NEAX2000 IVS2 Data Interface System Manual

7/30/2019 NEAX2000 IVS2 Data Interface System Manual

1/100

ND-70924 (E)ISSUE 1

STOCK # 151993

Data Interface System Manual

JULY, 2000

NEC America, Inc.


2/100

LIABILITY DISCLAIMER

NEC America, Inc. reserves the right to change the specifications,functions, or features, at any time, without notice.

NEC America, Inc. has prepared this document for use by itsemployees and customers. The information contained herein is

the property of NEC America, Inc. and shall not be reproducedwithout prior written approval from NEC America, Inc.

NEAX and Dterm are registered trademarks of NEC Corporation.

Copyright 2000

NEC America, Inc.

Printed in U.S.A.


3/100

ISSUE 1 ISSUE 2 ISSUE 3 ISSUE 4

DATE JULY, 2000 DATE DATE DATE


DATE DATE DATE DATE

NEAX2000 IVS2

Data Interface System Manual Revision Sheet 1/2

ND-70924 (E)

PAGE No.ISSUE No.

1 2 3 4 5 6 7 8

i 1

ii 1

iii 1

iv 1

1 12 1

3 1

4 1

5 1

6 1

7 1

8 1

9 1

10 1

11 1

12 1

13 1

14 1

15 1

16 1

17 1

18 1

19 1

20 1

21 1

22 1

23 1

24 1

25 1

26 1

27 1

28 1

29 1

30 1

31 1

32 1

33 1

34 1

35 1

36 1

37 1

38 1

39 140 1

41 1

42 1

43 1

44 1

45 1

46 1

47 1

48 1

49 1

50 1

51 1

52 1

53 1

54 1

55 1

56 1

57 1

58 1

59 1

60 1

61 1

62 1

63 1

64 1

65 1

66 1

67 1

68 1

69 1

70 1

71 1

72 1

PAGE No.ISSUE No.

1 2 3 4 5 6 7 8


4/100


DATE JULY, 2000 DATE DATE DATE


DATE DATE DATE DATE

NEAX2000 IVS2

Data Interface System Manual Revision Sheet 2/2

ND-70924 (E)

73 1

74 1

75 1

76 1

77 178 1

79 1

80 1

81 1

82 1

83 1

84 1

85 1

86 1

87 1

88 1

89 1

90 1

91 1

92 1

93 1

94 1

PAGE No.ISSUE No.

1 2 3 4 5 6 7 8PAGE No.

ISSUE No.

1 2 3 4 5 6 7 8


5/100

NEAX2000 IVS2 Data Interface System ManualND-70924 (E), Issue 1.0 Page i

NEAX2000 IVS2

Data Interface System Manual

TABLE OF CONTENTSPage

LIST OF FIGURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

LIST OF TABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1PURPOSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

OUTLINE OF THIS MANUAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

REFERENCE MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

CHAPTER 1 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3SYSTEM OUTLINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

DPC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

DTI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7M03 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

PLO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

CARD NAME AND FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

SYSTEM CAPACITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

System Capacity for Data Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

System Capacity for Digital Trunk Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

SYSTEM SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

DPC Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Modem Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

SYSTEM CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Time Slot Assignment Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Time Slot Allocation for DTI Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

CHAPTER 2 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Static Electricity Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

REQUIRED EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

INSTALLATION PROCEDURE FOR DATA INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Installation Summary for Data Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Mounting DPC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Mounting M03 Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Conditions on Connecting DTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Connecting X.21 DTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Connecting V.24/V.28 DTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Connecting RS-449 DTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Connecting V.35 DTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Installation Procedure for Digital Trunk Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Installation Summary for Digital Trunk Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Mounting DTI Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39


6/100

NEAX2000 IVS2 Data Interface System ManualPage ii ND-70924 (E), Issue 1.0

TABLE OF CONTENTS

Page

Mounting CONN Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

DTI Cable Connection via MDF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

DTI Cable Connection via CONN Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

CHAPTER 3 SYSTEM DATA PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45HOW TO READ THIS CHAPTER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

DATA INTERFACE ASSIGNMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

DIGITAL TRUNK INTERFACE ASSIGNMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

CHAPTER 4 OPERATION TEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55DPC LOOPBACK TEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

DPC Loopback 1 Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

DPC Loopback 2 Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

OTHER LOOPBACK TESTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

INTER-OFFICE DIGITAL DATA TRANSMISSION TEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

CHAPTER 5 CIRCUIT CARD INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63HOW TO READ THIS CHAPTER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

MOUNTING LOCATION OF CIRCUIT CARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

LIST OF REQUIRED CIRCUIT CARDS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

PN-CP14 (MP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

PN-24DTA-C (DTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

PN-30DTC-A (DTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

PZ-M542 (CONN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

PZ-M557 (CONN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

PN-2DPCB (DPC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88PN-M03 (M03) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92


7/100

LIST OF FIGURES

Figure Title Page

NEAX2000 IVS2 Data Interface System ManualND-70924 (E), Issue 1.0 Page iii

Figure 1-1 System Outline of Intra-Office Data Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Figure 1-2 System Outline of Inter-Office Data Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Figure 1-3 Clock Supply Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Figure 1-4 Accommodation of DTI into TDSW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 1-5 Time Slot Allocation for DTI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Figure 2-1 Static Electricity Guard (1 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Figure 2-1 Static Electricity Guard (2 of 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Figure 2-2 Installation Procedure for Data Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Figure 2-3 Limitation on Using Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Figure 2-4 Cable Connection between DPC Card and X.21 DTE/Modem . . . . . . . . . . . . . . . . . . 23

Figure 2-5 Cable Connection between DPC Card and X.21 DTE/Modem . . . . . . . . . . . . . . . . . . 25

Figure 2-6 DPC V11 Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Figure 2-7 Cable Connection between DPC Card and V.24/V.28 DTE/Modem . . . . . . . . . . . . . . 28

Figure 2-8 Cable Connection between DPC Card and V.24/V.28 DTE/Modem . . . . . . . . . . . . . . 29

Figure 2-9 DPC RS Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Figure 2-10 Cable Connection between DPC Card and RS-449 DTE . . . . . . . . . . . . . . . . . . . . . . 31Figure 2-11 RS-449 Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Figure 2-12 X.21 Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Figure 2-13 Outline of V.35 Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Figure 2-14 Cable Connection between M03 Card and V.35 DTE/Modem . . . . . . . . . . . . . . . . . . 34

Figure 2-15 Cable Connection between M03 Card and V.35 DTE/Modem . . . . . . . . . . . . . . . . . . 35

Figure 2-16 DPC V35 Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Figure 2-17 V.35 Connector Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Figure 2-18 Installation Procedure for DTI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Figure 2-19 DTI Cable Connection via MDF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Figure 2-20 Location of the AP Slots and the LTC Connectors for DTI . . . . . . . . . . . . . . . . . . . . . 41

Figure 2-21 Example of MDF Cross Connection for DTI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Figure 2-22 DTI Cable Connection via CONN Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Figure 2-23 Example of Coaxial Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Figure 4-1 DPC Loopback Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Figure 4-2 Connection of Modem Tester . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Figure 4-3 Other Loopback Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Figure 4-4 Inter-Office Digital Data Transmission Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Figure 5-1 Mounting Location of Circuit Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65


8/100

NEAX2000 IVS2 Data Interface System ManualPage iv ND-70924 (E), Issue 1.0

LIST OF TABLES

Table Title Page

Table 1-1 Connecting Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Table 1-2 Card Name and Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Table 1-3 System Capacity for Data Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Table 1-4 System Capacity for Digital Trunk Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Table 1-5 DPC Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Table 1-6 Rate Adaptation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Table 1-7 Modem Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Table 2-1 Required Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Table 2-2 X.21 to RS-449 Adapter Cable Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Table 2-3 V.35 Interface Cable Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Table 5-1 List of Required Circuit Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66


9/100

INTRODUCTIONPurpose

NEAX2000 IVS2 Data Interface System ManualND-70924 (E), Issue 1.0 Page 1

INTRODUCTION

PURPOSE

This manual explains the installation, programming and operation test procedure for the Data

Interface system on the NEAX2000 IVS2.

OUTLINE OF THIS MANUAL

This manual contains the following chapters:

CHAPTER 1 GENERAL INFORMATION

This chapter explains the system outline, the name and functions of circuit cards required,system capacity, system specifications and system conditions of Data Interface system.

