-
Cutting Tool • Phillips Screwdriver • Socket Set • Grinder
KIT FEATURES• DDIN Head Unit Provision• Stacked ISO DIN Head
Unit Provision
A) DDIN Trim plates
KIT COMPONENTS
TOOLS REQUIRED:A
APPLICATIONSToyota
Rav 4 2001-05 MR2 Spider 2000-03
Celica 2000-05 Echo 2000-05
Highlander 2001-07 Matrix 2005-07
4 Runner (Excluding Limited) 2003-07 Tundra 2003-06Sequoia
2003-07
FJ Cruiser 2007-08Yaris 2007
Scion TC 2005-08 / XA 2004-06 / XB 2004-08 / XD 2008
INSTALLATION INSTRUCTIONS FOR PART CT24TY09
CT24TY09
www.connects2.com
-
TABLE OF CONTENTS
95-8202
Dash DisassemblyToyota Rav 4
2001-2005...............................................................
1Toyota MR2 Spyder 2000-2003
.................................................... 2Toyota Celica
2000-2005
.............................................................
3Toyota Echo 2000-2005
...............................................................
4Toyota Highlander 2001-2006
..................................................... 5Toyota
Matrix 2005-2007
.............................................................
6Toyota 4 Runner (Excluding Limited) 2003-2006
......................... 7Toyota Tundra 2003-2006
.............................................................
8Toyota Sequoia
2003-2006...........................................................
9Toyota FJ Cruiser
2007-2008.......................................................10Yaris
2007....................................................................................11Scion
XA 2004-2006
....................................................................12Scion
XB 2004-2007
....................................................................13Scion
XB 2008
.............................................................................14Scion
TC 2005-2008
..................................................................15Scion
XD 2008
.............................................................................16
Kit AssemblyDouble DIN Head Unit
Provision..................................................
17Stacked ISO DIN Head Unit Provision
......................................... 17
Final Assembly
............................................................................18
-
1
Disconnect the negative battery terminal to prevent an
accidentalshort circuit.
1
Unclip and remove side panel fromboth sides of radio and
climatecontrols. Figure A)
2
TOYOTA RAV 4 2001-2005
Remove (4) Phillips screws securingthe radio/climate control
trim panel.(Figure B)
3
Remove (4) 10 MM bolts securing theradio. (Figure C)
4
DASH DISASSEMBLY
A
B
C
Continue to kit assembly.
Unplug and remove radio.5
Remove factory brackets from radio.Retain brackets for use
during kitassembly.
6
7
-
TOYOTA MR2 SPIDER 2000-2003
Disconnect the negative battery terminal to prevent an
accidentalshort circuit.
Unsnap the lower trim piece fromeach side of the dash console
andremove (2) Phillips screws exposed ineach cavity. Remove the
upper trimpiece from each side of the console.(Figure A)
2
Remove the climate control knobsand (2) Phillips screws
exposed.Remove the climate control trimbezel. (Figure A)
3
Remove the ashtray and (1) 10mmbolt exposed. Unclip the ashtray
trimbezel and remove. (Figure A)
Unclip the radio trim bezel, remove(4) Phillips screws securing
the unitand disconnect the wiring.
4
1
5
2
A
Continue to kit assembly.7
6 Remove factory brackets from radio.Retain brackets for use
during kitassembly.
DASH DISASSEMBLY
-
3
Disconnect the negative battery terminal to prevent an
accidentalshort circuit.
1
Unclip and remove the gear shiftertrim bezel and remove (2)
Phillipsscrews exposed below the climatecontrols. (Figure A)
2
Unclip the climate control/factoryradio trim bezel and
remove.(Figure A)
4
Remove (4) 10mm screws securingthe factory head unit and
disconnectthe wiring.
5
Pull off climate control knobs andremove (2) Phillips screws
exposed.(Figure A)
3
TOYOTA CELICA 2000-2005
A
Continue to kit assembly.7
6 Remove factory brackets from radio.Retain brackets for use
during kitassembly.
DASH DISASSEMBLY
-
Disconnect the negative battery terminal to prevent an
accidentalshort circuit.
1A
4
DASH DISASSEMBLY
TOYOTA ECHO 2000-2005
Remove the climate control knobsand (2) Phillips screws
exposed.Unclip and remove the climate con-trol trim bezel. Depress
the sideclips securing the climate controlpanel and move the panel
to access(2) Phillips screws from the top ofthe factory radio
brackets. (Figure A)
2
Remove the ashtray. Unclip andremove the radio trim bezel.
Remove(2) Phillips screws from the bottomof the radio brackets and
disconnectthe wiring.
3
Continue to kit assembly.5
4 Remove factory brackets from radio.Retain brackets for use
during kitassembly.
-
5
Pull and remove dash panel fromradio and climate controls. Tip:
Thereare 8 clips. (Figure A)
2
Remove (6) 10mm bolts from radioand climate controls
assembly.(Figure B)
3
Remove assembly and disconnectthe wiring.
