Log Periodic Dipole Antennas 806-960 MHz Model Number Frequency Range (MHz) H-Plane E-Plane Gain (dBd) Fixed Electrical Downtilt Options* Length x Width x Depth (in inches) LPA-4016 _ 806-941 MHz 40° 14° 16 dBd 1.25°, 5° 47.2” x 21.3” x 13.7” LPA-4019 _ 806-941 MHz 40° 7° 19 dBd 1.25°, 3°, 5° 94.5” x 21.3” x 13.7” LPA-80063/4CF _ 806-960 MHz 63° 15° 13 dBd 0°, 5° 47.4” x 15.2” x 13.2” LPA-80063/6CF _ 806-960 MHz 63° 10° 14.5 dBd 0°, 2°, 5° 70.9” x 15.0” x 13.1” LPA-80063/8CF _ 806-960 MHz 63° 7° 16 dBd 0°, 2°, 5° 94.5” x 15.2” x 13.2” LPA-80080/4CF _ 806-960 MHz 80° 15° 12.5 dBd 0°, 5° 47.2” x 5.5” x 13.2” LPA-80080/6CF _ 806-960 MHz 80° 10° 14 dBd 0°, 2°, 5° 70.9” x 5.5” x 13.2” LPA-80080/8CF _ 806-960 MHz 80° 7° 15 dBd 0°, 2°, 3°, 5° 94.5” x 5.5” x 13.2” LPA-80090/4CF _ 806-960 MHz 90° 15° 11.5 dBd 0°, 5° 47.2” x 5.5” x 9.4” LPA-80090/8CF _ 806-960 MHz 90° 7° 14.5 dBd 0°, 3°, 5° 94.5” x 5.5” x 9.4” LP A- 800 63 / 6 CF E-DIN 5° Electrical Downtilt Connector Type NE is an elongated N connector E-DIN is an elongated DIN connector CF refers to a “Center-Fed” connector Number of element sets Also refers to the approx. length in feet Horizontal Beamwidth Operating Frequency Range 800 = Operates within 806-960 MHz LPA-800 Series Our LPA (Log Periodic Antenna) 800 series is a group of log periodic dipole antennas operating within the 806-960 MHz frequency spectrum. These vertically polarized antennas feature the same true log periodic design as our classic LPD series, but are designed for more stringent zoning requirements with lighter weights and low profiles. The LPA design features more active elements than industry standard log periodic antennas. This dynamic, multiple array allows quick roll-off in the horizontal plane without impacting the half power points. The quick roll-off minimizes sector overlap, which con- tributes to the control of soft hand-off and pilot pollution. Design and Construction of the LPA-800 Log Periodic: LPAantennas are manufactured with our exclusive 3T Technology, featuring a true log periodic design that allows for excellent front- to-side characteristics to minimize sector overlap; a unique feedline design that eliminates the need for conventional solder joints in the signal path; a non-collinear system with access to each radiating element for control of the shaping of the vertical pattern; air as insulation for virtually no internal signal loss; fiberglass radomes and aircraft grade aluminum reflector plates for even heat dissipa- tion to minimize plate warping and bending. Model Number Guide: Amphenol Antel, Inc. Model’s Currently Available: *Some downtilt models may operate at a different frequency range than that listed. Please consult specification sheet for actual frequency range. When ordering replace “ __” with the connector type (NE or E-DIN). The LPA-4016 and LPA-4019 are exceptions to above example. Check specification sheet for more information.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Log Periodic Dipole Antennas806-960 MHz
Model Number Frequency Range(MHz) H-Plane E-Plane Gain
(dBd)Fixed Electrical
Downtilt Options*Length x Width x Depth
(in inches)
LPA-4016 _ 806-941 MHz 40° 14° 16 dBd 1.25°, 5° 47.2” x 21.3” x 13.7”
LPA-4019 _ 806-941 MHz 40° 7° 19 dBd 1.25°, 3°, 5° 94.5” x 21.3” x 13.7”
LPA-80063/4CF _ 806-960 MHz 63° 15° 13 dBd 0°, 5° 47.4” x 15.2” x 13.2”
LPA-80063/6CF _ 806-960 MHz 63° 10° 14.5 dBd 0°, 2°, 5° 70.9” x 15.0” x 13.1”
LPA-80063/8CF _ 806-960 MHz 63° 7° 16 dBd 0°, 2°, 5° 94.5” x 15.2” x 13.2”
LPA-80080/4CF _ 806-960 MHz 80° 15° 12.5 dBd 0°, 5° 47.2” x 5.5” x 13.2”
LPA-80080/6CF _ 806-960 MHz 80° 10° 14 dBd 0°, 2°, 5° 70.9” x 5.5” x 13.2”
LPA-80080/8CF _ 806-960 MHz 80° 7° 15 dBd 0°, 2°, 3°, 5° 94.5” x 5.5” x 13.2”
LPA-80090/4CF _ 806-960 MHz 90° 15° 11.5 dBd 0°, 5° 47.2” x 5.5” x 9.4”
LPA-80090/8CF _ 806-960 MHz 90° 7° 14.5 dBd 0°, 3°, 5° 94.5” x 5.5” x 9.4”
LPA- 800 63 / 6 CF E-DIN 5°
Electrical Downtilt
Connector TypeNE is an elongated N connectorE-DIN is an elongated DIN connector
CF refers to a “Center-Fed” connector
Number of element setsAlso refers to the approx. length in feet
Horizontal Beamwidth
Operating Frequency Range800 = Operates within 806-960 MHz
LPA-800 Series
Our LPA (Log Periodic Antenna) 800 series is a group of log periodic dipole antennas operating within the 806-960 MHz frequencyspectrum. These vertically polarized antennas feature the same true log periodic design as our classic LPD series, but are designedfor more stringent zoning requirements with lighter weights and low profiles.
