Parts marked with this symbol are officially licensed products of Chrysler LLC. Back-Up Lamp Assemblies 16 Battery J-Bolt and Hardware 7 Battery Retainers 7 Battery Trays 7 Bumper Bolt Sets 3 Bumper Brackets 3 Bumpers 3 Convertible Pillar Post Weatherstrips 20 Convertible Weatherstrip Kits 19 Cowl Dash Panel 7 Cowl Side Panels 7 Cross Rails, Rear 16 Deck Filler Panels 14 Deck Latch Support Braces 14 Door Bumpers 9 Door Jamb Pillars 12, 13 Door Lock Knobs 9 Door Shells 8 Fender Ornaments 5 Fender Patch Panels 5 Fender Rear Splash Shields 5 Fenders, Front 4 Fender to Cowl Mount Braces and Brackets 5 Firewalls 7 Floor Mats 21 Floor Pan, Rear 10 Floor Pan Braces 10 Floor Pan Patches, Partial 10 Floor Pans (Back Seat Footwell) 10 Floor Shifter Humps 10 Frame Rail Braces, Rear 16 Frame Rails 5 Frame Rails, Rear 15 Fuel Tank Strap Studs and Nuts 17 Gas Caps 17 Gas Tanks 17 Gas Tank Sending Units 17, 18 Gas Tank Straps 17 Grille Panels 4 Grilles 4 Header Panels 4 Headlamp Adjusting Screw & Nut 4 Headlamp Bezels 4 Hood Hinges 6, 19 Hood Insulation Pads 6 Hood Pad Clips 6, 19 Hoods 6 Hood Scoop Ornament Sets 6 Inner Fenders 5 Inner Fender Splash Shields 5 Paint Gasket Kits 19 Park Lamps 4 Partial Floor Pan Patches 10 Pillar Post Weatherstrips 20 Quarter Glass "U"-Seals 13 Quarter Panel Extensions (End Caps) 13 Quarter Panel Ornaments 13 Quarter Panels 11 Quarter Panel Skins 12 Quarter Patch Panels, Front 12 Quarter Patch Panels, Lower Rear 12, 13 Radiator Supports 5 Rear Spoiler Mounting Brackets 14 Rear Window Gaskets 20 Rocker Panels 9 Shock Absorbers 21 Side Marker Lenses 18 Spare Tire Hold-Down Brackets 15 Tail Lamp Assemblies 16 Tail Panels 16 Trunk Floors 15 Trunk Lids 14 Trunk Weatherstrip Gutters 14 Upper Control Arm Mounting Brackets 5 Valances, Front 4 Valances, Rear 16 Weatherstrip Kits 18, 19, 20 Wheel Arch Patch Panels 13 Wheelhouses, Outer Rear 13 Wheelhouses, Rear Inner 13 Window Regulator Handles 9 Windshield or Rear Window Gaskets 20 Windshield Reveal / Roofrail Drip Molding Kits 8 Wiper Blades 6 I NDEX
20
Embed
Index [musclecar-parts.com]musclecar-parts.com/MoparCatalogs/goodmark mopar.pdf · Parts marked with this symbol are officially licensed products of Chrysler LLC. High performance
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Parts marked with this symbol are officially licensed products of Chrysler LLC.
Parts marked with this symbol are officially licensed products of Chrysler LLC.
�
High performance Dodges and Plymouths were a dominant force on the streets and at the track back in the heyday of the muscle car . Today restorers are almost fanatic in their love for the Pentastar beasts of the sixties and seventies . But for a long time it has been nearly impossible to find quality reproduction parts for restoration or modification; especially sheet metal body parts . But today the restoration specialists at Goodmark Industries are hard at work building top quality fenders, quarter panels, and more parts for your favorite Mopar muscle car . Check out the following pages to find the parts you need . And keep your eye on the Goodmark website, as we have new parts in development all the time . Read on!
dodge & Plymouth
BumPers and grIlle Goodmark has new chrome steel bumpers and stainless steel hardware
to mount your new bumper . Our Premium Quality bumpers are chromed in the USA and are excellent quality . Always use new hardware for that freshly restored look!
Chrome BumpersNew chromed steel bumpers replace rusted or damaged originals . Our bumpers are triple nickle plated for durability and are great driver quality . Premium Quality bumpers are chromed in the USA and are excellent quality .
Bumper Bolt Sets Set of all the bolts you need to mount the front bumper to the brackets . The bolts that mount the brackets to the body are not included . 67-72 . . “A” Body (exc . '70-72 Dart) Front, '67-72 “B” Body Bumper Front or Rear . . . . . . . (except '68-70 Charger Rear, or '71-72 Plymouth "B" Front) (32 . . . . . . . pieces) (8 Bolts with Washers and Nuts} . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2111-001-69S . . . . . . .$16 .45 kit67-72 . . Mopar “A” Body Rear, '71-72 Plymouth “B” Body Front (24 Pieces) . . . . . . . (6 Bolts with Washers and Nuts) . . . .2111-801-69S . . . . . . .$14 .25 kit70-72 . . Dart Front, '70-74 “E” Front or Rear, '68-70 Charger Rear (16 Pieces) . . . . . . . (4 Bolts with Washers and Nuts) . . . .2161-001-68S . . . . . . .$10 .95 kit
Bumper BracketsEDP coated steel brackets used to mount the front bumpers . Sold in a set for one car .
