NATURAL STONE APPLICATION FOR INTERIORS
Sep 14, 2014
NATURAL STONE APPLICATION FOR INTERIORS
OVERVIEW
Types of Natural Stone and Tile Quarrying Cuts and Matching Finishes Stone Construction Considerations When Specifying Maintaining Natural Stone Installation Examples
NATURAL STONE TYPES: TRAVERTINE
Character: has voids, usually has some veining, variety of colors (mostly in the warm range). Formation: Travertine is a sedimentary rock formed by the precipitation of carbonate minerals. Applications:
Floor and Wall Generally not chosen for kitchen countertops due to its low density, but travertine makes a
beautiful countertop in a bathroom A popular choice for outdoor use; especially as cladding , pavers, or as pool surrounds.
Travertine is naturally water ‘resistant” as it tends to push water out due to the way the stone is formed.
Be sure to specify 1st choice travertine for most interior applications. This is the most dense material. Commercial grade travertine is much cheaper, but can be very sandy, disintegrate, and have large holes. Commercial grade may be appropriate for outdoor use in some cases—but not where erosion may be a concern.
NATURAL STONE TYPES: LIMESTONE
Character: often has visible fossils embedded within, some color variety. Formation: Limestone is a sedimentary rock composed of different crystal forms of calcium
carbonate. Most grains in limestone are skeletal fragments of marine organisms Application
Floor and wall Not generally chosen for countertops due to its porosity and tendency to stain-- limestone is
suitable for bathroom countertops, however. Not generally chosen for outdoor use for the same reasons, but it can be used with proper sealing Some limestones must be sealed from the front AND the back before installation to prevent the
setting materials from staining the stone.
NATURAL STONE TYPES: MARBLE
Character: Marble often has distinct veining with a wide variety of colors. Formation: Marble is a metamorphic crystalline rock formed when limestone has additional
heat and pressure applied to it by the earth’s crust, causing the stone to re-crystallize. Applications:
Floor and Wall Countertops—occasionally. It is a popular material for bathroom countertops. It Can be too
delicate for kitchen (depending on how the client will use it) New Sealing Products have made marble a more popular choice for interior countertops in recent years.
Not usually a good choice for outdoor applications. Can be used in a sandblasted or other highly textured finish, but usually not preferred for countertops in outdoor kitchens or in wet areas.
NATURAL STONE TYPES: GRANITE
Character: often has “busy” visual texture in a variety of colors. Formation: Granite is a plutonic igneous rock having visibly crystalline texture;
generally composed of feldspar and mica and quartz Applications:
Floor and wall: sometimes this is a desired look, but it can be very busy Countertops: the hardness of the stone makes granite the most popular choice for
both kitchen and bathroom countertops. Suitable for any outdoor applications (be careful to choose the right finish) and
exterior cladding
NATURAL STONE TYPES Slate
Character: rough texture, mostly greys, but some varieties have dramatic some color variation.
Formation: Slate is a fine-grained, foliated, homogeneous metamorphic rock derived from an original shale-type sedimentary rock composed of clay or volcanic ash
Applications: Floor and wall: must consider shaling when choosing slate Not generally used as kitchen countertops due to shaling,
but custom slab fabrication is available Great for outdoor use
Quartzite Character: Looks similar to slate, but is harder and doesn’t shale Formation: a very hard metamorphic rock consisting of a mosaic of intergrown
quartz crystals Applications: Same as slate
NATURAL STONE TYPES Onyx
Character: translucent, can range from gold and oranges to green. Formation: Onyx is a cryptocrystalline form of quartz. Onyx is a
sedimentary rock, formed as stalactites and stalagmites in cave interiors.
Applications Floor, Wall and decorative. Onyx can be delicate, so be careful where you use it. Most popular for Vanity countertops or specialty surfaces
Soap Stone Character: Grey, sometimes greenish. With white veining. Smooth “soapy” feel Formation: a metamorphic rock that is largely composed of the mineral talc Applications:
Generally used for countertops Chemical and heat resistant but NOT scratch resistant Can be delicate—must be oiled regularly to keep color
STONE PRODUCTION Sourcing
Natural stone comes from quarries world-wide. Certain stones are available only in certain
parts of the world. Italy, Spain, and Turkey are major exporters of
different types of natural stone Quarries
After a deposit of a desired stone is discovered, engineers design a quarry plan
Stone is excavated using drilling and blasting techniques
Long tunnels are drilled vertically Explosives are inserted and detonated Large boulders are removed and processed
into useable tile and slabs at the factories Let’s watch a quarry blast!
