Huawei HCDA Fast Track training (SU0-211)

Huawei HCDA Fast Track training (SU0-211)

Number: SU0-211Passing Score: 800Time Limit: 120 minFile Version: 2012-03-16

http://www.gratisexam.com/

Huawei HCDA Fast-track (Exam: SU0-211)

Exam A

QUESTION 1IP address 199.32.59.64, subnet mask is 255.255.255.224, subnet address

A. 199.32.59.64B. 199.32.59.65C. 199.32.59.192D. 199.32.59.224

Correct Answer: ASection: (none)Explanation

Explanation/Reference:

QUESTION 2Huawei router serial interface encapsulation PPP protocol, you need to enter the command interface view is

A. link-protocol pppB. encapsulation pppC. enable pppD. address ppp



QUESTION 3Divided by the network topology, network can be divided into

A. BusB. StarC. TreeD. RingE. grid

Correct Answer: ABCDESection: (none)Explanation


QUESTION 4Among which the following network security and confidentiality of poor

A. meshB. treeC. busD. star3

Correct Answer: CSection: (none)Explanation


QUESTION 5ADSL Modem with phone line interface is connected to

A. RJ 11B. RJ 45C. IEEE 1394D. S / V terminal



QUESTION 6VDSL technology is applicable to ().

A. long-range (greater than 2Km, less than 5Km) dispersed customer baseB. medium distance (less than 1.5Km), more focused customer baseC. close (less than 200M)-intensive customer baseD. long-distance (greater than 15Km) a concentrated customer base



QUESTION 7Which of the following are transport layer protocol?

A. IPB. TCPC. UDPD. SNMP

Correct Answer: BCSection: (none)Explanation


QUESTION 8In the OSI model, the transport layer for the first () level


A. 3B. 4C. 6D. 7

Correct Answer: BSection: (none)Explanation


QUESTION 9Which of the following protocol is the data link layer protocol ()

A. PPPB. HDLCC. IPXD. IEEE 802.3

Correct Answer: ABDSection: (none)Explanation


QUESTION 10Have their own reliability mechanism for application layer protocol, () applies as transport layer protocol.

A. TCPB. UDPC. ICMPD. HDLC



QUESTION 11TCP applications will assign a source port number. TCP packet header source port number in the occupied ()bytes.

A. 1B. 2C. 4D. 8



QUESTION 12The following agreements which are described in presentation layer OSI reference model protocol

A. ASCII, EB, C, DICB. IP, ARPC. MAC, LLCD. MPEG, MIDIE. RPC, NFS, SQLF. PICT, MPEG

Correct Answer: ADFSection: (none)Explanation


QUESTION 13ICMP packet type field is 8, the code field is zero, on behalf of ICMP ().

A. Echo request packetB. Echo response packetC. exceeded packetsD. destination unreachable message



QUESTION 14V.35 synchronous mode the maximum transmission rate is

A. 64KbpsB. 9200bpsC. 56kbpsD. 2048kbps

Correct Answer: DSection: (none)

Explanation


QUESTION 15VLSM is the meaning of

A. Variable Length Subnet MaskingB. Variable Length Shortest MaskingC. Very Long / Shortest MaskingD. Variable Long Subnet Masking



QUESTION 16IP address 192.168.1.7/28 to subnet mask ()

A. 255.255.255.240B. 255.255.255.248C. 255.255.255.224D. 255.255.255.252



QUESTION 17D class IP address with the default subnet mask () bits

A. 8B. 16C. 24D. No mask

Correct Answer: DSection: (none)Explanation


QUESTION 18The following () is a valid IP host address

A. 127.2.3.5B. 1.255.255.2/24

C. 225.23.200.9D. 192.240.150.255/24



QUESTION 19FTP is designed for () the file transfer.

A. Low RateB. High-throughputC. simpleD. read-only memory



QUESTION 20TFTP protocol is a simple file transfer protocol, which uses () for file transfer

A. SIPB. UDPC. TCPD. RTP



QUESTION 21In the DNS query, the message is commonly used

A. SIPB. RTPC. UDPD. TCP



QUESTION 22Has a MAC address () bits

A. 6B. 12C. 24D. 48



QUESTION 23Through an Ethernet Hub is the essence of the formation ().

A. Star EthernetB. shared EthernetC. Switched EthernetD. Token Ring Ethernet



QUESTION 24L2 switch in the case of multicast, and unicast the same, MAC address entries is set up to learn to get throughthe MAC.

A. TrueB. False



QUESTION 25Brings the advantage of port aggregation ()

A. Increased link bandwidthB. for traffic load sharingC. increase network reliabilityD. easy to copy the data for analysis

Correct Answer: ABCSection: (none)Explanation


QUESTION 26Layer 2 network easily lead to network loop path following problem ().

A. increase the link bandwidthB. Broadcast StormC. MAC address table instabilityD. port cannot be aggregated



QUESTION 27Hired STP Layer 2 switching network, the port which the state may experience the following

A. DisabledB. BlockingC. ListeningD. LearningE. Forwarding



QUESTION 28In making the MSTP, the bridge with the following conditions are the same MSTP domain ().

A. At the same time on the root protectionB. have the same domain nameC. The number of ports in forwarding state lineD. VLAN instance mapping and consistency

Correct Answer: BDSection: (none)Explanation


QUESTION 29GVRP is () stands

A. GARP VLAN Registration ProtocolB. GARP VLAN Record Protocol

C. GARP VLAN Remark ProtocolD. GARP VLAN Rewrite Protocol



QUESTION 30The switch access port ethernet0 / 1 by adding VLAN 4, can be configured as follows ().

A. [Switch] vlan 4[Switch-vlan4] port ethernet 0 / 1

B. [Switch] vlan 4[Switch-Ethernet0 / 1] port access vlan 4

C. [Switch] vlan 4[Switch-vlan4] port access ethernet 0 / 1

D. [Switch] vlan 4[Switch-Ethernet0 / 1] port access vlan pvid 4

Correct Answer: ABSection: (none)Explanation


QUESTION 31Access is generally the type of port on the switch port for connecting a computer, the following statements iscorrect ().

A. received packets with a tag, and discardedB. Access port it in the default VLAN is VLAN, do not need to manually configure the Access default VLAN on

the portC. Access ports can only belong to a VLAND. untag received packets marked with the port's PVID information

Correct Answer: ABCDSection: (none)Explanation


QUESTION 32The following are ways to achieve inter-VLAN communication

A. STPB. GVRPC. L2 Switch + RouterD. L3 Switch

Correct Answer: CD

Section: (none)Explanation



QUESTION 33three-switch three hosts connected users, respectively, A, B, C, A and B which requires the user to exchangethe second floor, A, B and C Layer 2 isolation, A, B and C can communicate at Layer 3, will have to switchWhat do the following configuration

A. A and B draw users to the same VLANB. C user program to another with a different VLAN A, BC. A, B User host address must be on the same network segmentD. two VLAN configured on the switch virtual interface and configure the IP address of the user'sdefault

gateway address as



QUESTION 34A complete data communication system consists of several parts which

A. SenderB. ReceiverC. mediaD. messageE. Agreement



QUESTION 35In which of the following network topology, each with redundant links between two nodes

A. meshB. starC. treeD. busE. ring

Correct Answer: AESection: (none)Explanation


QUESTION 36Judge: Data format of the data communication needs of the creator and receiver of information to reach aconsensus in advance.

A. TrueB. False



QUESTION 37The main feature of the LAN: the network is owned by a unit, and the geographical scope and the number ofsites are limited. Common LAN transmission medium with ().

A. FiberB. Coaxial cableC. Twisted pairD. ADSL



QUESTION 38Half-duplex data communication mode (half-duplex mode), the each device can send and receive, but not bothsimultaneously. When a device is sent, the other can only receive, and vice versa.The following are working in half-duplex mode ().

A. KeyboardB. DisplayC. RadioD. telephone network



QUESTION 39

From the communications division of both the way information exchange, can have the followingcommunication ().

A. simplexB. Half-duplexC. duplexD. auto-negotiation



QUESTION 40Larger geographical area network connection, in large areas to provide data communications services, primarilyfor LAN interconnection network is ().

A. Large LANB. WANC. MAND. Backbone



QUESTION 41To determine: the more commonly used local area network bus, star topology is the actual physical deviceconfiguration, rather than the network's logical structure.

A. TrueB. False



QUESTION 42When a node in the network to transmit data on the media, the data will be transmitted to all nodes. Thisnetwork topology is ().

A. StarB. BusC. TreeD. Ring

Correct Answer: B



QUESTION 43Topology has a central control point, easy to design and installation, network media directly from a central hubor switch connected to a workstation at the region. Disadvantage is that once the central point of controlequipment problems, prone to single point of failure.This topology is commonly used local area network ().

A. StarB. BusC. TreeD. Ring



QUESTION 44As the end systems and communication systems signal conversion equipment, modem (Modem) is essentialfor wide-area network devices in one. Modem and router connected to the serial port is divided into () two.

A. SynchronizationB. AsynchronousC. SwitchingD. routed



QUESTION 45Message from a sender to a receiver through a physical channel between thecalled

A. AgreementB. SignalC. mediaD. Equipment



QUESTION 46

IEEE LAN standards are mainly defined 802.X protocol suite, including wireless LAN (WLAN) standard ().

A. 802.3B. 802.4C. 802.5D. 802.11



QUESTION 47OSIreference model for computer network to build an easy to understand, clear hierarchical model. OSIreference model () standards organization.

A. ISOB. IEEEC. ITUD. IETF



QUESTION 48U.S. National Bureau of Standards (American National Standards Institute) ANSI is a corporate, governmentand other organizations, members of voluntary organizations that define the () is standard.

A. 802.3B. RFCC. FDDID. VPN



QUESTION 49Two devices can send or receive data, but not both simultaneously. This work is


Correct Answer: B



QUESTION 50The following topology, the reliability of the highest

A. BusB. StarC. RingD. grid



QUESTION 51According to the geographicalscope of coverage, the network can be divided into

A. CampusB. LANC. WAND. Enterprise Network



QUESTION 52RFC (Request for Comments) is a standards organization which generated the following

A. IEEEB. ITU-TC. IETFD. ISO



QUESTION 53Which of the following standards organizations to develop the most relevant local area network protocol, suchas the 802 series of protocols

A. IEEE

B. ITU-TC. IETFD. ETSI



QUESTION 54In which the network topology, a link failure will cause all traffic disruption

A. MeshB. BusC. StarD. Tree



QUESTION 55Keyboard can be used to input, the keyboard work is




QUESTION 56Funded by the U.S. Department of Defense established a called ARPANET (the ARPANET is) based on ()network, ARPANET was the first prototype of today's Internet.

A. Low-speed serial connectionB. Circuit SwitchedC. Packet switchingD. MPLS forwarding



QUESTION 57Is a router for network interconnection of computer equipment, it works in the OSI reference model ().

A. Session layerB. Data Link LayerC. Network LayerD. Application layer



QUESTION 58Single shared bus, all devices share a data bus port, the same time only one user to transmit data. Thefollowing equipment belonging to a single bus is shared ().

A. hubB. SwitchC. RouterD. ATM switch



QUESTION 59The following is part of wide area network ().

A. ChinaPublic Packet Switched Network (CHINAPAC)B. Chinese public digital data network (CHINADDN)C. National Education and Research Network (CERnet)D. CNGI (China Next Generation Internet)



QUESTION 60IETF standards bodies produce two documents, RFC, and ().

A. Internet DraftB. IEEE standardC. Electrical CharacteristicsD. Physical Layer Standard



QUESTION 61Description of network structure is correct

A. fully connected grid network, the n (n-1) / 2 n physical linksto connect devicesB. All grid-connected network, if one link fails, it will not affect the whole systemC. fully connected network robustness is betterD. network topology drawback is high cost and difficult to implement



QUESTION 62LAN features, it is not true that

A. high transmission efficiency, better reliabilityB. simple structure, easy constructionC. layout flexibility for easy expansionD. Covering a wide range of D.



QUESTION 63Ordinary users generally through ISP (Internet Service Provider) services provided to connect to the Internet.ISP can be divided into

A. International Service ProvidersB. National Service ProviderC. Regional Internet Service ProviderD. local Internet service provider



QUESTION 64In the network protocol to provide both data and control information communication structure and

format of this part is

A. SyntaxB. Semantic partC. Timing sectionD. rules section



QUESTION 65The typical structure of IP telecom networks can be divided into

A. BackboneB. tandem networkC. MAND. Access Network

Correct Answer: ACDSection: (none)Explanation


QUESTION 66Networks are usually divided into three types: LAN, MAN and WAN. Attributable to a specific network dependson which type ().

A. size of the networkB. OwnerC. coverageD. Physical Architecture



QUESTION 67A complete IP network is divided into ().

