Inventia sp. z o.o. All rights reserved Telemetry Modules Quick Start
Mar 31, 2015
Inventia sp. z o.o. All rights reserved
Telemetry ModulesQuick Start
Inventia sp. z o.o. All rights reserved
Necessary Software
Microsoft Framework 1.1 MTManager MT-Data Provider v2.4 Mod-Dog Softing OPC or other OPC client
All programs should be installed with default settings
Inventia sp. z o.o. All rights reserved
Configuring MT-301 with MTM
3. Add new module right-clicking on project name
1. Run MTM
2.
2. Enter project name
Inventia sp. z o.o. All rights reserved
Configuring MT-301 with MTM
4. Enter module name and chose type and firmware
Tip:If you don’t know which firmware version do you have, choose the default one. During reading or writing configuration MTM will point you the right one. Then use Change version option from right click menu to correct settings.
Inventia sp. z o.o. All rights reserved
Configuring MT-301 with MTM
5. Choose General from Device list In SIM card PIN number field enter PIN card number that you
plan to use. Make sure that Use of GPRS option is set to “Yes”
Inventia sp. z o.o. All rights reserved
Configuring MT-301 with MTM
6. Click GPRS in Device list. Enter your APN name, APN user name and APN login password if required.
Inventia sp. z o.o. All rights reserved
Configuring MT-301 with MTM
7. Expand Authorized numbers in Device list and choose IP subcategory. Enter IP Number of SIM card that will be used in module connected to the PC.
Inventia sp. z o.o. All rights reserved
Configuring MT-301 with MTM
8. Click Resources in Device list and check Internal resources Modbus ID number. Here you can be set ID number allowing
access to the module internal resources from Modbus net.
Inventia sp. z o.o. All rights reserved
Configuring MT-301 with MTM
9. Connect MT-301 to PC using RS cable
10. Click Environment button
11. Choose your COM port number and apply by clicking Write
Inventia sp. z o.o. All rights reserved
11. Click Connect to establish connection
12. Make sure your SIM card is installed. Then click Write and watch the progress bar.
Configuring MT-301 with MTM
13. Accept by clicking OK
Inventia sp. z o.o. All rights reserved
Configuring MT-301 with MTM
14. After a while module sholud log on to the APN. Such state is sygnalized by LEDs on module cover. They should blink like below.
Inventia sp. z o.o. All rights reserved
15. Add new module MT-202
Configuring MT-202 with MTM
16. Enter PIN and set Modem operating mode in General
17. Choose Transmision speed in Resources/Serial port, connect MT-202 and Write the configuration
Inventia sp. z o.o. All rights reserved
Add hardware in Windows Control Panel
18. In Control Panel click Add Hardware
19. Add new modem to the operating system
Inventia sp. z o.o. All rights reserved
Dial-up configuration
20. In Control Panel click „Network Connection”
21. Create a new connection
Enter acces numberEnter name of connection
Enter user name and password if needed
Inventia sp. z o.o. All rights reserved
Dial-up configuration
22. Connect MT-202 with PC using port 2 Tips: If the dial-up connectionhave failed, you can forcehandshake on the COM portfrom PC side:
23. Click on APN icon
24. Click Properties
Inventia sp. z o.o. All rights reserved
Dial-up configuration
25. In the bookmark Options change„Redialing options”
26. In the bookmark NetworkingChose TCP/IP protocol andClick Properties button
27. Click „Advanced” button
28. Uncheck „use default gateway…”checkbox
After that click 3 times „OK” and DIAL then you will see:
Inventia sp. z o.o. All rights reserved
MT- Data Provider – first steps
29.After installation go to destination directory: ”C:\Program Files\InVentia\MTopc2\” and open „sample.xml” in NOTEPAD
30.First step is to change default sample.xml file. You must enter IP numbers of remote module (MT-301)
31.Next move is entering IP number of SIM card that is mounted in the MT-202 module.
32. Here you should to put correct type of the module 33.In that area you configure what data you can read from or write toremote module. Default ID modbus is „1” just like in MTM.
Tip:
You can find moreinfo about XMLparameters inreadme.pdf locatedin MT Data Provider folder.
34. Now you can save and close sample.xml
Inventia sp. z o.o. All rights reserved
MT- Data Provider – first steps
35. From Start/All programs/Softing OPC toolbox… run Softing OPC.
32. Double Click on MT-OPC server will start driver33. Left click od DA Browse bookmark and right click on server IDAnd left click on „Add Item for all tags”
36. Click on the DA items bookmarks
Inventia sp. z o.o. All rights reserved
MT- Data Provider – first steps
37.Here you will see quality good for all configured tags in sample.xmlFor example „device—slave.BO0” is the binary output Q1Enter ‘1’ in this field and click write to send ‘1’ to the remote module
Inventia sp. z o.o. All rights reservedInventia sp. z o.o. All rights reserved
Congratulations!!!
You have configured your first telemetry system based You have configured your first telemetry system based
on module on module MT-MT-301301 produced by produced by InInVVentiaentia !!! !!!