(photo not available)70-72 . . Challenger Front Bumper Bracket Set . .2120-005-70S . . . . . $169 .95 set
Chrome Bumper GuardsNew chromed steel bumper guards replace rusted or damaged originals . Our guards are triple nickle plated for durability and are great driver quality . Cushions not included .
Front Fenders New steel bolt-on assemblies feature the headlamp panel and all the braces as originals, not just the outer skins . We have spent a considerable amount of time and money to make these fenders from scratch and the result is a beautiful fender we would be proud to put on our own cars . These have not been available for several years, so get yours now that they're available!
70-71 . . Challenger, Left / Right . . . . . . . . . . . . .2120-100-70L / R . . $599 .95 ea72-74 . . Challenger, Left / Right . . . . . . . . . . . . .2120-100-72L / R . . $599 .95 ea
70 . . . . . Barracuda, Left / Right . . . . . . . . . . . . . .2422-100-70L / R . . $599 .95 ea71 . . . . . Barracuda, except ‘Cuda, Left / Right . .2422-100-711L / R . $599 .95 ea
71 . . . . . ‘Cuda (with Gill Holes), Left / Right . . . .2422-100-712L / R . $649 .95 ea72-74 . . Barracuda, Left / Right . . . . . . . . . . . . . .2422-100-72L / R . . $599 .95 ea68 . . . . . Plymouth "B", Left / Right . . . . . . . . . . . .2432-100-68L / R . . . . . $Inquire69 . . . . . Plymouth "B", Left / Right . . . . . . . . . . . .2432-100-69L / R . . . . . $Inquire70 . . . . . Plymouth "B", Left / Right . . . . . . . . . . . .2432-100-70L / R . . . . . $InquireNOTE: '68-70 Plymouth "B" Fenders are currently under development.
Front Valances New EDP coated steel valances below the front bumper .
70 . . . . . Challenger Grille (painted Argent Silver, . . . . . . . paint Black for R/T or T/A) . . . . . . . . .2120-050-701 . . . . . $494 .95 ea70 . . . . . Challenger Headlamp Bezel, Left / Right . . . . . . . (Silver, paint Black for R/T or T/A) . . .2120-060-701L / R . . . . $InquireNOTE: '70 Challenger Headlamp Bezels are currently being tooled.72-74 . . Challenger Grille (painted Argent Silver, . . . . . . . paint Black for Rallye models) . . . . .2120-050-72 . . . . . . $219 .95 ea
NEW!
Look!
Parts marked with this symbol are officially licensed products of Chrysler LLC.
�
Fender to Cowl Mount Braces and Brackets New EDP coated steel braces or brackets that support the inner fender or mount the upper rear fender to the cowl panel . Commonly rusted or missing .
Fender Ornaments Set of 8 fender louvers, 4 mounting brackets, and 16 nuts to mount fender louvers for the special '71 'cuda fenders .71 . . . . . Barracuda 'cuda . . . . . . . . . . . . . . . . . . .2422-130-71S . . . . . $263 .95 set
Fender Patch Panels Steel patch panel used to repair the lower rear part of the front fender (between the front wheel and the door), a common rust area . 68-70 . . Coronet, Left / Right (8" high) . . . . . . . .2132-190-68L / R . . $164 .95 ea
Fender Rear Splash ShieldsSteel panel that keeps water and debris from entering the rear of the fender .
68 . . . . . "B"-Body, Left / Right . . . . . . . . . . . . . . .2132-345-68L / R . . . . . $Inquire69-70 . . "B"-Body, Left / Right . . . . . . . . . . . . . . .2161-345-68L / R . . . $49 .95 ea
Radiator SupportsNew steel EDP coated panels repair or replace a commonly rusted area .
Heavy rubber die-cut seals that keep dirt and water out of the engine compartment . Staples are included to attach to the inner fenders . 70-74 . “E”, '71-72 "B" Body, Left / Right pair . . .2120-351-70P . . . . . . . $21 .95 pr66-70 . . "B" Body, Left / Right pair . . . . . . . . . . . .2131-351-66P . . . . . . . $16 .45 pr
Upper Control Arm Mounting Brackets
Steel EDP coated brackets and gussets that mount the front Upper Control Arms . 70-74 . “E” Body, '62-70 “B” Body . . . . . . . Gusset, Left / Right . . . . . . . . . . . . . .2130-325-625L / R . . $54 .95 ea . . . . . . . Bracket, Left / Right . . . . . . . . . . . . .2130-325-626L / R . $164 .95 ea
Front Frame RailsComplete factory style front frame rails for popular models .
