TABLE OF CONTENTS Page ............................ Model SPC 100 4001026 ........................ Model SPC 140 4001027 ........................ Model SPC 140 with Ergo Handle 4001038 ........ Model SPC 141 4001041 ........................ Model SPC 142 4001040 ........................ Model SPC 165 4001028 ........................ Model SPC 165 with Ergo Handle 4001039 ........ Model SPC 165B (Brisket) 4001036 ............... Model SPC 165B (Brisket /Side Handle) 4001056 Model SPC 165G (Spinal Cord) 13mm 4001061 .... Model SPC 165G (Spinal Cord) 16mm 4001064 .... Model SPC 165GT (Spinal Cord Tails) 4001077 .... Model SPC 165J (Jowl) 4001043 ................. Air Hose 3059018 .............................. Balancer 4042033 ............................. Air Filter/Regulator/Lubricator 3022003 ............ Complete Assembly Tool Kit 8039162 ............. PRODUCTS CORPORATION 33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926 UNITED STATES OF AMERICA E--MAil [email protected]TEL. 860--347--7271 FAX. 860--347--6978 WWW.jarvisproducts.com Model SPC 100, 140, 141, 142, 165, 165B, 165G, 165GT, 165J Air Circular Saws EQUIPMENT SELECTION Ordering No. .............. • Notice to Employer and Safety Director 2 ........................... • Notice to Operators, Maintenance and Cleanup Personnel 3 .............. • Parts Diagram and List 4 .............. • Special Tools 11 ...................... • Specifications 12 ..................... • Installation Instructions 12 ............. • Operation Instructions 12 .............. • Maintenance Instructions 12 ........... ® JARVIS 6201008;:. SPC 165 SPC 100 SPC 165G SPC 165GT SPC 165B US Patents: 6,805,696 and 6,511,483 SPC 165 ERGONOMIC SPC 165J
16
Embed
JARVIS - coagro.ru · JARVIS® 6201008;:. PRODUCTS CORPORATION 33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926 UNITED STATES OF AMERICA E--MAil [email protected]
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
1. Remove and repair any tool that malfunctions. All personnel must be instructed to remove anymalfunctioning equipment.
2. Ensure that all employees who use this tool are trained in the proper use of this tool and are awareof the dangers that may arise if they do not follow the procedures outlined in this brochure.
3. Enclosed are four (4) copies of “NOTICE TO OPERATORS, MAINTENANCE AND CLEANUPPERSONNEL.” Post one copy on the employees’ bulletin board; give one copy to operator(s); giveone copy to themaintenance foreman; andgive one copy to the sub-contract cleanup / internal cleanupforeman. Additional copies will be provided upon request.
4. The tool is designed and intended to be powerful. This fact should be obvious to your employees,but you must emphasize it to them.
5. Never make modifications or alterations to the tool. Replace any missing or illegible labels.6. Ensure that proper procedures are established in accordancewithOSHA’s lockout/tagout procedures
(29 CFR 1910.147) to prevent accidental startup or release of stored energy.7. Hand/Wrist/Arm injury and other Cumulative Trauma Disorders may result from repetitive work,
motion or vibration. You must make your employees aware of hazards, symptoms of injury and ap-propriate prevention. See OSHA’s “Ergonomics ProgramManagement Guidelines for MeatpackingPlants.”
8. Follow our installation and maintenance instructions for proper installation and care of the tool.9. Ensure that employees wear eye protection in accordance with OSHA’s eye and face protection re-
quirements (29 CFR 1910.133) while operating the tool.10. Avoid injury. Do not permit the tool to be misused.11. Ifyou resellordistribute a Jarvis product, youmust provide the purchaserwith the appropriate safety
sheets and tool brochure. Additional copies of safety sheets and tool brochures will be provided uponrequest.
NOTICE TO EMPLOYER AND SAFETY DIRECTORAVOID INJURY
Keep hands clear.
notice to operators, maintenanceand cleanup personnel
Model SPC 100, 140, 141, 142, 165, 165B, 165G, 165GT and 165Jpage 3 of 16
PRODUCTS CORPORATION33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
1. Disconnect the air hose in accordance with OSHA’s lockout/tagout procedures (29 CFR 1910.147)before making any blade changes.
