Page 1
1
AUTODESK INVENTORانجمن اینونتور ایران/ هندبوک مهندسی نرم افزار
Autodesk Inventor Engineer s Handbook
انجمن اینونتور ایران
www.irinventor.com
[email protected] :
[email protected]
Tel: 09352191813 &
021-46088862
قابل توجه خوانندگان عزیر: کلیه مطالب [
Autodeskاین هندبوک از سایت شرکت
]کپی برداری شده است.
Autodesk Inventor هندبوک مهندسی نرم افزار
Joints / Movable Joints
Parallel Spines
Generator
Page 2
2
AUTODESK INVENTORانجمن اینونتور ایران/ هندبوک مهندسی نرم افزار
Spline calculations in metric units
Transferred torque
where:
P transferred power [kW]
n speed [rpm]
Pressure on groove supporting surface
1. shaft inside diameter d h > 0
a)
b) if d min ≤d h -> d min = 1.1 d h [mm]
c) if d min ≤ 1.5 d h -> d min = 1.5 d h [mm]
2. shaft inside diameter d h = 0
where:
d min minimal shaft diameter [mm]
d h shaft inside diameter [mm]
T torque [Nm]
Page 3
3
AUTODESK INVENTORانجمن اینونتور ایران/ هندبوک مهندسی نرم افزار
K a application factor
K f fatigue-life factor
S v desired safety
τ Al Allowable Shear Stress
Minimum splines length to transfer the torque
1. Fixed connection:
2. Flexible connection:
where:
T torque [Nm]
K a application factor
K f wear-life factor
K w application factor
K m load distribution factor
S v desired safety
d s middle diameter = (D + d) / 2 [mm]
D outside diameter of groove section [mm]
d inside diameter of groove section [mm]
N number of grooves [-].
h height of groove = (D - d) / 2 [mm]
s chamfer
h st connection height h st = h - 2 s [mm]
Page 4
4
AUTODESK INVENTORانجمن اینونتور ایران/ هندبوک مهندسی نرم افزار
p Dmin allowable pressure on supporting surface of shaft or groove [MPa]
Allowable pressure
1. Fixed connection:
2. Flexible connection:
where:
T torque [Nm]
K a application factor
K f wear-life factor
K w application factor
K m load distribution factor
S v desired safety
d s middle diameter = (D + d) / 2 [mm]
D outside diameter of groove section [mm]
d inside diameter of groove section [mm]
N number of grooves [-].
h height of groove = (D - d) / 2 [mm]
s chamfer
h st connection height h st = h - 2 s [mm]
l f active key length [mm]
Strength Check
p min ≤ p ds
Page 5
5
AUTODESK INVENTORانجمن اینونتور ایران/ هندبوک مهندسی نرم افزار
p min ≤ p dh
where:
p min minimal calculated h/2 pressure [MPa]
p ds allowable pressure in shaft [Mpa]
p dh allowable pressure in hub [Mpa]
Page 6
6
AUTODESK INVENTORانجمن اینونتور ایران/ هندبوک مهندسی نرم افزار
Spline calculations in English units
Transferred torque
where:
P transferred power [lb ft]
n speed [min -1 ]
Pressure on groove supporting surface
1. shaft inside diameter d h > 0
a)
b) if d min ≤d h -> d min = 1.1 d h [mm]
c) if d min ≤ 1.5 d h -> d min = 1.5 d h [mm]
2. shaft inside diameter d h = 0
where:
d min minimal shaft diameter [in]
d h shaft inside diameter [inm]
Page 7
7
AUTODESK INVENTORانجمن اینونتور ایران/ هندبوک مهندسی نرم افزار
T torque [lbft]
K a application factor
K f fatigue-life factor
S v desired safety
τ Al Allowable Shear Stress
Minimum splines length to transfer the torque
1. Fixed connection:
2. Flexible connection:
where:
T torque [lbft]
K a application factor
K f wear-life factor
K w application factor
K m load distribution factor
S v desired safety
d s middle diameter = (D + d) / 2 [in]
D outside diameter of groove section [in]
d inside diameter of groove section [in]
N number of grooves [-]
h height of groove = (D - d) / 2 [in]
s chamfer
Page 8
8
AUTODESK INVENTORانجمن اینونتور ایران/ هندبوک مهندسی نرم افزار
h st connection height h st = h - 2 s [inm]
p Dmin allowable pressure on supporting surface of shaft or groove [psi]
Allowable pressure
1. Fixed connection:
2. Flexible connection:
where:
T torque [lb ft]
K a application factor
K f wear-life factor
K w application factor
K m load distribution factor
S v desired safety
d s middle diameter = (D + d) / 2 [in]
D outside diameter of groove section [in]
d inside diameter of groove section [in]
N number of grooves [-]
h height of groove = (D - d) / 2 [in]
s chamfer
h st connection height h st = h - 2 s [in]
l f active key length [in]
Strength Check
Page 9
9
AUTODESK INVENTORانجمن اینونتور ایران/ هندبوک مهندسی نرم افزار
p min ≤ p ds
p min ≤ p dh
where:
p min minimal calculated h/2 pressure [psi]
p ds allowable pressure in shaft [psi]
p dh allowable pressure in hub [psi]
------------------------------------------------------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------------------------------------------------------------
Web: www.irinventor.ir Email: [email protected] & [email protected] Tel: 09352191813 & 021-46088862