(photo not available)70-74 . “E”-body Front Frame Rail, Left / Right .2120-390-70L / R . . $439 .95 ea66-69 . . "B"-body Front Frame Rail, Left / Right .2131-390-661L / R . . . . $InquireNOTE: "B"-Body front frame rails are currently under development.
Look!
Parts marked with this symbol are officially licensed products of Chrysler LLC.
�
Hoods New steel EDP coated hood is actually patterned off of a '71-74 hood, so '70 owners will have to use the later '71-74 style hinges . Also, emblem and molding holes are not punched and will need to be added if required .
70-71 . . "E" Body (with Shaker hood) . . . . . . . Shaker Hood Scoop . . . . . . . . . . . . .2120-255-703 . . . . . . . . $Inquire . . . . . . . Shaker Hood Scoop Grille, L / R . . . .2120-255-704L / R . . . . $Inquire . . . . . . . Challenger Trim Ring . . . . . . . . . . . .2120-255-705 . . . . . . . . $Inquire . . . . . . . Barracuda Trim Ring (w/ gasket) . . .2422-255-702 . . . . . $219 .95 ea . . . . . . . Trim Ring Nut Kit (14 pieces) . . . . . .2120-255-705S . . . . . . .$5 .45 kitNOTE: All parts not priced are currently under development.
Hood Insulation PadsBrand new die-cut insulation pads that fit under the hood and keep the engine heat from baking the paint on the hood, as well as keep underhood noise to a minimum . Each pad includes matching clips .
. . . . . . . Cowl to Inner Fender Brace, LH / RH . .2131-352-66L / R . . . $49 .45 ea
Lower Cowl Side Panels New EDP coated steel panels behind the rear of the fender . These are the panels the door hinges bolt to . 70-74 . “E” Body, Left / Right . . . . . . . . . . . . . . .2120-385-703L / R . $219 .95 ea68-70 . . "B"-body, Left / Right . . . . . . . . . . . . . . .2132-385-68L / R . . . . . $InquireNOTE: "B"-body Lower Cowl Side Panels are currently under development.
NEW!
Parts marked with this symbol are officially licensed products of Chrysler LLC.
�
Door Hinge Pillars(photo not available)
70-74 . . "E"-body Coupe Front Hinge Pillar Assembly, . . . . . . . Left / Right . . . . . . . . . . . . . . . . . . . . .2120-406-70LS / RS $449 .95 ea . . . . . . . Front Lower Pillar Assembly, . . . . . . . Left / Right (from 6/1/70) . . . . . . .2120-406-702L / R . $169 .95 ea . . . . . . . Outer Windshield Pillar, Left / Right .2120-406-703L / R . . . . $Inquire68-70 . . "B"-body 2-door Hardtop Outer Windshield Pillar Post, . . . . . . . Left / Right . . . . . . . . . . . . . . . . . . . . .2132-406-681L / R . . . . $InquireNOTE: These parts are all currently under development.
Roof Skins New steel outer roof skin and braces replace a common rusted area, especially on cars originally equipped with a vinyl top .
Windshield Reveal / Roofrail Drip Molding KitsNew stainless steel moldings that trim the front or rear windshield or the roofrail drip rail . Sold in sets for one car . 68-70 . . "B" Body 2-door (except Convertible) . . . . . . . Front Windshield Kit (5-pieces) . . . . .2132-525-68S . . . . . . . . $Inquire68-70 . . "B" Body 2-door (except Charger or Convertible) . . . . . . . Rear Window Kit (4-pieces) . . . . . . .2132-715-68S . . . . . . . . $Inquire68-70 . . Plymouth "B" Roofrail Gutter Set, . . . . . . . Left / Right Pair . . . . . . . . . . . . . . . . .2432-926-69P . . . . . . . . $InquireNOTE: All these items are currently under development.
Windshield Reveal Molding Clip KitsSets of clips used to install the front or rear window reveal moldings . These are not included with the molding kits, and must be ordered separately
Door Handle and Lock Cylinder GasketsUsed when replacing door handles and lock cylinders . These are included with our Paint Seal Kits and Weatherstrip Kits .
Rocker PanelsNew EDP coated steel full factory style inner and outer rocker panels to correctly repair rusty rockers .