CHAPTER 2 INSTALLATION

This chapter explains the hardware installation procedure to provide Data Interface on the PBX.

CHAPTER 3 SYSTEM DATA PROGRAMMING

This chapter explains the programming procedure to provide the Data Interface on the PBX.

CHAPTER 4 OPERATION TEST

This chapter explains the operation tests to be performed after completing the installation of theData Interface on the PBX.

CHAPTER 5 CIRCUIT CARD INFORMATION

This chapter explains the mounting location, the meaning of lamp indications, and the method of

switch settings of each circuit card for the Data Interface.


10/100

NEAX2000 IVS2 Data Interface System ManualPage 2 ND-70924 (E), Issue 1.0

INTRODUCTIONReference Manual

REFERENCE MANUAL

During installation, refer also to the manuals below:

Command Manual: Describes Customer Administration Terminal (CAT)

operation, command function and setting data required for

programming the system, and Resident System Program.

Office Data Programming Manual: Contains the Customer Specification Sheet and Office Data

Programming Sheet.

Maintenance Manual: Describes the maintenance service features and the

recommended troubleshooting procedure.

Installation Procedure Manual: Explains the installation procedure for the PBX system.


11/100


CHAPTER 1

GENERAL INFORMATION

This chapter explains the Data Interface system outline, the name and

functions of circuit cards required, system capacity, specifications,

and conditions.


12/100


CHAPTER 1 GENERAL INFORMATIONSystem Outline

SYSTEM OUTLINE

The Data Interface can provide the intra- or inter-office digital data transmission on fixed path

(Nailed-Down) connection. The Data Interface equips the V.11 (X.21) and the V.24/V.28

(RS-232C) interface. When you use the V.11 (X.21) interface, a maximum of 64 kbps digital data

transmission is available. When you use the V.24/V.28 (RS-232C) interface, a maximum of 19.2

kbps digital data transmission is available.

To add the V.11 (X.21) or V.24/V.28 (RS-232C) Data Interface to the system, it is necessary to

install the Data Port Controller (DPC) card. You can provide the V.35 interface DTE by the M03

card installed in addition to the DPC card. The M03 card converts the V.11 (X.21) interface to a

V.35 interface. When you provide the inter-office digital data transmission, it is necessary to

install the 24/30-channel Digital Trunk Interface (DTI) card in addition to the DPC card.

Figure 1-1 and Figure 1-2 show the outline of the Data Interface intra-office/inter-officeconnection.

Figure 1-1 System Outline of Intra-Office Data Connection

NOTE: The DPC card can only operate as DCE. If the DPC card is to be connected to a modem

or other DCE, a null modem adapter is required.

SYNCHRONOUS

DATA AT SPEEDSOF 56 kbps, 64 kbps

PBX

DTE

DTE

DPC

DPC

NAILED-DOWN CONNECTION(DATA STATION TO DATA STATION)

DPC: DATA PORT CONTROLLER

DTE: DATA TERMINAL EQUIPMENT


13/100



When the PBX is an end office in the Inter-Office Digital Data Transmission through Nailed-Down

Connection, the digital signal is transmitted directly. A maximum of 64 kbps digital data

transmission is available for the direct digital transmission.

When the PBX is a tandem office in the Inter-Office Digital Data Transmission through Nailed-

Down Connection, data transparency is provided, and a maximum of 64 kbps digital data

transmission is available.

Table 1-1 shows the connecting pattern of the Inter-Office Data Transmission through Nailed-

Down Connection.

: Direct Connection: Tandem Connection

: Not available

Table 1-1 Connecting Patterns

CONNECTING PATTERNSYSTEM

CONFIGURATIONTOFROM

LDT/ODT DTI(DIGITAL SIGNAL)

DPC Figure 1-2

LDT/ODT

DTI

(Digital Signal)

Figure 1-2


14/100



Figure 1-2 System Outline of Inter-Office Data Connection

DTI

PBX

(2) PBX IS A NTANDEM OFFICE:

DTI

PBX

DTE

DPC

DPC

DPC: DATA PORT CONTROLLER

DTE : DATA TERMINAL EQUIPMENT

DTI : 24/30 CHANNEL DIGITAL TRUNK INTERFACE

M : MODEM

PLO : PHASE LOCKED OSCILLATOR

DTE

DPC

MMTODTE

DTI

MP PLO

NAILED-DOWN CONNECTION

24/30 CHANNEL PCMDIGITAL LINE

DIGITALPBX

CLOCK SIGNAL

TDSW

(1) PBX IS AN END OFFICE:

NAILED-DOWN CONNECTION

MP PLO

CLOCK SIGNALTDSW


15/100



DPC

The Data Port Controller (DPC) can accommodate a maximum of two DTE per cards with V.11

(X.21) or V.24/V.28 (RS-232C) interface, and can provide the intra-office or inter-office digital

data transmission on Nailed-Down connection.

DTI

The Digital Trunk Interface (DTI) interfaces the PBX directly to a 24/30-channel PCM

transmission line. The DTI has the following functions.

For 24DTI:

Unipolar/Bipolar Conversion (AMI Format)

Signaling Insertion/Extraction

Alarm Detection/Insertion

Digital PAD on Voice Signal Transmission

Loopback Test (Local/Remote Loopback)

Cyclic Redundancy Checking (based on ITU-T Rec. G704)

For 30DTI:

Unipolar/Bipolar Conversion (HDB3 Format)

Signaling Insertion/Extraction

Alarm Detection/Insertion

Digital PAD on Voice Signal Transmission

Cyclic Redundancy Checking (based on ITU-T Rec. G704)

Channel Associated Signaling (based on ITU-T Rec. 0421 Digital R2 Signaling Code)

For connection of a 24DTI and transmission line, twisted-pair cables can be used. For connection

of a 30DTI and transmission line, either coaxial cable or twisted pair cable can be used.

M03

The M03 provides V.35 Data Terminal Equipment interface.

M03 is connected to the DPC and converts V.11 (X.21) interface to V.35 interface.


16/100



PLO

The Phase Locked Oscillator (PLO) equipped on the MP card synchronizes the system to the

digital network clock.

When the PBX is a clock receiver office, the PLO generates the clock signals according to the

source clocks received from the source office within the network. The source clock signals are

extracted at DTI cards and supplied to the PLO. Two clock routes are available; one is the Route

0 from the source office, and the other is a standby Route 1 from a sub-source office. When no

clock signals arrive from the source and sub-source office, due to a transmission line failure, the

PLO keeps generating the clock signals at the frequency of the previous source clock. The PLO

can receive different frequency of source clocks from the Route 0 and Route 1.

Figure 1-3 shows an example of the clock supply route when the system is a receiver office.

Figure 1-3 Clock Supply Route

NOTE: DTI 0 and DTI 1 must be mounted in PIM0.

PLO

TDSW

SOURCE OFFICE

~

SOURCECLOCK

RECEIVER/LOCAL-RECEIVER OFFICE

DTI

DTI

TDSW

RECEIVER OFFICE

DTI

DTI

DTI

TDSW

SUB-SOURCE OFFICE

PLO

DTI

DTI 1

DTI 0DTI

DTI

PLO

PLO: DIRECTION OF CLOCK

SIGNAL SUPPLY

TDSW

PBX NOTE


17/100

CHAPTER 1 GENERAL INFORMATIONCard Name and Function


CARD NAME AND FUNCTION

Table 1-2 shows the circuit card name and function for Data Interface.

Table 1-2 Card Name and Function

EQUIPMENT

NAME

FUNCTIONAL

NAMEFUNCTION

PN-CP14 MP Main Processor Card

Provides Memory, TDSW (1024CH 1024CH), 16-line

CFT, PB sender, Clock, PLO 2 ports (receiver mode/

source mode), two RS-232C ports, 2-line DAT (Recording

duration: Max. 128 sec.), DK, 4-line PB receiver, Modem

for remote maintenance (19.2 kbps), internal Music-on-

Hold tone source and BUS interface. BUS interfacefunctions as a driver/receiver of various signals, adjusts

gate delay timing and cable delay timing, monitors I/O Bus

and PCM BUS.

One card is required per system.

PN-24DTA-C DTI Digital Trunk Interface (23B + D, 1.5 Mbps) Card

Accommodates 24-channel PCM digital lines.