2. Disconnect the air hose in accordance with OSHA’s lockout/tagout procedures (29 CFR 1910.147)before performing any repairs or maintenance.
3. Disconnect the air hose -- or have the air hose disconnected -- in accordancewithOSHA’s lockout/tag-out procedures (29 CFR 1910.147) before performing any cleanup.
4. Disconnect the air hose when the tool is not in use.
5. Never put fingers, hands or other parts of the body on the cutting edge or within the cutting path ofthe tool when it is connected to an air supply.
6. Test the tool prior to use or daily. Depress the trigger and the tool should start; release the triggerand the tool should stop. If the tool malfunctions, remove it from service and report or repair it im-mediately.
7. Never depress the trigger unless you want to use or test the tool.
8. Never make modifications or alterations to the tool. Replace any missing or illegible labels.
9. Always wear eye protection in accordance with OSHA’s eye and face protection requirements (29CFR 1910.133) while operating the tool.
10. Always use both hands when starting and operating the tool to avoid the risk of possible “kick back”or “recoil”. Continue holding the tool with both hands until the saw blade comes to a complete stop.
NOTICE TO OPERATORS, MAINTENANCE AND CLEANUP PERSONNELREMOVE ANY MALFUNCTIONING TOOL FROM SERVICE
REPORT ANY PROBLEMS TO YOUR SUPERVISOR
Keep hands clear.
parts diagram and listModel SPC 100, 140, 141, 142, 165, 165B, 165G, 165GT and 165J page 4 of 16
®JARVIS6201008;:.
PRODUCTS CORPORATION33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
3016309 Housing and Gear Assy, SPC140 and 165 (includes items10, 11, 13--31 and 34--40)
ITEM PART NO. PART NAME QTY3016385 Hsg. & Gear Assy, SPC1413016384 Hsg. & Gear Assy, SPC142
(incls. items 13--31 & 34--40)21 1021376 Ball Bearing 422 1004298 Cup Washer 123 1055370 Socket Head Cap Screw 124 1002364 Bearing Cover with item 25 125 1038022 Grease Fitting 226 1021373 Needle Bearing 127 1026177 Planetary Ring Gear 128 1055371 Socket Head Cap Screw 129 1030092 Key, Round Ends 130 1026175 Pinion Gear 131 1021374 Inner Race 132 1042327 Hanger Bracket 133 1055609 Hex Head Screw 134 1010394 Gear Shaft Pin 335 1021377 Needle Bearing 336 1026178 Planetary Gear 337 1004299 Washer 638 1020269 Gear Carrier Shaft 139 1013248 External Retaining Ring 140 1055909 Cheese Head Screw 141 1030091 Key, Square Ends 142 1019001* Straight Handle 143 1004003* Lock Washer 144 1055802* Hex Head Screw 145 1055835 Flat Head Screw 246 1033012* Depth Gage Index 147 1055901* Oval Head Screw 2
ITEM PART NO. PART NAME QTY
**
***
**
*
*
*
*
*
*
***
Blade, handle and guard assemblies used on SPC 140 and SPC165 models only. See Figures C, D, E, F and G on pages 6--10for other SPC model blade, handle and guard assemblies.
YY
Y Optional T--handle assembly (items 6--8) for SPC 140 andSPC 165 models only.
H
HH
Not used on SPC 141 and SPC 142 models. See Figure E onpage 8 for SPC 141 and SPC 142 blade and guard assembly.
Figure ASPC--140 and 165
Y
D
D Not used on the SPC 165B model. See Figure F on page 9for SPC 165B blade and guard assembly.
* Small spacer must be installed with large deflector andlarge spacer must be installed with small deflector. Do notmix spacers or deflectors from their respective pairing.
