K1 K2 K3 K4 K5 K6 K7 K8 K9 K10 K11 K12 K13 K14 K15 K16 K17 K18 K19 K20 K21 K22 K23 K24 K25 K26 K27 K28 K29 K30 K31 K32 K33 K34 K35 K36 K37 K38 K39 K40 K41 K42 K43 K44 K45 K46 K47 K48 K49 K50 K51 K52 K53 K54 K55 K56 K57 K58 K59 K60 K900 Universal junction pit End/outlet cap K01 K010 K0102 K020 K0202 K030 K0302 K040 K050 K060 www.acoaus.com.au 28 29 KlassikDrain - K100/KS100 K900 in-line pit In-line pit providing DN100 pipe connection through cast-in rubber ‘O’ ring, when plastic insert is removed. Available with plastic rubbish basket. Any channel can be connected into the in-line pit by removing a section of the end wall to the correct height. Drill-outs guide this connection to channel K5, K10, K15, K20, K25 and K30. Not recommended for channel nos. K31-K60. End/100mm inlet/outlet cap Fits all channels. Manufactured from grey ABS to complement edge rail. Guides aid cutting to correct height. Socket connection to DN100 pipes. Seal pipe to end cap using PVC-ABS cement. Note: For channels K1-K10, ACO recommends removal of socket to ensure adequate pavement material coverage. For channels K31-K60, two end caps are required. Cut second end cap, discard socket and glue to first end cap to the required height. Series 600, Universal Junction Pit Universal pit with drill-outs for DN150 or DN225 pipe connection. Supplied complete with grate. Available with plastic rubbish basket. Any channel can be connected into the pit by removing a section of the end wall to the correct height. See page 56 for details. One metre channels 0.6% sloped channels in metre lengths and 60 depths which connect to create 60 metre continuous sloped run. Neutral channels available in seven depths. Can be assembled to produce constant depth runs, or inserted in sloped runs to increase their length. System layout Half metre channels Neutral channels in three constant depths to supplement one metre channels. K31-K60 channels To create up to a 60 metre continuous sloped run, an extension piece is attached to the top of the channel. Each channel comes complete with integrally bonded extension piece.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
K1K2
K3K4
K5K6
K7K8
K9K10
K11K12
K13K14
K15K16
K17K18
K19K20
K21K22
K23K24
K25K26
K27K28
K29K30
K31K32
K33K34
K35K36
K37K38
K39K40
K41K42
K43K44
K45K46
K47K48
K49K50
K51K52
K53K54
K55K56
K57K58
K59K60
K900 Universal junction pit
End/outlet cap
K01
K010K0102
K020K0202
K030K0302
K040
K050
K060
www.acoaus.com.au
28 29
KlassikDrain - K100/KS100
K900 in-line pitIn-line pit providing DN100 pipe connection through cast-inrubber ‘O’ ring, when plastic insert is removed. Available withplastic rubbish basket.
Any channel can be connected into the in-line pit by removinga section of the end wall to the correct height. Drill-outsguide this connection to channel K5, K10, K15, K20, K25and K30. Not recommended for channel nos. K31-K60.
End/100mm inlet/outlet capFits all channels. Manufactured from greyABS to complement edge rail. Guides aidcutting to correct height. Socketconnection to DN100 pipes. Seal pipe toend cap using PVC-ABS cement.
Note: For channels K1-K10,ACO recommends removal ofsocket to ensure adequatepavement material coverage.
For channels K31-K60, two endcaps are required. Cut secondend cap, discard socket andglue to first end cap to therequired height.
Series 600, Universal Junction PitUniversal pit with drill-outs for DN150 orDN225 pipe connection. Suppliedcomplete with grate. Available with plasticrubbish basket.
Any channel can be connected into the pitby removing a section of the end wall tothe correct height. See page 56 for details.
One metre channels0.6% sloped channels in metre lengthsand 60 depths which connect to create 60 metre continuous sloped run.
Neutral channels available in seven depths. Can be assembled to
produce constant depth runs, orinserted in sloped runs to
increase their length.
System layout
Half metre channelsNeutral channels in three constant depthsto supplement one metre channels.
K31-K60 channelsTo create up to a 60 metrecontinuous sloped run, anextension piece is attachedto the top of the channel.Each channel comescomplete with integrallybonded extension piece.
