INSTALLATION ROOF RAILS VERSION 1 P/N 08L02-TK8-100 …ROOF RAILS P/N 08L02-TK8-100. 2017 ODYSSEY DEC 2016. PARTS LIST. Left side roof rail. Right side roof rail Left front roof rail
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
The following tools are available through the Honda Tooland Equipment Program. On the iN, click on: Service >Service Bay > Tool and Equipment Program, then enterthe number under “Search”. Or, call 888-424-6857.
• Trim Tool Set (T/N SOJATP2014)
• Plastic Trim Tool (T/N SILTRIMTL10)
• Air Saw (T/N AT192A)
1 of 68L02-TK8-1001-91
Illustration of the Roof Rails Installed on the Vehicle
020101AB
RIGHT SIDEROOF RAIL
LEFT SIDEROOF RAIL
INSTALLATION
Customer Information: The information in thisinstallation instruction is intended for use only by skilledtechnicians who have the proper tools, equipment, andtraining to correctly and safely add equipment to yourvehicle. These procedures should not be attempted by“do-it-yourselfers.”
NOTE: Be extremely careful not to damage the roof andother finished surfaces of the body when installing the roofrails.
Installing the Roof Rails
1. Remove the left roof molding by carefully lifting itupward from four roof molding clips.
020104BB
LEFT ROOFMOLDING
4 ROOF MOLDINGCLIPS
FRONT
2 of 6 AII05287-2
2. Open the tailgate halfway. Using a trim tool, pry upon the rear end of the roof molding left cover.
020102AB
ROOF MOLDINGLEFT COVER TAILGATE
(Open the halfway.)
TRIM TOOL
FRONT
3. While wearing an eye protection, use an air saw tocut off the roof molding left cover at the scribe line asshown. Remove any burrs.
6. Measure and use a felt-tip pen to mark the left roofmolding as shown.
042701BB
FELT-TIPPEN
LEFT ROOFMOLDING
FRONT
MARKS
MARK
556 mm(21.9 in.)
150 mm(5.9 in.)
850 mm(33.5 in.)
95 mm(3.7 in.)
518 mm(20.4 in.)
MARKS
7. While wearing an eye protection, use an air saw tocut off the left roof molding at the mark made instep 6.
020107BB
AIR SAWLEFT ROOFMOLDING
FRONT
MARKS
MARKS
MARK
4 (1612) 3 of 6
8. Install one roof molding clip to the left roof molding(front).
QC30703AB
LEFT ROOFMOLDING(FRONT)
FRONT
ROOF MOLDINGCLIP
ROOF MOLDINGCLIP
LEFT ROOFMOLDING(FRONT)
FRONT
LEFT ROOF MOLDING(Make sure to install inthe correct direction.)
OUTSIDE
CENTERSIDE
9. Install the roof molding left cover.NOTE: If the roof molding cover is not even with theroof, it is installed incorrectly. Install the roof moldingcover properly.
020109AB
ROOF MOLDINGLEFT COVER
FRONT
TAILGATE
4 of 6 AII05287-2
10. Reinstall the left roof moldings back onto the roof ofthe vehicle as shown.
QC30704AB
FRONT
LEFT ROOFMOLDINGS
OUTSIDE
CENTERSIDE
FRONT
LEFT ROOF MOLDING(Make sure to install inthe correct direction.)
11. Install the left side roof rail with six Torx nuts. Makesure the roof rail is installed in the correct position.Torque the Torx nuts to: 10 N·m (7.3 lb·ft)
16. Attach the masking tapes to the vehicle panel.
061802AB
FRONT
MASKINGTAPES
LEFT SIDEROOF RAIL
VEHICLEPANEL
17. Hook the left center roof rail cover to the left side roofrail as shown.
020114BB
FRONT
LEFT CENTERROOF RAILCOVER
LEFT SIDEROOF RAIL
4 (1612) 5 of 6
18. Install the left center roof rail cover to the left sideroof rail as shown. Make sure that the left center roofrail cover is no clearance between the left side roofrail.
061803AB
FRONTLEFT CENTERROOF RAILCOVER
LEFT SIDEROOF RAIL
FRONT LEFT SIDEROOF RAIL
LEFT CENTERROOF RAILCOVER
VIEWED FROM INSIDE
Turn.
Push.
19. Remove the masking tapes attached in step 16.
20. Repeat steps 1 through 19 for the right side of thevehicle.
USE AND CARE
Check the roof rail mounting bolts frequently, andre-tighten if necessary.