ME FORMAT

Final Review

PROJECT TITLE

Submitted in the partial fulfillment of the requirements for the award of

MASTER OF ENGINEERING Degree inPOWER ELECTRONICS AND INDUSTRIAL DRIVESBy(NAME OF THE CANDIDATE)

(REG. No.)

DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERINGSATHYABAMA UNIVERSITY

(Established under Section 3 of UGC Act, 1956)

JEPPIAAR NAGAR, RAJIV GANDHI ROADCHENNAI 600119

APRIL 2013Project report format guidelines (both for UG/PG)

Sequence of topics to be maintained in Project Report:

Title Page

Bonafide Certificate(University format) Bonafide from the place where the work is carried out, on their letter head

Declaration-(University format)

Acknowledgement- (Order of names to acknowledge is attached

Contents with Page numbers

List of Abbreviations, if applicable

List of figure, list of tables, if applicable

Abstract of the work

Chapter 1 ,Introduction

Chapter 2, Aim and scope of present investigation

Chapter 3, Experimental or material and method ; algorithm used

Chapter 4, Results and discussion, Performance Analysis

Chapter 5, Summary and Conclusion

Bibliography/References /AppendixThe listing should be typed 4 spaces below the heading REFERENCES in alphabetical order in single spacing left-justified. The reference material should be listed in the alphabetical order of the first author. The name of the author/authors should be immediately followed by the year and other details. A typical illustrative list given below relates to the citation example quoted above.

REFERENCES

[1] Mitall. K and Trivedi. L (2007) : Title of the paper, International Journal of Physical Sciences, Vol. No: 32(3), pp.1103-1126. [2] Kannadasan .T and Gopalakrishnan .K (2009), Issues and Challenges of Academic Research in India, Manufacturing Technology and Management,Journal of IIPE, Vol.3, No.2, pp.131-138.

[3] Devadasan .S.R., et. al. (2007), Study of Various Quality Models in Engineering Educational Institutions, Proceedings of the International Conference : TEAM TECH 2007, IISc, Bangalore, India, October 4-6, pp.115-122

-For Books- name of author, title, name of editor, publisher, year, page number

-Valid internet articles

Sub chapters should be numbered as follows

Eg. Subject chapter of Chapter 1 should be numbered as 1.1, 1.2

Further sub chapter should be numbered as 1.1.1, 1.1.2.

Letter Font and line spacing to be followed throughout the project work.

Line space: 1.5, Font size: 12, Font type: Arial, Margin space: Left 3cm, Right 2.5cm, Top 2cm, Bottom 1.7cm.

Major Headings all Caps, Font size:14

Sub-headings- headings in caps, Font size 12.

Further Subheadings- 12 Font size, Bold, Italics.

Still Further sub- headings- 12 Font Size, Italics.

Legend for figures and labels-

Figure Fig: 1: Self descriptive title, 12 Font size, Italics, Bold (should be given below the figure).

Table- Table1: self descriptive title, 12 Font size, Bold (should be given above the table).

Page Numbers should be centered at the bottom of each page, starting from Introduction chapter onwards.

For Contents, Abstract, List of Abbreviations, List of figures, and list of tables the page numbers should be in the format (i), (ii), (iii).. And centered at the bottom of the page.

DECLARATION FORMATI ______________________ hereby declare that the project titled _________________________________________________________ was done by me under the guidance of ____________________________________ is submitted in partial fulfillment of the requirements for the award of MASTER OF ENGINEERING degree in POWER ELECTRONICS AND INDUSTRIAL DRIVES.

DATE:PLACE:

SIGNATURE OF THE CANDIDATE

SATHYABAMA UNIVERSITY

(Established under Section 3 of UGC Act, 1956)

JEPPIAAR NAGAR, RAJIV GANDHI ROAD, 600 119 www.sathyabamauniversity.ac.inDEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING BONAFIDE CERTIFICATEThis is to certify that this Project Report is the bonafide work of __________________[Reg.No. _____________] who carried out the project entitled ________________________________________________________________ under our supervision from November 2012 to April 2013.INTERNAL GUIDE________________________________________

HEAD OF THE DEPARTMENT (Academics)Dr. V. SIVACHIDAMBARANATHANSubmitted for Viva Voce Examination held on_________________INTERNAL EXAMINER

EXTERNAL EXAMINER

ACKNOWLEDGEMENTSThe satisfaction and elation that accompany the successful completion of any task would be incomplete without the mention of the people who have made it a possibility. It is my great privilege to express my gratitude and respect to all those who have guided me and inspired me during the course of the project work.

First and foremost, I would express my sincere gratitude to our beloved Chancellor Col. Dr. JEPPIAAR, M.A., B.L., Ph.D., and also thanks to our Directors Dr. MARIE JOHNSON, B.E., M.B.A., M.Phil., Ph.D and Tmt. MARIAZEENA JOHNSON, B.E., M.B.A., M.Phil., (Ph.D) for providing me the necessary facilities for the completion of my project. Also, I acknowledge our Vice Chancellor Dr. B.SHEELA RANI, M.S (By Research)., Ph.D. for her constant support and endorsement.

I also like to express my gratitude to Mrs. G. R. P. LAKSHMI Head of the Department (Administrative and Research) of Electrical and Electronics Engineering and Dr. V. SIVACHIDAMBARANATHAN Head of the Department (Academics) of Electrical and Electronics Engineering, Sathyabama University for having been a constant source of support and encouragement for the completion of the project.

I would also like to express my sincere thanks to my internal guide of the project ___________________ for his / her constant guidance and supervision during the period of my project work and for providing me the necessary facilities for the completion of my project.Margin space-Left 3cm, Right -2.5 cm, Top- 2cm and Bottom -1.7 cm

Arial font, size 14,

1.5 lines spacing, Centered)

Bold, Upper case Arial, size 14

Bold, Upper case Arial, size 14

Arial, Bold,20size, Upper case)

Arial, Bold,16 size, Upper case)