Factories Large blocks from the blast are either cut into
specialty items like sinks, bathtubs, etc, or cut into large slabs which are then planed and cut into tiles
Factories have specially calibrated machinery to make 90 degree corners and straight cuts. Be sure when purchasing that tile is properly calibrated!
How Granite is sourced and produced
CUT TYPES AND MATCHING Cross Cut: stone is cut parallel to
natural layers, creating a cloudy movement in the grain
Vein Cut: stone is cut perpendicular to natural layers, creating a linear movement in the grain
Random Match: A casual, unmatched effect with no attempt at a pattern (most common application)
Book Match: a mirrored-image pattern at the joint line that produces a nearly continuous grain.
Variations of Book matching include: end matching, diamond matching, and quarter matching. These are all special order because the factory must recalibrate the machinery to produce this effect.
NATURAL STONE FINISHES Polished: A glossy surface finish that brings out the full color and character of the stone. The finest and smoothest
finish available in stone, characterized by a high luster and strong reflection of light.
Honed: This is a process to remove the saw marks/scratches left by the saw. This gives a softer, matte appearance to the stone.
Honed and Filled: Before Travertine is honed, the natural holes are often filled with colored cement or resin to create a smooth surface
Brushed: This process is done with a wire brush to make the stone have a soft or velvet feel to it. This process enhances and deepens the colors as well. Sometimes called “leather’ finish.
Tumbled: A special finish obtained by rotating pre-cut pieces of stone in a tumbler. This process produces a very rustic look with rough edges and rounded corners.
Sand Blasted: This is accomplished by exposing the surface to a high pressure jet of sand that leaves the material slightly scratched on the surface. This finish is often used outside because it is non-skid.
Flamed: A stone that has been thermally treated, creating a reddish-yellow color with uneven rough surface. Saw-Cut: This is the result when the stone is cut; the gang saw used leaves marks/scratches on the surface. Bush Hammered: A finish that creates a rugged surface full of little grazes that becomes non-slippery, also giving
the stone a lighter shade. Split: Tile has a flat back with an uneven front surface, which offers a look like protruding bricks from the wall. Chiseled: A hand-made finish with deep textured line that could go in one or more directions. Can be rough or fine. Antiqued: Special machines that look like industrial washing machines are used to treat the pieces with abrasive
elements (sand, shot blast) while a cylinder revolves. In a short time the impact on the stones with the abrasives produces an effect similar to aging caused by use and wear.
Acid Washed: Stone is treated with a special acid to create a slightly textured finish—this is popular in shower areas, especially in stone shower trays. Can also be used to remove a polished finish from stone.
Imitations of these finishes are often available in man-made and engineered surfaces, as well as porcelain and ceramic tile
TYPES OF STONE CONSTRUCTION Rubble
Stones are used as they are, or roughly shaped and laid with wide joints. Cobblestone
Cobblestones are laid in horizontal rows with decorative mortar treatment to the horizontal and vertical joints.
Ashlar Quarried stone is sawn to a particular size and the blocks fit closely
together
RUBBLE CONSTRUCTION
COBBLESTONE CONSTRUCTION
ASHLAR CONSTRUCTION
TYPES OF STONE WALLS Structural
- footing needed - coursed or non-coursed - filled with mortar - minimum 10” thick
Decorative - footings still needed - coursed or uncoursed - fill with mortar - metal ties fasten decorative
to structural wall
FOOTINGS FOR STONE WALLS
METAL TIE SYSTEM FOR DECORATIVE STONE WALLS
Barnes Foundation on Ben Franklin Parkway
SPECIFICATION CONSIDERATIONS Residential
Almost any finish is appropriate for any application—it’s all about the preferred look Sometimes slipperiness is a client concern in wet areas when using polished stone—the abrasion
coefficient between polished and matte is not so great that this is an issue on paper (many commercial applications use polished stone), but be sure to address any concerns with clients before specifying a material.