(photo not available)70 . . . . . "E" Body Coupe Inner Front, Left / Right . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2120-460-701L / R . . $99 .95 ea71-74 . . "E" Body Coupe Inner Front, Left / Right . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2120-460-71L / R . . . $99 .95 ea70-74 . . Challenger Coupe . . . . . . . Inner Rear, Left / Right . . . . . . . . . . .2120-460-702L / R . . $49 .95 ea . . . . . . . Outer, Left / Right . . . . . . . . . . . . . . .2120-470-701L / R . $279 .95 ea70-74 . . Barracuda Coupe . . . . . . . Inner Rear, Left / Right . . . . . . . . . . .2422-460-70L / R . . . $49 .95 ea . . . . . . . Outer, Left / Right . . . . . . . . . . . . . . .2422-470-701L / R . . . . $Inquire66-70 . . "B" Body (except Convertible), . . . . . . . Inner Front, Left / Right . . . . . . . . . . .2131-460-661L / R . . $99 .95 ea . . . . . . . Inner Rear, Left / Right . . . . . . . . . . .2131-460-662L / R . . $49 .95 ea68-70 . . "B" Body (except Convertible) . . . . . . . Outer, Left / Right . . . . . . . . . . . . . . .2132-470-681L / R . . . . $InquireNOTE: All parts not priced are currently being tooled.
1-Piece Floor Pan, Front New steel EDP coated 1-piece Front Floor Pan replaces the factory panel seam to seam . Be sure to also order the extension pieces and under rear seat panel if required . Don't forget your floor braces if required .
Parts marked with this symbol are officially licensed products of Chrysler LLC.
10
1-Piece Floor Pan, Front (continued)
68-70 . . "B" Body 1-Piece Front Floor Pan . . . . .2132-505-68 . . . . . . $549 .95 eaNOTE: Can be used for 1966-67 models but is not correct.
Center Floor Pans (Back Seat Footwell) New EDP coated steel panels replace the factory center floor pan extensions to the factory seams .
70-74 . . Challenger, Left / Right . . . . . . . . . . . . .2120-510-70L / R . . $109 .95 ea70-74 . . Barracuda, Left / Right . . . . . . . . . . . . . .2422-510-70L / R . . $109 .95 ea
68-70 . . "B" Body, Left / Right . . . . . . . . . . . . . . .2132-510-68L / R . . $109 .95 ea
1-Piece Floor Pan, Rear
New EDP coated stamped steel panel replaces sheetmetal rusted under the back seat to the factory seams . Be sure to also order any of the brack-ets or braces you need under this panel separately . 70-74 . . “E” Body, (under rear seat) . . . . . . . . . .2120-511-721 . . . . . $439 .95 ea68-70 . . "B" Body (under rear seat) . . . . . . . . . . .2132-511-68 . . . . . . $439 .95 ea
Partial Floor Pan PatchesWe also sell these partial floor patches for models where full floors are not avail-able .
67-76 . . "A" Body Front (26" W x 25" L), L / R . . .2111-505-67L / R . . $109 .95 ea63-65 . . "B" Body Front ((25" W x 25" L), L / R . .2130-505-63L / R . . $131 .95 ea
67-76 . . "A" Body Rear (21" W x 19" L), L / R . . .2111-510-67L / R . . $109 .95 ea63-65 . . "B" Body Rear (23" W x 23" L), L / R . . .2130-510-63L / R . . $131 .95 ea
Floor Shifter HumpsThese are the steel humps used when a console-mounted 4-speed transmission is ordered and requires the special floor bulge to mount the shifter boot.
Parts marked with this symbol are officially licensed products of Chrysler LLC.
11
Quarter PanelsFull Quarter Panels New EDP coated steel full factory style and coverage quarter panels for hardtop models . These are not the side skins but full factory coverage panels . Each panel is complete factory dimensions seam to seam . Be sure to order the trunk weather-strip gutters with your new panels as they are not included . Also be sure to order outer wheelhouses and trunk drop-offs if needed . All quarters are shipped truck freight .
70-71 . . Challenger Hardtop, Left / Right . . . . . .2120-601-70L / R . . $599 .95 ea72-74 . . Challenger Hardtop, Left / Right . . . . . .2120-601-72L / R . . $599 .95 ea
70-71 . . Barracuda Hardtop, Left / Right . . . . . . .2422-601-70L / R . . $599 .95 ea72-74 . . Barracuda Hardtop, Left / Right . . . . . . .2422-601-72L / R . . $599 .95 ea
68 . . . . . Plymouth "B" Body 2-door, Left / Right .2432-601-68L / R . . $599 .95 ea69 . . . . . Plymouth "B" Body 2-door, Left / Right .2432-601-69L / R . . $599 .95 ea70 . . . . . Plymouth "B" Body 2-door, Left / Right .2432-601-70L / R . . . . . $Inquire
71 . . . . . Plymouth "B" Body 2-door, Left / Right .2433-601-71L / R . . $699 .95 ea72 . . . . . Plymouth "B" Body 2-door, Left / Right .2433-601-72L / R . . $699 .95 ea
Which type of “Quarter Panel” do you need? A “Full Quarter Panel” is made just like the panels which were welded onto your car when it was new . These panels reach all the way to each edge of the
rear quarter panel area, including the trunk and door edges, and reach to the roof line, just like the factory-original panels did for your particular model . For Dodges and Plymouths, the door jamb was never part of the original quarter panels .