The LPA design features more active elements than industry standard log periodic antennas. This dynamic, multiple array allowsquick roll-off in the horizontal plane without impacting the half power points. The quick roll-off minimizes sector overlap, which con-tributes to the control of soft hand-off and pilot pollution.
Design and Construction of the LPA-800 Log Periodic:LPA antennas are manufactured with our exclusive 3T Technology, featuring a true log periodic design that allows for excellent front-to-side characteristics to minimize sector overlap; a unique feedline design that eliminates the need for conventional solder joints inthe signal path; a non-collinear system with access to each radiating element for control of the shaping of the vertical pattern; air asinsulation for virtually no internal signal loss; fiberglass radomes and aircraft grade aluminum reflector plates for even heat dissipa-tion to minimize plate warping and bending.
Model Number Guide:
Amphenol Antel, Inc.
Model’s Currently Available:
*Some downtilt models may operate at a different frequency range than that listed. Please consult specification sheet for actual frequency range.When ordering replace “ __” with the connector type (NE or E-DIN).
The LPA-4016 and LPA-4019 are exceptions to above example. Check specification sheet for moreinformation.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertically Polarized, Log Periodic 40° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-4016 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.5) Worst case at 15° mechanical downtilt.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.35:1
Polarization Vertical1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 14°1) Electrical Downtilt 1.25°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.Aluminum reflector.
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.5) Worst case at 15° mechanical downtilt.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.35:1
Polarization Vertical1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 14°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.Aluminum reflector.
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.5) Worst case at 15° mechanical downtilt.
Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.35:1
Polarization Vertical1) Gain 19 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 7°1) Electrical Downtilt 1.25°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.5) Worst case at 15° mechanical downtilt.
Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-941 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.35:1
Polarization Vertical1) Gain 19 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 7°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.
Mechanical specifications
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.5) Worst case at 15° mechanical downtilt.
Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.35:1
Polarization Vertical1) Gain 19 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 40°
E-Plane 7°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Durable brass feedline design eliminatesthe need for conventional solder joints inthe signal path.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 665 N 149.5 lbsSide 577 N 129.6 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket and Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 15°1) Electrical Downtilt 0°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 63° / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80063/4CF __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 665 N 149.5 lbsSide 577 N 129.6 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket and Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 15°1) Electrical Downtilt 5°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 63° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80063/6CF __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 993 N 223.3 lbsSide 872 N 196.1 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 10°1) Electrical Downtilt 0°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 63° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80063/6CF __ 2°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 993 N 223.3 lbsSide 872 N 196.1 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 10°1) Electrical Downtilt 2°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 63° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80063/6CF __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 993 N 223.3 lbsSide 872 N 196.1 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 10°1) Electrical Downtilt 5°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 63° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80063/8CF __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1357 N 305 lbsSide 1197 N 269 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 7°1) Electrical Downtilt 0°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Antenna available with center-fedconnector only.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Vertically Polarized, Log Periodic 63° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80063/8CF __ 2°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1357 N 305 lbsSide 1197 N 269 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 7°1) Electrical Downtilt 2°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Antenna available with center-fedconnector only.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Vertically Polarized, Log Periodic 63° / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80063/8CF __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 1357 N 305 lbsSide 1197 N 269 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 63°
E-Plane 7°1) Electrical Downtilt 5°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Antenna available with center-fedconnector only.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Vertically Polarized, Log Periodic 80° / 12.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80080/4CF __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 254 N 57.1 lbsSide 574 N 129.0 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 12.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 15°1) Electrical Downtilt 0°1) Null Fill 15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 80° / 12.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80080/4CF __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 254 N 57.1 lbsSide 574 N 129.0 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 12.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 15°1) Electrical Downtilt 5°1) Null Fill 15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 80° / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80080/6CF __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 415 N 93.3 lbsSide 870 N 195.6 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 14 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 10°1) Electrical Downtilt 0°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 80° / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80080/6CF __ 2°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 415 N 93.3 lbsSide 870 N 195.6 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 14 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 10°1) Electrical Downtilt 2°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 80° / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80080/6CF __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 415 N 93.3 lbsSide 870 N 195.6 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in)
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 14 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 10°1) Electrical Downtilt 5°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 80° / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80080/8CF __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 580 N 130 lbsSide 1198 N 269 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 15 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 7°1) Electrical Downtilt 0°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 80° / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80080/8CF __ 2°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 580 N 130 lbsSide 1198 N 269 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 15 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 7°1) Electrical Downtilt 2°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 80° / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80080/8CF __ 3°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 580 N 130 lbsSide 1198 N 269 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 15 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 7°1) Electrical Downtilt 3°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 80° / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80080/8CF __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 580 N 130 lbsSide 1198 N 269 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 15 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 80°
E-Plane 7°1) Electrical Downtilt 5°1) Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 90° / 11.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80090/4CF __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 254 N 57.1 lbsSide 415 N 93.3 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 11.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 15°1) Electrical Downtilt 0°1) Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 90° / 11.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80090/4CF __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 254 N 57.1 lbsSide 415 N 93.3 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 11.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 15°1) Electrical Downtilt 5°1) Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 90° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80090/8CF __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 582 N 131.0 lbsSide 896 N 201.5 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 7°1) Electrical Downtilt 0°1) Null Fill 15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 90° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80090/8CF __ 3°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 582 N 131.0 lbsSide 896 N 201.5 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 7°1) Electrical Downtilt 3°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
Vertically Polarized, Log Periodic 90° / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPA-80090/8CF __ 5°
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper sidelobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
Wind Load @ 100 mph (161 km/hr)Fore/Aft 582 N 131.0 lbsSide 896 N 201.5 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-102 mm (2.0-4.0 in). If the lock-downbrace is used, the maximum diameter is Ø88.9mm (3.5 in).
Mounting Bracket & Downtilt Bracket Kit #21699999
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50Ω3) Connector(s) NE or E-DIN
1 port / center1) VSWR ≤ 1.4:1
Polarization Vertical1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle
H-Plane 90°
E-Plane 7°1) Electrical Downtilt 5°1) Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
True log-periodic design allows for superiorfront-to-side characteristics to minimizesector overlap.
Unique feedline design eliminates the needfor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internal signal loss.
Antenna available with center-fedconnector only.
1300 Capital Drive Rockford, IL 61109 Toll-Free (888) 417-9562 Tel. (815) 399-0001 Fax. (815) 399-0156 Email: [email protected] www.antelinc.com
Model Number Frequency Range(MHz) H-Plane E-Plane Gain
(dBd)Fixed Electrical
Downtilt Options**Length x Width x Depth
(in inches)
LPD-4013 _ 806-900 MHz* 40° 30° 13 dBd 1.25° 23.6” x 21.3” x 13.7”
LPD-4016 _ 806-941 MHz* 40° 14° 16 dBd 1.25°, 3°, 5°, 9° 47.2” x 21.3” x 13.7”
LPD-4019 _ 806-960 MHz 40° 7° 19 dBd 1.25°, 3°, 5° 94.5” x 21.3” x 13.7”
LPD-7908 _ 806-900 MHz* 60° 53° 8 dBd 0° 11.8” x 5.1” x 25.2”
LPD-7908/2 _ 806-900 MHz* 60° 26° 11 dBd 0° 23.6” x 5.1” x 25.2”
LPD-7908/4 _ 806-900 MHz* 60° 13° 14 dBd 1.25°, 3°, 5°, 9° 47.3” x 5.1” x 25.2”
LPD-6513 _ 806-941 MHz* 65° 15° 13 dBd 1.25°, 3°, 5°, 9° 47.2” x 13.9” x 11.2”
LPD Series
The LPD (Log Periodic Dipole) series is a group of log periodic antennas operating within the 806-900 MHz, 806-941 MHz, and 806-960 MHz frequency range. These antennas are an ideal choice for sectorized sites in which performance is the priority. LPD’s offera true log periodic design with more active elements than industry standard antennas. This dynamic, multiple array allows quick roll-off in the horizontal plane without impacting the half power points. The quick roll-off minimizes sector overlap, which contributes tothe control of soft hand-off and pilot pollution.
Design and Construction of the LPD Log Periodic:LPD antennas are manufactured. with our exclusive 3T Technology, featuring a true log periodic design that allows for excellent front-to-side characteristics to minimize sector overlap; a unique feedline design that eliminates the need for conventional solder joints inthe signal path; a non-collinear system with access to each radiating element for control of the shaping of the vertical pattern; air asinsulation for virtually no internal signal loss; fiberglass radomes and aircraft grade aluminum reflector plates for even heat dissipa-tion to minimize plate warping and bending.
Model Number Guide:
Amphenol Antel, Inc.
Model’s Currently Available:
LPD 790 8 / 4 E-DIN 3°
Electrical DowntiltConnector TypeNE is an elongated N connectorE-DIN is an elongated DIN connector
References Antenna Length in Feet
Horizontal Beamwidth: “8” = 60°,“7” = 80°, “5” = 92°Operating Frequency Range790 = Operates within 806-960 MHz
Exceptions: The following antenna models are exceptions to the examples shown above:LPD-4016, LPD-4019, LPD-6513, and LPD-6516LPD 65 13 E-DIN 5°
Electrical Downtilt
Connector TypeNE is an elongated N connectorE-DIN is an elongated DIN connector
Gain in dBd
Horizontal Beamwidth
This rule does not apply to the LPD-7905/4/102 and LPD-7905/8/102.
*This model is also available up to 960 MHz. Contact your sales representative for details.**Some downtilt models may operate at a different frequency range than that listed. Please consult specification sheet for actual frequency range.When ordering replace “__” with the connector type (NE or E-DIN).
Continued on next page ...
Model Number Frequency Range(MHz) H-Plane E-Plane Gain
(dBd)Fixed Electrical
Downtilt Options**Length x Width x Depth
(in inches)
LPD-6516 _ 806-960 MHz* 65° 7° 16 dBd 1.25°, 3°, 5° 94.5” x 13.9” x 11.2”
LPD-7907 _ 806-900 MHz* 80° 56° 7 dBd 0° 11.8” x 5.1” x 14.8”
LPD-7907/2 _ 806-900 MHz* 80° 28° 10 dBd 0° 23.6” x 5.1” x 14.8”
LPD-7907/4 _ 806-960 MHz 80° 14° 13 dBd 1.25°, 3°, 5°, 9° 47.2” x 5.1” x 14.8”
LPD-7907/8 _ 806-900 MHz* 80° 7° 16 dBd 1.25°, 3°, 5° 94.5” x 5.1” x 14.8”
LPD-7905 _ 806-941 MHz* 92° 60° 5 dBd 0° 11.8” x 5.1” x 9.6”
LPD-7905/2 _ 806-900 MHz* 92° 30° 8 dBd 0° 23.6” x 5.1” x 9.6”
LPD-7905/4 _ 806-941 MHz* 92° 15° 11.5 dBd 1.25°, 3°, 5°, 9° 47.2” x 5.1” x 9.6”
LPD-7905/8 _ 806-960 MHz 92° 7° 14.5 dBd 1.25°, 3°, 5° 94.5” x 5.1” x 9.6”
LPD-7905/4/102 _ 806-941 MHz* 102° 15° 10.5 dBd 1.25°, 3°, 5°, 9° 47.2” x 5.1” x 9.6”
LPD-7905/8/102 _ 806-941 MHz* 102° 7° 13.5 dBd 1.25°, 3°, 5° 94.5” x 5.1” x 9.6”
Amphenol Antel, Inc.
Model’s Currently Available:
LPD Series Continued
*This model is also available up to 960 MHz. Contact your sales representative for details.**Some downtilt models may operate at a different frequency range than that listed. Please consult specification sheet for actual frequency range.When ordering replace “__” with the connector type (NE or E-DIN).
Vertically Polarized, Log Periodic 40° / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
LPD-4013 __
Revision Date: 7/5/07
When ordering replace “___” with connector type.
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
50 60
70 80 90100110120
130
140
150
160
170
180
-170
-160
-150
-140
-130-120
-110 -100 -90 -80 -70-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.