Dust often makes stone more slippery than wetness—be sure to tell clients to dust mop their natural stone floors regularly
Textured finishes (split) look great for walls, but be sure to explain to the client how to clean them (using a soft brush and stone cleaner). Consult your stone supplier for installation instructions in wet areas.
Shower Floors: Must have small mosaics (most contractors prefer 2X2 or smaller, although 4X4 can work) UNLESS a linear drain is used
Commercial There is far more regulation in commercial applications regarding slip resistance and abrasion. Be sure
to know your city’s or client’s codes regarding these requirements. Thickness of Tiles
Unlike porcelain tile, natural stone tiles vary in thickness from size to size (large format tiles must be thicker to prevent breakage.) Be sure when combining tile sizes to be aware of the difference in thickness as this will add to the labor.
Sealer Natural stone should be sealed at the time of installation to prevent staining. Some people may
prefer to re-seal periodically for various reasons Sealer does not create a shiny finish or effect slip resistance. It creates a water-tight barrier,
strengthens stone, and sometimes adds a “wet-look” which enhances the color
MAINTAINING NATURAL STONE DO seal the area to bring out the color of the stone. DO blot up spills immediately. DO clean surfaces using only a soft cloth or sponge. DO use a stone cleaner DO thoroughly rinse and dry the surface after washing. DO dust mop natural stone floors regularly. DO protect floor surfaces with non-abrasive non-slip mats or area rugs.
DON’T use vinegar, lemon juice or other acid-containing cleaners on natural stone. DON’T use rough cloths and mops to clean stone floors. DON’T use vacuum cleaners, as the metal or plastic attachments/wheels may scratch the floor. Don't use cleaners that contain acid such as bathroom cleaners, grout or tub & tile cleaners.
Don't use abrasive cleaners such as dry cleansers or soft cleansers.
Regular maintenance using the correct techniques and products will ultimately preserve natural stone flooring and reduce the need for very costly refurbishment.
The Coliseum in Rome is constructed of travertine and still stands today. The oldest stone floor in Britain, one made of limestone, is around 7,000 years old and still
in remarkably good condition.
That should be durable enough for anyone.
INSTALLATION EXAMPLES
Slab Wall Treatment
- installed with metal fasteners- grout is usually 1/16” in a custom color- pattern is a consideration
Hyatt Lobby, Austin Texas
INSTALLATION EXAMPLES
INSTALLATION EXAMPLES
Mocha Onyx Travertine in Roman Pattern in Living Area
INSTALLATION EXAMPLES
Travertine Roman Pattern in a Restaurant
INSTALLATION EXAMPLES
24X24 Pearl Limestone in a Dining AreaRe-finishing the tile after installation creates the look of one sheet of
stone on the floor
INSTALLATION EXAMPLES
Silver Ivory Travertine in a High-End Retail Store (Coach, Verizon Center)
INSTALLATION EXAMPLES
16x24 Honed Travertine with Chiseled Edges installed on an Angle.
Tumbled Limestone Backsplash
INSTALLATION EXAMPLES
Mocha Onyx Travertine Roman Pattern and Steps in a Restaurant
(Madison Café, Riverton NJ. Design by Wendy Holden, ASID)
INSTALLATION EXAMPLES
Saw Cut Travertine Exterior Cladding (El Salvador)
INSTALLATION EXAMPLES
Custom Marble Pieces, including moldings, columns, and solid piece bench supports
INSTALLATION EXAMPLES
Custom Travertine Shower Tray with Split-face Accent Wall
INSTALLATION EXAMPLES
Splitface Mosaics can be installed in a shower area without grout—proper waterproofing with membranes and specialty thinsets were used
INSTALLATION EXAMPLES
Usually Shower Floors MUST have 4x4 or Smaller Mosaics (Due to Sloping)
A Specialty Drain will Allow for Large tiles and ADA Accessibility
INSTALLATION EXAMPLES
This Vertical Accent was Created for Practical Reasons:Can you Guess Why?
FOR YOUR INFORMATION www.stonemar.com
[email protected] www.marble-institute.com www.laticrete.com/architects.aspx www.natural-stone-database.com www.architonic.com