PN-30DTC-A DTI Digital Trunk Interface (2 Mbps) Card

Accommodates 30-channel PCM digital lines.

PZ-M542

[For Other

Countries]

CONN Coaxial Cable Connection Card

Used to connect a coaxial cable for the Digital Trunk

Interface.

Two cards maximum can be connected to LTC connector

of each PIM.

PZ-M557

[For

Australia]

CONN Coaxial Cable Connection Card

Used to connect a coaxial cable for the Digital Trunk

Interface.

Two cards maximum can be connected to LTC connectorof each PIM.


18/100


CHAPTER 1 GENERAL INFORMATIONCard Name and Function

PN-2DPCB DPC 2-line Data Port Controller Card

Used for the intra-office or inter-office digital data

transmission on nailed down connection.

Accommodates max. two DTEs with V.11 (X.21) interface

or V.24/V.28 (RS-232C) interface.

PN-M03 M03 V.35 Data Terminal Equipment Interface Card

Used together with the PN-2DPCB card to provide the

V.35 interface.

Table 1-2 Card Name and Function (Continued)

EQUIPMENT

NAME

FUNCTIONAL

NAMEFUNCTION


19/100

CHAPTER 1 GENERAL INFORMATIONSystem Capacity


SYSTEM CAPACITY

System Capacity for Data Interface

System Capacity for Digital Trunk Interface

Table 1-3 System Capacity for Data Interface

DESCRIPTION CAPACITY REMARKS

DPC Card 50

Circuits per DPC Card 2

Fixed Path Connection 100

Table 1-4 System Capacity for Digital Trunk Interface

DESCRIPTIONCAPACITY

REMARKS24DTI 30DTI

DTI Card 8 4

DTI Trunk 192 124

DTI Trunk Route 64 64 1 Route/DTI

Ports per DTI Card 24 31


20/100


CHAPTER 1 GENERAL INFORMATIONSystem Specifications

SYSTEM SPECIFICATIONS

DPC Specifications

NOTE 1: When the transmission rate is 56 or 64 kbps, only full duplex is available.

NOTE 2: For the transmission rate after Rate Adaptation, see Table 1-6.

Modem Specifications

NOTE: When the transmission rate is 56 or 64 kbps, only full duplex is available.

Table 1-5 DPC Specifications

DESCRIPTION SPECIFICATION

Synchronization Synchronous

Transmission Rate 2.4, 4.8, 9.6, 14.4, 19.2, 48, 56, 64 kbps

Transmission Mode Full/Half Duplex NOTE 1

Rate Adaptation NOTE 2 ITU-T V.110

Table 1-6 Rate Adaptation

TRANSMISSION RATE

BEFORE RATE ADAPTATION

TRANSMISSION RATE

AFTER RATE ADAPTATIONREMARKS

2.4-4.8 kbps 8 kbps

9.6 kbps 16 kbps

14.4 kbps 32 kbps

19.2 kbps 32 kbps

48-64 kbps 64 kbps

Table 1-7 Modem Specifications

DESCRIPTION SPECIFICATION

Synchronization Synchronous

Transmission Rate 2.4, 4.8, 9.6, 14.4, 19.2, 48, 56, 64 kbps

Transmission Mode Full/Half Duplex NOTE

Line 4 wire

Connecting Type Leased


21/100

CHAPTER 1 GENERAL INFORMATIONSystem Conditions


SYSTEM CONDITIONS

Time Slot Assignment Condition

As shown in Figure 1-4, the 30DTI card uses the time slot on the basic Highway 4.

Therefore, the total number of time slots for all 30DTI card must be 128 time slots or lessincluding all other application processor cards which use the Highway 4.

The 24DTI card can use the time slot on both the basic and expanded Highway 4 and 6.

Therefore, the total number of time slots for all 24DTI card must be 256 time slots or less.

Figure 1-4 Accommodation of DTI into TDSW

PRT

TDSW(1024T

IMESLOTS)

FP0

FP1

FP2

FP3

DTI

DCH

FOR L/T CARDS: MAX. 512 TIME SLOTS PER SYSTEM

FOR BASIC HIGHWAY4: MAX. 128 TIME SLOTS PER SYSTEM

1 TIME SLOT/CARD

MAX. 128 TIME SLOTS

MAX. 128 TIME SLOTS

MAX. 128 TIME SLOTS

MAX. 128 TIME SLOTS

30DTI: MAX. 31 TIME SLOTS/CARD

BRT

ICH

DTI

MAX. 2 TIME SLOTS/CARD (BRTA)

MAX. 4 TIME SLOTS/CARD (2BRTC)

25 TIME SLOT/CARD

24DTI: MAX. 24 TIME SLOTS/CARD

1 TIME SLOT/CARD (SC02)

4 TIME SLOTS/CARD (SC03)

FOR EXPANDED HIGHWAY6: MAX. 128 TIME SLOTS PER SYSTEM

HW4

HW6

FOR AP CARDS: MAX. 256 TIME SLOTS PER SYSTEM


22/100


CHAPTER 1 GENERAL INFORMATIONSystem Conditions

Time Slot Allocation for DTI Card

On each DTI card, the system recognizes the lowest and highest channel numbers to which trunk

numbers have been assigned, and allocates time slots to all the channels within them. If trunk

numbers are assigned to discontinuous channels in this case, the system also allocates time

slots to channels not assigned.

For example, as shown in Figure 1-5, even when Channel 1 through Channel 10 have been

assigned by the system data programming (CM07 YY=01) except Channel 5, the system

allocates a total of 10 time slots for all the ten channels. Therefore, to avoid allocation of

unnecessary time slots, it is recommended that consecutive channels are assigned on each DTI

card.

Figure 1-5 Time Slot Allocation for DTI

10

9

6

5

4

1

CH0

DXXX

DXXX

DXXX

NONE

DXXX

DXXX

NONE

LOWEST CHANNEL

HIGHEST CHANNEL

10 TIME SLOTS AREALLOCATED EVENWHEN CH5 IS NOT

ASSIGNED.


23/100


CHAPTER 2

INSTALLATION

This chapter explains the hardware installation procedure to provide

Data Interface to the PBX.


24/100


CHAPTER 2 INSTALLATIONPrecautions

PRECAUTIONS

Static Electricity Guard

You must wear a grounded wrist strap to protect circuit cards from static electricity.

Figure 2-1 Static Electricity Guard (1 of 2)

WHEN PLUGGING/UNPLUGGING A CIRCUIT CARD

WHEN HOLDING A CIRCUIT CARD

PBX

WRIST STRAP

FRAME GROUND SCREW

CARD FRONT

NEVER TOUCH THE COMPONENTS OR

SOLDERED SURFACE WITH BARE HANDS.


25/100


26/100


CHAPTER 2 INSTALLATIONPrecautions

CautionYou must hold the edge of a circuit card when plugging or unplugging the circuit card. If you

touch another area, you may be exposed to hazardous voltages.

CARD FRONT

NEVER TOUCH THE COMPONENTS OR

SOLDERED SURFACE WITH BARE

HANDS.

PBX


27/100

CHAPTER 2 INSTALLATIONRequired Equipment


REQUIRED EQUIPMENT

Table 2-1 shows the equipment required to provide the Data Interface on the system.

Table 2-1 Required Equipment

EQUIPMENT/CABLE DESCRIPTION QTY REMARKS

PN-2DPCB Data Port Controller Card 1-50

PN-24DTA-C 24 channel DTI Card 1-8 For Inter-office

PN-30DTC-A 30 channel DTI Card 1-4 For Inter-office

PN-M03 V.35 DTE Interface Card 1-50

PZ-M542/M557 Coaxial Cable Connection

Card

1-4 2 cards/PIM

1 card/DTI

DPC V11 CABLE Connection Cable between

PN-2DPCB and V.11

(X.21) DTE

N N: Number of V.11

(X.21) DTE

4 m (13.1 ft.)

17-TW-0.3 CONN

CABLE-A

Connection Cable between

PN-2DPCB and PN-M03

N N: Number of V.35 DTE

0.3 m (1 ft.)

DPC V35 CABLE Connection Cable between

PN-M03 and V.35 DTE

N N: Number of V.35 DTE

4 m (13.1 ft.)

DPC RS CABLE Connection Cable betweenPN-2DPCB and V.24/V.28

DTE

N N: Number of V.24/V.28DTE

4 m (13.1 ft.)

