Illustration of the Roof Rack Rails Installed on the Vehicle. QD31801AA. RIGHT ROOF RACK RAIL LEFT ROOF RACK RAIL. . 2of6. ... through 17 to install the right roof rack rail. USE AND
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
The following tools are available through the Honda Tooland Equipment Program. On the iN, click on: Service >Service Bay > Tool and Equipment Program, then enterthe number under “Search”. Or, call 888-424-6857.
• Plastic Trim Tool (T/N SILTRIMTL10)
• Air Saw (T/N AT192A)
Illustration of the Roof Rack Rails Installed on theVehicle
QD31801AA
RIGHT ROOFRACK RAIL
LEFT ROOFRACK RAIL
1 of 68L02-T0A-1A00-90
www.collegehillshonda.com
INSTALLATION
Customer Information: The information in thisinstallation instruction is intended for use only by skilledtechnicians who have the proper tools, equipment, andtraining to correctly and safely add equipment to yourvehicle. These procedures should not be attempted by“do-it-yourselfers.”
NOTE:
• Be extremely careful not to damage the roof and otherfinished surfaces of the body when installing the roofrack rails.
• The weight of the cargo must not exceed the maximumweight capacity of 75 kg (165 lbs).
Installing the Roof Rack Rails
1. Measure rearward from the windshield molding, andmark the left roof molding at the measurementshown.
QA11301AD
LEFT ROOFMOLDING
FRONT
17 mm(0.7 in.)
MARKLEFT ROOFMOLDING
WINDSHIELDMOLDING
FELT-TIPPEN
2 of 6 AII 52537
2. Using a plastic trim tool, pry up on the left roofmolding cover to release one retaining tab and oneclip.
QA22108AD
FRONT
LEFT ROOFMOLDING COVER
CLIP
RETAIN-ING TAB
PLASTICTRIMTOOL
TAILGATE
3. Pull the left roof molding toward the outside ofvehicle to release the locking tab, and then press thelocking tab toward the inside of vehicle, and releasethe left roof molding from the vehicle. Whenremoving the left roof molding, start from the rear ofvehicle and work towards the front.
4. While pulling up the left roof molding, remove the two
clips. Insert the plastic trim tool alternately to eachslots in the clip, and release the locking tabs in theorder shown. When removing the left roof molding,start from the rear of vehicle and work towards thefront. Be careful not to deform the roof molding.
5. Place a blanket over the roof of vehicle under the leftroof molding. Be careful not to deform the roofmolding when measuring and cutting.
Q0D0802CD
LEFT ROOFMOLDING
FRONT
BLANKET
6. Place an empty cardboard box (approx. 120 mm tall)under the left roof molding near the mark.
Q0D0803BD
LEFT ROOFMOLDING
MARK
EMPTYCARDBOARDBOX
Approx.120 mm(4.7 in.)
FRONT
(1409) 3 of 6
www.collegehillshonda.com
7. While wearing an eye protection, use an air saw to
cut the left roof molding at the mark. Do not use acutting wheel or shears to cut the left roof molding, itwill damage the left roof molding. Have an assistanthold the rear edge while cutting.
Q0D0804BD
LEFT ROOFMOLDING
MARKAIR SAW
FRONT
8. Remove the cardboard box and blanket.
9. Secure the roof molding to the two clips removed instep 4.
QA60802AG
LEFT ROOFMOLDING
2 CLIPS
FRONT
4 of 6 AII 52537
10. Insert flat-tip screwdrivers alternately between thegreen clip and the stud bolt as shown. While pullingon the green clip, release the locking tab on thegreen clip from the groove on the stud bolt notch bynotch, and remove the green clip. Repeat the sameprocedure to remove the two purple clips.
Q0D0805BD
FRONT
FLAT-TIPSCREWDRIVERS(Alternately insert torelease the locking tab.)