A. BackboneB. MANC. Access NetworkD. Mobile Network

Correct Answer: ABCSection: (none)

Explanation


QUESTION 68Backbone structures can be roughly divided into

A. Fully connected network structureB. flat hierarchyC. Flat + space hierarchyD. dual ownership structure



QUESTION 69MAN in the middle of the backbone network and access network, and can be divided into

A. bearing layerB. Core layerC. Tandem layerD. Access Layer

Correct Answer: BCDSection: (none)Explanation


QUESTION 70As the backbone is the core of the network, the backbone of the requirements

A. High-ReliabilityB. Flexibility and scalabilityC. flatD. QOS rational planningE. operable Management



QUESTION 71A complete IP network service access network control points are below the floor ().

A. Backbone

B. MANC. Access NetworkD. Core



QUESTION 72In the Internet access business in the widespread use of ADSL and () two technologies. Both technologiessupport both dial-up access and leased line access two access methods.

A. LANB. WANC. MSTPD. Metro



QUESTION 73VPN can be divided according to achieve the level ().

A. L2VPNB. L3VPNC. VPDND. GRE VPN



QUESTION 74End-user access to the Internet process, the following statements is correct ().

A. Internet users initiate requests, access network equipment for the userto establish two-story two-story upperconnection and the request is passed through the BRAS device

B. BRAS is responsible for user authentication, authorization and IP addresses assigned to usersC. After successful user authentication the BRAS user packet that is routed to the upstream device

convergence layer device, the convergence layer device to complete the route forwarding, a user canaccess the external network

D. access network control of user information, plus strategies for the filtered user information forwarded to theupper device

Correct Answer: ABC



QUESTION 75BGP MPLS VPN model to handle basic MPLS forwarding. The device does not maintain VPN information is ().

A. PB. PEC. C, ED. MCE



QUESTION 76When the backbone network using plane + space hierarchical structure, the following statements is correct ().

A. In a plane fails, another cannot back up planeB. different planes generally carry different businessC. under normal circumstances, the business between the twoplanes will not affect each otherD. hierarchy is relatively flat + flat hierarchy and high reliability space



QUESTION 77The following is a correct description of ADSL

A. asymmetric uplink and downlink transmission speed of DSL technologyB. downlink transmission rate symmetric DSL technologyC. uplink downlink rate can be larger than the rateD. downlink rate than upstream rate can be large

Correct Answer: ADSection: (none)Explanation


QUESTION 78VDSL representatives in the V ().

A. Variable-length

B. Video-on-demandC. Very-high-bit-rateD. V-sign



QUESTION 79ADSL, VDSL can be used as the encoding ().

A. CAPB. DMTC. DWMTD. SLC



QUESTION 80ADSL to G. Lite (that is, G.992.2) standard by the () standard adopted by the Organization.

A. IEEEB. ITUC. MEFD. ANSI



QUESTION 81ADSL Modem connected to a computer with the user interface is

A. RJ 11B. RJ 45C. IEEE 1394D. S / V terminal



QUESTION 82VDSL asymmetrical data transmission in support of the highest transfer rate is

A. 26MbpsB. 52MbpsC. 42MbpsD. 13Mbps



QUESTION 83VDSL support symmetric data transmission rate is the highest

A. 26MbpsB. 52MbpsC. 42MbpsD. 13Mbps



QUESTION 84Which of the following operating systems support for PPPoE dial-up client by default?

A. Windows 95B. windows 98C. windows 2000D. windows xp



QUESTION 85In the cable broadband access solutions, users at home use () to access the broadband network

A. ADSL MODEMB. VDSL MODEMC. SHDSL MODEMD. CA, BLE MODEM

Correct Answer: D



QUESTION 86ADSL is a broadband access technology, the following () method refers to broadband ADSL.

A. Super Smart CallB. residential broadbandC. Network ExpressD. wired through

Correct Answer: ACSection: (none)Explanation


QUESTION 87The following statement on the right is ADSL ().

A. ADSL enables high-speed digital information and telephone information in a different telephone lines forsimultaneous transmission on the frequency

B. ADSL broadband access to users while maintaining the user's telephone service and the quality of theoriginal unchanged

C. ADSL broadband telephone services with users in business processes, the two are separateD. ADSL technology enables high-speed digital information andtelephone information in the telephone line

transmission sub-periods on the same frequency band



QUESTION 88ADSL downstream speeds of up to

A. 1.5MbpsB. 2MbpsC. 6mbpsD. 8Mpbs



QUESTION 89ADSL data transmission for the uplink in the band is

A. 26 KHZ ~ 138 KHZB. 26 KHZ ~ 69 KHZC. 26 KHZ ~ 1104 KHZD. 26 KHZ ~ 256 KHZ



QUESTION 90ADSL used for downlink data transmission frequency band is

A. 26KHZ ~ 138KHZB. 138 KHZ ~ 1104 KHZC. 26 KHZ ~ 1104 KHZD. 138 KHZ ~ 2200 KHZ



QUESTION 91Days off saying VDSL is the correct

A. VDSL only supports symmetric transmissionB. VDSL supports only non-symmetric transmissionC. VDSL supports both symmetric and asymmetric transmissionD. VDSL can only transmit a fixed rate



QUESTION 92Theoretically, ADSL2 upstream rate can reach a maximum ().

A. 512KbpsB. 1MbpsC. 8MbpsD. 100Mbps



QUESTION 93Theoretically, VDSL2 can reach a maximum downstream rate ().

A. 512KbpsB. 1MbpsC. 8MbpsD. 100Mbps



QUESTION 94The following xDSL technology, the fastest data transfer rate is ().

A. HDSLB. SDSLC. VDSLD. ADSL



QUESTION 95ADSL, there are two channels work, they are

A. FastB. serialtransmissionC. Fourier TransformD. intertwinedE. parallel transmission



QUESTION 96ADSL Modem if the computer is directly connected to the computer through PPPoE dial-up, usually in this case,ADSL Modem () operation

A. Route modeB. Bridge mode

C. IPOA modeD. MPOA model



QUESTION 97ADSL technology is applicable to ().

A. long-range (greater than 2Km, less than 5Km) dispersed customer baseB. medium distance (less than 1.5Km), more focused customer baseC. close (less than 200M)-intensive customer baseD. long-distance (greater than 15Km) a concentrated customer base



QUESTION 98OSI reference model that is

A. Organization Standard InstituteB. Organization Standard InterconnectionC. Open SystemInternetD. Open System Interconnection



QUESTION 99The data link layer includes two sub-layers, namely,

A. PVC sublayerB. MAC sublayerC. LLC sublayerD. VC sublayer



QUESTION 100Which of the following equipment is working in the data link layer?

A. HubB. BridgeC. switchD. RouterE. Firewall



QUESTION 101Is the broadcast MAC address

A. FF-FF-FF-FFB. FF-FF-FF-FF-FF-FFC. 00-00-00-00-00-00D. 00-00-00-FF-FF-FF



QUESTION 102In the IEEE 802 system described in Logical Link Control protocol (LLC) sublayer functions, features andprotocols is

A. IEEE 802.2B. IEEE 802.3C. IEEE 802.4D. IEEE 802.5



QUESTION 103Which of the following is associated with the WAN data link layer protocol?

A. EthernetB. PPPC. HDLCD. UDP

E. SMTP




QUESTION 104Routers work in the OSI Reference Model

A. Physical LayerB. Data Link LayerC. Network LayerD. Application layer



QUESTION 105Which of the following error messages can provide information and handling of IP packets to the source?

A. TCPB. UDPC. ICMPD. IGMP



QUESTION 106The data in the network layer, we call

A. SectionB. PackageC. BitD. Frame

Correct Answer: B



QUESTION 107In the OSI model, the network layer functions is the right description

A. ensure that the correct transmission of dataB. How to determine packet forwarding and routingC. The channel transmission bit streamD. correction and flow control



QUESTION 108ARP protocol is the role of

A. will be mapped to the IP address port numberB. Access to the second layer address corresponding to the IP addressC. Broadcast IP addressD. Obtain an IP address corresponding to the second floor of address



QUESTION 109OSI reference model of the network is divided into () layer

A. 3B. 5C. 6D. 7



QUESTION 110RARP is the role of

A. IP address will be converted to their own MAC address

B. the other's IP addresses to MACaddressesC. will be converted into each other's IP address MAC addressD. know their own MAC address, RARP protocol to get through their own IP address



QUESTION 111IP protocol is characterized by

A. reliable, connectionless-orientedB. unreliable, connectionless-orientedC. , reliable, connection-orientedD. unreliable, connection-oriented



QUESTION 112General network address from which several parts

A. logical addressB. Link AddressC. Network AddressD. Host Address

Correct Answer: CDSection: (none)Explanation


QUESTION 113Which of the following protocol provides a connection-oriented transport service?

A. IPB. IPXC. TCPD. UDP



QUESTION 114Multiplexer means multiple applications share the same transport layer connection established for datatransmission, the transport layer is what is to distinguish between different applications

A. DSAPB. SSAPC. Agreement No.D. port



QUESTION 115DNS port number is

A. 21B. 23C. 53D. 80



QUESTION 116correctly describes the process of data encapsulation is

A. Data section -> packet -> data frame -> data stream -> DataB. Data Flow -> data section -> packet -> data frame -> dataC. Data -> packet -> data section -> data frame -> data streamD. Data -> Data section -> packet -> data frame -> data stream



QUESTION 117What is the session layer function?

A. Provide encryption / decryptionB. to provide data format conversion andC. establish a connection between the different hostD. establish, maintain and terminate sessions



QUESTION 118TCP / IP protocol level is not divided according to the OSI reference model, corresponding to the OSI sevenlayer network model, is not defined

A. link layer and network layerB. network layer andtransport layerC. Session layer and presentation layerD. transport layer and session layer



QUESTION 119When the packet is passed from the top to the lower, the head will be

A. AddB. PeelC. ReorderingD. Modify



QUESTION 120RPC, NFS, SQL these agreements work in the OSI reference model

A. Network LayerB. Transport LayerC. Session layerD. Presentation Layer



QUESTION 121In the OSI reference model, the following items that the presentation layer functions

A. Data EncryptionB. Data CompressionC. Session ControlD. Data format conversion



QUESTION 122OSI reference model layer to the first () layer is called the underlying (Lower layer), responsible for datatransmission in the network.

A. IIB. IIIC. fourD. five



QUESTION 123Network-connected devices are often located under the OSI reference model () layer, the hardware andsoftware combination to achieve.




QUESTION 124OSI reference model () layer 4-7 as senior (Upper layer), also known as the host layer.




QUESTION 125Level (Upper layer) for the right to protect data transfer, to () method to achieve.

A. HardwareB. SoftwareC. combination of hardware and softwareD. Software or hardware



QUESTION 126OSI Reference Model () function is to create a host-end connections, to provide data transmission and re-passbefore the error detection.

A. Data Link LayerB. Physical LayerC. Network LayerD. Transport Layer



QUESTION 127OSI Reference Model () function is to provide for the application layer data encoding and conversion functions,process the data format, data encryption.

A. Presentation LayerB. session layerC. Network LayerD. Application layer



QUESTION 128OSI Reference Model () function is the combination of bits into bytes, then the combination of framing bytes toprovide media access and so on.

A. DataLink Layer

B. session layerC. Network LayerD. Application layer



QUESTION 129OSI Reference Model () function is in the bit stream transmitted between devices.

A. Data Link LayerB. Physical LayerC. Network LayerD. Application layer



QUESTION 130OSI Reference Model () from the different devices to communicate between applications in a service requestand response form.

A. Data Link LayerB. session layerC. Network LayerD. Application layer



QUESTION 131OSI reference model provides network services through the application process, providing interapplicationcommunication is ().

A. Data Link LayerB. session layerC. Network LayerD. Application layer



QUESTION 132Similar to the OSI model, TCP / IP model uses the same hierarchical structure. TCP / IP model is divided into ()a level.

A. fourB. fiveC. sixD. seven



QUESTION 133TCP / IP model and OSI reference model, the difference is that TCP / IP to the OSI model () are included in theapplication layer.

A. transport layer, presentation layerB. session layer, presentation layerC. transport layer, session layerD. presentation layer, application layer



QUESTION 134TCP/IP model layer using the PDU (protocol data unit) to exchange information with the TCP transport layerheader of the PDU is called ().

A. FrameB. PackageC. SectionD. binary bit stream



QUESTION 135TCP / IP model () specification data transfer rate, maximum transmission distance.

A. Physical Layer

B. Data Link LayerC. Transport LayerD. Application layer



QUESTION 136WAN G.703 standards are related to () standard.

A. Physical LayerB. Data Link LayerC. Transport LayerD. Application layer



QUESTION 137Repeater work in TCP / IP model ().




QUESTION 138Coaxial cable can be classified according to their diameter, () for relatively large local network, its standard longdistance and high reliability.

A. thick coaxial cableB. thin coaxial cableC. 10 Coaxial CableD. 16 Coaxial Cable



QUESTION 139By shielding layers of glass fiber and, without the interference of electromagnetic signals, the transmission rate,transmission distance is long. But expensive. This is a physical medium ().

A. CoaxialB. twisted pairC. fiberD. waveguide fiber



QUESTION 140In the OSI reference model, the bottom is ()

A. Data Link LayerB. Application LayerC. Physical layerD. Network Layer



QUESTION 141The data link layer () is responsible for identifying the protocol type and data package, and has a PDUsequence control, error control, flow control and other functions.