“Quarter Skins” are nearly as large as “Full Quarter Panels”, but do not include any trunk lips or sail panel . They cover only the side of the quarter panel, and reach upward to approximately the location where the bottom of original vinyl roofs would normally be . Keep in mind that, while “Quarter Skins” initially cost less than “Full Quarter Panels”, it often takes more labor to install them . So, if keeping your costs down is the only reason that you might select “Quarter Skins” over “Full Quarter Panels”, you should be aware that the final net cost might not represent much of a savings . Also, “Quarter Skins” do require a lip to weld to, all the way around the edge . This makes them a poor choice for badly rusted-out cars or collision damage…since there is often no bottom edge remaining to weld to . In this case, you are better off choosing “Full Quarter Panels”, and adding Outer Wheel Houses to completely replace the rust .
“Quarter Patches” are just what they sound like…small pieces of quarter panels, for repairing small holes in isolated areas . These are good choices for nearly perfect cars with tiny holes in specific spots, or for low-budget “driver” cars . But it can be very difficult to hide the seam areas where the patches are welded to the original panels .
Full Quarter Panels….Your BEST Choice! If you have a car that is worth restoring, then it is probably worth
restoring right! Our top-quality Full Quarter Panels are made just like the factory made them originally, with lap seams, and they reach up to the roof line . Unquestionably, these are the best choice for any quality restoration of a Mopar body . Call today, or visit our website to place your order .
Parts marked with this symbol are officially licensed products of Chrysler LLC.
1�
Quarter Panel Skins New EDP coated steel panels cover the side of the quarter panel . They are not full panels, and do not include the sail panel, nor do they extend to the trunk opening, but go from the bottom up to the beltline and lip over the belt about 1" . Be sure to order outer wheelhouses and drop-offs if required . All quarter skins are shipped truck freight .
67-68 . . Dart, Left / Right, 28" H x 86" L . . . . . . .2111-600-67L / R . . $241 .95 ea69 . . . . . Dart, Left / Right, 28" H x 86" L . . . . . . .2111-600-69L / R . . $241 .95 ea
70-71 . . Dart Swinger / Valiant Scamp, Left / Right . . . . . . . (fits to '76, modify marker hole) 28" H x 86" L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2112-600-70L / R . . $241 .95 ea67 . . . . . Barracuda, Left / Right, 30" H x 79" L . .2421-600-67L / R . . $241 .95 ea
68 . . . . . Barracuda, Left / Right, 30" H x 79" L . .2421-600-68L / R . . $241 .95 ea69 . . . . . Barracuda, Left / Right, 30" H x 79" L . .2421-600-69L / R . . $241 .95 ea
70-71 . . Duster / Demon Left / Right, 32" H x 82" L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2150-600-70L / R . . $241 .95 ea72-76 . . Duster / Demon / Dart Sport Left / Right, 32" H x 82" L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2150-600-72L / R . . $241 .95 ea
70-71 . . Challenger, Left / Right, 32" H x 67" L . .2120-600-70L / R . . $252 .95 ea72-74 . . Challenger, Left / Right, 32" H x 67" L . .2120-600-72L / R . . $252 .95 ea
70-71 . . Barracuda, Left / Right, 32" H x 65" L . .2422-600-70L / R . . $252 .95 ea72-74 . . Barracuda, Left / Right, 32" H x 65" L . .2422-600-72L / R . . $252 .95 ea
Quarter Panel Skins (continued)
68 . . . . . Coronet, Left / Right, 32" H x 88" L . . . .2132-600-68L / R . . $274 .95 ea69 . . . . . Coronet, Left / Right, 32" H x 88" L . . . .2132-600-69L / R . . $274 .95 ea
70 . . . . . Coronet, Left / Right, 32" H x 88" L . . . .2132-600-70L / R . . $274 .95 ea68 . . . . . Charger, Left / Right, 32" H x 88" L . . . .2161-600-68L / R . . $274 .95 ea
69 . . . . . Charger, Left / Right, 32" H x 88" L . . . .2161-600-69L / R . . $274 .95 ea70 . . . . . Charger, Left / Right, 32" H x 88" L . . . .2161-600-70L / R . . $274 .95 ea
73-74 . . Charger, Left / Right, 35" H . . . . . . . . . .2133-600-73L / R . . $429 .95 ea68 . . . . . Plymouth “B”, Left / Right, 29" H x 88" L 2432-600-68L / R . . $274 .95 ea
69 . . . . . Plymouth “B”, Left / Right, 29" H x 88" L 2432-600-69L / R . . $274 .95 ea70 . . . . . Plymouth “B”, Left / Right, 29" H x 88" L 2432-600-70L / R . . $274 .95 ea
(photo not available)71 . . . . . Plymouth "B", Left / Right . . . . . . . . . . . .2433-600-71L / R . . $299 .95 ea72 . . . . . Plymouth "B", Left / Right . . . . . . . . . . . .2433-600-72L / R . . $299 .95 ea
Lower Front Quarter Patch PanelsPartial quarter sections that cover between the door opening and the rear wheel opening . Used for minor rust repair in this area .