** Optional spinal cord blade. Do not use items 129through 135 when installing optional blade item 140.
*
**
**
Figure E
Fastener Torque:d: 15.5 lbf--ft (21 N--m)
d
d
d
parts diagram and listModel SPC 100, 140, 141, 142, 165, 165B, 165G, 165GT and 165Jpage 9 of 16
PRODUCTS CORPORATION33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
SPECIFICATIONSMotor Power 0.85 hp 630 WOperating Pressure 90 psi 6.2 barAir Consumption 27.3 ft3/min 0.77 m3/minCut Speed 1775 rpmControl Handle Single Trigger PneumaticBlade Diameter 6.5 in 165 mm
5.5 in 140 mm3.9 in 100 mm
Cutting Depth (max)SPC165, SPC165B, SPC165J 2.0 in 50.8 mmSPC100 0.75 in 19.0 mmSPC140 1.5 in 38.1 mmSPC141 1.0 or 0.75 in 25 or 19 mmSPC142 1.4 in 35.6 mmSPC165G Pork (13 mm) 0.81 in 20.6 mmSPC165G Beef (16 mm) 0.88 in 22.4 mmSPC165GT (Tail) 0.24 in 6 mmOverall Length (not SPC165G)16.5 in 419 mm
SPC 165G, SPC 165GT 15.5 in 394 mmWeight (not SPC165G) 5.85 lbs 2.65 kg
INSTALLATION INSTRUCTIONS1 Optional: Suspend the SPC165 from a balancer.Jarvis part number 4042033 is available.
2 Make the necessary air connection.2.1 The required compressed air supply is 27.3
ft3/min at 90 psi (0.77 m3/min at 6.2 bar).2.2 An air filter/regulator/lubricator (Jarvis part
number 3022003) must be installed in the airsupply line. Keep the lubricator filled at alltimes.
OPERATION INSTRUCTIONS1 Each day, before you begin operation, go throughthe following checklist:1.1 Make sure that the compressed air supply is at
the correct pressure and that the lubricator is upto the full mark. (Use Jarvis Air Mist Lubrica-tor Oil; if using a conventional air mist lubrica-tor set the feed rate at 8--10 drops per minute; ifusing amicro fog air mist lubricator set the feed
rate at 100 drops per minute. Note: Almost allair mist lubricators are of the micro fog type).
1.2 Make sure that the saw moves freely on the ba-lancer, if applicable.
2 Making the cut:2.1 Position the saw.2.2 Depress the trigger fully to start the saw and
make the cut.2.3 When the desired amount of cut is reached, re-
lease the trigger. This will stop the blade fromrotating. Continue holding the saw firmly withboth hands until the blade comes to a completestop.
2.4 Withdraw the saw from the carcass.
MAINTENANCE INSTRUCTIONS
IMPORTANT: ALWAYS DISCONNECT THE COM-PRESSED AIR SUPPLY IN ACCORDANCE WITHOSHA’S LOCKOUT/TAGOUT PROCEDURES (29 CFR1910.147) WHEN INSTALLING OR REMOVING THEBLADE. ALWAYS DISCONNECT THE AIR SUPPLY INACCORDANCE WITH OSHA’S LOCKOUT/TAGOUTPROCEDURES (29 CFR1920.147) BEFOREPERFORM-ING ANY MAINTENANCE OR REPAIRS.
Refer to Figures A through G on pages 4 through 10 forreferenced items.1 DAILY:1.1 Four (4) times per day, add Jarvis 1315 White
Grease to the grease fittings (items 25) on thegear housing and bearing cover (items 20 and24).
1.2 At the end of the shift/day, flush the air motor(items 50--61).
4.8.4 Inspect all parts for wear and replace if nec-essary.
4.8.4.1 Remove and replace blade scrapers(item 154) as necessary.
5 BLADE INSTALLATION:5.1 Reverse procedures and steps outlined in section
4. Refer to applicable SPC saw model.5.1.1 For model SPC 141 with dual blades:
spacer (item 133) and deflector (item 135)must be installed as a matched pair (smallspacer with large defector and large spacerwith small deflector). Donotmix spacers ordeflectors from their respective pairing.
5.1.2 To ensure proper fit and safe operation, theslinger (item 13, 102 or 156) and saw blade(item 12, 86 or 158) or blade insert holder(item 101) must fit securely on the lip ofcrown gear shaft (item 18, 108 or 155).