MODEM Refer to Modem

Specifications. Page 12

2 N N: Number of DTE

(As required)

(Should be provided by

customer.)

Straight Cable Connection Cable between

DPC V11 CABLE/DPC RS

CABLE and DTE

N N: Number of DTE

(When connecting DTE

directly)(Should be provided by

customer.)

Reverse Cable Connection Cable between

DPC V11 CABLE/DPC RS

CABLE and Modem

N N: Number of DTE

(When using modem)

(Should be provided by

customer.)


28/100


CHAPTER 2 INSTALLATIONInstallation Procedure for Data Interface

INSTALLATION PROCEDURE FOR DATA INTERFACE

Installation Summary for Data Interface

Install the equipment according to the procedure shown in Figure 2-2.

Figure 2-2 Installation Procedure for Data Interface

START

Mounting DPC Card

END

Page 21

Mounting M03 CardConnecting X.21 DTE Connecting RS-449

Whichtype of DTE?

DTEConnecting V.24/V.28

DTE

Connecting V.35 DTE

Page 21Page 31Page 28Page 23

Page 33

X.21 V.24/V.28 RS-449 V.35


29/100



Mounting DPC Card

(1) Confirm the correct switch settings of the DPC card.

See CHAPTER 5. Page 63.

(2) Mount the DPC cards in LT00 through LT11 slots of PIM0 through PIM7.

Mounting M03 Card

(1) Confirm the correct switch settings of the M03 card.

See CHAPTER 5. Page 63.

(2) Mount the M03 cards in LT00 through LT11 slots of PIM0 through PIM7.

ATTENTIONContentsStatic SensitiveHandling

Precautions Required


30/100



Conditions on Connecting DTE

Forcible ON control of DTR, RTS/C signal:

When connecting the DTE which does not support the DTR signal and RTS/C signal, these

signals can be turned to ON forcibly by switch setting on the DPC card.

Condition of CTS signal ON control:

The CTS signal is turned to ON after 60 ms from the time when receiving the RTS/C signal. And

the CTS signal is turned to ON under the following conditions.

1. The DTR signal is ON.

2. The received X signal is ON (The synchronization of the opposite office is established).

3. The sending X signal is ON (The synchronization of the PBX is established).

Limitation on using modem:When using modem, the DTR signal from the DTE can not be transmitted to the PBX (DPC card).

Therefore, the DTE starting by the DTR signal can not be used.

Figure 2-3 Limitation on Using Modem

TXD

RXD

DTR

RTSCTS

DCD

DSR

TXC(2)

RXC

TXD

RXD

DTR

RTSCTS

DCD

DSR

TXC(2)

RXC

TXC(1)

TXD

RXD

DTR

RTSCTS

DCD

DSR

TXC(2)

RXC

TXC(1)

TXD

RXD

DTR

RTSCTS

DCD

DSR

TXC(2)

RXC

TXD

RXD

DTR

RTSCTS

DCD

DSR (ON)

TXC(2)

RXC

TXC(1)

S-BB TXD

RXD

DTR

RTSCTS

DCD

DSR

TXC(2)

RXC

TXC(1)

~

X DTR

DTE PBX PBX MODEM MODEM DTE


31/100



Connecting X.21 DTE

Connect the X.21 DTE/modem to the DPC card as shown in Figure 2-4.

Figure 2-4 Cable Connection between DPC Card and X.21 DTE/Modem

(Continued)

2A

2B

3A

3B

4A

4B

5A

5B

6A

4D

3C

6D

6B

2

9

3

10

4

11

5

12

6

8

13

2

9

3

10

4

11

5

12

6

14

7

8

13

T

C

R

I

S

TXC(1)

GND

T

C

R

I

S

GND

T

C

R

I

S

TXC(1)

GND

XCN0/XCN1 CONNECTOR

STRAIGHT CABLE (LOCALLY PROVIDED)

DPC

X.21DTE

(J) (J) (P) (P)

4 m (13.1 ft.)

14

7TXC(1)

DPC V11 CABLE

Page 27

(1) Direct Connection

NOTE 1

L NOTE 2


32/100



NOTE 1: When providing X.21 DTE with TXC(1) signal, this connection is required.

NOTE 2: The distance between the DPC card and X.21 DTE is as follows.

When providing X.21 DTE with TXC(1) signal: L=Max. 1000 m (3281 ft.)When providing X.21 DTE without TXC(1) signal, the distance depends on the data

speed.

(Continued)

Distance (L) Data SpeedMax. 1000 m (3281 ft.) . . . . . . .

Max. 800 m (2625 ft.) . . . . . . . .

Max. 350 m (1148 ft.) . . . . . . . .

Max. 300 m (984 ft.) . . . . . . . . .

Max. 250 m (820 ft.) . . . . . . . . .

Less than 9.6 kbps

19.2 kbps

48 kbps

56 kbps

64 kbps


33/100



Figure 2-5 Cable Connection between DPC Card and X.21 DTE/Modem

(Continued)

XCN0/XCN1 CONNECTOR

REVERSE CABLE (LOCALLY PROVIDED)

DPC

X.21MODEM

(J) (J) (P) (P)

4 m (13.1 ft.)

2A

2B

3A

3B

4A

4B

5A

5B

6A

4D

3C

6D

6B

2

9

3

10

4

11

5

12

6

8

13

2

9

3

10

4

11

5

12

6

14

7

8

13

T

C

R

I

S

TXC(1)

GND

T

C

R

I

S

GND

T

C

R

I

S

TXC(1)

GND

When using a modem that has not TXC(1) terminal

When using a modem that can provide TXC(1) signal

14

7TXC(1)

DPC V11 CABLE

Page 27

(2) Modem Connection

2A

2B

3A

3B

4A4B

5A

5B

6A

4D

3C

6D

6B

2

9

3

10

411

5

12

6

14

7

8

13

T

C

R

I

S

TXC(1)

GND

T

C

R

I

S

GND

T

C

R

I

S

TXC(1)

GND

TXC(1)

2

9

3

10

411

5

12

6

14

7

8

13

TXD

RTS

RXD

DCD

TXC(2)

NOTE 1

L NOTE 2


34/100



NOTE 1: When providing X.21 modem with TXC(1) signal, this connection is required.

NOTE 2: The distance between the DPC card and X.21 modem is as follows.

When providing X.21 modem with TXC(1) signal: L=Max. 1000 m (3281 ft.)When providing X.21 modem without TXC(1) signal, the distance depends on the data

speed.

Distance (L) Data SpeedMax. 1000 m (3281 ft.) . . . . . . .

Max. 800 m (2625 ft.) . . . . . . . .

Max. 350 m (1148 ft.) . . . . . . . .

Max. 300 m (984 ft.) . . . . . . . . .

Max. 250 m (820 ft.) . . . . . . . . .

Less than 9.6 kbps

19.2 kbps

48 kbps

56 kbps

64 kbps


35/100



Figure 2-6 DPC V11 Cable

.............

............

D A (J)

(J)

1

6

1 9

158

6D-GND

2A-TA

2B-TB

4A-RA

4B-RB

6A-SA

6B-SB

3C-TXC(1)A

4D-TXC(1)B

3A-CA

3B-CB

5A-IA

5B-IB

IA-G

8-GND

2-TA

9-TB

4-RA

11-RB

6-SA

13-SB

7-TXC(1)A

14-TXC(1)B

3-CA

10-CB

5-IA

12-IB

6

5

4

3

2

1

SA

IA

RA

CA

TA

G

A

SB

IB

RB

CB

TB

B

X

TXC(1)

X

C

GND

TXC(1)

X

D

7

6

5

4

3

2

8

1

TXC(1)A

SA

IA

RA

CA

TA

GND

X

14

13

12

11

10

9

15

TXC(1)B

SB

IB

RB

CB

TB

X

X: NOT CONNECTEDG: GROUND


36/100



Connecting V.24/V.28 DTE

Connect the V.24/V.28 DTE/modem to the DPC card as shown in Figure 2-7.

Figure 2-7 Cable Connection between DPC Card and V.24/V.28 DTE/Modem

(Continued)

05B

05A

04B

04A

03B

03A

02B

02A

06A

04D

05C

06B

GND

RXD

CTS

GND

TXC(2)

DTR

RS0/RS1 CONNECTOR


DPC

V.24/V.28DTE

(J) (J) (P) (P)

4 m (13.1 ft.)