A. PVC sublayerB. MAC sublayerC. LLC sublayerD. VC sublayer



QUESTION 142The following protocols are commonly used WAN data link layer protocol is ().

A. 802.2B. 802.4C. HDLC

D. PPP



QUESTION 143In the OSI reference model, which defines the level of data transfer needed to achieve the mechanical,electrical, functional characteristics and processes and other means?

A. Transport LayerB. Data Link LayerC. Network LayerD. Physical Layer



QUESTION 144Is the physical layer transmission

A. FrameB. PackageC. SectionD. binary bit stream



QUESTION 145The data link layer protocol used for the protocol data unit

A. binary bit streamB. FrameC. PackageD. Section.



QUESTION 146

In which layer of the OSI model are high, also known as the host layer, responsible for data transfer betweenthe host and user interface to

A. Data Link LayerB. network layerC. Transport LayerD. session layerE. Presentation LayerF. Application layer

Correct Answer: DEFSection: (none)Explanation


QUESTION 147Which layer is responsible for coordinating both send and receive data rates, namely, flow control to preventbuffer overflow and the line blocked?

A. Application LayerB. Data Link LayerC. NetworkLayerD. Physical Layer



QUESTION 148Responsible for the unreliable transmission channel into a reliable transmission channel, to transmit any dataframe checksum, error control and frame the use of sequential control functions which layer?

A. Physical LayerB. Data Link LayerC. Network LayerD. Transport Layer



QUESTION 149At present, the most widely used LAN standard is based on () Ethernet standard

A. IEEE 802.5B. IEEE 802.2C. IEEE 802.3

D. IEEE 802.1



QUESTION 150Which of the following is the data link layer functionality?

A. define the physical addressB. Network topologyC. RoutingD. Physical media accessE. test error

Correct Answer: ABDESection: (none)Explanation


QUESTION 151In the VRP platform, direct routing, static routing, RIP, OSPF default route by descending priority order iscorrect

A. Direct routing, static routing, RIP, OSPFB. Direct routing, OSPF, static routing, RIPC. direct routing, OSPF, RIP, static routingD. direct routing, RIP, static routing, OSPF



QUESTION 152Which of the following routing protocols are available?

A. IPB. OSPFC. BGPD. IPX



QUESTION 153UDP is a connectionless-oriented must use () to provide reliability

A. Internet ProtocolB. Applicationlayer protocolC. Network layer protocolD. Transmission Control



QUESTION 154In the OSI reference model, to complete end to end error detection and flow control is




QUESTION 155Transport layer which functions

A. upper segment dataB. Establishment of end to end connectionC. Data from one host to another host thatD. ensure that the data sequence, reliable and correct transmissionE. Addressing



QUESTION 156In the OSI seven layer model, when the data receiver cannot handle more data, which issued a stop layer ofinformation to the sender

A. Physical LayerB. Transport LayerC. Session layerD. Presentation Layer



QUESTION 157In the OSI reference model, from the bottom to the top of the order is correct

A. physical layer, data link layer, network layer, transport layer, session layer, presentation layer, applicationlayer

B. physical layer, data link layer,network layer, transport layer, presentation layer, session layer, applicationlayer

C. physical layer, transport layer, data link layer, network layer, presentation layer, session layer, applicationlayer

D. physical layer, data link layer, transport layer, presentation layer, network layer, session layer, applicationlayer



QUESTION 158MAC address from the 48 binary digits, usually expressed as hexadecimal numbers. Which the first ()-digithexadecimal number assigned by the IEEE uniform equipment manufacturers.

A. 4B. 5C. 6D. 7



QUESTION 159Is a management agreement and provide information services for IP, the protocol message carries the IPpacket's network layer protocol ().

A. ARPB. IPC. ICMPD. 802.2



QUESTION 160Hardware address is cured in (), such as MAC address, the device used to communicate with each other on thesame link.

A. PICB. NICC. POWERD. FAN



QUESTION 161SNMP, Radius, etc. pay more attention to the transmission efficiency of the application will choose () as thetransport layer protocol.

A. TCPB. UDPC. ICMPD. HDLC



QUESTION 162Defines the standard data representation and complete data encryption, decryption, compression,decompression function is the TCP / IP model () to complete.

A. Data Link LayerB. network layerC. Transport LayerD. Application layer



QUESTION 163Based on TCP as the transport protocol () protocol to provide the domain name to IP address translation,allowing for decentralized management of domain resources.

A. TCP

B. UDPC. DNSD. HTTP



QUESTION 164() protocol for the transmission of those pages on the World Wide Web documents.

A. TCPB. UDPC. DNSD. HTTP



QUESTION 165TCP / IP model, used to send and receive mail for the protocol ().

A. SMTPB. POP 3C. DNSD. HTTP



QUESTION 166() dial-up access to remote access user authentication protocol to complete the authentication, authorizationand accounting functions.

A. SMTPB. RADIUSC. DNSD. HTTP



QUESTION 167Which of the following devices work in the physical layer?

A. SwitchB. HubC. RouterD. Firewall



QUESTION 168Which of the following agreement is the physical layer protocol?

A. RS -232B. RJ 45C. FDDID. V.35



QUESTION 169Which of the following is the physical layer transmission media?

A. FiberB. twisted pairC. Radio wavesD. Ethernet



QUESTION 170Which of the following is associated with local area network standard physical layer cable?

A. 100Base-TB. 10Base5C. 100Base-FXD. 1000Base-SX/LX



QUESTION 171Which is a common WAN INTERFACES?

A. V.35 InterfaceB. ATM InterfaceC. EthernetInterfaceD. FR Interface



QUESTION 172Common DCE equipment

A. end hostsB. WAN switchC. RouterD. ModemE. CSU / DSU (Channel Service Unit / Data Service Unit)

Correct Answer: BDESection: (none)Explanation


QUESTION 173Below () interface for the physical interface

A. dialer interfaceB. Voice InterfaceC. Serial PortD. sub-interfaceE. C, E 1/PRI InterfaceF. Virtual interface templateG. ISDN BRI Interface

Correct Answer: BCEGSection: (none)Explanation


QUESTION 174OSI reference model merits

A. complex network into simplecomponentsB. module allows engineers to focus on the design and development functionsC. define the standard interface, the interactive multi-factoryD. the complex network problem into small, simple problem, easy to learn and operate



QUESTION 175In the TCP / IP reference model, which is running in application layer protocol over TCP’S?

A. HTTPB. TFTPC. FTPD. SMTPE. SNMP



QUESTION 176TCP packet header up to 60 bytes, if no Option field, TCP packet header length () bytes.

A. 8B. 20C. 30D. 40



QUESTION 177TCP's error control and flow control, the following statements is correct is.

A. sender by the receiver to adjust the sending flowB. Notice the receiving end through the window flowcontrol mechanismC. Notice the small window to reduce the receiver flowD. Increase the receiver notices the small window flow



QUESTION 178Which of the following fields in the TCP header contains the field ().

A. Source PortB. Destination PortC. Sequence NumberD. Ack Num



QUESTION 179Ethernet maximum transmission unit (MTU) is the range ().

A. 64? 518B. 60? 518C. 64? 480D. 60? 480



QUESTION 180IP header contains 8bit type of service (TOS, Type of Service) field, the following included in the TOS field is ().

A. 3bit COS fieldB. 1bit minimum delayC. 1bit maximum throughputD. 1bit the highest reliability



QUESTION 181IP header TTL field of the packet can go through the number of routers. Once through a router, TTL value isdecreased by 1, when the field value (), the data packet will be discarded.

A. 0B. 1C. -1D. 2



QUESTION 182Fragmentation can occur in the original sending host, but also can occur in the middle of the router. To an IPdatagram fragmentation after in () to re-assemble.

A. packet loopbackB. the next routerC. intermediate routersD. packet destination



QUESTION 183Has been fragmented datagram may be fragmented again. Included in the IP header () for the fragmentationand re-assembled to provide enough information.

A. Type of ServiceB. FlagC. Fragment OffsetD. header checksum



QUESTION 184Which of the following equipment to achieve all levels of the OSI reference model function?

A. routerB. Email ServersC. Three switchesD. network management server



QUESTION 185The following statement is correct about the TCP connection is established ().

A. TCP connection isestablished to conduct 3-way handshakeB. 3 times a handshake packet can solve the problem of delayedC. 3 way handshake mechanism to help assure the reliability of the data exchangeD. 3-way handshake mechanism cannot guarantee the security of dataexchange



QUESTION 186TCP / IP protocol stack is packet decapsulation () followed by detachment layers of header information.

A. from top to bottomB. From the bottomC. From the transport layer to the nextD. From the first networklayer



QUESTION 187IP address is the only public address, and () can be reused in the LAN.

A. Host AddressB. Private AddressC. Network AddressD. subnet address



QUESTION 188LLC header consists of three parts, namely,

A. SSAPB. DSAPC. Address

D. Control



QUESTION 189Which of the following are data link layer MAC sub-layer functions?

A. Definition MAC addressB. Providing an interface with the upper layer protocol communicationC. Error correctionD. Flow Control



QUESTION 190Routers forwarding data (no address translation in the case), the following items which have not been changedin the forwarding

A. Source Network AddressB. the destination network addressC. Source MAC addressD. destination MAC addressE. source port numberF. destination port number

Correct Answer: ABEFSection: (none)Explanation


QUESTION 191About the TTL IP header field, the following statements is correct

A. TTL maximum possible value is 65535B. Under normalcircumstances, the router should not be received from the interface the packet TTL = 0C. TTL is mainly to prevent the IP packet forwarding loops in the network, wasting network bandwidthD. IP packets through a network of each device, including Hub, LAN SWITCH and router, TTL value will be

subtracted from the value of certain



QUESTION 192TCP is connection-oriented reliable transport protocol, following which mechanism is used to protect thetransmission reliability

A. confirmation (acknowledgement) mechanismB. caching (buffering)C. source quench packets (source quench messages)D. Retransmission (retransmit) mechanism



QUESTION 193Which of the following flow control is the way?

A. confirmation (acknowledgement) technologyB. caching (buffering) technologyC. source quench packets (source quench messages)D. window mechanism (windowing)



QUESTION 194ICMP protocol is a protocol which the following abbreviations

A. Internal Control Mail ProtocolB. IntranetControl Message ProtocolC. Internet Connection Message ProtocolD. Internet Control Message Protocol



QUESTION 195The following description of the ICMP protocol, the correct is ().

A. ICMP protocol based on MAC address to find the corresponding IP addressB. ICMP protocol to public IP addresses to private network IP addressC. ICMP protocol is used for monitoring data transmission errors in the case reported

D. ICMP protocol to centrally manage the network IP address assignment



QUESTION 196ICMP messages typically report in the process of dealing with IP packet ().

A. DelayB. ErrorC. JitterD. Source IP



QUESTION 197ICMP packets to pass the test ().

A. ICMP packet inspection and fieldB. IP packet headerinspection andC. ICMP message code fieldD. ICMP message type field



QUESTION 198IP protocol is an unreliable protocol, error control cannot be. However, IP protocol can make use of () toachieve this functionality.

A. ARPB. ICMPC. TCPD. UDP



QUESTION 199

ICMP protocol is the protocol number

A. 1B. 6C. 17D. 22



QUESTION 200The following operation can determine which TCP / IP protocol is installed or run problems

A. ping 10.1.1.1B. ping 127.0.0.1C. ping 169.254.1.1D. ping 192.168.1.1



Exam B

QUESTION 1Which of the following program can detect the source node to destination node through which data packetsbetween the path?

A. routeB. netstatC. tracertD. send



QUESTION 2Tracer program is an application layer program, which uses the transport protocol is

A. ICMPB. ARPC. TCPD. UDP



QUESTION 3In the test program using tracert to reach the destination node by the path, the default TTL value for eachTraceroute to measure () times

A. 3B. 4C. 6D. 8



QUESTION 4Judge: ICMP protocol (RFC792) is not the application layer protocol, the network layer protocol.

A. TrueB. False



QUESTION 5ICMP message types are ().

A. ICMP packet transmissionB. ICMP error messages reportC. ICMP packets inquiryD. ICMP application packet



QUESTION 6ICMP front () bytes are unified format, a total of three fields: the type, code and checksum.

A. 3B. 4C. 5D. 8



QUESTION 7Which of the following procedures will be used ICMP protocol?

A. pingB. tracertC. igmpD. arp



QUESTION 8In the VRP platform, if you want the program to specify the IP ping echo request packet as the source address,which you can use the following parameters

A. -aB. -sC. -dD. -n



QUESTION 9ICMP packets to provide for the network layer ().

A. TroubleshootingB. Congestion ControlC. Path ControlD. inquiry service



QUESTION 10When the first packet received in some field values are not correct, it discards the datagram to the source tosend ICMP () message.

A. does not reach the destination stationB. source quenchC. Parameter problemD. Redirect



QUESTION 11When a router or host datagrams discarded due to congestion on the source station to send ICMP () message.

