV 36 x 102 153RD IV 38 x 102 154RD IV 40 x 102 155RD IV 42 x 102 156RD IV 44 x 102 157RD IV 45 x 127 158RD IV 46 x 127 159RD IV 48 x 127 160
For type d1 x l1 16882 …mm
RD IV 50 x 127 161RD IV 52 x 127 162RD IV 54 x 127 163RD IV 55 x 127 164RD IV 56 x 127 165RD V 52 x 127 175RD V 54 x 127 176RD V 55 x 127 177RD V 56 x 127 178RD V 58 x 127 179RD V 60 x 154 180RD V 62 x 154 181RD V 64 x 154 182RD V 65 x 154 183RD V 66 x 154 184RD V 68 x 154 185RD V 70 x 154 186RD V 72 x 154 187RD VI 70 x 154 193
d1
l1
16882
Size tolerance mass diagonal boreholebroach pressure length broach length broach length 16885 …mm mm mm mm kg mm min. mm max. mm