MAX 15 m (49.2 ft.)

DPC RS CABLE

Page 30

TXD

RTS

DSR

DCD

RXC

TXC(1)

1

2

3

4

5

6

7

8

15

24

20

17

GND

RXD

CTS

GND

TXC(2)

DTR

TXD

RTS

DSR

DCD

RXC

TXC(1)

1

2

3

4

5

6

7

8

15

24

20

17

GND

RXD

CTS

GND

TXC(2)

DTR

TXD

RTS

DSR

DCD

RXC

TXC(1)



37/100



Figure 2-8 Cable Connection between DPC Card and V.24/V.28 DTE/Modem

RS0/RS1 CONNECTOR


DPC

V.24/V.28MODEM

(J) (J) (P) (P)

4 m (13.1 ft.)

MAX 15 m (49.2 ft.)

DPC RS CABLE

page 30

05B

05A

04B

04A

03B

03A

02B

02A

06A

04D

05C

06B

GND

RXD

CTS

GND

TXC(2)

DTR

TXD

RTS

DSR

DCD

RXC

TXC(1)

1

2

3

4

5

6

7

8

15

24

20

17

GND

RXD

CTS

GND

TXC(2)

DTR

TXD

RTS

DSR

DCD

RXC

TXC(1)

1

2

3

4

5

6

7

8

15

24

20

17

GND

RXD

CTS

GND

TXC(2)

DTR

TXD

RTS

DSR

DCD

RXC

TXC(1)



38/100



Figure 2-9 DPC RS Cable

.............

............

D A

(J)

1

6

1 14

2513

05B-GND

02B-GND

05A-TXD

04B-RXD

04A-RTS

03B-CTS

03A-DSR

02A-DCD

05C-DTR

04D-TXC(1)

06A-TXC(2)

06B-RXC

01C-RI

01A-GND

1-GND

7-GND

2-TXD

3-RXD

4-RTS

5-CTS

6-DSR

8-DCD

20-DTR

24-TXC(1)

15-TXC(2)

17-RXC

22-RI

06

05

04

03

02

01

TXC(2)

TXD

RTS

DSR

DCD

G

A

RXC

GND

RXD

CTS

GND

B

DTR

X

RI

C

X

TXC(1)

X

D

12

11

10

9

8

7

13

6

X

X

X

X

DCD

GND

X

DSR

24

23

22

21

20

19

25TXC(1)

X

RI

X

DTR

X

X


5

4

3

2

1

CTS

RTS

RXD

TXD

GND

17

16

15

14

RXC

X

TXC(2)

X

18 X


39/100



Connecting RS-449 DTE

RS-449 DTE requires a locally provided conversion cable, as shown in Figure 2-10. This cable

must be equipped with a 15-pin male D-type connector and a 37-pin D-type connector (male or

female as required by DTE.) A modification is required to be installed in the 37-pin connector, as

shown in the Table 2-2, Figure 2-11 and Figure 2-12.

Figure 2-10 Cable Connection between DPC Card and RS-449 DTE

Table 2-2 X.21 to RS-449 Adapter Cable Connections

DPC (DCE)

X.21, 15-pin Male D-type

DTE

RS-449, 37-pin D-type

Name Function Pin Pin Name Source

TA Transmit data A 2 4 TXD + DTE

TB Transmit data B 9 22 TXD DTE

RA Receive data A 4 6 RXD + DCE

RB Receive data B 11 24 RXD DCE

SA Clock A 6 5

8

SCT +

SCR +

DCE

DCE

SB Clock B 13 23

26

SCT

SCR

DCE

DCE

CA Control A 3 7 RTS + DTE

CB Control B 10 25 RTS DTE

IA Indicate A 13

5 11

9

DCD +

DSR +

CTS +

DCE

DCE

DCEIB Indicate B 31

12 29

27

DCD

DSR

CTS

DCE

DCE

DCE

SG Signal ground

(zero volts)

19

8 20

37

Signal ground

RCV common

SND common

Common

Common

Common

XCN0/XCN1 CONNECTOR X.21 to RS-449 ADAPTER CABLE

DPC

RS-449DTE

(J) (J) (P) (J/P)

DPC V11 CABLE

Page 27

(LOCALLY PROVIDED)


40/100


41/100



Connecting V.35 DTE

(1) Connect the M03 card and the DPC card as shown in Figure 2-13.

(2) Connect the V.35 DTE/modem to the M03 card in the following pages.

Figure 2-13 Outline of V.35 Cable Connection

DPC

V.35DTE/

17-TW-0.3 CONN CABLE

DPC V35 CABLEM03

PBX

V.35 INTERFACE CABLE

MODEM

XCN0/XCN1 CONNECTOR

X21 CONNECTOR

V35 CONNECTOR

(LOCALLY PROVICED)


42/100



Figure 2-14 Cable Connection between M03 Card and V.35 DTE/Modem

NOTE: When you provide V.35 DTE using TXC(1) signal, this connection is required.

(Continued)

V35 CONNECTOR


M03

V.35DTE

(J) (J) (P) (P)

4 m (13.1 ft.)

MAX 15 m (49.2 ft.)

TXD 4A

4B

RXD 2A

2B

RTS 6A

CTS 6B

DSR 5A

GND 6D

DCD 5B

TXC(2) 3A

3B

RXC 1C

2D

DTR 5C

TXC(1) 3C

4D

TXD P

S

RXD R

T

RTS C

CTS D

DSR E

GND B

GND A

DCD F

TXC(2) Y

AA

RXC V

X

DTR H

TXC(1) U

W

TXD P

S

RXD R

T

RTS C

CTS D

DSR E

GND B

GND A

DCD F

TXC(2) Y

AA

RXC V

X

DTR H

TXC(1) U

WNOTE

DPC V35 CABLEPage 36



43/100



Figure 2-15 Cable Connection between M03 Card and V.35 DTE/Modem

V35 CONNECTOR


M03

V.35MODEM

(J) (J) (P) (P)

4 m (13.1 ft.)

MAX 15 m (49.2 ft.)

TXD 4A

4B

RXD 2A

2B

RTS 6A

CTS 6B

DSR 5A

GND 6D

DCD 5B

TXC(2) 3A

3B

RXC 1C

2D

DTR 5C

TXC(1) 3C

4D

TXD P

S

RXD R

T

RTS C

CTS D

DSR E

GND B

GND A

DCD F

TXC(2) Y

AA

RXC V

X

DTR H

TXC(1) U

W

TXD P

S

RXD R

T

RTS C

CTS D

DSR E

GND B

GND A

DCD F

TXC(2) Y

AA

RXC V

X

DTR H

TXC(1) U

W


DPC V35 CABLEPage 36


44/100



Figure 2-16 DPC V35 Cable

D A (J)

(J)

1

6

B

NN

6D-GND

2A-RXDA

2B-RXDB

4A-TXDA

4B-TXDB

6A-RTS

6B-CTS

3C-TXC(1)A

4D-TXC(1)B

3A-TXC(2)A

3B-TXC(2)B

5A-DSR

5B-DCD

1C-RXCA

6

5

4

3

2

1

RTS

DSR

TXDA

TXC(2)A

RXDA

G

A

CTS

DCD

TXDB

TXC(2)B

RXDB

B

DTR

TXC(1)A

RXCA

C

GND

TXC(1)B

RXCB

D


2D-RXCB

5C-DTR

1A-GND

B-GND

R-RXDA

T-RXDB

P-TXDA

S-TXDB

C-RTS

D-CTS

U-TXC(1)A

W-TXC(1)B

Y-TXC(2)A

AA-TXC(2)B

E-DSR

F-DCD

Y-RXCA

X-RXCB

H-DTR

A-GND

B GND

F DCD

L X

R RXDA

V RXCA

Z X

DD X

JJ X

NN X

D CTS

J X

N X

T RXDB

X RXCB

BB X

FF X

LL X

A GND

E DSR

K X

P TXDA

U TXC(1)A

Y TXC(2)A

CC X

HH X

MM X

C RTS

H DTR

M X

S TXDB

W TXC(1)B

AA TXC(2)B

EE X

KK X


45/100



Figure 2-17 V.35 Connector Pin Assignment

Table 2-3 V.35 Interface Cable Connector Pin Assignments

Pin Name Function Specification Source

A

B

C

D

E

F

H

GND

GND

RTS

CTS

DSR

RLSD

DTR

Frame Ground

Signal Ground

Request To Send

Clear To Send

Data Set Ready

Received Line Signal Detector

Data Terminal Ready

RS-232

RS-232

RS-232

RS-232

RS-232

DTE

DCE

DCE

DCE

DTE

P

S

TXD Send Data V.35 DTE

RT

RXD Receive Data V.35 DCE

U

W

SCTE Serial Clock Transmit External (A)