A. does not reach the destination stationB. source quenchC. Parameter problemD. Redirect



QUESTION 12Below () the message is the ICMP packet.

A. Echo request packetB. timestamp reply messageC. inquiry packet routerD. router advertisement message



QUESTION 13Router ICMP () message sent to the host, the host should know that the next packet sent to another router.

A. RedirectB. timestamp replyC. router inquiryD. unreachable destination station



QUESTION 14The following circumstances do not send ICMP error reporting message ().

A. Report ofthe ICMP error message itselfB. a fragment of the first piece of data reported follow-up data reported for all pieceC. multicast addresses that have reported dataD. special address 127.0.0.0 on the data reported



QUESTION 15Commonly used application layer protocol used to test the ping of connectivity between two hosts. Ping uses ICMP () message.

A. Echo request packetB. Echo response packetC. exceeded packets

D. destination unreachable message



QUESTION 16The following picture which is twisted

A. 1_5_1_1AB. 1_5_1_1BC. 1_5_1_1CD. 1_5_1_1D



QUESTION 17The following picture which is the fiber

A. 1_5_1_2AB. 1_5_1_2BC. 1_5_1_2CD. 1_5_1_2D



QUESTION 18The following figure is that a module interface connector RJ45

A. 1_5_1_3AB. 1_5_1_3BC. 1_5_1_3CD. 1_5_1_3D



QUESTION 19The following is what kind of cable used to connect devices to the console port and PC com port configuration

lines

A. 1_5_1_4AB. 1_5_1_4BC. 1_5_1_4CD. 1_5_1_4D



QUESTION 20Known figure given in the cable and interface, does this cable type is most likely

A. Standard twisted pairB. coaxial axisC. V. 24D. V. 35



QUESTION 21User ADSL Internet access at home, when using () to connect to ADSL modem and the remote central officeDSLAM equipment.

A. CoaxialB. Category 5 UTP twisted pairC. five STP twisted pairD. ordinary telephone line



QUESTION 22() root insulated copper wires to each other and side by side, and then twisted together with the rules is to formthe twisted pair.

A. 2B. 3C. 8D. 16

Correct Answer: A



QUESTION 23Usually by a different characteristic impedance values, the coaxial cable into ().

A. 25 European coaxial cableB. 50 European coaxial cableC. 75 European coaxial cableD. 100 European coaxial cable



QUESTION 24Can be many different angles of incident light in an optical fiber, the fiber is called ().

A. four-core optical fiberB. Single-mode fiberC. multimode fiberD. Active Fiber



QUESTION 25The following figure is the one SFP optical module interface connector

A. Option AB. Option BC. Option CD. Option D



QUESTION 26Out of the twisted pair plus a shield, known as (), can improve the twisted pair of resistance to electromagneticinterference.

A. STP

B. UTPC. BTPD. RPR



QUESTION 27The following description of fiber optic connectors is correct

A. FC: fiber optic circular connectors with threadedB. ST: Snap-round fiber optic connectorsC. LC: square optical connectorD. MT-RJ: The square optical transceiver connectors



QUESTION 28Analog and digital transmissions can use twisted pair wire more coarse, its communication distance ().

A. fartherB. The more recentC. and the thickness of the wire has nothing to doD. communication distance of more than 50KM, the more distant



QUESTION 29B class address of the default mask is

A. 255.0.0.0B. 255.255.0.0C. 255.255.255.0D. 255.225.255.255



QUESTION 30Which of the following subnet address that all routers.

A. 224.0.0.1B. 224.0.0.2C. 224.0.0.3D. 224.0.0.9



QUESTION 31IP address, network and host part of the address of that for the whole 0

A. Network AddressB. Specific segments of the broadcast addressC. All networksD. Ben Wang segment broadcast address of all nodes



QUESTION 32IP address 190.233.27.13 is () class Address

A. AB. BC. CD. D



QUESTION 33IP address 190.233.27.13/16 network segment where the address is

A. 190.0.0.0B. 190.233.0.0C. 190.233.27.0D. 190.233.27.1

Correct Answer: B



QUESTION 34Which of the following types used to support multicast?

A. A ClassB. B ClassC. D classD. E Class



QUESTION 35IP address 219.25.23.56 several default subnet mask

A. 8B. 16C. 24D. 32



QUESTION 36Subnet is the IP address () of the

A. network addressB. Host AddressC. subnet segmentD. The default subnet mask



QUESTION 37A Class B IP address can be used up () bit subnetting

A. 8

B. 14C. 16D. 22



QUESTION 38A Class A address subnet mask is 255.255.240.0 with () bit is used to subnetting

A. 4B. 5C. 9D. 12



QUESTION 39C class subnet address the largest possible number of bits is ()-bit

A. 6B. 8C. 12D. 14



QUESTION 40A Class B address can have about () hosts

A. 254B. 16KC. 63KD. 2M



QUESTION 41The network address is 154.27.0.0 network, if not for subnetting, can support () hosts

A. 254B. 1024C. 65,534D. 16,777,206



QUESTION 42For such a network segment 192.168.2.16/28, ask for up to () hosts.

A. 16B. 8C. 15D. 14E. 7



QUESTION 43Subnet mask 255.255.192.0 in binary is

A. 11111111 11110000 00000000 00000000B. 11111111 11111111 00001111 00000000C. 11111111 11111111 11000000 00000000D. 11111111 11111111 11111111 00000000



QUESTION 44Binary decimal value 11,001,011

A. 171B. 193C. 203D. 207



QUESTION 45The following subnet mask is the most suitable point to point link

A. 255.255.255.224B. 255.255.255.240C. 255.255.255.248D. 255.255.255.252



QUESTION 4610.0.0.24/29 may be caused by routing entry as follows () by the convergence of several stripsfrom the network

A. 10.0.0.25/30B. 10.0.0.23/30C. 10.0.0.26/30D. 10.0.0.22/30



QUESTION 47The following is a correct statement about NAT

A. NAT is in English, "Address Translation" in the acronym, also known as address translationB. NAT private address used to achieve the conversion between the public network addressC. When the internal network hosts to access external networks, they must not NATD. Address transformation proposed to solve the problem of the shortage IP address provides an effective way

to



QUESTION 48To a host IP address is 10.0.0.1 the necessary technology to access the Internet

A. Static RoutingB. Dynamic routingC. route redistributionD. NAT



QUESTION 49NAT can solve the problem is

A. Save Internet public address.B. router forwarding performance improvedC. Strengthening the security of data transmissionD. to prevent computer virus attacks



QUESTION 50Using the IP address 125.3.54.56 natural mask of the network address is

A. 125.0.0.0B. 125.3.0.0C. 125.3.54.0D. 125.3.54.32



QUESTION 51NAT is able to convert the network address

A. IPB. IPXC. AppleTalkD. DECNET



QUESTION 52Judge: IP address using hierarchical design, each three-layer network devices do not have to store the IPaddress of each host, but storing the network address of each segment, greatly reducing the routing table entry,increase the routing flexibility.

A. TrueB. False



QUESTION 53IPv4 addresses consist of 32 bit, usually in dotted decimal form, such as 11.110.96.132. In addition, IP address11.110.96.132 can also be expressed as follows

A. 00001011.01101110.01100000.10000100B. 0b.6e.60.84C. 0.b.6.e.6.0.8.4D. 0.1011.0110.1110.0110.0.1000.0100



QUESTION 54IP address 191.10.96.132 using natural mask, 191.10.96.132 is the network address ().

A. 191.0.0.0B. 191.10.0.0C. 191.10.48.0D. 191.10.96.0



QUESTION 55IP address part of the fixed network, the host part of all 1's address indicated ().

A. Network AddressB. Specific segments of the broadcast addressC. All network

D. Ben Wang broadcast address of all nodes



QUESTION 56When the IP address of the host part of the median of n, then the network number of host addresses available()

A. 2n-1B. 2n-2C. 2n-1D. 2n



QUESTION 57C class IP address of the network address for the first three octet, the first byte to () started.

A. 101B. 100C. 110D. 10



QUESTION 58IP address where the network address of 192.168.1.7/28 ().

A. 192.168.1.0B. 192.168.1.4C. 192.168.1.6D. 192.168.1.7



QUESTION 59

IP address 192.168.1.7 with natural mask, its network address ().

A. 192.168.1.0B. 192.168.1.4C. 192.0.0.0D. 192.168.0.0



QUESTION 60The first octet to binary IP address is the beginning of 1110 () address

A. A ClassB. B ClassC. C CategoryD. D type



QUESTION 61ARP protocol is a () protocol.

A. UnicastB. MulticastC. MulticastD. Radio



QUESTION 62Proxy ARP feature enabled, the router receives an ARP request packet, the packet's destination address that isnot their own, will be as follows ().

A. dropping packetsB. Find whether the route to the destination addressC. there is a route to the destination address, MAC address will be sent to their side ARP requestD. broadcast ARP request packets

Correct Answer: BCSection: (none)

Explanation


QUESTION 63Corresponds to the RARP request is broadcast to send, RARP response generally () sent to save networkresources.

A. UnicastB. MulticastC. MulticastD. Radio



QUESTION 64Reserved for loopback testing of the IP address of the segment is

A. 127.0.0.0B. 130.0.0.0C. 164.0.0.0D. 200.0.0.0



QUESTION 65In the TCP / IP protocol, A class of first byte of the address range

A. 0 --- 126B. 0 --- 127C. 1 --- 126D. 1 --- 127



QUESTION 66In the destination MAC address, the address of the first () decides whether the frame will be sent to a single siteor a site.

A. 7

B. 8C. 9D. 10



QUESTION 67For a traditional without subnetting Class C network address, the host can accommodate the maximum numberof

A. 1024B. 65025C. 254D. 48



QUESTION 68IP address in the role of the network number

A. Specify the host's network belongsB. The host network logoC. Specify the network device can communicateD. Specify the subnet to be addressed in a node



QUESTION 69Which of the following subnet multicast address that all routers and hosts

A. 224.0.0.1B. 224.0.0.2C. 224.0.0.3D. 224.0.0.9



QUESTION 70Subnet on the IP network address space the size of the argument right there

A. subnet space must meet the actual needs; there should be some redundancy in order to ensure scalabilityB. Because you can use the IP address of the borrowing and other technical means, so as to save the IP

address, subnet space should generally be less than the actual needsC. subnet space should generally try to make up the size of a power of 2, to facilitate theimplementation of

various strategiesD. above comments have some truth, but they cannot be applied in engineering practice



QUESTION 71A segment 150.25.0.0 subnet mask is 255.255.224.0, () is a valid host address

A. 150.25.0.0B. 150.25.1.255C. 150.25.2.24D. 150.15.3.30



QUESTION 72In a subnet mask of 255.255.240.0 the network, () is a legitimate network address

A. 150.150.0.0B. 150.150.0.8C. 150.150.8.0D. 150.150.16.0



QUESTION 73Subnet mask for the network address of 5.32.0.0 255.224.0.0 network, which is the maximum allowed hostaddress

A. 5.32.254.254B. 5.32.255.254

C. 5.63.255.254D. 5.63.255.255



QUESTION 74Subnet mask is the network segment 175.25.8.0/19

A. 255.255.0.0B. 255.255.224.0C. 255.255.24.0D. depends on the type of address



QUESTION 75172.16.10.32/24 represents

A. Network AddressB. Host AddressC. Multicast AddressD. broadcast address



QUESTION 76If the class C subnet mask of 255.255.255.224, the subnet that contains the median number of subnets, thenumber of hosts per subnet is correct

A. 2,4,62B. 3,8,30C. 4, 16, 14D. 5,32,6



QUESTION 7710.1.0.1/17 broadcast address is

A. 10.1.128.255B. 10.1.63.255C. 10.1.127.255D. 10.1.126.255



QUESTION 78Known to a network mask is 255.255.248.0, and then the following segment is the same

A. 10.110.16.1 and 10.110.25.1B. 10.76.129.21 and 10.76.137.1C. 10.52.57.34 and 10.52.62.2D. 10.33.23.2 and 10.33.31.1



QUESTION 79In a Class C address segment to be divided into 32 subnets, subnet mask below that best

A. 255.255.255.224B. 255.255.255.240C. 255.255.255.255D. 255.255.255.248



QUESTION 80IP address planning, good or bad, can affect

A. network routers routing table sizeB. network routing algorithm efficiencyC. Network ManagementD. network expansion

Correct Answer: ABCD



QUESTION 81101.11.100.100/22 host address is the broadcast address

A. 101.11.100.255B. 101.11.101.255C. 101.11.103.255D. 101.255.255.255



QUESTION 82201.1.0.0/21 segment of the broadcast address is

A. 201.1.7.255B. 201.1.0.255C. 201.1.1.255D. 201.0.0.255



QUESTION 83The following address can be the legal address of a PC are

A. 221.0.0.1/24B. 224.0.0.5/28C. 30.10.1.15/28D. 12.2.2.2/30



QUESTION 84For this a few segments: 172.128.12.0,172.128.17.0,172.128.18.0,172.128.19.0 best with the following () forrouting segment summary

A. 172.128.0.0/21

B. 172.128.0.0/19C. 172.128.12.0/22D. 172.128.20.0/20



QUESTION 85Using CIDR technology, the following () can correctly route aggregation

A. 192.168.1.0-192.168.15.0 converging 192.168.0.0/19B. 192.168.1.0-192.168.15.0 converging 192.168.0.0/20C. 192.168.1.0-192.168.15.0 converging 192.168.0.0/21D. 192.168.1.0-192.168.15.0 converging 192.168.0.0/22



QUESTION 86For this a few segments: 172.168.16.0,172.168.17.0,172.168.18.0,172.168.19.0 best with the following () forrouting segment summary

A. 172.168.16.0/21B. 172.168.17.0/21C. 172.168.16.0/22D. 172.168.20.0/20



QUESTION 87The following statement on the correct route aggregation is

A. routing aggregation technology can only address the hierarchical structure of the system to use, the addressfor the planar structure is not

B. routing aggregation technology can be an organization for all IP addresses as a routing routing convergencerouting tables thus reducing the number of routing entries

C. External routing aggregation technology can be screened subnet topology change within theD. Dynamic routing aggregation can be a dynamic routing protocol implementation, but a variety of different

dynamic routing protocols for route summarization is not the same degree of support

Correct Answer: ABCDSection: (none)

Explanation


QUESTION 88NAPT which elements can be converted

A. MAC address + port numberB. IP address + port numberC. Only the MAC addressD. only the IP address



QUESTION 89The following are valid IP host address is ().

