Lanier LP116c Color Printer Training. Terminology 1. Main Output Tray 2. Toner Cartridge Cover 3. Control Panel & Display Screen 4. Front Cover 5. Manual.

Lanier LP116cColor Printer Training

Terminology

1. Main Output Tray

2. Toner Cartridge Cover

3. Control Panel &Display Screen

4. Front Cover

5. Manual Feed Tray

6. Paper Tray 1

More Terminology

1. Side Cover

2. Power Switch

Rear/Back View

Right Side View }

The Guts

1. Fuser2. Transfer Roller3. Toner Cartridges4. Printer Cartridges

(Black & Color)5. Waste Toner Cartridge

Changing Toner

3. Place cartridge in appropriate color slot

4. Slowly push the cartridge toward the back until it locks into place

Replacing a Toner Cartridge1. Pull the handle toward the

front of the printer2. Lift the cartridge straight

up

Removing a Toner Cartridge

*Replace only when Display Screen says “Add COLOR”

Print Cartridges

1. Unlatch the two green tabs across from each other

2. Lift up on the black bar

3. Press the green tab to the cartridge desired and pull it out

1.2.

3.

Removing the Print Cartridges

Print Cartridges

1. Make sure the green arrow fits securely on the track before pushing the cartridge in

2. When the cartridge is slid into place, close the lock bar and snap the two green tabs on to secure it

1.2.

Replacing the Print Cartridges

*Replace only when the Display Screen says “Replace PCU”

Waste Toner

1. Unlock the waste toner

2. Pull the waste toner straight out

3. Insert a new waste toner

4. Lock the new waste toner

1.

2.

3.

4.

*Replace only when the Display Screen says “Replace Waste Toner”

Paper Trays

1. Open the Manual Feed (Bypass Tray) and fully extend the tray

2. Insert the paper and adjust the guides so they are snuggly against the paper

*Note the side that will be printed on is the face down side

1.

2.

Loading the Manual Feed Tray

Paper Trays

• Press Menu and go to Paper Input and press “Enter#”

• Go to Bypass Size and press “Enter#”

• Choose paper size and press “Enter#”

Change the paper size for the Bypass Tray

*Note that the paper cannot exceed a width of 8.5 inches

Paper Trays

1. Pull on the handle at the absolute bottom of the front

2. Remove the tray form the printer by lifting up as it is being pulled out

3. Open the width of the tray up all the way by holding the guides on the sides of the tray and moving them outward

4. Slide paper in from the back of the tray and tighten the paper guides snuggly against the paper

5. Return the tray to the bottom of the printer

Loading paper in Tray 1 (Default Tray)

1. - 2.

3.

4.

Jams? Where?

• Remove Misfeed A: Internal Path

• Remove Misfeed B: Fuser Unit

• Remove Misfeed Y: Paper Tray

When the printer is jammed it will display one of the following:

Jam: Internal Path Fix

1. Open the front cover

2. Locate the jam under the Fuser Unit (Caution: HOT!)

3. Slowly pull the jam out

4. If the jam does not come out easily, look at the lower right side and locate the letter A on the wall of the printer

5. Pull it down and remove the jam

1.

2. – 3.

5.

4.

Jam: Fuser Unit Fix1. Open the front cover

2. Lift the left and right “B1” blue levers on the fuser

3. Remove Jam

1.

2.3.

4. If the jam does not come out easily, pull “B2” down.

5. Remove Jam

4.

5.

CAUTION: Fuser is HOT!

Jam: Paper Tray Fix

1. Slowly pull the paper tray out

2. Remove Jam

3. Open the front cover and then close the front cover to reset the jam condition

1.2.

3.