Serial Clock Transmit External (B)

V.35 DTE

V

X

SCR Serial Clock Receive (A)

Serial Clock Receive (B)

V.35 DCE

Y

AA (or aa)

SCT Serial Clock Transmit (A)

Serial Clock Transmit (B)

V.35 DCE

L, M, N, Z, BB, CC, DD, EE,HH, JJ, KK, LL, MM, NN Reserved for future V.35 use

B

F

R

V

D

T

X

Signal Pin

Chassis Ground A

Request To Send C

Data Set Ready E

Data Terminal Ready HTransmitted Data P

Transmitted Data S

Transmit Timing U

Transmit Timing W

Transmit Timing Y

Transmit Timing AA

Pin Signal

B Signal Ground

D Clear To Send

F Receive Line SignalDetect

R Received Data

T Received Data

V Receive Timing

X Receive Timing

A

E

P

U

Y

C

H

S

W

AA


46/100



INSTALLATION PROCEDURE FOR DIGITAL TRUNK

INTERFACE

Installation Summary for Digital Trunk Interface

Install the equipment according to the procedure shown in Figure 2-18.

Figure 2-18 Installation Procedure for DTI

NOTE: This procedure is required when you provide CONN card to connect a coaxial cable for

30DTI.

START

Selection of PLO inMP Card

Mounting DTI Card

DTI Cable Connection

Page 39

CHAPTER 5 Page 63

Page 40via MDF

Mounting CONN Card Page 39

NOTE

END

DTI Cable Connection Page 43

NOTEvia CONN Card


47/100



Mounting DTI Card

(1) Before mounting the DTI (PN-24DTA-C/PN-30DTC-A) card, set the MB

switch to UP position, and set the other switches to appropriate position.

See CHAPTER 5. Page 63

(2) Mount the DTI card in the following AP slots on PIM0-PIM7.

PIM0: AP00-AP10 slots

PIM1-7: AP00-AP11 slots

After mounting the card, set the MB to DOWN position to put the card in service.

NOTE: The DTI card (DTI 0, DTI 1) which sends a clock signal to PLO of the MP card must be

mounted in the AP slots on PIM0.

Mounting CONN Card

When you provide CONN (PZ-M542/M557) card to connect a coaxial cable for 30DTI, do the

following installation.

(1) Confirm the correct switch settings of the CONN card.

See CHAPTER 5. Page 63

(2) Mount the CONN card on LTC connector on BWB in the PIM which accomodates the DTIcards.

For details, refer to the Installation Procedure Manual.

ATTENTIONContentsStatic SensitiveHandling

Precautions Required


48/100



DTI Cable Connection via MDF

When you use a twisted-pair cable, connect the cable to a CSU via the MDF as shown below.

Location of AP Slots and LTC Connectors for DTI - Page 41

Example of MDF Cross Connection for DTI - Page 42

Figure 2-19 DTI Cable Connection via MDF

CSUMDF

LTC0/LTC1/LTC2/LTC3 CONNECTOR

TWISTED-PAIRCABLE

BWB

PBX(PIM0-PIM7)

MAX. 200 m (655 ft.)

Figure 2-20, Figure 2-21,Figure 2-22, Figure 2-23

(SHIELD TYPE)

DTI


49/100



Figure 2-20 Location of the AP Slots and the LTC Connectors for DTI

LTC0

01

02

03

04

05

06

07

08

09

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

RA

TA

RA

TA

RA

TA

MJ

RB

TB

RB

TB

RB

TB

MN

RA

TA

RA

TA

RA

TA

RB

TB

RB

TB

RB

TB

RA

TA

RA

TA

RA

TA

RB

TB

RB

TB

RB

TB

RA

TA

RA

TA

RA

TA

RB

TB

RB

TB

RB

TB

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

AP00SLOT

AP01

SLOT

AP02

SLOT

LTC1

01

02

03

04

05

06

07

08

09

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

AP03

SLOT

AP04SLOT

AP05

SLOT

LTC2

01

02

03

04

05

06

07

08

09

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

AP08

SLOT

AP07

SLOT

AP06SLOT

AP11

SLOT

AP10

SLOT

AP09

SLOT

LTC3

01

02

03

04

05

06

07

08

09

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

L

T

1

1

/A

P

1

1

L

T

1

0

/A

P

1

0

L

T

0

9

/A

P

0

9

L

T

0

8

/A

P

0

8

L

T

0

7

/A

P

0

7

L

T

0

6

/A

P

0

6

L

T

0

5

/A

P

0

5

L

T

0

4

/A

P

0

4

L

T

0

3

/A

P

0

3

L

T

0

2

/A

P

0

2

L

T

0

1

/A

P

0

1

L

T

0

0

/A

P

0

0


50/100



Figure 2-21 Example of MDF Cross Connection for DTI

17

18

19

20

RA

TA

42

43

44

45

RB

TB

LTC1 (J)

42

43

44

45

RB

TB

17

18

19

20

RA

TA

LTC1 (P)

PIM 0

J P MDFDTI

AP05RA

RB

TA

TB

17

42

18

43

17

42

18

43

RA

RB

TA

TB

TO CSU

LTC1

RECEIVE

TRANSMIT


51/100



DTI Cable Connection via CONN Card

When you use an coaxial cable, connect the cable to a CSU via the CONN (PZ-M542/M557) card

as shown in Figure 2-22.

Figure 2-23 shows an example of the cable connection when the 30DTI card is mounted in the

AP05 slot of PIM0.

Figure 2-22 DTI Cable Connection via CONN Card

CSU

LTC0/LTC1/LTC2/LTC3

COAXIAL CABLE

30DTI

BWBPBX

MAX. 6 dB loss at 1024 kHz

CONN

CONNECTOR


52/100



Figure 2-23 Example of Coaxial Cable Connection

2 COAXIAL CONNECTOR

1 LTC1 CONNECTOR

LTC1 (J) LTC1 (P)

PIM0

J PCONN

30DTI

AP05RA

RB

TA

TB

17

42

18

43

17

42

18

43

TO CSU

LTC1

RECIEVE

RCV

TRANSMIT

TRS

17

18

19

20

RA

TA

42

43

44

45

RB

TB

17

18

19

20

RB

TB

42

43

44

45

RA

TA

21


53/100


CHAPTER 3

SYSTEM DATAPROGRAMMING

This chapter explains the programming procedure to provide the Data

Interface to the PBX.


54/100


CHAPTER 3 SYSTEM DATA PROGRAMMINGHow to Read This Chapter

HOW TO READ THIS CHAPTER

In the programming procedure, the meaning of (1), (2) and markings are as follows.

(1) : 1st Data

(2) : 2nd Data

: Initial Data; With the system data clear command (CM00, CM01), the data with this

marking is automatically set for each command.

: A reset of the MP card is required after data setting.

Press SW1 switch on the MP card.

:A reset of the DTI card is required after data setting.

Set the Make Busy switch to UP and then DOWN.

INITIAL

DTI INITIAL


55/100

CHAPTER 3 SYSTEM DATA PROGRAMMINGData Interface Assignment


DATA INTERFACE ASSIGNMENT

DESCRIPTION DATA

To assign data station number by CM1A,

assign a station number (dummy number)to each port (LEN) on the DPC card.

NOTE 1: The station number must beassigned to the first LEN (level

0) and the third LEN (level 2) of

each LT slot (The station

number must be also assigned

to the unused port on the DPC

card).

NOTE 2: The * and # can not be usedas a station number.

(1)

(2)

000-763: LEN

FX-FXXXXXXXX: Station No.X: 0-9

Assign a data station number to the

station number assigned by CM10.

NOTE: The data station number must bealso assigned to the unused port

on the DPC card.

