Exploring the effects of seed size and target plant densities on the yield of hybrid canola across Australia Justin Kudnig, Pacific Seeds Key words: canola, varieties, hybrid, triazine tolerant (TT), Roundup Ready (RR), Clearfield + triazine tolerant (CT), cultivar type, seed size, plant populations, seed-lots, plant height, grain yield. Key messages Genetics x Environment x Management interactions are very complex and dynamic. Genetics (G) is the most controllable factor, more specifically for pre-planting, i.e. varietal choice, while Environment (E) is by far the most significant factor. Management (M) will influence yield to a small degree in some environments, but for every environment where M has a significant effect, there are many environments where it will not. From a crop management perspective, the main consideration is time spent, logistics and associated costs versus return. There was a trend for the RR hybrid with smaller seed size to generate population densities lower than targeted. There was a similar but less consistent trend for the TT and CT technologies with smaller seed size to generate lower population densities. However, we did not observe a statistically significant effect of seed size on plant count and the percentage of plants established relative to populations targeted varied substantially across different seed lots and environments. All four hybrid-seed lots with larger seed sizes generated more observed biomass at the 4-6 leaf stage. All hybrids with higher target treatments for plant population finished flowering and pod maturity two to four days earlier and plant height was observed as slightly lower, however this was not significant. This may provide benefits in terms of enhancing crop competitiveness against weeds in addition to reducing risk of high temperatures and/or frosting during flowering and early seed-fill stages. Despite a large range in seed size the grain yield (t/ha) of hybrids was not significantly different across environments or plant population treatments. However, there was a few individual environments where significant differences in grain yield (t/ha) were observed between hybrids with seed ranging from 4.54 to 8.92 grams per 1,000 seeds (equivalent to seed counts of 112,000 to 220,000 seeds per kilogram) within different plant population treatments. Aims To determine differences in plant establishment (plants/m 2 ), visual (subjective) plant vigour or biomass, windrowing maturity, plant height (cm) and grain yield (t/ha) production of four different hybrids across 11 different canola growing environments in Australia. The 11 trial environments differed widely in seasonal rainfall, cropping history, soil type, soil pH, water holding capacity. Best management practices and district standard practice treatments were applied per each location.
10
Embed
Key words: canola, varieties, hybrid, triazine tolerant (TT ... · Web viewThis paper outlines the results of canola seed-lot trials carried out in 2019 across a more diverse range
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Exploring the effects of seed size and target plant densities on the yield of hybrid canola across AustraliaJustin Kudnig, Pacific Seeds
Genetics x Environment x Management interactions are very complex and dynamic. Genetics (G) is the most controllable factor, more specifically for pre-planting, i.e. varietal choice, while Environment (E) is by far the most significant factor. Management (M) will influence yield to a small degree in some environments, but for every environment where M has a significant effect, there are many environments where it will not. From a crop management perspective, the main consideration is time spent, logistics and associated costs versus return.
There was a trend for the RR hybrid with smaller seed size to generate population densities lower than targeted. There was a similar but less consistent trend for the TT and CT technologies with smaller seed size to generate lower population densities. However, we did not observe a statistically significant effect of seed size on plant count and the percentage of plants established relative to populations targeted varied substantially across different seed lots and environments.
All four hybrid-seed lots with larger seed sizes generated more observed biomass at the 4-6 leaf stage. All hybrids with higher target treatments for plant population finished flowering and pod maturity two to four days earlier and plant height was observed as slightly lower, however this was not significant. This may provide benefits in terms of enhancing crop competitiveness against weeds in addition to reducing risk of high temperatures and/or frosting during flowering and early seed-fill stages.
Despite a large range in seed size the grain yield (t/ha) of hybrids was not significantly different across environments or plant population treatments. However, there was a few individual environments where significant differences in grain yield (t/ha) were observed between hybrids with seed ranging from 4.54 to 8.92 grams per 1,000 seeds (equivalent to seed counts of 112,000 to 220,000 seeds per kilogram) within different plant population treatments.
Aims
To determine differences in plant establishment (plants/m2), visual (subjective) plant vigour or biomass, windrowing maturity, plant height (cm) and grain yield (t/ha) production of four different hybrids across 11 different canola growing environments in Australia.
The 11 trial environments differed widely in seasonal rainfall, cropping history, soil type, soil pH, water holding capacity. Best management practices and district standard practice treatments were applied per each location.
Introduction
Previous research is conflicted regarding the impact of canola seed size, especially in hybrids, on percentage establishment, especially from depth.