4
Remove (8) Phillips bolts and (4) Phillipsscrews to separate
brackets from assem-bly. Retain brackets for use duringkit
assembly. (Figure C)
5
A
B
C
DASH DISASSEMBLY
TOYOTA HIGHLANDER 2001-2006
Disconnect the negative battery terminal to prevent an
accidentalshort circuit.
1
Continue to kit assembly.6
-
6
DASH DISASSEMBLY
Disconnect the negative battery terminal to prevent an
accidentalshort circuit.
1
Unclip the bottom edge of the radiotrim panel then lift up and
out toremove. (Figure A)
2
Remove (4) 10 MM bolts securingthe factory radio. (Figure B)
3
A
SCAN
SEEKTRACK
TUNE
AM FM1 FM2 DISK
B
TOYOTA MATRIX 2005-2007
-
7
TOYOTA 4 RUNNER 2003-2006(EXCLUDING LIMITED)
DASH DISASSEMBLY
Disconnect the negative battery ter-minal to prevent an
accidental shortcircuit.Unsnap and remove trim from
aroundshifter.
Unsnap and remove trim covers fromaround center console pocket
edgeat front and rear of console.
1
2
Unsnap and remove entire centerpanel around radio. (Figure
D)
10
Remove (2) 10 mm bolts securingradio.
11
3
Unsnap and remove center consolecover. (Figure A)
4
Unsnap trim ring from around ignitionkey cylinder. Remove (1) 10
mm bolt from bottomright of panel below steering column.Unsnap
panel and pull away to gainaccess behind panel. (Figure B)
5
6
Remove (1) 10 mm bolt on bottomleft of center panel behind
panelbelow steering column. (Figure B)
7
Remove (1) 10 mm bolt beneath cli-mate control behind pocket
door.Unsnap and remove climate control.(Figure C)
8
Remove (2) 10 mm bolts beneathradio behind climate controls.
9
A
B
C
D
12 Unplug and remove radio.
Continue to kit assembly.14
13 Remove factory brackets from radio.Retain brackets for use
during kitassembly.
-
8
Disconnect the negative battery terminal to prevent an
accidentalshort circuit.
1
Remove the (3) climate control knobs bypulling straight outward.
(Figure A)
2
TOYOTA TUNDRA 2003-2006
Remove (3) Phillips screws frombehind knobs. (Figure A)
3
Unclip and remove entire trim panel. (Figure C)
5
6
4
DASH DISASSEMBLY
A
B
D C
7
Position vents facing upward andremove (1) Phillips screw from
eachA/C vent. (Figure B)
Remove (4)10 mm bolts to removeradio. (Figure D)
Unplug and remove radio.
Continue to kit assembly.9
8 Remove factory brackets from radio.Retain brackets for use
during kitassembly.
-
9
Disconnect the negative battery terminal to prevent an
accidentalshort circuit.
1
2
TOYOTA SEQUOIA 2003-2006
Unclip and remove entire radio trimpanel including climate
controls.(Figure B)
3
Remove (4) 10 mm bolts to removeradio. (Figure C)
4
DASH DISASSEMBLY
A
B
C
Continue to kit assembly.
5
Position vents facing upward andremove (1) Phillips screw from
eachA/C vent. (Figure A)
Unplug and remove radio.
7
6 Remove factory brackets from radio.Retain brackets for use
during kitassembly.
-
10
Disconnect the negative battery terminal to prevent an
accidentalshort circuit.
1
Remove two Phillips screws frombottom part of side trim
panels.Figure A)
2
TOYOTA FJ CRUISER 2007-2008
Using a panel removal tool, carefullyremove the side trim
panels.(Figure B)
3
Remove (2) Phillips screws from radiotrim panel. (Figure C)
4
Using panel removal tool, carefullyremove radio trim panel.
(Figure D)
5
Remove (4) 10mm bolts securing theradio.
6
7
DASH DISASSEMBLY
A
B
CD
Unplug and remove radio.
Continue to kit assembly.9
8 Remove factory brackets from radio.Retain brackets for use
during kitassembly.
-
11
Disconnect the negative battery terminal to prevent an
accidentalshort circuit.
1
Unclip the bottom trim panel locatedunderneath the A/C
Controls.Figure A)
2
YARIS 2007
Unclip the two side trim panels thatsurround the A/C Controls
and Radio.(Figure A)
3
Unclip the Instrument trim Panelsurrounding the Speedometer
andgauges. (Figure B)
4
Unclip the Radio/AC Vents trimPanel.(Figure B)
5
Remove (4) Phillips screws securingradio. (Figure C)
6
Continue to kit assembly.
7
A
B
C
Unplug and remove radio.