Notes:1. Preformed drillout for DN100 or DN150 pipe on underside of every channel2. End cap can be cut down to suit all channels, K31-K60, two end caps required3. See pages 34-37 for grate details4. See pages 56-57 for details on universal junction pit5. To calculate overall depth add 25mm to invert depth
K100 Parts list
500mm
191mm,251mm,311mm
Half metre channel
311m
m137m
m
251m
m
191m
m
585m
m371m
m
491m
m
431m
m
877m
m
Ground line
Maximum permissible outlet (flow through) rates
1. These are approximate unrestricted flow rates (rubbish baskets are excluded)2. These are not channel capacities, contact ACO for channel hydraulics advice
K100 Accessories
1000mm
317mmto
497mm
153mm
130mm
100mm
One metre channel - K31 to K60
Universal junction pit
Channel accessories
K100 Channel with galvanised rail K100 Channel with galvanised rail
601 pit with Slotted DI grate - (0.5m) 98009 849 849 98.1602 pit with Intercept DI grate - (0.5m) 98015 849 849 100.9Series 600 plastic rubbish basket 98653 - - 1.3
End/DN100 inlet/outlet cap 90509 - - 0.2QuickLok locking bar 02899 - - 0.1QuickLok grate removal tool 01318 - - 0.1150mm oval to round adaptor 00821 - - 0.5
In-line drainage pit Notes:1. Preformed drillout for DN100 or DN150 pipe on underside of every channel2. End cap can be cut down to suit all channels, KS31-KS60, two end caps required3. See pages 34-37 for grate details4. See pages 56-57 for details on universal junction pit5. To calculate overall depth add 25mm to invert depth
KlassikDrain - KS100
32 33
www.acoaus.com.au
KS100, a version of the KlassikDrainK100 system where the integrally cast-inedge rail is manufactured from grade 304stainless steel instead of galvanised steel.
KS100 is used for high profileapplications requiring enhancedaesthetics, or where increased corrosionresistance is required.
ACO does not recommend the use ofgalvanised steel grates with KS100 asthis may cause galvanic corrosion.
See pages 34 to 37 for grate details.
KS100 Parts list
KS100 Accessories
Universal Junction pit
Channel accessories
www.acoaus.com.au
KS100 Channel with stainless rail KS100 Channel with stainless rail
601 pit with Slotted DI grate - (0.5m) 98009 849 849 98.1602 pit with Intercept DI grate - (0.5m) 98015 849 849 100.9Series 600 plastic rubbish basket 98653 - - 1.3
End/DN100 inlet/outlet cap 90509 - - 0.2QuickLok locking bar 02899 - - 0.1QuickLok grate removal tool 01318 - - 0.1150mm oval to round adaptor 00821 - - 0.5
QuickLok
34 35
www.acoaus.com.auwww.acoaus.com.au
1 Grade 304 stainless steel - 5mm Vee bar with anti-slip nodules (Patent no. 635425)
QuickLok - boltless locking system
Comprised of a glass nylon stud, factory fitted to the grate, which allows a snap fit intothe stainless steel spring clip in the locking bar. With no loose bolts or bars, QuickLokprovides secure boltless locking, that is easy to remove/replace for maintenance andcleaning. Saves time and money during installation.
K100
To remove bar, insert
screwdriver into hole
at end of bar and
lever back serrated
end, rotate bar free.
K200/K300
Push plastic clips
back to unlock, rotate
bar free.
Push down or stand
on grate until it snaps
into place.
K100
Use a hammer to tap
bar into position, so
that serrated ends
grip in recess.
K200/K300
Push plastic clips
forward to lock bar
into position.
Locate locking bar in
wall recesses by
rotating clockwise.
To remove grate,
insert locking tool
hook between slots
and pull grate
upwards, to snap
free. Remainder of
grates can be pulled
out by hand - gloves
are recommended.
To install grate, align
QuickLok pin directly
over locking bar.
1 Polypropylene
1Grade 304 stainless steel - 3mm Vee bar
1 Grade 304 stainless steel
1 Grade 304 stainless steel
11 22 33 44 55 66
1 Grade 304 stainless steel
Description Part Length Weight Slot size Intake LockingNo. mm kg mm area mm2 type