Brill et al (2015) demonstrated that deep-sown hybrid cultivars with larger seed maintained higher emergence rates and grain yield than open-pollinated cultivars. They also showed that larger seed size of both hybrid and open-pollinated canola increased early biomass accumulation and final grain yield.
However, Harries & Seymour (2018) found that seed size did not significantly affect canola emergence, yield or seed quality. While an increasing seed size had a positive linear association with early canola biomass and 1000-seed weight, both days-to-flowering and days to the end of flowering had a negative linear association with seed size.
French et al (2016) carried out 24 experiments across a range of agricultural environments in Western Australia between 2010 and 2014 canola (Brassica napus L.). They found the response of grain yield to crop density could be adequately described by an asymptotic model (where yield approaches but never quite reaches a ceiling at very high density).
Zhang et al (2016) demonstrated that the relative yield and profit of Australian canola hybrids compared to open-pollinated canola was largely determined by growing-season rainfall.
This paper outlines the results of canola seed-lot trials carried out in 2019 across a more diverse range of Australian environments than previous studies. The aim was to determine the relative importance of canola seed size on plant population density and seed yield using various hybrids containing different genetic backgrounds and herbicide technologies.
Method
Eleven field research extension trials using randomised complete block design with three replicates were sown across Australia with the individual locations at Kellerberrin WA, York WA, Gnowangerup WA, Wagin WA, Kojonup WA, Nyabing WA, Beulah Vic, Lake Bolac Vic, Greenethorpe NSW, Ardlethan NSW and Lockhart NSW.
Four canola varieties of differing maturity within three different herbicide technology groups and with three different target populations were compared. Herbicide technologies included: CT - Clearfield® + Triazine Tolerant, Triazine Tolerant and Roundup Ready®. Varieties included: a 3-series early TT Hybrid, a 4-series early-mid RR Hybrid, a 5- series mid-early TT Hybrid and a 5-series mid CT hybrid.
Target population treatments included: 15 plants per m2, 25 plants per m2 and 40 plants per m2 based on an estimated 65% establishment survival factorial by adjusting all seed packet weights.
Table 1. Details of the 2019 plant population by seed size hybrid trialsTrial Trial Trial Design Sowing GSR (mm) Trial Mean
Location State Purpose # Reps Date Rainfall Yield (t/ha)
York WA RR – Pop*Size RCB 3 21.05.2019 304 2.02
Kojonup WA RR – Pop*Size RCB 3 14.05.2019 280 1.17
Measurements done were plants per m2 using 4x1m row counts per plot 14 days after sowing and 28 days after sowing, visual subjective vigour ratings at the 4-6 leaf stage, visual maturity ratings at flowering and maturity, plant height in (cm) at 5cm intervals, grain yield (t/ha) using plot harvesters and oil % content using nuclear magnetic resonance spectroscopy.
Results and Discussion
French et al (2016) showed that field establishment varied from 0.3 to 1 (where 0.3 = 30% and 1 = 100%) and was higher at low target densities with a median of 0.585 at a target density of 40 plants/m². Our research showed whilst specifically referencing two hybrids, that final field establishment varied from 30% to 118% for Hyola 404RR and 23% to 133% for Hyola 559TT (Figures 1 and 2). Where the final establishment values were higher than 100% are most likely to have been a function of the pre-plant field establishment factorial used of 65%. Example calculation for the treatment Hyola 404RR-213 with Target = 15 plants/m2, Germination = 94%, Est Factorial = 65% and seeds sown = 25 per m2, [(25*0.94)*0.65)] = 15 plants per m2 where the maximum possible establishment from this seedlot is actually [(25*0.95)*1.0)] = 24 plants per m2 (156% of target).
0
20
40
60
80
100
120
67
93
107
93
52
96100
96
60
80
113
85
53
8793 93
56
88
104
84
55
80
100
78
47
93
113
80
52
76
100
84
40
65
108
68
40
9387
73
52
80
104
80
30
65
118
58
Hyola® 404RR - Mean % of target population achieved by treatment across four environments
Figure 1. Hyola 404RR: mean proportion (%) of target population achieved by seed size treatment across four environments.
0
20
40
60
80
100
120
140133
100
7380
113
80
107
80
104
80
48
112
72
100
65
98
73
30
88
50
105100
107
73
87
127
67
107
76
104
80
48
108
60
92
40
88
78
40
85
55
10093
107
7367
127
53
107
72
96
68
40
112
52
96
50
100
78
23
80
48
115
Hyola® 559TT - Mean % of Target Population Achieved by Treatment across 7 Environments
Figure 2. Hyola 559TT: mean proportion (%) of target population achieved by seed size treatment across four environments.