8 Remove (4) Phillips screws securingfactory brackets on each
side of theradio and remove brackets. Retainbrackets for use during
kit assembly.(Figure D)
D
9
DASH DISASSEMBLY
-
DASH DISASSEMBLY
SCION XA 2004-2006
12
Disconnect the negative battery terminalto prevent an accidental
short circuit.
Pull outward on the (3) climate controlknobs and remove. (Figure
A)
1
2
Remove (2) Phillips screws from behindthe outer two climate
knobs. (Figure B)
3
A
B
Unsnap and remove the trim pieces oneach side of the climate
control/ash-tray/pocket assembly. (Figure C)
4
Remove (2) phillips screws from thebottom of the climate
control/radio trimpanel and unsnap and remove the entirepanel.
(Figure D)
5
Remove (4) Phillips screws to removethe factory radio.
6
C
DContinue to kit assembly.8
7 Remove factory brackets from radio.Retain brackets for use
during kitassembly.
-
DASH DISASSEMBLY
SCION XB 2004-2007
13
Disconnect the negative battery terminalto prevent an accidental
short circuit.
Pull outward on the (3) climate controlknobs and remove. (Figure
A)
1
2
Remove (2) Phillips screws from behindthe outer (2) knobs.
(Figure B)
3
A
BUnsnap and remove the entire panelsurrounding the climate
controls andthe radio. (Figure C)
4
Remove (4) Phillips screws to removethe factory radio.
5
Continue to kit assembly.7
6 Remove factory brackets from radio.Retain brackets for use
during kitassembly.
-
DASH DISASSEMBLY
SCION XB 2008
14
Unclip and remove the trim panelaround the radio including the
a/c vents.(Figure A)
Unclip and remove the trim panel at thebottom edge of the dash
cavity. (Figure B)
1
2
Remove (4) 10 MM bolts securing theradio. (Figure C)
3
A
B
C
Continue to kit assembly.
-
DASH DISASSEMBLY
SCION TC 2005-2008
15
Disconnect the negative battery termi-nal to prevent an
accidental short cir-cuit.
Unsnap trim from around shifter (notnecessary to be removed).
(Figure A)
1
2
Unclip and remove panel from aroundradio. (Including climate
controls andradio door). (Figure B)
3
A
BRemove (2) 10mm nuts from the topmounting locations and (2)
10mm boltsfrom the bottom mounting locations toremove the radio.
(Figure C)
4
C
5 Remove factory brackets from radio.Retain brackets for use
during kitassembly.
Continue to kit assembly.6
-
DASH DISASSEMBLY
SCION XD 2008
16
Disconnect the negative battery termi-nal to prevent an
accidental short cir-cuit.
Unclip radio trim panel. Unplug andremove panel. (Figure A)
1
2
Remove (4) Phillips screws securingthe radio. Unplug and remove
radio.(Figure B)
3
A
B
Remove factory brackets from radio.Retain brackets for use
during kitassembly. (Figure C)
4
C
Continue to kit assembly.
-
17
Attach the factory mounting brackets
supplied with the unit. (Figure B)NOTE: Remove locating pins
from fac-tory brackets with grinder.
1
Attach the factory mounting brackets
the stacked ISO DIN head units withthe screws supplied with the
units.(Figure C) NOTE: Remove locating pinsfrom factory brackets
with grinder.
Continue to final assembly.
1
A
A
A
B
B
C
DOUBLE DIN HEAD UNIT PROVISION
STACKED ISO HEAD UNIT PROVISION
B
KIT ASSEMBLY
NOTE: For all Scion TC and XA you willneed to cut off the front
upper section ofthe DDIN trim plates, as shown by dottedlines
labeled “A” in (Figure A).For the 2001-2006 Toyota Rav 4,
the2001-2006 Toyota Highlander, and the2003-2006 Toyota
Sequoia/Tundra youwill need to cut off the rear section ofthe DDIN
trim plates, as shown by dottedlines labeled “B” in (Figure A).For
all other vehicles skip to Step 1.
and the DDIN trim plates tothe DDIN head unit with the
screws
and the DDIN trim plates to
-
18
FINAL ASSEMBLY1 Locate the factory wiring harness in the dash
and make the connection as shown.
as shown. (Isolate and individually tape off the ends of any
unused wires to pre-vent electrical short circuit.)
2 Re-connect the negative battery terminal and test the unit for
proper operation.3 Reassemble radio and dash assemblies in reverse
order of disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D
Make wiring connections using the EIA color code chart shown
below and the instructions included with the head
tape off ends of any unused wires to prevent electrical short
circuit.
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-) . . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle
chassis.All colors may not be present on all leads due to
manufacturer’s specifications.
FINAL WIRING CONNECTIONS
FINAL ASSEMBLY
Connects2 recommends using the proper mating adapter and making
the connections
WIRING CODE
unit. C onnects2 recommends making connections as shown below;
Strip, Splice, Solder, Tape. Isolate and individually
-
19
NOTES
-
20
NOTES
-
21
NOTES
-
INSTRUCTIONS