A. 129.0.0.130/25B. 210.12.46.7/16C. 230.19.100.32D. 225.38.9.18



QUESTION 90220.32.59.31/27 belongs to () address.

A. C class addressB. Specific segments of the broadcast addressC. Illegal addressD. Private Address



QUESTION 91Segment 220.32.59.0/27 subnet mask is 255.255.255.224, as follows () is a valid host address.

A. 220.32.59.160B. 220.32.59.17

C. 220.32.59.64D. 220.32.59.128



QUESTION 92In a subnet mask is 255.240.0.0 network, as follows () is a Class A valid host addresses.

A. 12.32.59.160B. 129.32.59.17C. 158.32.59.64D. 220.32.59.128



QUESTION 93In a subnet mask is 255.255.192.0 the network, as follows () is a valid host address.

A. 12.32.59.160B. 129.32.59.17C. 199.32.59.64D. 220.32.59.128



QUESTION 94C class subnet mask is 255.255.255.192, subnet contains the number, the number of hosts per subnet is ().

A. 4, 62B. 8, 62C. 16, 14D. 32, 14



QUESTION 95The following segment is part of the private address:

A. 10.0.0.0 / 8B. 172.16.0.0/12C. 192.168.0.0/16D. 224.0.0.0 / 8



QUESTION 96192.168.1.127/25 represent () address

A. HostB. NetworkC. MulticastD. Radio



QUESTION 97In the OSI model, the network layer address by which two parts

A. network address and host addressB. host address and network maskC. Network address and network maskD. host address and host ID



QUESTION 98On an IP host address, the following statements is correct

A. You can host part of all 1B. segment part can also be full full 1 0C. cannot be wholly a part of the segment cannot all 0D. can host part of all 0

Correct Answer: CSection: (none)

Explanation


QUESTION 99The following is the correct IP address of the host

A. 224.0.0.5/24B. 127.32.5.62 / 8C. 202.112.5.0/24D. 162.111.111.111/16



QUESTION 100In which of the following cases, the data packets based on source and destination IP address is to determinethe host address

A. Radio (Broadcast)B. Multicast (Multicast)C. unicast (Unicast)D. Live (Dircast)



QUESTION 101A class B network, there are five mask added to the default subnet mask for each subnet up () hosts

A. 510B. 512C. 1022D. 2046



QUESTION 102A company to apply to a Class C IP addresses need to be allocated to eight subsidiary companies, the largestsubsidiary, has 14 computers, a segment in each subsidiary, the subnet mask should be set

A. 255.255.255.0

B. 255.255.255.128C. 255.255.255.192D. 255.255.255.224



QUESTION 103With 10.110.12.29/27 belong to the same segment of the host IP address is

A. 10.110.12.0B. 10.110.12.30C. 10.110.12.31D. 10.110.12.32



QUESTION 104For such an address, 192.168.19.255/20, the following statements is correct:

A. This is a broadcast addressB. This is a network addressC. This is a private addressD. segment address 192.168.19.0E. Address in the 192.168.16.0 network segmentF. This is a public address

Correct Answer: CESection: (none)Explanation


QUESTION 105A company to apply to a Class C IP addresses, but to connect six subsidiaries, the largest subsidiary, has 26computers, a segment in each subsidiary, the subnet mask should be set

A. 255.255.255.0B. 255.255.255.128C. 255.255.255.192D. 255.255.255.224



QUESTION 106C class network, increase the 3 mask is used to add the default subnet mask for each subnet number up to thehost ().

A. 62B. 30C. 14D. 6



QUESTION 107IP address 12.28.75.160, subnetting, the subnet mask is 255.255.252.0, then the IP address of the subnetbroadcast address ().

A. 12.28.255.255B. 12.28.69.255C. 12.28.75.255D. 12.255.255.255



QUESTION 108IP address 129.32.59.17, subnet, the subnet mask is 255.255.254.0, then the number of available subnets ().

A. 256B. 128C. 64D. 32



QUESTION 109IP address 220.32.59.128/25 network address ().

A. 220.32.59.192

B. 220.32.59.128C. 220.32.59.254D. 220.32.59.0



QUESTION 110On a gratuitous ARP statement is correct ().

A. ARP can be confirmed by sending a free IP address conflictB. ARP packets are ARP request packet formatC. Free ARP can help update the old IP address informationD. ARP packets are ARP response packet format



QUESTION 111Planning a class C network, the network needs to be divided into nine sub, up to 16 hosts per subnet, which isthe appropriate subnet mask for the following

A. 255.255.224.0B. 255.255.255.224C. 255.255.255.240D. No appropriate subnet mask



QUESTION 112For network 172.168.16.0 MASK 255.255.252.0, subnet and its neighbors is

A. 172.168.20.0B. 172.168.24.0C. 172.168.32.0D. 172.168.48.0



QUESTION 113Assume an IP address to you the following: 192.168.12.43, subnet mask: 255.255.255.128, then the networkaddress broadcast address is ____, ____

A. 192.168.12.32 192.168.12.127B. 192.168.0.0 255.255.255.255C. 192.168.12.43 255.255.255.128D. 192.169.12.128 255.255.255.128E. 192.168.12.0 192.168.12.127

Correct Answer: ESection: (none)Explanation


QUESTION 114You have been assigned a Class B IP network 155.16.0.0, subnet, the subnet mask of 255.255.255.192, youcan use the network number is ___, the maximum number of hosts per segment is ___

A. 512, 126B. 1022, 64C. 1024, 62D. 256, 254E. 92, 254



QUESTION 115IP address of 190.5.4.2 / 22 of the subnet network address and broadcast address is

A. 190.5.4.0, 190.5.7.255B. 190.5.4.0, 255.255.255.255C. 190.5.0.0, 190.5.4.255D. 190.5.4.0, 190.5.4.255



QUESTION 116The following address () is available host IP address.

A. 192.168.2.15/28

B. 10.0.2.128/26C. 122.245.264.13/26D. 12.3.4.6/24E. 224.0.4.5



QUESTION 117Assuming that the IP address 190.5.6.1, subnet mask 255.255.252.0, then the IP address where the segmentand subnet broadcast address are

A. 190.5.4.0 190.5.7.255B. 190.5.4.0 190.5.4.255C. 190.5.4.0 190.5.4.254D. 190.5.1.0 190.5.1.255



QUESTION 118If the IP address 10.110.53.233 Mask length of the mask with the following options in the same length, with10.110.53.233 in the same network have

A. 10.110.48.10 mask 255.255.248.0B. 10.110.43.10 mask 255.255.0.0C. 10.110.43.10 mask 255.255.248.0D. 10.110.48.10 mask 255.255.252.0



QUESTION 119DHCP is what the following abbreviations of English words

A. Dynamic Host Configuration ProtocolB. Dynamic Host Connection ProtocolC. Dynamic Hot Connection ProtocolD. Denial Host Configuration Protocol



QUESTION 120Which of the following protocol is used to transfer e-mail on the Internet?

A. SMTPB. MSTPC. FTPD. TFTP



QUESTION 121SMTP protocol based on TCP for transport, the port number is

A. 21B. 23C. 25D. 53



QUESTION 122POP's full name is the Post Office Protocol, is used to receive e-mail, it uses the TCP () port

A. 110B. 53C. 21D. 23



QUESTION 123Judge: TFTP TFTP can provide the user's login name and password control.

A. TrueB. False



QUESTION 124Usually used in remote services, () provides a user terminal through the Internet logon to the remote servermode.

A. FTPB. TFTPC. TELNETD. TRACERT



QUESTION 125Telnet transport protocol port number to use is ().

A. 23B. 24C. 8080D. 48



QUESTION 126() Is used to check whether the IP network connections and hosts up to the most common method. Such as arouter between the host and the connectivity between the router problems can use it to judge.

A. DNSB. FTPC. PINGD. TFTP



QUESTION 127Ping uses a series of () messages to determine the communication delay and packet loss.

A. FTPB. TracertC. ICMPD. Telnet



QUESTION 128Huawei router device, VRP operating system of the Ping command-i parameter ().

A. Send Echo Request packet interfaceB. Echo Request packets to send the source IPC. Echo Reply messages received interfaceD. Receive Echo Reply packet destination IP



QUESTION 129DHCP protocol in the OSI reference model, which is a level of agreement




QUESTION 130() Is used to view the IP datagrams from one host to another host through the route.

A. FTPB. TracertC. ICMPD. Telnet



QUESTION 131Tracert record each ICMP TTL timeout message (), thus providing the user through which thepacket reaches the destination IP address.

A. Purpose PortB. source portC. Destination address.D. source address



QUESTION 132Telnet transport protocol to use ().

A. TCPB. UDPC. ECMPD. UCMP



QUESTION 133SSH is an abbreviation which of the following English words

A. Secure shellB. Secure session hostC. Secure session homeD. Session shell



QUESTION 134DNS's main role is

A. DNSB. Remote accessC. File Transfer

D. Mail Transfer



QUESTION 135HTTP represents

A. Hypertext Transfer ProtocolB. Hypertext Translate ProtocolC. Hypertest Transmit ProtocolD. Hypertext Transmit Protocol



QUESTION 136HTTP protocol using TCP communication, the default port is

A. 80B. 8080C. 110D. 25



QUESTION 137FTP protocol is based on which of the following protocols to provide reliable data transmission

A. RTPB. SIPC. UDPD. TCP



QUESTION 138Which of the following file transfer protocols can be?

A. FTPB. TFTPC. XmodemD. icmp



QUESTION 139DHCP protocol uses what protocol to transmit packets

A. TCPB. UDPC. RTPD. SIP



QUESTION 140TRACERT process, the agreement will not be used is ().

A. TCPB. UDPC. ICMPD. ARP



QUESTION 141PING and TRACERT on to say, the right is ().

A. Both can be used to test network connectivityB. Ping can send packets of the specified source IP, etc.C. Ping is used to obtain more data packet forwarding pathD. Tracert to determine the initial point of failure



QUESTION 142On the FTP, the following statement is correct ().

A. FTP is a protocol based on UDPB. FTP is designed for low-speed file transferC. FTP can provide FTP user login name and password controlD. router can support FTP Client and FTP Server in two modes



QUESTION 143TFTP statement on the right is ().

A. TFTP is a UDP-based protocolB. TFTP is a simple file transfer protocol, suitable for read-only memoryC. TFTP TFTP can provide the user's login name and password controlD. TFTP Client mode only supports



QUESTION 144Telnet protocol uses the port number is

A. 23B. 25C. 27D. 29



QUESTION 145Telnet protocol is based on which the transport protocol for data transmission

A. RTPB. SIPC. UDPD. TCP



QUESTION 146FTP server default port number () to listen for FTP client to connect

A. 21B. 23C. 25D. 53



QUESTION 147In using the FTP protocol router software upgrade, the transfer mode should be selected

A. Binary modeB. Flow-byte modeC. byte modeD. Text mode



QUESTION 148In data transfer using the FTP protocol, the default server port is the data channel

A. 20B. 21C. 23D. 25



QUESTION 149FTP session consists of two channels, namely

A. Output channelB. Input channelC. Control channelD. Data Channel



QUESTION 150TFTP client to connect to the TFTP server, the target port is

A. 20B. 21C. 53D. 69



QUESTION 151The following TCP-based applications with ().

A. PINGB. BGPC. TELNETD. OSPF



QUESTION 152In Windows XP system in order to release the current through DHCP IP, use the command

A. ipconfig / allB. ipconfig / renewC. ipconfig / releaseD. ipconfig



QUESTION 153In terms of relative Telnet, SSH which has the following advantages?

