Multiconn Multiconn Srl Srl BMW - iDRIVE Professional Navigation CCC (1-2 buttons) BMW - iDRIVE Professional Navigation CCC (1-2 buttons) www.dasdvbt.com www.dasdvbt.com Installation and User Manual Installation and User Manual ver.1.0 ver.1.0 [to integrate with the user manual of DAS M32/M44] [to integrate with the user manual of DAS M32/M44] Fiber Optic Fiber Optic
10
Embed
Multiconn Srl BMW - iDRIVE Professional Navigation CCC (1-2 buttons) Installation and User Manual ver.1.0 [to integrate with the user manual.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Multiconn SrlMulticonn Srl
BMW - iDRIVE Professional Navigation CCC (1-2 buttons)BMW - iDRIVE Professional Navigation CCC (1-2 buttons)
www.dasdvbt.comwww.dasdvbt.com
Installation and User Manual Installation and User Manual ver.1.0ver.1.0 [to integrate with the user manual of DAS M32/M44][to integrate with the user manual of DAS M32/M44]
Fiber OpticFiber Optic
Multiconn SrlMulticonn Srl 2
Installation:Installation:
WARNING:WARNING: before installing the DASbefore installing the DAS®® tuner verify that the system of the car MUST be professional and not tuner verify that the system of the car MUST be professional and not Business. With Business system the TV tuner does not work.Business. With Business system the TV tuner does not work.To unlock the system use an interface or contact directly an official BMW center.To unlock the system use an interface or contact directly an official BMW center.
BMW – CCC systemBMW – CCC system
1. To install the DASDAS®® receiver, refer to the specific user manual;
Pay attention on the connection of the power supply cablePay attention on the connection of the power supply cable::
- RED wire (fig.3) must be RED wire (fig.3) must be DISCONNECTEDDISCONNECTED.. The switch (ON/OFF) of the receiver will be controlled by the Fiber-Optic activityThe switch (ON/OFF) of the receiver will be controlled by the Fiber-Optic activity
- YELLOW wire (fig.1)(fig.1) must be connected to the +12V permanent/battery- BLACK wire (fig.2)(fig.2) must be connected to the GND.
Power supply cable
11
22
33
2. Disconnect the original Fiber Optical cable (fig.4)(fig.4) from one of the original multimedia accessories inside the car (DVD, GPS, Amplifier, etc…) and match it directly to DASDAS®® fiber optic female connector of the harness on equipment (fig.5)(fig.5).
44 44 55
3. Match the two other connectors of DASDAS®® harness (fig.6)(fig.6) respectively inside the original accessory (fig.7)(fig.7) and the other one inside DASDAS®® receiver (fig.8)(fig.8).
Multiconn SrlMulticonn Srl 3
7777 88
66
55
88
99
88
99
4. Connect one of the 3 DASDAS®® Video-OUT (fig.8)(fig.8) trough the adapter cables on equipment (fig.9) and the needed accessory (fig.9) and the needed accessory with white Fakra connector (DCABMQS-RCA in fig.9.1) (DCABMQS-RCA in fig.9.1) with the Video-IN on the CCCCCC Unit (fig.10)(fig.10).
99.1.1
DASDAS Video-OUT
BMW – CCC systemBMW – CCC system
Video-IN
Multiconn SrlMulticonn Srl 4
The CCCCCC unit location on dashboard (fig.10)(fig.10) and the rear side (fig.11).fig.11).
1010
99.1.1
1111
Insert the 2 female crimped pins of DASDAS cable (fig.9.1 fig.9.1 DCABMQS-RCA) inside the black 12P housing and then in white Fakra cover.If the connectors are already available in the unit, just connect the pins in the pin-out position recommended below.
Insert the wire with label ++ in pin 4pin 4 (positive signal).
Insert the wire with label -- inside the pin 2pin 2 (negative signal).If the pin 2 and 4 are already used by the rear camera, disconnect them and and connect to a yellow RCA to video-IN 1 on DASDAS receiver.
To shift automatically the signal from TV to REAR CAMERA, To shift automatically the signal from TV to REAR CAMERA, connect the green wire of the power supply cable (refer to the connect the green wire of the power supply cable (refer to the DAS DAS user manual) directly to the rear camera installed inside the vehicle.user manual) directly to the rear camera installed inside the vehicle.
BMW – CCC systemBMW – CCC system
User Manual:User Manual:
Multiconn SrlMulticonn Srl 5
Before coding the TV function using an aftermarket OBD interface, please check if the OEM start-up screen (with logo BMW) has a background grey/silver colour (fig.12)(fig.12); if the colour is brown (fig.13)(fig.13) go directly to an official BMW service to upgrade the entertainment software of the car.
1212
1313
brown colourbrown colournecessary upgrade the software necessary upgrade the software in a BMW servicein a BMW service
BMW – CCC systemBMW – CCC system
Multiconn SrlMulticonn Srl 6
To enter in DASDAS TV tuner with the iDrive select Enterntainment Enterntainment and select TVTV (like the original TV Tuner).
WARNING:WARNING: For the basic settings such as color, contrast, brightness and format, please refer to the menu of the For the basic settings such as color, contrast, brightness and format, please refer to the menu of the car and make sure that the format is congruent with the set menu on the DAS.car and make sure that the format is congruent with the set menu on the DAS.
BMW – CCC systemBMW – CCC system
With the CCC platform, we can find 2 iDrive versions:
- ControlledControlled: where iDrive rotation is bound, not free;- Free runningFree running: where iDrive rotation is free in both directions;
To use the iDrive “controlled”controlled” in “free running”free running” mode, operate in the following way:
Press the iDrive after to have selected TV; Then will appear a graphic overlay with AutostoreAutostore message;Wait 2/3 seconds till the message AutostoreAutostore disappears;by this time the iDrive is changed in “free running”free running”
Important: the other menu of the car are now not availableImportant: the other menu of the car are now not available
To return in controlled mode and use the other menu of the car, press the iDrive again.
Multiconn SrlMulticonn Srl 7
CCC iDrive controllerCCC iDrive controller
CCC iDrive controllerCCC iDrive controller
Right rotation = UPon remote control (dropdown menu)
Left rotation = Down on remote control (dropdown menu)
Down Joystick Scroll= OK/Menu
Right Joystick Scroll=Right arrow on remote
Left Joystick Scroll=Left arrow on remote
BMW – CCC systemBMW – CCC system
PUSH
Multiconn SrlMulticonn Srl 8
Remote Control Functions:Remote Control Functions: