Instructions-Parts Light Tower Kit Diagnostic indicator for use with single supply, tandem supply, and other GCA equipped systems. Important Safety Instructions Read all warnings and instructions in your supply system operation and repair manuals. Save all instructions. 1 2 3 1 2 (CMXXXX, GDXXXX) ti10920a ti10921b 3 D200s, D200, S20 2 3 r_255467_312493c Model 255467 For Single Supply Systems with DataTrak and D60 1 Model 255468 For Electric Crossover Tandem Supply Systems and Warm Melt Systems (TCXXXX, TDXXXX, TWXXX Ref. Description Qty . 1 LIGHT TOWER, Model 255467 1 2 SCREW, machine 3 NUT, hex Ref. Description Qty . 1 LIGHT TOWER, Model 255468 1 2 SCREW, machine 3 NUT, hex 312493G EN
4
Embed
Light Tower Kit · Feed the light tower cable through the hole in the light tower mounting bracket. 3. Attach light tower to bracket with screws (2) and hex nuts (3). 4. Plug connector
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Instructions-Parts
Light Tower KitDiagnostic indicator for use with single supply, tandem supply, and other GCA equipped systems.
Important Safety InstructionsRead all warnings and instructions in your supply system operation and repair manuals. Save all instructions.
1
2
3
1
2
(CMXXXX, GDXXXX)
ti10920a ti10921b
3
D200s, D200, S20
2
3r_255467_312493c
Model 255467 For Single Supply Systems with DataTrak
and D60
1
Model 255468 For Electric Crossover Tandem Supply Systems and Warm Melt Systems (TCXXXX, TDXXXX,
TWXXX
Ref. DescriptionQty
.1 LIGHT TOWER, Model 255467 12 SCREW, machine3 NUT, hex
Ref. DescriptionQty
.1 LIGHT TOWER, Model 255468 12 SCREW, machine3 NUT, hex
312493G EN
Installation
2 312493G
Installation
Mounting Provided (Rams)1. Loosen six captive screws (A) and disassemble
shrouds (B) from supply system.
2. Feed the light tower cable through the hole in the light tower mounting bracket.
3. Attach light tower to bracket with screws (2) and hex nuts (3).
4. Plug connector at end of light tower cable into corre-sponding green connector on the DataTrak or dis-play module harness.
For tandem systems, plug light tower connector into fluid control module connector number 2. See your supply system manual for electrical connection schematic.
5. Reattach the shrouds (B).
Mounting Not Provided1. Locate the light tower so it is visually unobscured.
2. Drill the hole pattern for the light tower.
NOTE: A 1:1 drill template has been provided on this page.
FIG. 1: Shroud Removal
FIG. 2: Hole Pattern
A
B
B
r_289105_312375a
Feed cablethrough
MountingHoles
ti10922a
FIG. 3: Electrical Connection
FIG. 4: Hole Pattern
From DataTrak/Display
2
3
ti10920a
0.85 in.0.70 in.
0.80 in. (20 mm)Diameter
(22 mm)
(18 mm)
0.26 in. (7 mm)
4x 10-32 UNCEqually Spaced2.10 in. (53 mm)Bolt Circle
3x 0.20 in. (5 mm)Equally Spaced1.57 in. (40 mm)Bolt Circle
Diameter
Accessories
312493G 3
3. Feed the light tower cable through the hole of the light tower mounting pattern. See FIG. 2.
4. Attach the light tower to the hole pattern with the screws and hex nuts provided.
5. Plug the connector at the end of the light tower cable into port 1 found on the Advanced Display Module (ADM).
Accessories
Light Tower Extension Cables
TroubleshootingLight Tower Signals
NOTE: See supply systems manual for details of the specific errors associated with the light tower sig-nals.
E-Flo iQ Dispense System Troubleshooting
See the E-Flo iQ Dispense System Operation manual no. 333587 for more information.
E-Flo iQ Light Tower Signals
Drill TemplateNOTE: Drill Template is 1:1 Scale.
FIG. 5: Advanced Display Module
Part No. Length (meter)
122487 1.5
121728 4.0
124003 5.0
121005 15
121006 50
Signal Description
Green on only(Only model 255468)
System is powered up and there are no error conditions present.
Yellow flashing A low priority error exists.
Yellow on A medium priority error exists.
Red flashing A high priority error exists.
Red on The system is shut down due to error conditions.
Signal Description
Off System is not active.
Green on onlySystem is active and there are no error conditions present.
Green blinking Heat is warming up.
Yellow on An advisory exists.
Yellow blinking A deviation exists.
Red solidThe system is shut down due to an alarm occurring.
All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice.
For patent information, see www.graco.com/patents.
Original instructions. This manual contains English. MM 312493
Graco Headquarters: MinneapolisInternational Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2007, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.www.graco.com