2. Turn off engine and drain engine oil using a Jabsco drill pump and hose kit (Model 17215-0000). To pump the oil out of engine, insert the probe to the inside bottom of the engine through the dipstick tube. (You may also drain your engine oil by what- ever method you have previously used). 3. Remove the oil drain plug from your engine, catching the final drips of oil with a cardboard sheet. 4. Wrap threads of hex drain fitting with Teflon* tape, or apply thread compound. Make sure nylon washer is in place between engine pan and hex drain fitting. Install hex drain fitting in pan securely. Wrap threads of black drain hose fitting with Teflon tape or apply thread compound. Install black drain hose in PERMANENT OIL DRAIN HOSE AND FITTING Explosion hazard. Take necessary precautions to ventilate area around battery of potentially explosive gases. Continue ventilation during oil changing procedure. Failure to do so can result in explosion. Injury or death can occur. . WARNING ! Oil drain fitting and oil drain hose must be tightened securely to prevent fittings from loosening and causing an oil leak that can damage engine. Install cap securely on free end of drain hose. Cap Bulkhead Or Firewall Hose Hanger Oil Drain Hose End Hose Hanger Screw Engine *Teflon is a registered trademark of E.I. DuPont de Nemours and Company. 1. Run engine at idle speed for about 5 minutes to warm the engine oil. Burn hazard. Heated oil can cause burns. Wear protective gloves, clothing and safety glasses during the oil change process. Failure to do so may result in personal injury. 5. Locate drain hose on vertical bulkhead or firewall and secure with plastic hose hanger. Do not kink hose or locate so that it touches the engine. See that all fittings are tightened securely. Installation is now complete. REFILL ENGINE WITH REQUIRED QUANTITY OF MOTOR OIL. CAUTION ! Nylon Washer 1/4”NPT Pipe Plug Wrap With Teflon Tape Hex Drain Fitting With 1/2” X 20 Straight Thread Oil Drain Fitting Oil Drain Hose hole in oil drain fitting which will provide the most direct path to convenient hanger location on vertical bulkhead or firewall. Wrap plug with Teflon tape or apply thread compound and install in remaining hole, securely. Install cap securely on free end of drain hose. MODEL 18080-0000
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
2. Turn off engine and drain engine oil using a Jabscodrill pump and hose kit (Model 17215-0000). Topump the oil out of engine, insert the probe to theinside bottom of the engine through the dipsticktube. (You may also drain your engine oil by what-ever method you have previously used).
3. Remove the oil drain plug from your engine, catching the final drips of oil with a cardboard sheet.
4. Wrap threads of hex drain fitting with Teflon* tape, orapply thread compound. Make sure nylon washer isin place between engine pan and hex drain fitting.Install hex drain fitting in pan securely. Wrap threadsof black drain hose fitting with Teflon tape or applythread compound. Install black drain hose in
PERMANENT OIL DRAINHOSE AND FITTING
Explosion hazard. Take necessary precautions to ventilate area around battery of potentially explosive gases. Continue ventilation during oil changing procedure. Failure to do so can result in explosion. Injury or death can occur..
WARNING!Oil drain fitting and oil drain hose must betightened securely to prevent fittings fromloosening and causing an oil leak that candamage engine. Install cap securely on freeend of drain hose.
Cap
Bulkhead Or Firewall HoseHanger
Oil Drain Hose End
Hose Hanger
Screw
Engine
*Teflon is a registered trademark of E.I. DuPont de Nemours and Company.
1. Run engine at idle speed for about 5 minutes towarm the engine oil.
Burn hazard. Heated oil can cause burns.Wear protective gloves, clothing and safetyglasses during the oil change process.Failure to do so may result in personal injury.
5. Locate drain hose on vertical bulkhead or firewalland secure with plastic hose hanger. Do not kinkhose or locate so that it touches the engine. See thatall fittings are tightened securely. Installation is nowcomplete.REFILL ENGINE WITH REQUIRED QUANTITY OFMOTOR OIL.
CAUTION !
Nylon Washer1/4”NPTPipe Plug Wrap With
Teflon Tape
Hex Drain FittingWith 1/2” X 20Straight Thread
Oil DrainFitting Oil Drain
Hose
hole in oil drain fitting which will provide the mostdirect path to convenient hanger location on verticalbulkhead or firewall. Wrap plug with Teflon tape orapply thread compound and install in remaininghole, securely. Install cap securely on free end ofdrain hose.
MODEL 18080-0000
1. Run engine for about 5 minutes, then turn off. (Seeprevious warning notes).
2. Remove plastic adaptor from suction hose of Porta-Quick oil changer.
3. Slip Porta-Quick suction hose over threaded metalfitting of oil drain hose, after removing cap.
4. Connect alligator clips to a 12 volt dc battery.5. Switch on to pump oil from engine to the Porta-Quick
container. Motor will speed up when oil is removedfrom engine. Switch off immediately.
6. Disconnect the oil drain hose, replace cap andsecure hose with hose hanger to bulkhead. Be surehose is securely mounted.
7. Refill engine with required quantity of motor oil.8. Used engine oil may be disposed of at any service
station.
Explosion hazard. Motor switch must be in "OFF" position when connecting and disconnecting alligator clips to battery terminal and ground. The switch in an "ON" position can cause an electrical spark which can result in explosion. Injury or death can occur .
W ARNING !
THE PRODUCT DESCRIBED HEREINIS SUBJECT TO THE JABSCO ONEYEAR LIMITED WARRANTY, WHICH ISAVAILABLE FOR YOUR INSPECTIONUPON REQUEST.
In many installations, the above mentioned gravity drainmethod is not possible in which case the following willapply: Use the Jabsco electric drill pump kit (Model17215-0000).1. Run engine for about 5 minutes, then turn off. (See
previous warning notes).2. Attach a short length of 1/2" ID Neoprene hose to
suction port of drill pump.3. Attach discharge hose to discharge port of drill pump.4. Slip pump suction hose over threaded metal fitting of
drain hose, after removing cap.5. Pump oil from engine.
Cap
HoseHangerPorta-Quick
Oil ChangerPan
6. Remove pump from oil drain hose, replace cap andsecure hose with hose hanger to bulkhead. Be surehose is securely mounted.
7. Refill engine with required quantity of motor oil.
Use the 12 volt dc Jabsco Porta-Quick Oil Changer(Model 17800-1000).
Discharge HoseHose Hanger
Cap
Oil DrainHose
SuctionHose
Gallon PlasticContainers
1/4”Electric Drill
CapHose Hanger
Pan
Oil Drain Hose
CAUTION
FUTURE OIL CHANGES
Now that your Jabsco drain hose and fitting is installed,future oil changes will be simplified using the following
Burn hazard. Heated oil can cause burns.Wear protective gloves, clothing and safetyglasses during the oil change process.Failure to do so may result in personal injury.
GRAVITY DRAINIf space allows, the engine oil may be drained by gravity.1. Run engine for about 5 minutes, then turn off. (See
previous warning notes).2. Remove the hose from it’s hanger.3. Remove the tube cap, place the hose below the
level of the engine drain fitting and allow warm oil todrain into a container.
4. After oil is drained, securely recap the tube andmount it back in the hanger. Be sure hose is secure-ly mounted.
5. Refill engine with required quantity of motor oil.
Jabsco is a trademark of Xylem Inc. or one of its subsidiaries. © 2012 Xylem, Inc. 43000-0026 Rev B 10/2012
www.xylemflowcontrol.com
Related Documents