A. can encrypt all data transmitted, so as not to be "middle" attackB. to prevent the DNS and IP spoofingC. Transfer of data is compressed, so it can accelerate the transmission speedD. UDP-based connections, for large-scale use



QUESTION 154Based on ISO3166 country code defined in some domain known as the National domain, orgeographic domain, the following is a geographic domain name

A. cnB. ukC. usD. com



QUESTION 155The following protocols and applications are based on TCP implementation ().

A. FTPB. DNSC. SNMPD. Telnet



QUESTION 156The following protocols and applications are implemented based on UDP ().

A. FTPB. DNSC. SNMPD. Telnet



QUESTION 157Applications are sent PING () message.

A. TCP request packetB. TCP response packetC. ICMP request messageD. ICMP reply packet



QUESTION 158Which of the following command to check the application layer protocol is working properly ().

A. PINGB. TRACEC. Extended pingD. TELNET



QUESTION 159Frequently used data network debugging Tracert, in its working mechanism, the total use of () kindof ICMP packets.

A. 2B. 3C. 4D. 6



QUESTION 160In the standard Ethernet, to avoid multiple devices at the same time to seize the line mechanism

called

A. CSMA / CAB. CSMA / DAC. CSMA / C, DD. CSMA / A, C



QUESTION 161Thin coaxial cable transmission distance is

A. 100B. 200C. 50D. 500



QUESTION 162Category 5 UTP twisted pair transmission distance of 100 megabytes is the maximum

A. 100B. 200C. 50D. 185



QUESTION 163If you want to connect two computers directly via twisted pair, the correct line sequence is

A. Both computers can connect directly through twisted-pairB. 1 - 1,2 - 2 ,3 - 3 ,4 - 4 ,5 - 5 ,6 - 6 ,7 - 7 ,8 - 8C. 1 - 3,2 - 6 ,3 - 1 ,4 - 4 ,5 - 5 ,6 - 2 ,7 - 7 ,8 - 8D. 1 - 2,2 - 1 ,3 - 6 ,4 - 4 ,5 - 5 ,6 - 3 ,7 - 7 ,8-8



QUESTION 164PC machines connected to the router via the Ethernet LAN port, two interfaces should be usedbetween the cable is

A. crossover cableB. Standard cableC. Configure the cableD. backup cable



QUESTION 165Switch is working in the OSI Reference Model () equipment




QUESTION 166Switch receives the complete frame, run the CRC check is passed to forward frames, this is called forwardmode () forward mode

A. Cut-ThroughB. Store-and-ForwardC. Fragment-freeD. Store-free



QUESTION 167Switch receives the data frame header, the header's destination MAC address based forwarding framesimmediately, this is called forward mode () forward mode

A. Cut-Through

B. Store-and-ForwardC. Fragment-freeD. Store-free



QUESTION 168Relative to the HUB second floor switch which has the following advantages

A. Reducing conflictB. higher throughputC. greater port densityD. Narrow range of collision domains.



QUESTION 169Can be used to coordinate port auto-negotiation technology, the speed, duplex mode and so on. When thenegotiating parties will support a variety of ways of working, which has the highest priority

A. 100BASE-T4B. 100BASE-TX full duplexC. 100BASE-TXD. 10BASE-T full-duplex



QUESTION 170The following IEEE standards, provides flow control standard is

A. 802.1QB. 802.3uC. 802.3zD. 802.3x



QUESTION 171() Is to aggregate multiple ports together to form a group together to achieve entry / exit load on each member'sshare of the port, but also provides higher connection reliability

A. Port AggregationB. Port BindingC. Port load balancingD. port group



QUESTION 172Judge: thick coaxial cable 10Base5, 5 on behalf of the cable with a maximum distance of 500 meters.

A. TrueB. False



QUESTION 173Twisted pair can be classified as ().

A. Straight-line networkingB. Crossover cableC. woven cableD. shielded cable



QUESTION 174Network device interface is divided into the following two ().

A. MDIB. MDI_SC. MDI_XD. MDI_R

Correct Answer: AC



QUESTION 175General router's Ethernet interface, the host of the NIC (Network Interface Card) interface type ().




QUESTION 176Hub (hub) interface type ().




QUESTION 177Can switch the interface type () two.




QUESTION 178Used to connect the network interface between devices of different types of network cable is ().

A. Straight-line networking

B. Crossover cableC. woven cableD. shielded cable



QUESTION 179For connecting network devices of its kind in the interface cable is ().

A. Straight-line networkingB. Crossover cableC. woven cableD. shielded cable



QUESTION 180IEEE developed a data transfer rate of 100Mbps Fast Ethernet standards, transmission media including fiberoptic and twisted pair. Single-mode fiber (SMF) cable transmission distance ().

A. equal to 1KmB. greater than 2KmC. less than 550mD. equal to 2Km



QUESTION 181Each MAC address consists of two parts, namely, vendor code and serial number. Which the first 24-bit binarycode representing the supplier, the following code which is code for Huawei

A. 00e0fcB. 0010feC. 000001D. 0003cf



QUESTION 182100BaseTX Fast Ethernet cable and the transmission distance 100BaseT4 ().

A. 100mB. 550mC. 1000mD. 2000m



QUESTION 1831000BaseT Gigabit Ethernet cable transmission distance ().

A. 100mB. 550mC. 1000mD. 2000m



QUESTION 184Ethernet, which has several rate ().

A. 10MB. 100MC. 1000MD. 10G



QUESTION 185Judge: Hub of the works: an interface received from any non-selective data frames transmitted to any other port

A. TrueB. False

Correct Answer: A



QUESTION 186Hub works as ().




QUESTION 187About the statement is correct HUB

A. HUB is a physical layer deviceB. HUB is the data link layer devicesC. HUB network layer devicesD. HUB is the application layer device



QUESTION 188Which of the following standard is a standard Ethernet?

A. IEEE 802.3B. IEEE 802.3uC. IEEE 802.3z/abD. IEEE 802.3ae



QUESTION 189Which of the following is the Fast Ethernet Standard?

A. IEEE 802.3

B. IEEE 802.3uC. IEEE 802.3z/abD. IEEE 802.3ae



QUESTION 190Which of the following is the standard Gigabit Ethernet Standard?




QUESTION 191Which of the following is the Gigabit Ethernet Standard?




QUESTION 19210Base 2 using () for data transmission

A. CoaxialB. twisted pairC. fiberD. Radio waves



QUESTION 193Ethernet physical media are used

A. CoaxialB. twisted pairC. CableD. V.24 cable



QUESTION 194Layer 2 Ethernet switch works include ()

A. port is connected to receive all data frames on the segmentB. The use of received data frames to create the source MAC address MAC address tableC. The MAC address table to find data in the frame destination MAC address, if found on the data frame sent

to the appropriate port (not including source port); If not, the source port to the outside in addition to all theports send

D. Use the address aging address table maintenance mechanism



QUESTION 195IEEE802.3 frame contains () bit DSAP field, high-level protocol used to indicate

A. 8B. 4C. 16D. 24



QUESTION 196Ethernet data frame is the last field in the frame check sequence (FCS), the field is occupied by () bytes

A. 2B. 4C. 8D. 32



QUESTION 197The following exchange on the Ethernet switch in the narrative, which is correct

A. Store and Forward method does not detect the frame errorB. Cut-through mode, the switch receives a frame of 64 bytes before forwarding the frame beganC. Fragment-free way to detect frame errors in the first 64 bytesD. Store and forward discards the total length of less than 64 bytes of the frame



QUESTION 198Collision domains and broadcast domains on the right is described

A. devices connected to a Hub is a collision domainB. A Hub of the connected device is a broadcast domainC. A bridge connected device is a collision domainD. A bridge connected device is a broadcast domainE. a router connected to the device belongs to a broadcast domain



QUESTION 199Port mirroring refers to the specific business data copy, sent to the monitoring equipment, and then mirror thedata analysis, generally used in flow observation and fault location. Port mirroring can be divided into () in two

A. Port-based mirroringB. Application-based imageC. Flow-based MirroringD. Agreement on the upper mirror



QUESTION 200

MAC address of 48 bits, usually expressed as a 12-bit dotted hexadecimal number. If the full 48-bit is 1, itindicates that the address is ().

A. Multicast AddressB. Broadcast AddressC. Unicast AddressD. virtual address



Exam C

QUESTION 1Common L2 switch MAC address table by MAC address and switch () to establish the mapping.

A. RARP tableB. transmission mediumC. PortD. ARP table



QUESTION 2Multiple computers through a network cable connected to a HUB, in the logical structure of this

A. Star topologyB. Tree TopologyC. mesh topologyD. Ring topologyE. bus topology

Correct Answer: ESection: (none)Explanation


QUESTION 3L2 switch MAC forwarding forwarded check for the table does not contain the address, by () the way forward.

A. MulticastB. BroadcastC. UnicastD. Find a route



QUESTION 4IP network the same network segment, the Ministry of Communications, through the () function to completeinteroperability.

A. Physical LayerB. two-storyC. Three

D. Application layer



QUESTION 5L3 switch Ethernet frames according to the () to determine the address of the address field is the Layer 2forwarding or three forwards.

A. Destination MACB. source MACC. Destination IPD. Source IP



QUESTION 6L3 switch the main features of the following statements is correct ().

A. In a second floor features three functions while providingB. Many find three switches used to achieve accurate three-layer forwardingC. most of the Ethernet interface only three switches and ATM LAN Emulation InterfaceD. In order to improve the high-end three-layer switch uplink efficiency, and some also offer highspeed POS

interfaces



QUESTION 7Which of the following situations will make more than one station in the same collision domain?

A. multiple workstations through the network cable connected to a HUBB. multiple workstations through the network cable to an Ethernet switchC. multiple workstations through the network cable to a routerD. multiple workstations through the network cable to a bridge



QUESTION 8About HUB functionality provided is not correct:

A. Working in the physical layerB. is a shared network device, that is, each time only one device sends dataC. Work in the data link layerD. has a binary bit stream shaping enlarge and increase the role of transmission distance



QUESTION 980 late, unshielded twisted pair UTP appeared, and quickly get a wide range of applications. UTP advantages:

A. cheapB. producing simpleC. encrypted using a different cableD. physical topology and logical topology is still a bus



QUESTION 10In Ethernet, a reasonable way to eliminate the conflict

A. Increasing the length of cableB. reduce the transmission of data packetsC. each segment to reduce the number of usersD. using switches or bridges to replace the HUB and repeater



QUESTION 11The following statement on the conflict is not correct

A. Each switch port is a separate collision domainB. switch port connected to a network conflict will affect the other network port connectionC. use the bridge to replace a network HUB can increase the number of collision domains in the networkD. Reducing the number of hosts on a network can reduce the probability of the occurrence of conflict

Correct Answer: BSection: (none)

Explanation


QUESTION 12Switch is based on () for data forwarding device

A. Source MAC addressB. Destination MAC addressC. source IP addressD. destination IP address



QUESTION 13Layer 2 Ethernet switch according to the port received the packet () to generate address forwarding

A. Source MAC addressB. Destination MAC addressC. source IP addressD. destination IP address



QUESTION 14100BaseT4 Ethernet cable types

A. 3 class UTPB. 4 class UTPC. 5 UTP CategoryD. 6 UTP Category



QUESTION 15Port aggregation of multiple connection ports bundled into a logical connection, the bandwidth is tied after ().

A. Any two members of the bandwidth of the port andB. All members of the port's total bandwidth

C. All members of the port half of the total bandwidth ofD. bandwidth, the bandwidth of the highest members of the port



QUESTION 16To the mirror port and out of a complete copy of the data packet to the mirror port, this mirroring method isbased on the () mirror.

A. LinkB. peerC. FlowD. Port



QUESTION 17Port mirroring configuration, which of the following steps must be configured ().

A. redirectB. aclC. classifyD. behavior



QUESTION 18Ethernet auto-negotiation function from () to achieve, so do not use special data packet.

A. Application LayerB. network layerC. Data Link LayerD. PHY



QUESTION 19Standard Ethernet frame data field length () bytes

A. 40-1500B. 46-1500C. 64-1500D. 64-1518



QUESTION 20Through an Ethernet frame capture tool caught, found that the frame of Type / Length field is 0x0800, thefollowing description of the frame is correct

A. The frame is a frame structure Ethernet_IIB. The frame of the frame structure is 802.3C. The frame is carrying an IP packetD. The frame carrying the packet is an IPX



QUESTION 21In Huawei's switches, by () command can set the port duplex mode auto-negotiation

A. duplex fullB. duplex halfC. duplex autoD. undo duplex



QUESTION 22Which of the following command to configure Ethernet port, to ensure that congestion occurs in the link buffercannot overflow?