(1)

(2)

X-XXXXXXXX: Station No. assigned

by CM10

X-XXXXXXXX: Data Station No.

Assign an access code for data station. (1)(2)

Y=0-3 Numbering Plan Group 0-3

X-XXXX: Access Code

801: 1 digit station

802: 2 digits station







Assign the type of data terminal interface

to the data station number.

NOTE: This data must be also assignedto the unused port on the DPC

card.

(1)

(2)


04: DPC

CM1A

CM20

START

CM10

CMA0

A

INITIAL

INITIAL


56/100



DESCRIPTION DATA

Assign the attribute data for data station

(assigned by CM1A) in accordance withthe specification of the DTE connected.

(1)

(2)

YY=04 Data speed

X-XXXXXXXX: Data Station No.00-05 : 1200 bps

06 : 600 bps

07 : 1200 bps

08 : 2400 bps

09 : 4800 bps

10 : 9600 bps

11 : 19.2 kbps

12 : 48 kbps

13 : 56 kbps

14 : 64 kbps

15 : 7200 bps16 : 14.4 kbps

17-31 : 1200 bps

(1)

(2)

YY=05 Parity CheckX-XXXXXXXX: Data Station No.0 : Effective

1 : Ineffective

(1)

(2)

YY=06 Synchronous/Asynchronous


0 : Synchronous

7 : Asynchronous

(1)

(2)

YY=07 Transmission Mode


0 : Half Duplex

1 : Full Duplex

A

B

CMA1


57/100



DESCRIPTION DATA

(1)

(2)

YY=08 Stop Bit


0 : 2-Stop Bit

1 : 1-Stop Bit

(1)

(2)

YY=09 Type of Code


00 : ASCII (7-bit) + even parity

01 : ASCII (7-bit) + odd parity

02 : ASCII (7-bit) + parity (0)

03 : ASCII (7-bit) + parity (1)

04 : JIS (7-bit) + even parity

05 : JIS (7-bit) + odd parity

06 : JIS (8-bit)

07 : EBCDIC (8-bit)

15 : Non character (Binary Data)

(1)

(2)

YY=19 S Buffer


0 : Effective

1 : Ineffective

Provide the Nailed-Down Connection with

the connecting patterns.

(1)

(2)

YYY=00-99, 000-199

Memory Block 00-99, 000-199

X-XXXXXXXX: Data station No.

assigned byCM1A

DXXX : Trunk No.

assigned

by CM07

X-XXXXXXXX: Data station No.

assigned by

CM1A

DXXX : Trunk No.

assigned

by CM07

CMA1

B

END

CMA5

1ST

DATA

(1)

2ND

DATA

(2)

Data station to Data

station

X-XXXX

XXXX

X-XXXX

XXXX

Data station to trunk X-XXXX

XXXXDXXX

Trunk to trunk

(Tandem Connection)DXXX DXXX

1ST AND 2NDDATA

CONNECTINGPATTERN

Seelefttable


58/100


CHAPTER 3 SYSTEM DATA PROGRAMMINGDigital Trunk Interface Assignment

DIGITAL TRUNK INTERFACE ASSIGNMENT

DESCRIPTION DATA

Assign an AP number to the DTI card.

The AP number must match the SENSEswitch setting on the DTI card.

(1)(2)

Y=0

04-15, 20-31: AP No.09: DTI

Specify the AP highway channel for

24DTI card.

(1)

(2)

Y=1

04-15, 20-31: AP No.

0 : Expanded Highway channel

(128 time slots)

1 : Basic Highway channel

(128 time slots)

Assign trunk numbers to each channelnumber on the DTI card.

The system allocates time slots to

consecutive channels from the lowest to

the highest channel number assigned. To

minimize the number of time slots

allocated, assign trunk numbers to

consecutive channels on each card.

Never skip channels in CM07.

(1)

(2)

YY=01XX ZZ

XX: 04-15, 20-31: AP No. assigned by

CM05 Y=0

ZZ: 00-23: Channel No. of 24DTI

01-15, 17-31: Channel No. of

30DTI

D000-D255: Trunk No.

Any trunk number already assigned by

CM10 cannot be used.

CM07

START

CM05

A

INITIAL

INITIAL

INITIAL


59/100



DESCRIPTION DATA

Assign the necessary functions to the

24DTI card.

After entering the data, set the MB switch

on the DTI card to UP, and then to

DOWN, for DTI initialization.

(1)

(2)

(1)

(2)

(1)

(2)

(1)

(2)

YY=00 Data Mode

04-15, 20-31: AP No. assigned byCM05 Y=0

0: Based on AT&T Spec.

YY=01 Frame Configuration

04-15, 20-31: AP No. assigned by

CM05 Y=0

0 : 12-Multi Frame

1 : 24-Multi Frame

YY=02 Zero Code Suppression

04-15, 20-31: AP No. assigned byCM05 Y=0

1 : Not available (Transparent)

YY=03

04-15, 20-31: AP No. assigned by

CM05 Y=0

7 : Associated Channel Interoffice

Signaling

Assign a trunk route number for tie line

interface to each DTI.

NOTE: The DTI route must be separatedfrom any analog trunk route.

(1)

(2)

YY=00

000-255: Trunk No. assigned by CM07Y=01

00-63: Trunk Route No.

Assign trunk route data to each DTI route.

(1)

(2)

YY=00 Kind of Trunk Route


04: Tie Line trunk

(1)

(2)

YY=01 Dialing Signal Type


7 : DP/DTMF (Incoming)DTMF (Outgoing)

CMAA

A

CM30

CM35

B

DTI INITIAL


60/100



DESCRIPTION DATA

CM35 Y=19 DTI PAD

[For Australia]

[For North America/Other Countries]

(1)

(2)

YY=04

Answer Signal from distant office00-63: Trunk Route No.

2: Answer signal arrives

(1)

(2)

YY=05

Release Signal from distant office


1 : Release signal arrives

(1)

(2)

YY=09 Incoming Connection Signaling


03: Wink Start

04: Delay Dial

05: Immediate Start

06: 2nd DT/Timing Start-Tie Line

(1)

(2)

YY=19 DTI Pad


0-3: Programmable PAD by CM42

4-7 : Fixed PAD (See left table)

(1)

(2)

YY=20 Sender start condition


00 : Wink Start01 : Delay Dial

02 : Ground Start

15 : Timing Start

(1)

(2)

YY=89 Cyclic Redundancy Checking

for Bit Error Detection


0: To provide

CM35

B

C

T/R: Transmitter PAD/Receiver PAD

CONNECTION

PATTERNS

PAD DATA OF DTI [dB]

DATA

=4

(T/R)

DATA

=5

(T/R)

DATA

=6

(T/R)

DATA

=7

(T/R)

Station-DTI 0/0

Tone-DTI 0/0

COT/DID/LDT-DTI 0/0

ODT-DTI 0/0

DTI-DTI 0/0

T/R : Transmitter PAD/Receiver PAD

+ : Gain

: Loss

CONNECTIONPATTERNS

PAD DATA OF DTI [dB]

DATA=4 (T/R)

DATA=5 (T/R)

DATA=6 (T/R)

DATA=7 (T/R)

Station-DTI 3/8 3/3 3/3 3/8

Tone-DTI 0/0 0/0 0/0 0/0

COT/DID/LDT/ODT(2W E&M)-DTI

0/0 0/0 0/0 0/0

ODT (4W E&M)-DTI

+3/3 0/0 0/0 +3/3

DTI-DTI 0/6 0/0 0/6 0/0


61/100



DESCRIPTION DATA

Specify the kind of digital data

transmission.

(1)(2)

YY=92


0 : Digital Data Transmission

(48 kbps)


(56 kbps)


(Transparent)

3 : Reversal of F&S Bits

7 : Data Transmission via Modem

CM35

C

END


62/100


CHAPTER 4

OPERATION TEST

This chapter explains the operation tests to be performed after you

have completed the installation of the Data Interface to the PBX.


63/100


CHAPTER 4 OPERATION TESTDPC Loopback Test

DPC LOOPBACK TEST

This test is the intra-office loopback test on the DPC card using a modem tester. There are two

kinds of loopback (Loopback 1, Loopback 2) as shown in Figure 4-1. Either the Loopback 1 or

the Loopback 2 can be selected by switch settings on the DPC card.