68-70 . . Charger, measures 30" H x 33" W, . . . . . . . Left / Right . . . . . . . . . . . . . . . . . . . . .2161-623-68L / R . . $164 .95 ea71-72 . . Plymouth "B", Left / Right . . . . . . . . . . . .2433-610-71L / R . . $189 .95 ea
Parts marked with this symbol are officially licensed products of Chrysler LLC.
1�
Quarter Wheel Arch Patch Panels Partial quarter sections that cover around the rear wheel opening . Used for minor rust repair in this area .63-66 . . Dart, measures 20" H x 40" W, . . . . . . . Left / Right . . . . . . . . . . . . . . . . . . . . .2110-655-63L / R . . $153 .95 ea
Lower Rear Quarter Patch PanelsPartial quarter sections that cover between the rear wheel opening and the rear bumper . Used for minor rust repair in this area .
64-66 . . Dart, measures 20" H x 40" W, LH / RH 2110-690-64L / R . . $153 .95 ea70-76 . . Duster / Demon / Dart Sport, measures 16 .5" H x 45" W, . . . . . . . Left / Right . . . . . . . . . . . . . . . . . . . . .2150-690-70L / R . . $153 .95 ea68-70 . . Charger, measures 25" H x 52 .5" W, . . . . . . . Left / Right . . . . . . . . . . . . . . . . . . . . .2161-690-68L / R . . $175 .95 eaNOTE: Side Marker holes must be cut out as required.
71 . . . . . Plymouth "B", Left / Right . . . . . . . . . . . .2433-690-71L / R . . $189 .95 ea72 . . . . . Plymouth "B", Left / Right . . . . . . . . . . . .2433-690-72L / R . . $189 .95 ea70-74 . . Challenger, measures 14 .5" H x 34 .5" W, . . . . . . . Left / Right . . . . . . . . . . . . . . . . . . . . .2120-690-70L / R . . . $71 .45 ea72-74 . . Barracuda, measures 18" H x 36 .5" W, . . . . . . . Left / Right . . . . . . . . . . . . . . . . . . . . .2422-690-72L / R . . . $71 .45 ea
Door Jamb PillarsNew EDP coated steel panels where the striker bolt is located . These are not part of a factory quarter panel and must be purchased separately .
70-74 . . Challenger Coupe, Left / Right . . . . . . . .2120-604-701L / R . $197 .95 ea70-74 . . Barracuda Coupe, Left / Right . . . . . . . .2422-604-701L / R . $197 .95 ea70-74 . . "E" Body Inner Quarter Support to Floor Brace, . . . . . . . Left / Right . . . . . . . . . . . . . . . . . . . . .2120-604-704L / R . . $21 .95 ea68-70 . . "B" Body 2-door Hardtop (except Charger), . . . . . . . Left / Right . . . . . . . . . . . . . . . . . . . . .2132-604-683L / R . . . . $InquireNOTE: '68-70 "B"-body Door Pillars are currently under development. 71-72 . . Plymouth "B" 2-door Hardtop, Left / Right . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2433-604-711L / R . $179 .95 ea
Quarter Panel Extensions (End Caps)New die-cast extensions on the back of the quarter panel that house the tail lamps .
68 . . . . . Plymouth "B", Left / Right . . . . . . . . . . . .2432-611-681L / R . $131 .95 ea69 . . . . . Plymouth "B", Left / Right . . . . . . . . . . . .2432-611-691L / R . $131 .95 ea
Door Jamb "U"-SealsRubber seals that seal the bottom of the quarter glass in the door jamb . Sold in pairs for one car .
Quarter Panel OrnamentsNew die-cast scoops that trim the sides of the quarter panels on R/T models .
(photo not available)71 . . . . . Challenger R/T, Left / Right . . . . . . . . . .2120-616-71L / R . . . . . $InquireNOTE: These items are currently under development.
Inner Rear WheelhousesEDP coated steel panels that form the inner half of the rear wheelhouse (these are the ones seen inside the trunk) .
70-74 . . "E" Body Coupe, Left / Right . . . . . . . . .2120-670-70L / R . . $164 .95 ea68-70 . . "B" Body (except Convertible), LH / RH 2132-670-68L / R . . $164 .95 ea
71-74 . . "B" Body, Left / Right . . . . . . . . . . . . . . .2133-670-71L / R . . $164 .95 ea
Outer Rear Wheelhouses New EDP coated steel panels mate up to the quarter panel in the wheel arch . Al-ways a good idea to replace when replacing quarter panels .