A. flow onB. flow-controlC. flow controlD. enable flow-control



QUESTION 23in full-duplex environment, when the port is blocked, the switch sends to the source of information PAUSEframe, tell the source of information for some time and then pause to send information. The practice of"PAUSE" frame to achieve flow control method is suitable for which environment

A. A-to-endB. A switch and a terminalC. stable network congestionD. The link between the switch and switchE. end to end flow control



QUESTION 24Huawei in two low-end switches by aggregating port, the following factors must be consistent with both ends

A. The number of link aggregationB. the rate of link aggregationC. duplex link aggregated wayD. STP, QoS, VLAN-related configuration



QUESTION 25Ethernet Interface can be operated in three different duplex mode, Ethernet optical interfaces can only work in().

A. Full-duplexB. Half-duplexC. auto-negotiationD. simplex



QUESTION 26Port aggregation is to aggregate multiple ports together to form an aggregation group, in order to achieveentry / exit load on each member's share of the port. Port aggregation in () to achieve.




QUESTION 27STP is the () stands

A. Rapid Spanning Tree ProtocolB. shortest path tree protocolC. Spanning Tree ProtocolD. shared tree



QUESTION 28STP was introduced at the switch, it's a port from learning state to forwarding state to undergo a forwardingdelay, the default is the forwarding delay () s

A. 10B. 15C. 20D. 30



QUESTION 29below on the spanning tree protocol described in the Learning state error is

A. Learning the status of the port can send and receive BPDU packetsB. Learning the status of the port can learn the source MAC address of the packetC. Learning the status of the port only to learn the source MAC address, does not forward packetsD. Learning part of the state's ports can forward data packets



QUESTION 30below on the spanning tree protocol described in the Blocking state error is

A. Blocking ports that can receive BPDU packetsB. Blocking ports that do not learn the source MAC address of the packetC. Blocking ports that do not forward data packetsD. Blocking ports that do not receive any message



QUESTION 31Below on the spanning tree protocol described in the Forwarding state error is

A. Forwarding ports that can receive BPDU packetsB. Forwarding ports that do not learn the source MAC address of the packetC. Forwarding ports that can forward data packetsD. Forwarding ports that can send BPDU packets



QUESTION 32In the STP protocol, set all the switches are configured the same priority, the MAC address of switch 1 00-e0-fc-00-00-40, the MAC address of the switch 2 00-e0-fc-00-00 -10, the MAC address of the switch 3 00-e0-fc-00-00-20, the MAC address of the switch 4 is 00-e0-fc-00-00-80, is the root switch should be

A. Switch 1B. Switch 2C. Switch 3D. Switch 4



QUESTION 33

Spanning Tree Protocol failure in the processing chain, in order to prevent temporary loops produced using the() timer

A. Hello TimeB. Forward DelayC. Max AgeD. Message Age



QUESTION 34In order to calculate the spanning tree, need to exchange information between devices and parameters, andparameters such information is encapsulated in (), passing between devices.

A. TCP BPDUB. Configuration BPDUC. Configure STPD. Configure RSTP



QUESTION 35STP protocol packets spanning tree, all the bridges in the select () a root bridge.

A. 1B. 2C. 3D. 4



QUESTION 36STP protocol convergence, and the root port directly connected to the terminal port is

A. Designated portsB. Backup portC. Alternate portD. Edge port

Correct Answer: A



QUESTION 37IEEE standard is defined in the STP

A. 802.1PB. 802.1WC. 802.1DD. 802.1Q



QUESTION 38STP protocol packets spanning tree root bridge is elected based on comparison ().

A. Bridge IDB. Path CostC. Port CostD. Port ID



QUESTION 39To determine: the root bridge, root port and designated port.

A. TrueB. False



QUESTION 40STP port cost calculation (Port Cost) and the port bandwidth, the higher the bandwidth, the more expensive ().

A. SmallB. majorC. the same

D. is not necessarily



QUESTION 41Judge: from a non-root bridge to reach the root bridge of a number of possible paths, each path has a total costvalue; this value is the path cost of all the ports of port cost sum.

A. TrueB. False



QUESTION 42STP to calculate the non-root bridge to the root path of the total cost of bridge equipment, including the path ofleast total cost of non-root bridge through which port on the device known as().

A. Designated portsB. Root PortC. Common PortsD. queue port



QUESTION 43STP calculation of the port identifier consists of two parts: 1 byte length () and 1-byte length of the port number.

A. Port PriorityB. Priority LinkC. Bridge MACD. port MAC



QUESTION 44When the story appeared redundant path switched network, the method used to stop the loop, increase

network reliability

A. Spanning Tree ProtocolB. Split horizonC. Poison ReverseD. shortest path tree



QUESTION 45In accordance with the OSI model, Layer 2 Ethernet switch in which a layer of work

A. Physical LayerB. Data Link LayerC. IP layerD. Application layer



QUESTION 46The following description on the right Ethernet switch is

A. Ethernet switches based on message content to determine whether a loop existsB. Ethernet switch in the data forwarding may need to modify the message contentC. Ethernet switch is transparent to users; it does not the contents of packets forwarded by any changesD. Ethernet switches in the presence of the same loop can work



QUESTION 47The following description of the specified port on the spanning tree is correct

A. Each bridge has only one designated portB. Specify the port to its associated segment is responsible for forwarding packetsC. A designated port is a path leading to the root switchD. specified port forwarding from the switch to the root switch data packets



QUESTION 48Spanning Tree Protocol The basic idea is to pass through the bridge between the information to construct aspecial loop-free tree, called the news of this special

A. Configure a messageB. notification messageC. Hello messagesD. Update News



QUESTION 49Switches running STP, default switch priority

A. 4096B. 8192C. 16384D. 32768



QUESTION 50If there is Layer 2 switched network in the loop, will result in () occurs

A. Broadcast StormB. route from the ringC. destination network unreachableD. MAC address table instability



QUESTION 51The following spanning tree protocol on port state transition in the description of the error is

A. Forwarding state to Blocking state can moveB. Learning state to the Blocking state can move

C. Learning state moved to Forwarding state can be directlyD. Blocking the state moved to Forwarding state can be directly



QUESTION 52STP calculated for each segment designated ports and designated bridge elections, when compared to the firstsegment is connected to the port-owned equipment (), the smaller the priority.

A. Link PriorityB. root path costC. Port logoD. port MAC



QUESTION 53For the physical layer and data link layer can work, and a STP-enabled device port, STP port roles are definedfor three, respectively ().

A. Root PortB. Designated PortC. Alternate PortD. Disable Port



QUESTION 54And the end of the designated ports of directly connected, does not forward any packets, but receive BPDU portto listen for changes in the network is ().

A. Root PortB. Designated PortC. Alternate PortD. Disable Port



QUESTION 55STP port in the calculation () state, no forwarding of data frames, not learning the MAC address table, only thespanning tree calculation, receiving and sending STP packets.

A. ListeningB. BlockingC. LearningD. Forwarding



QUESTION 56STP port in the calculation () state, no forwarding of data frames, not learning the MAC address table, the stateport to receive and deal with STP packets, but does not send out STP packets.

A. ListeningB. BlockingC. LearningD. Forwarding



QUESTION 57The following description of Layer 2 Ethernet switch, is not correct is

A. to take the initiative to learn the MAC addressB. Need for the three packet forwarding head to do some changes, and then forwardsC. Ethernet frame according to header information for forwarding the second floorD. Layer 2 Ethernet switch is working in the data link layer



QUESTION 58The following is a correct statement of the spanning tree:

A. Adoption of the physical path redundancy to improve the reliability of the network bridgeB. Adoption of the logical path redundancy to improve the reliability of the network bridge

C. to eliminate bridging by blocking the links may exist in the network path loopD. when the current active path fails to restore active redundant network connectivity link



QUESTION 59The following statement on the STP is not correct

A. a switched network can have only one designated switchB. All switch ports are root portC. root switch ports are designated ports for allD. switching network switches the switch priority value as the smallest non-root switch



QUESTION 60STP protocol bridge ID consists of two parts, namely,

A. bridge priorityB. The port ID bridgeC. The MAC address of bridgeD. The IP address of the bridge



QUESTION 61STP bridge ID in agreement with () bits

A. 8B. 32C. 48D. 64



QUESTION 62The following description of the principle of spanning tree protocol is correct

A. From all the switches in the network, select a switch as the root (Root)B. Calculate the switch to the shortest path to the root switchC. For each LAN, elect the root switch from the recent switch as the designated switch that is responsible for

forwarding this data on the LAND. non-root switch will choose the number of root port, the root port switch gives the path to the root switch is

the best path set



QUESTION 63In the STP protocol, which of the following factors will affect the election of the root switch?

A. switch priorityB. switch port IDC. switch interface bandwidthD. MAC address of switchE. the IP address of the switch



QUESTION 64The following description of the advantages and disadvantages of spanning tree protocol is not correct

A. Spanning Tree Protocol to manage redundant linksB. Spanning Tree Protocol to block redundant links, to prevent the generation of loopC. Spanning Tree Protocol to prevent the temporary loss of network connectivityD. Spanning Tree Protocol will enable Ethernet switch can work in the presence of physical loops in the

network environment



QUESTION 65Site A and Site B, respectively, and two ports connected to the switch, assuming that Site B does not send anymessages, then site A to site B to send the first data packet, the following statements is correct

A. switch MAC address table cannot be found in site B of the destination port, it will discard the packet.B. Site B switch to learn the address and message in the Site B to connect the port to send out

C. A switch to learn the site's address and broadcast packet out all ports fromD. A switch to learn the site's address and port to receive packets from the outside in addition to other

broadcast out all ports



QUESTION 66STP on the following statements is correct is

A. A switched network can have only one root switchB. All switch ports are root root portC. root switch ports are designated ports for allD. switching network switches the switch priority value becomes the root switch minimum



QUESTION 67In the STP, the switch port's role can be

A. Root portB. backup root portC. optional portD. Preliminary portE. Designated port

Correct Answer: ADESection: (none)Explanation


QUESTION 68RSTP STP in terms of which were improved

A. A non-root switch to elect a new root port, if the previous root port is no longer in the Forwarding state, andspecify the port has begun forwarding the upstream data, the new root port to the forwarding stateimmediately

B. When a switch port configured as an edge port, the port was once enabled, the port immediately become adesignated port (Designated Port), and enter the forwarding state

C. If you specify a port connected to multipoint link, the device can shake hands with the downstreamequipment to get the response immediately after entering the forwarding state

D. If you specify a port connected point to point link, the device can shake hands with the downstreamequipment to get the response immediately after entering the forwarding state



QUESTION 69Shortcomings have a single spanning tree

A. single spanning tree may lead to the same VLAN on the switch located on different hosts cannotcommunicate

B. In the single-spanning conditions, traffic cannot be shared on a different linkC. Run a single spanning tree, the whole network converges more slowlyD. In the single-spanning conditions, there may be sub-optimal path to the second floor



QUESTION 70In the RSTP standard, and not directly connected to a terminal connected to the other bridge port is defined as(), such port can directly enter the forwarding state, without any delay.

A. Fast portB. backup portC. Root portD. Edge port



QUESTION 71STP / RSTP is based on the port, and MSTP is based on () and.

A. root bridgeB. Specify the bridgeC. Root portD. Example



QUESTION 72RSTP protocol when specifying the port in case of failure, () will be quickly converted to the new delay to the

specified port is not forwarding state.

A. Forwarding PortB. Alternate PortC. Backup PortD. Edge Port



QUESTION 73RSTP protocol when the root port in case of failure, () will be quickly converted to the new root port is no delayto the forwarding state.

A. Forwarding PortB. Alternate PortC. Backup PortD. Edge Port



QUESTION 74Accordance with the definition of IEEE802.1Q, identify different VLAN tag is in what position

A. is not fixedB. source MAC address and destination MAC address beforeC. the source MAC address and destination MAC addressD. MAC address of the source and destination MAC address of the middle



QUESTION 75A switch supports 802.1Q protocol, which supports up to () a VLAN.

A. 512B. 1024C. 2048D. 4096E. theoretically support an unlimited number of

Correct Answer: D



QUESTION 76VLAN Yes () initials

A. virtual local area networkB. virtual long area networkC. virtual local area networkingD. virtual long area networking



QUESTION 77Vlan tag which is a layer of the OSI reference model implementation




QUESTION 78In an Ethernet switched network environment, which of the Ethernet frame formats?

A. is not tagged frames (ungtagged frame)B. Token frameC. The frame with the tag (tagged frame)D. FDDI frame



QUESTION 79GVRP VLAN Registration is general agreement that it is () of an application

A. GMRP

B. GMTPC. IGMPD. G, A, R, P



QUESTION 80In the S series switch, VLAN which can use the undo command to delete

A. vlan 1B. vlan 2C. vlan 1024D. vlan 4094



QUESTION 81In order to achieve the VLAN interface on the network layer functions, need to configure a VLAN interface

A. IP addressB. MAC addressC. Subnet MaskD. IP Prefix



QUESTION 82A switch configured vlan 3/4/5, trunk port GVRP protocol is not hired, and now receive a vlan 6 port Trunkpacket, the switch

A. This message will be flooded to all VLAN.B. Place the packet in flooding to VLAN1C. This packet will be flooded to all trunk portsD. discards the packet



QUESTION 83In the VRP platform, the command "interface vlan-interface vlan-id" What is the role

A. generating a VLANB. generates or enter a VLAN interface viewC. VLAN to a port configurationD. No such command



QUESTION 84A VLAN can be seen as a

A. collision domainsB. broadcast domainC. Management DomainD. blocking domain



QUESTION 85VLAN tag length () bytes.