Figure 4-1 DPC Loopback Tests

V.110

DPC

V.110

DPC

Loopback 1 PBX

MODEM TESTER

DTI

Loopback 2

MODEM TESTER

DTI

NOTE: The modem tester is locally provided.


64/100



DPC Loopback 1 Test

(1) Set the SW1 on the DPC card as shown below.

(2) Confirm whether the LB01 lamp (for No. 0 circuit) or the LB11 lamp (for No. 1 circuit) on the

DPC card lights.

If the LB01 lamp or the LB11 lamp does not light, check the switch settings on the DPC card

and the system data assignment.

(3) Connect a modem tester to the DPC card as shown in Figure 4-2.

Figure 4-2 Connection of Modem Tester

For No. 0 Circuit For No. 1 Circuit

4

3

2

1

OFF

ON

SW1

4

3

2

1

OFF

ON

SW1

: POSITION TO BE SET

MODEM TESTER

DPC

PBX

(J) (P)

STRAIGHT CABLE DPC V11 CABLE

(P) (J)

XCN0 (FOR No. 0 CIRCUIT)/XCN1 (FOR No. 1 CIRCUIT)

(a) When you use V. 11 (X.21) interface

MODEM TESTER

DPC

PBX

(J) (P)

STRAIGHT CABLE DPC RS CABLE

(P) (J)

RS0 (FOR No. 0 CIRCUIT)/RS1 (FOR No. 1 CIRCUIT)

(b) When you use V. 24/V. 28 (RS-232C) interface


65/100



(4) Set the attributes of modem tester (transmission rate, etc.).

(5) To confirm whether the data is transmitted correctly, send the PN Pattern 9 (511 Pattern)

from the modem tester.

(6) Count bit errors on the modem tester for 1 minute.

If bit errors do not occur, the cable connection between DPC card and modem tester is

normal.

(7) If bit errors occur, check the cable connection, and replace the DPC card.

(8) After this test, set all the SW1-1 through SW1-4 on the DPC card to OFF.


66/100



DPC Loopback 2 Test

After you complete the DPC Loopback 1 Test, do the following steps.

(1) Set the SW1 on the DPC card as shown below.

(2) Confirm whether the LB02 lamp (for No. 0 circuit) or the LB12 lamp (for No. 1 circuit) on theDPC card lights.

If the LB02 lamp or the LB12 lamp does not light, check the switch settings on the DPC card

and the system data assignment.

(3) Connect a modem tester to the DPC card as shown in Figure 4-2 Connection of Modem

Tester.

(4) Set the attributes of modem tester (transmission rate, etc.).


from the modem tester.

(6) Count bit errors on the modem tester for 1 minute.

If bit errors do not occur, the DPC card is normal.

(7) If bit errors occur, check the system data assignment, and replace the DPC card.

(8) After this test, set all the SW1-1 through SW1-4 on DPC card to OFF.

For No. 0 Circuit For No. 1 Circuit

4

3

2

1

OFF

ON

SW1

4

3

2

1

OFF

ON

SW1

: POSITION TO BE SET


67/100


CHAPTER 4 OPERATION TESTOther Loopback Tests

OTHER LOOPBACK TESTS

Two additional forms of loopback test are shown in Figure 4-3.

Figure 4-3 Other Loopback Tests

V.110

DPC

DTI local loopback PBX

DTI

DTI hard-wired loopback

Set DTI in localloopback.

DTI

TATB

RARB

On the MDF, connect

transmit leads to the

Receive leads to test

all portions of the DTI.

V.110

DPC

MODEM TESTER

MODEM TESTER


68/100

CHAPTER 4 OPERATION TESTInter-Office Digital Data Transmission Test


INTER-OFFICE DIGITAL DATA TRANSMISSION TEST

This test is the inter-office digital data transmission test using modem testers. After you complete

the loopback tests, do the following steps.

(1) Connect modem testers to the both PBXs as shown in Figure 4-4.

Figure 4-4 Inter-Office Digital Data Transmission Test

(2) Set the attributes of both modem testers (transmission rate, etc.).

NOTE: If both the attributes do not match, this test is not available.


from the modem testers.

(4) Count bit errors on the modem testers for 1 minute.

If bit errors do not occur, the inter-office digital data transmission is normal.

(5) If bit errors occur, check the following items.

System data assignment DTI card

PCM digital line

Opposite PBX

PBXPBX

MODEM TESTER

DTIDPC DTI DPC

MODEM TESTER

24/30 CHANNELPCM DIGITAL LINE

NOTE 1: For details of cable connection between the DPC card and the modem tester, see

Figure 4-2 Connection of Modem Tester.

NOTE 2: The modem tester is locally provided.

NOTE 1 NOTE 1


69/100


CHAPTER 5

CIRCUIT CARDINFORMATION

This chapter explains the mounting location, the meaning of lamp

indications, and the method of switch settings of each circuit card for

the Data Interface system.


70/100


CHAPTER 5 CIRCUIT CARD INFORMATIONHow to Read This Chapter

HOW TO READ THIS CHAPTER

This chapter explains each circuit card used in this system for the following items. Explanations

are given in the alphabetical order of the circuit card names within each circuit card category

(Control, Application Processor, and Line/Trunk).

(1) Locations of Lamps, Switches, and Connectors

The locations of lamps, switches, and connectors of each circuit card are shown by a face

layout.

(2) Lamp Indications

The name, color, and functions of each indicator lamp equipped on each circuit card are

described in a table.

(3) Switch Settings

The name, settings, and functions of each switch equipped on each circuit card are

described in a table.

Each switch setting table has a CHECK column. Make necessary entries in the CHECK column

during and/or after the system installation and maintenance, and use each table as a reference

for subsequent system maintenance and operations.


71/100

CHAPTER 5 CIRCUIT CARD INFORMATIONMounting Location of Circuit Card


MOUNTING LOCATION OF CIRCUIT CARD

This section explains the conditions for mounting circuit cards for the Data Interface.

Figure 5-1 shows circuit card mounting slots allocated in the PIM.

Figure 5-1 Mounting Location of Circuit Card

*1 PN-CP14 (MP) card on the MP12 slot on PIM0.

*2 PN-24DTA-C/PN-30DTC-A (DTI) card on the AP00-AP11 slots on PIM0-PIM7.

*3 PN-2DPCB (DPC) and PN-M03 (M03) card on the LT00-LT11 slots on PIM0-PIM7.

*4 PZ-M542/PZ-M557 (CONN) card on the LTC0-LTC3 connectors on the PIM which

accommodates 30DTI card.

LT09/AP09

LT08/AP08

LT07/AP07

LTC1LTC0 LTC2

BWB

PIM

0~7

FRONT

AC/DC

PWR

LT10/AP10

LT00/AP00

LT01/AP01

LT02/AP02

LT03/AP03

LT04/AP04

LT05/AP05

LT06/AP06

LT11/AP11/FP11

MP12/FP12

LTC3

DC/DC

PWR

PFT

VM

*2, *3*1

*4


72/100


CHAPTER 5 CIRCUIT CARD INFORMATIONList of Required Circuit Cards

LIST OF REQUIRED CIRCUIT CARDS

Table 5-1 shows the required circuit cards to be explained in this section.

*MB = Make Busy

Table 5-1 List of Required Circuit Cards

NAME

(FUNCTIONAL

NAME)

LAMP

X:PROVIDED

: NOT

PROVIDED

SWITCH

X:PROVIDED

: NOT

PROVIDED

EXTRACTION/

INSERTION WITH

POWER ON

X:ALLOWED

: ALLOWED

AFTER MB*

: NOT ALLOWED

REFERENCE

PAGE

PN-CP14 (MP) X X Page 67

PN-24DTA-C (DTI) X X Page 72

PN-30DTC-A (DTI) X X Page 78

PZ-M542 (CONN) X X Page 84

PZ-M557 (CONN) X X Page 86

PN-2DPCB (DPC) X X X Page 88

PN-M03 (M03) X X X Page 92


73/100

CHAPTER 5 CIRCUIT CARD INFORMATIONList of Required Circuit Cards


PN-CP14 (MP)

Locations of Lamps, Switches, and Connectors

CONN: To CONNR connector on PZ-M537 (EXPMEM)

Lamp Indications

LAMP

NAMECOLOR FUN

NEAX2000 IVS2 Data Interface System Manual

Documents