70-74 . . Challenger, Left / Right . . . . . . . . . . . . .2120-675-70L / R . . $120 .95 ea70-74 . . Barracuda, Left / Right . . . . . . . . . . . . . .2422-675-70L / R . . $120 .95 ea
68-70 . . Dodge “B” Body, Left / Right . . . . . . . . .2132-675-68L / R . . $142 .95 ea68-70 . . Plymouth “B” Body, Left / Right . . . . . . .2432-675-68L / R . . $142 .95 ea
71-72 . . Plymouth "B" Body, Left / Right . . . . . . .2433-675-71L / R . . $164 .95 ea
Look!
Parts marked with this symbol are officially licensed products of Chrysler LLC.
1�
trunkTrunk Lids New EDP coated steel trunk lids are complete bolt-on assemblies, not just the outer skin . Barracuda models include provisions to mount both styles of factory rear spoil-ers, while the Challenger version does not have provisions for the rear spoiler .
Rear Spoiler Mounting BracketsThese are the steel brackets under the trunk lid that reinforce the rear spoiler mount-ing points . Used with models with a rear "GO" or "Wing" type spoiler .
Look! Deck Filler PanelsThese are the steel panels that fill between the trunk lid and rear window . Usually rusted and repairs the rear window lower channel .
Trunk Weatherstrip Gutters These EDP coated steel rails weld to the quarter panel and form the channel for the trunk weatherstrip . These are not included with a factory quarter panel, so be sure to purchase them if needed with a quarter replacement .
70-74 . . Challenger, Left / Right . . . . . . . . . . . . .2120-714-70L / R . . . $82 .45 ea70-74 . . Barracuda, Left / Right . . . . . . . . . . . . . .2422-714-70L / R . . . $82 .45 ea68-70 . . Plymouth "B" Upper, Left / Right . . . . . .2432-714-681L / R . . $82 .45 ea68-69 . . Plymouth "B" Lower, Left / Right . . . . . .2432-714-683L / R . . . . $Inquire71-74 . . Plymouth "B", Left / Right . . . . . . . . . . . .2433-714-711L / R . $109 .95 ea68-70 . . Charger, Left / Right . . . . . . . . . . . . . . . .2161-714-681L / R . . $89 .95 ea
Deck Latch Support BracesEDP coated steel brace that supports the deck lock striker .
Don’t even THINK……of replacing quarter panels while leaving old rusted outer
wheelhouses in place . Many people have made this mistake over the years, and end up having to do their car over again . The original outer wheelhouse is welded onto the quarter panel at the factory, and the seam forms a natural place to trap moisture and debris . Whenever you see a car with rust around the wheel well opening, you know that BOTH the quarter panel and the outer wheelhouse are badly rusted . While the wheelhouse is indeed hidden behind the quarter panel, it is the foundation that your new quarter panel must be welded to!
Parts marked with this symbol are officially licensed products of Chrysler LLC.
1�
Trunk Floors Complete EDP coated trunk floors cover factory seam to seam to completely re-place rusted original panels . No more splicing 2-piece panels together that don't have complete coverage! Be sure to also order floor braces, spare tire hold-down bracket, and rear cross rails if needed .
Spare Tire Hold-Down Brackets Don't forget this important little bracket that welds to the trunk floor and holds the spare tire J-bolt . Modify for convertible models .
Trunk Floor Drop-Offs These EDP coated panels fill the area from the trunk floor down to the bottom rear of the quarter panel, making the "wall" of the lower side of the trunk (behind the lower rear quarter) .
70-74 . . Challenger, Left / Right . . . . . . . . . . . . .2120-735-70L / R . . $120 .95 ea70-74 . . Barracuda, Left / Right . . . . . . . . . . . . . .2422-735-70L / R . . $120 .95 ea68-70 . . Plymouth "B" Body, Left / Right . . . . . . .2432-735-68L / R . . $120 .95 ea71-74 . . Plymouth "B" Body 2-door, Left / Right .2433-735-711L / R . $120 .95 ea
71-74 . . Plymouth "B" Body 2-door Rear Pan to Rear X-member Extension, . . . . . . . Left / Right . . . . . . . . . . . . . . . . . . . . .2433-735-712L / R . . $43 .95 ea
Trunk Floor Braces New EDP coated braces that support the trunk floor . Usually replaced when restor-ing the trunk .
70-74 . . “E” Body, Left / Right . . . . . . . . . . . . . . .2120-770-70L / R . . $399 .95 ea68-70 . . Plymouth "B" Body, Left / Right . . . . . . .2432-770-68L / R . . $399 .95 ea
Look!
Parts marked with this symbol are officially licensed products of Chrysler LLC.
1�
Rear Frame Rail BracesNew EDP coated steel braces for the rear frame rails .