French et al (2016) demonstrated that there was little difference between optimum densities for hybrid and open-pollinated cultivars, with the optimal density in the high rainfall zone about 10 plants/m² higher than in low and medium rainfall zones.
Our research demonstrates that site environmental conditions, variety and seed-lot source had larger effects on final established % of plant numbers than seed size and target plant populations. Specifically related to seed-lot source, we anticipate that not every seedlot of any 'particular variety' with the same seed size/count may potentially have the same seed vigour or establishment growth behaviour.
Table 4. Hyola 404RR: treatment mean plant maturity (series) and plant height (cm)
Treatment Description Mean Plant Maturity Series Mean Plant Height (cm)
Table 4 shows that with Hyola 404RR, across all environments, there was a decrease in plant maturity within each seed size and when moving from lower to higher populations, however this was not always significant within individual environments. In most environments there was a decrease in mean plant height (2-4cm) with higher populations with only small differences in plant height when comparing between seed sizes (which were not significant).
Table 5. Hyola 350TT, Hyola 559TT and Hyola 580CT: treatment mean plant maturity (series) and plant height (cm).
Treatment Description Mean Plant Maturity Series Mean Plant Height (cm)
Table 5 shows with Hyola 350TT, Hyola 559TT and Hyola 580CT there was no consistent relationship between plant maturity and seed size or population density across environments.
In most environments there was a small decrease in mean plant height (3-6cm) with higher population treatments and only small differences in plant height when between seed size treatments (which were found not to be significant).
Yield responses across the 11 trial environments varied between varieties, seed sizes and plant population targets. Previous research studies have also shown mixed outcomes relating to the effect of seed size and plant densities on grain yield.
Catalier (2019) found in some studies, canola yield increased with seeding rate (Harker et al 2012a), while in other studies seeding rate did not influence yield (Kutcher et al 2013).
Gan et al (2016) observed that yield response to seeding rate appeared to depend not only on environment, but also on what seeding rates or plant densities were being compared.
Yang et al (2014) found that seed yield increased with seeding rate, however leveled off at higher plant densities. In regards to seed size, yield benefit from larger canola seed was observed by Elliot et al (2008) and Brill et al (2016), while Harker et al (2015), Clayton et al (2009), and Lamb and Johnson (2004) did not measure a benefit of larger seed on canola yield.
Table 6. Hyola 404RR: grain yield (t/ha) responses to four seed sizes and three target plant populations across four environments in Australia
Location Greenethorpe NSW Kojonup
WA Lake Bolac VIC York
WA
Treatment Yield t/ha sig Yield t/ha sig Yield t/ha sig Yield t/ha sig
Hyola 404RR-154-15 0.57 ab 1.10 ab 2.25 b 2.08 a
Hyola 404RR-154-25 0.62 a 1.15 ab 2.75 a 2.05 a
Hyola 404RR-154-40 0.63 a 1.35 a 2.46 ab 2.10 a
Hyola 404RR-181-15 0.58 ab 1.19 ab 2.14 b 1.88 a
Hyola 404RR-181-25 0.60 ab 1.25 ab 2.37 b 2.20 a
Hyola 404RR-181-40 0.63 a 1.24 ab 2.28 b 2.20 a
Hyola 404RR-196-15 0.50 b 0.97 b 2.35 b 1.91 a
Hyola 404RR-196-25 0.54 ab 1.21 ab 2.29 b 1.99 a
Hyola 404RR-196-40 0.59 ab 1.18 ab 2.49 ab 1.97 a
Hyola 404RR-213-15 0.57 ab 1.13 ab 2.43 ab 1.90 a
Hyola 404RR-213-25 0.61 a 1.24 ab 2.45 ab 2.06 a
Hyola 404RR-213-40 0.59 ab 0.99 b 2.30 b 1.87 a
Raw Mean 0.59 1.17 2.38 2.02 CV 11.05 15.98 9.16 10.67
LSD (P=0.05) 0.11 0.31 0.35 0.36
Gnowangerup WA Kellerberrin WA Nyabing WA Wagin WA0.00
0.25
0.50
0.75
1.00
1.25
1.50
1.75
2.00
2.252019 Hyola 350TT - Analysed Grain Yield (t/ha) by WA Location by Seed Size by Target Population
Figure 5. Hyola 580CT: grain yield (t/ha) responses to four seed sizes and three target plant populations across four Western Australian environments.