5.1.3 The teeth or blade inserts at the bottom ofthe blade or blade insert holder should pointtoward the operator and rotate counter--clockwise.
justable studs (item 94) and blade scraper (item95).
6.2 Inspect all parts for wear and replace, as neces-sary.
7 BLADE SCRAPER ASSEMBLY: (SPC 165G)7.1 Reverse step 6.1.7.2 With hex screws (item 93) only finger tight, ro-
tate adjustable studs (item 94) until blade scrap-er (item 95) just contacts the blade inserts on theblade insert holder. Backoff the adjustable studs1/16 of a turn. Tighten hex screws.
8 GEAR HOUSING DISASSEMBLY:8.1 Remove blade as described in section 4. Refer
164 or 166, as applicable). See Figures A, C, D,E and F for applicable blade guard assembly.
8.3 Remove (2) screws (item 71) from valve assem-bly (item 76 or 173) and set applicable valve as-sembly aside.
8.4 Unscrew the motor housing (item 49) from thegear housing (item 20).
8.4.1 A motor tightening tool, part number
8039114 is available to grasp the motorhousing. See Figure 1.
MOTOR TIGHTENINGTOOL 8039114
Figure 1
8.5 Remove (3) screws (item 15) from gear housingcover (item 16), and remove the slinger (item13) and gear housing cover (item 16).
8.6 Remove oil seal (item 14) and o--ring (item 17).8.7 Unscrew the bearing retaining cover (item 24)
from the gear housing (item 20).8.7.1 A bearing cover wrench, part number
8039115 is available. See Figure 2.
BEARING COVERWRENCH 8039115
Figure 2
8.8 Place a wrench on the flats of the crown gearshaft (item 18), and remove screw (item 23) andcup washer (item 22).
8.9 Tap the gear housing with a nylon mallet on theflat area near the blade guard mounting pad todislodge the crown gear and shaft assembly(items 18, 19 and 41).
8.9.1 Separate the crown gear shaft (item 18)from the crown gear (item 19) using an ar-bor press, if necessary.
8.10 Turn the gear housing (item 20) over and pressthe (2) bearings (item 21) from the housing.
8.11 Tap the back face of the gear housing with a ny-lon mallet to dislodge the pinion gear shaft andcarrier (items 28--31, and 34--39). Be careful notto damage the internal threads.
8.12 Disassemble the pinion gear shaft.8.12.1 Remove (3) planetary gears and shafts
(items 34--37) from the gear carrier shaft(item 38) by pulling them straight out oftheir slots.
maintenance instructionsModel SPC 100, 140, 141, 142, 165, 165B, 165G, 165GT and 165Jpage 15 of 16
PRODUCTS CORPORATION33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
8.12.4 Remove screw (item 28) from pinion gear(item 30). Press pinion gear and bearing in-ner race (item 31) from the gear carrier shaftas an assembly. This can be achieved byinstalling an m5 x 40 mm long steel (do notuse a stainless steel screw) socket head capscrew into the tapped hole occupied by item28. Support the needle bearing inner race(item 31) on blocks in an arbor press, andpress the m5 screw and gear carrier shaftfrom the pinion gear and bearing race as-sembly.
8.13 Tap the end of the gear housing smartly with anylon mallet to dislodge the planetary ring gear(item 27).
8.13.1 A ring gear extractor tool, part number8039116 is available if gear is intractable.See Figure 3.
RING GEAR EXTRACTOR8039116
Figure 3
8.14 Remove needle bearing (item 26) from gearhousing.
8.14.1 A needle bearing removal tool, part number8039118 is available. See Figure 4.
NEEDLE BEARINGREMOVAL TOOL 8039118
Figure 4
8.15 Inspect all parts for wear and replace as neces-sary.
9 GEAR HOUSING ASSEMBLY:9.1 Reverse procedures and steps outlined in section
8. See special notes below.9.1.1 Ensure that the slot in the planetary ring gear
face (item 27) is aligned with the anti--rota-tion screw (item 40) during installation.
9.1.2 Insert needle bearing (item 26) into gearhousing (item 20) and tap lightly into place.Aneedle bearing insertion tool, part number8039152 is available. See special tools,page 11.