70-74 . . "E" Body Rear Side Rail to Inner Sill Support, . . . . . . . Left / Right . . . . . . . . . . . . . . . . . . . . .2120-773-701L / R . . $32 .95 ea70-74 . . "E" Body Front Leaf Spring Bracket, . . . . . . . Left / Right . . . . . . . . . . . . . . . . . . . . .2120-773-702L / R . . $32 .95 ea70-74 . . "E" Body Center Floor Pan Rear Support (front spring hanger bracket) . . . . . . . Left / Right . . . . . . . . . . . . . . . . . . . . .2120-773-703L / R . . $30 .75 ea70-74 . . "E" Body Rear Frame Rail Transport Tie-Down Bracket, Left / Right . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2120-773-704L / R . . $30 .75 ea72-74 . . "E" Body Tail Pipe Tip Hanger Bracket .2120-881-702 . . . . . . $32 .95 ea
68-70 . . "B" Body Front Leaf Spring Perch, Left / Right . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2132-740-682L / R . $153 .95 ea68-70 . . "B" Body Rear Leaf Spring Perch, . . . . . . . 3-piece Assembly, Left / Right . . . . . .2432-770-68LS / RS $119 .95 ea
Rear Cross RailsNew EDP coated rear cross rail that the rear valance brackets bolt to . These are commonly rusted on almost every car . Good item to replace!
Parts marked with this symbol are officially licensed products of Chrysler LLC.
1�
gas tanksReplace that rusty, muck-filled old gas tank in your Dodge or
Plymouth, with brand new high quality reproduction steel Gas Tanks from Goodmark® . There is no cost-efficient way to properly restore the outside appearance of a gas tank, and the rust particles, sludge, and stale gas residue inside are just carburetor problems waiting to happen . While you’re at it, be sure to replace rusted or weakened old straps, brackets, bolts, gas caps, and sending units . Go for it .
Gas Tank Straps New tank straps used on popular models . Early models usually use one strap, while later models use a pair of straps .
Gas TanksNew Niterne steel tanks replace rusty or leaking factory tanks with OE appearance . All tanks are made in North America . Be sure to order new straps and hardware if necessary .
Gas CapsFactory style gas caps replace missing or incorrect models and are a real comple-ment for a new restored tank . Made by an original OE supplier .
Gas Tank Sending UnitsReplacement gas tank sending units for our tanks . Be sure to order the correct application for your vehicle . Each sending unit includes seal and filter .
sIde marker lenses Side Marker LensesBrand new injection molded plastic lens assembly .
69 . . . . . All models Marker Set (4 pieces) . . . . . .2111-905-69S . . . . . . $76 .95 set
70-71 . . Challenger Side Marker Set . . . . . . . . . .2120-905-70S . . . . . $549 .95 set . . . . . . . Front Marker, Left / Right . . . . . . . . .2120-140-701L / R . $164 .95 ea . . . . . . . Rear Marker, Left / Right . . . . . . . . . .2120-625-70L / R . . $164 .95 ea . . . . . . . Marker Gasket Set (4 pieces) . . . . . .2120-142-70S . . . . . . . .$7 .65 kit
72-78 . . All models Front Marker (use 2) . . . . . . .2112-140-72 . . . . . . . $14 .25 ea
weatherstrIPsWeatherstrip KitsA convenient way to get all your weatherstrip needs in one package . See listings for specific lists of what's included in each kit .
What’s that black coating on most Goodmark® sheetmetal? It’s called EDP, which stands for Electro Deposit Primer, and it makes an
excellent primer under your paint job . As you probably know, factory paint back in the ’60’s and ’70’s was usually
just sprayed onto the surfaces that could be reached by a spray gun . But this left many blind areas behind braces, etc, completely bare of any paint protection . Hence, many cars rusted within a few years . But EDP coating is applied electrically, almost like a plating process . The excellent rust-resistant coating reaches every nook and cranny, for unparalleled corrosion resistance .
The only surface preparation required is a light scuffing of the surface for better paint adhesion . No stripping is necessary . The panel is protected from rust as long as the EDP coating remains under your paint .
This is one more way that Goodmark® goes the extra mile for our customers!
Parts marked with this symbol are officially licensed products of Chrysler LLC.
Vent Window WeatherstripsNew weatherstripping to replace the weatherstrips in the door vent glass . This is not included in our weatherstripping kit and must be purchased separately .
(photo not available)68-70 . . "B" Body 2-door Sedan / Hardtop . . . . . . . Left / Right pair . . . . . . . . . . . . . . . . .2132-418-682P . . . . . $153 .95 pr
Parts marked with this symbol are officially licensed products of Chrysler LLC.
�0
Door Opening WeatherstripsNew rubber weatherstrips that seal the door shell to the body . Sold in pairs for one car .
InterIor ComPonents Mopar Logo Rubber Accessory Floor Mats New rubber floor mats are identical to factory accessory mats and include an in-struction sheet telling where to trim for specific options . These are correct Mopar Licensed parts!
Dash PartsMolded plastic black standard steering wheel, rubber glovebox door bumpers, and instrument bezel applique kit designed to restore dash components . We also offer new switches to replace broken originals .
shoCk aBsorBersHeavy Duty Shock AbsorbersReproduction of the factory heavy-duty shocks that were optional on all high perfor-mance Mopars . OE appearance make these a great upgrade to a restored car .