This paper has only shown the yield results from Western Australian trials for the CT and TT hybrids, however the Eastern Australian States trials showed similar relationships. Often there is little or no significant yield responses in RR, TT or CT hybrids with different seed sizes and plant population targets across all the testing environments.
As highlighted with all the 2019 individual trial results, hybrid genetic background and associated adaptability along with strong environmental influences (rainfall frequency and amounts, soil type, frost events, time of sowing) played a more substantial role or influence on the final yield responses than did seed size or actual plant population.
Conclusion
This study highlights that a canola ‘seed size range’ that optimises canola emergence and grain yield potentially exists (TSW 6.5g to 5.0g ≈ 150,000 to 190,000 seeds/kg) and that larger seed has been found to provide higher observed biomass accumulation and % establishment in some environments. However, G X E interactions often override (M) management decisions based around seed size, population targets and their resultant grain yields.
Seed size does impact the percentage of plants both emerged and established to varying levels in different environments, and larger seed at lower plant populations leads to final plant maturity being delayed. Higher plant populations irrespective of seed size and variety genetics often showed decreased observed maturity and sometimes plant height.
In 2020, Pacific Seeds will continue this important industry research by focusing the evaluation on the relationships between TT and CT hybrids vs 3 OP TT varieties (actual farmer prepared retained samples) at different plant populations and seed sizes. This research will help growers and advisors have more information around determining any potential grain yield and gross return $/ha value of grading OP TT varieties to larger seed sizes and planting at higher rates versus high yielding TT and CT hybrids.
Acknowledgments2019 Trial Development, design and analysis by Dr David Tabah, Crop Research Lead (Canola), Advanta Seeds
2019 Trial planting, maintenance, spraying and harvest across Australia by Kalyx Australia, Living Farms and TrialCo
ReferencesBrill R., Jenkins M. L., Gardner M. J., Lilley J. M., Orchard B. A. (2016) Optimising canola establishment and yield in south-eastern Australia with hybrids and large seed. Crop and Pasture Science 67, 409-418.
Brill RD, Jenkins L, Gardner M (2014) Canola establishment; does size matter? In ‘Grains Research and Development Corporation Advisor Update.
Catellier C, (2019) M.Sc. P.Ag., Research Associate Optimal Seeding rate based on seed size in canola. Project #Carp SCDC 20 18-084, The Saskatchewan Canola Development Commission.
French RJ, Seymour M, Malik RS (2016) Plant density response and optimum crop densities for canola (Brassica napus L.) in Western Australia. Crop & Pasture Science 67, 397–408.
Gan Yantai, a K. Neil Harker, b H. Randy Kutcher, c Robert H. Gulden, d Byron Irvine, e William E. May, f John T. O'Donovanb, (2016) Canola seed yield and phenological responses to plant density, Canadian Journal of Plant Science 96(1): 151-159
Hanson BK, Johnson BL, Henson RA, Riverland NR (2008) Seeding rate, seeding depth, and cultivar influence on spring canola performance in the Northern Great Plains. Agronomy Journal 100, 1339–1346.
Harker KN, O’Donovan JT, Smith EG, Johnson EN, Peng G, Willenborg CJ, Gulden RH, Mohr R, Gill KS, Grenkow LA (2015) Seed size and seeding rate effects on canola emergence, development, yield and seed weight. Canadian Journal of Plant Science 95, 1–8.
Kutcher HR,1 T. K. Turkington,2 G. W. Clayton,3 K. N. Harker2 (2013) Response of herbicide-tolerant canola (Brassica napus L.) cultivars to four row spacings and three seeding rates in a no-till production system. Canadian Journal of Plant Science, 2013, 93(6): 1229-1236
Zhang H, Berger JD, Milroy SP (2013) Genotype × environment interaction studies highlight the role of phenology in specific adaptation of canola (Brassica napus) to contrasting Mediterranean climates. Field Crops Research 144, 77–88.
Zhang H, Berger JD, Seymour M, Brill R, Herrmann C, Quinlan R, Knell G (2016) Relative yield and profit of Australian hybrid compared with open-pollinated canola is largely determined by growing-season rainfall. Crop & Pasture Science 67, 323–331.
Paper reviewed by
Dr David Tabah, Crop Research Lead (Canola) – Advanta Seeds Australia