9.1.3 Apply Loctite 242 thread retaining com-pound to screws (items 23 and 28).
10 AIR MOTOR DISASSEMBLY:10.1 Remove valve assembly from motor housing as
described in section 8.10.2 Remove motor housing (item 49) from gear
housing (item 20) as described in section 8, step8.4.
10.3 Remove retaining ring (item 82) and exhaustplate (item 61).
10.4 Tap on the end of the motor housing (item 49)with a rubbermallet to dislodge the airmotor as-sembly (items 50 through 60).
10.5 Remove motor housing from air motor assem-bly.
10.6 Remove manifold assembly (item 59).10.6.1 An air motor repair tool kit, part number
8039151 is available to remove the man-ifold assembly from motor assembly. SeeFigure 5.
KEY8039042
LOCKINGCOLLAR8039041
COMPLETEAIR MOTOR REPAIR
KIT 8039151
LOCKINGSLEEVE 8039117
Figure 5
10.6.2 Place the locking sleeve into vise. Do notover-- tighten.
10.6.3 Place locking collar onto locking sleeve.
maintenance instructionsModel SPC 100, 140, 141, 142, 165, 165B, 165G, 165GT and 165J page 16 of 16
®JARVIS6201008;:.
PRODUCTS CORPORATION33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
10.6.4 Slide airmotor assembly into locking sleevewith manifold end down. See Figure 6.
AIR MOTORASSEMBLY
SCREW
MANIFOLD
SLEEVE
AIR MOTORREPAIR TOOL
Figure 6
10.6.5 Tighten the screw located on the lockingcollar of the air motor repair tool to lock themanifold assembly (item 59).
10.6.6 Pull on sleeve (item 55) of air motor assem-bly to removemanifold assembly (item 59).Do not score the air motor assembly.
10.7 Disassemble air motor assembly (items 50--60).10.7.1 A rotor bearing fixture and drive pin, part
numbers 8039150 and 8033006 are avail-able. See Figure 7.
LIP ON SLEEVE
DRIVE PIN 8033006
ROTOR BEARINGFIXTURE 8039150
AIR MOTORASSEMBLY
Figure 7
10.7.2 Place rotor bearing fixture on arbor press.10.7.3 Place air motor assembly on the rotor bear-
ing fixture. Note that the ears (lip on thesleeve, item 55) should hold the air motorassembly in the fixture.
10.7.4 Position the small diameter end of the drivepin onto the center of rotor shaft (item 53)and press.
10.7.5 Ball bearing (item 58) should now be sepa-rated from rotor (item 53).
10.7.6 Remove (2) disk springs (item 57).10.7.7 Remove rear end plate (item 56).10.7.8 Remove sleeve (item 55).10.7.9 Remove (5) vanes (item 54).10.7.10 Remove sun gear (item 50).10.7.10.1 Place locking sleeve of air motor repair
kit into vise. Do not over tighten.10.7.10.2 Place rotor (item53) into locking sleeve
with sun gear facing up. See Figure 8.
SUN GEAR
KEY
ROTOR
LOCKING SLEEVE
Figure 8
10.7.10.3 Align vane slot of rotor with slot oflocking sleeve. Slip key into the vaneslot in rotor (item 53).
10.7.10.4 Use a 6 mm Allen wrench to unscrewand remove the sun gear (item 50) fromthe rotor.
10.7.11 Remove rotor spacer (item 51).10.7.12 Remove front end plate (item 52).10.7.13 Press the ball bearing (item 21) from the sun
gear.10.8 Inspect all parts for wear and replace as neces-
sary.11 AIR MOTOR ASSEMBLY:11.1 Reverse procedures and steps outlined in section
10. See special notes below:11.1.1 Apply Loctite 242 thread retaining com-
pound to the rotor threads before installingsun gear.
11.1.2 Apply a liberal coating of Jarvis 1315White Grease to ball bearings (items 21 and58). Fill the bearing cavity in the manifoldassembly (item 59) with grease prior toinstallation.
11.1.3 Lubricate the gland (item 78) to preventdamaging the o--ring (item 60).