A. 2B. 3C. 4D. 5



QUESTION 862-byte Ethernet frame header TPID, when the value of 0x8100 indicates that this is a carry () tagged frames.

A. 802.1PB. 802.1QC. 802.1DD. 802.1S



QUESTION 87Ethernet into VLAN feature, the port is divided into several types ().

A. Acess PortB. Trunk PortC. Hybrid PortD. None Port



QUESTION 88Judge: Trunk port sent to the peer device must be tagged frame.

A. TrueB. False



QUESTION 89Ethernet into VLAN feature, VLAN isolation of ().

A. two-story single multicast domainB. layer broadcast domainC. Layer 2 multicast domainD. MAC address of the second floor



QUESTION 90The traffic between different VLAN cannot communicate directly, you need to use ().

A. Port IsolationB. MAC visitsC. VLAN routing

D. VLAN switching



QUESTION 91Forward frame by checking the Ethernet packets carrying VLAN tag, if the port (), can determine whether theEthernet frame is forwarded from the port.

A. allow the labelB. The default PVIDC. MAC address of the correspondingD. STP disable state



QUESTION 92Using VLAN tagging, in exchange the network environment, the Ethernet frame has the followingtwo formats: () and ().

A. untagged frameB. tagged frameC. row frameD. column frame



QUESTION 93VLAN tag in the frame control information TCI (Tag Control Information) field include ().

A. PriorityB. CFIC. VLAN IdentifierD. TPID



QUESTION 94CFI field is 1bit, characterized by ().

A. Ethernet frame priorityB. Information bit sequenceC. bridge priorityD. port priority



QUESTION 95IEEE organizations to develop a () standard, standardized method of VLAN across switches to achieve

A. 802.1xB. 802.1dC. 802.1qD. 802.3



QUESTION 96All Ethernet frames within the switch are in () in the form of movement.

A. BPDUB. PVIDC. untagged frameD. tagged frame



QUESTION 97Switch port-based VLAN ID value, if the switch receives untagged frames, VLAN ID of the value depends on ().

A. BPDUB. PVIDC. MAC mapping tableD. IP address


Explanation


QUESTION 98ways to achieve the following configuration of the switch trunk port ethernet0 / 1 by adding VLAN 4().

A. [Switch] vlan 4[Switch-vlan4] port ethernet 0 / 1

B. [Switch] vlan 4[Switch-Ethernet0 / 1] port trunk pvid vlan 4

C. [Switch] vlan 4[Switch-vlan4] port trunk ethernet 0 / 1

D. [Switch] vlan 4[Switch-Ethernet0 / 1] port trunk permit vlan 4



QUESTION 99GVRP must open and close ports in the () port operations.

A. HybridB. AccessC. TrunkD. routed



QUESTION 100Gvrp command to enable GVRP. undo gvrp command to disable GVRP. By default, GVRP is ().

A. openB. offC. VLAN operation on the lastD. Any state



QUESTION 101Gvrp command on the following statements is correct ().

A. In the open port GVRP, you must first Enable GVRP globallyB. If the global GVRP is turned off, you can enable the port to change the state of GVRPC. Global GVRP is disabled, the port GVRP must also offD. is on or off the global GVRP GVRP operation in system view command



QUESTION 102Ethernet subinterface IP address must be configured before ()

A. MAC addressB. VLAN encapsulationC. Global GVRPD. port GVRP



QUESTION 103Definitions for the Ethernet sub-interface 0/1.1 VLAN100 members use the following configuration commands

A. [Router-Ethernet0/1.1] vlan trunk vid 100B. [Router-Ethernet0/1.1] port dot1q vid 100C. [Router-Ethernet0/1.1] vlan dot1q vid 100D. [Router-Ethernet0/1.1] vlan default vid 100



QUESTION 104With three switches to achieve inter-VLAN communication, create the VLAN interface view into the VLANconfiguration command ().

A. interface vlan-interface PVIDB. Interface vlan-interface VLAN-IDC. interface vlan-interface permit VLAN-IDD. interface vlan-interface trunk VLAN-ID



QUESTION 105Below that of a technology can reduce the scope of broadcast domains

A. VLANB. TrunkC. RARPD. STP



QUESTION 106VLAN-based classification methods are common

A. Port-based VLAN classificationB. MAC address-based VLAN classificationC. Protocol-based VLAN classificationD. VLAN based on the TCP port numbers



QUESTION 107Connect the switch and the link is called an ordinary PC

A. Access LinkB. Trunk linksC. Hybrid LinkD. ISL link



QUESTION 108On the access port following statements is correct

A. access port can belong to a VLANB. access port belongs to VLANC. access port is generally used to connect the user's computer port

D. access port is generally used to connect between the switch port



QUESTION 109Trunk port on the following statements is correct

A. trunk port can belong to a VLANB. trunk port belongs to VLANC. trunk port is generally used to connect the user's computer portD. trunk ports between switches are generally used to connect the port



QUESTION 110Following a protocol that can dynamically register VLAN information

A. GVRPB. GMRPC. VRRPD. STP



QUESTION 111VLAN-tagged frame than the more standard Ethernet frame () bytes

A. 4B. 32C. 12D. 8



QUESTION 112Site A and Site B, respectively, and two ports connected to the switch, then site A to site B, first send a data

packet, the following statement which is correct

A. switch to learn the address of A.B. Switch to learn the address of BC. The switch does not learn any addressD. A and B switch at the same time learn the address of



QUESTION 113The following description of a VLAN interface on the correct option

A. If an IP address to give the VLAN configuration, you need to create a virtual interface for this VLANB. two on the same switch VLAN interface can be configured the same IP addressC. Configure the virtual interfaces command with the VLAN ID number must be the sameD. For the VLAN cannot create a virtual interface configuration



QUESTION 114Access type of port to send packets ().

A. Send the message with tagB. stripping the VLAN information packet, send out directC. VLAN switching packets of information, then send outD. marked the PVID of the port information



QUESTION 115Trunk types of ports in the packet received untag time ().

A. Direct discardedB. with the port trunk VLAN ID information, and then sentC. Do not add tag information sent directlyD. marked the PVID of the port information, then send out



QUESTION 116Trunk type of port receives a packet with a tag, the following statements is correct ().

A. determine whether the port is allowed by the VLAN tag, the dataB. direct pass through without any processingC. If the port is not allowed by the VLAN tag, data, and discardedD. marked the PVID of the port information, then send out



QUESTION 117Trunk type of port to send packets, the following statements is correct ().

A. To send a message to the VLAN ID and port PVID different, then sent directlyB. To send a message to the VLAN ID and port the same as the PVID, the VLAN information is stripped, and

then sendC. will send packets to the VLAN ID and port the same as the PVID is sent directlyD. packets to be sent and the port's PVID VLAN ID is different from the VLAN information is stripped, and then

send



QUESTION 118The type of port on the Hybrid, the following statements is correct ().

A. Hybrid port can be used to switch the connection between the switch and the user can also be used for theconnection between the PC

B. Hybrid Trunk port in the port and receive data, the processing method is the sameC. Hybrid Trunk port port and main differences are, Hybrid port can allow multiple VLAN packets without tags,

but a trunk port only allows the default VLAN packets without tagsD. Hybrid port untag configured to send messages only when the work, no need to consider when receiving

messages



QUESTION 119To achieve inter-VLAN communication, the following statements is correct ().

A. In the L3 switch, can only be achieved through the router configuration arm inter-VLAN traffic routingB. the L2 switch, router configuration arm only through the inter-VLAN routing the communication toachieveC. In the L3 switch, VLAN interfaces can be configured to achieve three inter-VLAN communicationD. In the L2 switch, VLAN interfaces can be configured to achieve three inter-VLAN communication



QUESTION 120About the advantages of the following statements is correct VLAN is ().

A. VLAN on the switch by reducing the required number of physical ports to reduce network overheadB. VLAN by identifying the right to access to sensitive user data and applications to enhance network securityC. VLAN and flow control by adjusting the window size to improve network performanceD. VLAN network into smaller logical networks, which reduces the sensitivity of the network for broadcast

storm



QUESTION 121VLAN tag contains () data bits used to identify the VLAN a frame belongs

A. 4B. 32C. 12D. 8



QUESTION 122Frame marker will add to each frame (), so the frame can switch between the trunk port transmission.

A. Destination MAC addressB. source MAC address switchC. VLAN IDD. switch bridge ID



QUESTION 123Switch the default configuration in VLAN configuration has the following characteristics ().

A. The default VLAN cannot be manually deletedB. By default, all switch ports are members of the default VLAN portC. You must create the default VLAN, the port can be assigned to itD. The IP address configured on the switch will only be applied to a member of the default VLAN port



QUESTION 124In the VRP, VLAN tag field in the fixed value of TPID

A. 0x8100B. 0x0800C. 0x0806D. 0x9100



QUESTION 125As opposed to traditional LAN technology, VLAN has the following advantages:

A. Reducing the cost of moving and changingB. separate broadcast domains, inhibit the broadcast messageC. Strengthening the security of communicationsD. enhancing network robustness



QUESTION 126Originally part of a switch port VLAN 5, now with the undo vlan 5 command to delete VLAN 5, afterwhich the port belongs to VLAN

A. 0B. 1

C. 1023D. 1024



QUESTION 127GVRP protocol in () operation on the port

A. TrunkB. AccessC. hybridD. Normal



QUESTION 128Enable GVRP globally, after all the ports on the switch are automatically open the GVRP

A. TrueB. False



QUESTION 129The following description of GARP protocol options in the wrong

A. GARP protocol is the same at a switching network between members of the exchange offer distribution,information dissemination and as a means of registration of a

B. In the working mechanism of GARP, the property is through the "Registration Statement ---- ---- Statement"in the process spread to the entire network.

C. GARP protocol called Generic Attribute Registration ProtocolD. GARP GVRP protocol is only an application



QUESTION 130

In the system view, is a port needs to be allocated to a particular VLAN, including the operation to be performed

A. Create (or into) VLAN viewB. to a VLAN broadcast storm suppression ratioC. for the specified VLAN or VLAN interface description stringD. Ethernet port to a VLAN



QUESTION 131Switch-A and Switch-B are configured separately in the R & D department, sales department, productdepartment, the Ministry of Finance and Personnel in the VLAN port. Each VLAN contains 20 users. At least thenumber of subnets to route between all VLAN connectivity ().

A. 5B. 20C. 50D. 100



QUESTION 132The network administrator is removed from the switch more than one VLAN. When the administrator enters theundo vlan 1 command, you receive an error message. Error message occurs because the ().

A. VLAN can only be created by its users to deleteB. Only the roles assigned to VLAN 1 to other VLAN, VLAN 1 in order to removeC. The command is not entered correctly, resulting in a syntax errorD. VLAN 1 is the default management VLAN, cannot be removed



QUESTION 133VLAN grouping method, called the IP address-based grouping () of the VLAN.

A. PortB. RoutingC. MAC addressD. Strategy



QUESTION 134Switch access port belongs to VLAN ().

A. The only VLAN definedB. Maximum number of VLAN.C. all VLAND. The lowest numbered VLAN.



QUESTION 135Building A network administrator wants to divide the host, respectively, and VLAN 5 to VLAN 3, the followingstatement on the VLAN configuration is correct ().

A. VLAN information is automatically saved in the startup configurationB. manually create VLAN 3 and VLAN 5, the default VLAN automatically canceledC. The network administrator can view the global to create a VLAN or VLAN viewD. can be named BUILDING_A two VLAN to the other and in different geographical distinction between VLAN



QUESTION 136when delete a VLAN, the following statements is correct ().

A. Members of the VLAN port becomes non-active stateB. When there is VLAN routing interfaces (Vlanif interface), you must first delete the corresponding Vlanif be

deleted after the VLAN interfacesC. The network administrator can view the global delete VLAN or VLAN viewD. must be a member of the VLAN port assignments to other VLAN, you can delete the original VLAN



QUESTION 137Switch port is configured as a trunk port, now a host to be used to connect to the port to access the network.

The following operation is essential ()

A. In a global view to delete more than one VLAN on the portB. In the interface view, delete more than one VLAN on the portC. Close the interface and then re-enable to restore the default configurationD. Configure the interface to an access port



QUESTION 138Command port trunk permit vlan all what effect ().

A. This allows all of the VLAN on the port byB. The port is connected with the peer port must be configured port trunk permit vlan allC. peering devices can dynamically determine who is allowed by the VLAN IDD. If equipped with remote devices connected to port default vlan 3 commands, the VLAN 3 between the two

devices cannot communicate



QUESTION 139When you create a VLAN, the following statements is correct ().

A. Members of the VLAN port becomes active state immediatelyB. When you create VLAN routing interfaces (Vlanif interface), you must first create the corresponding VLAN

interfaces to create the appropriate VlanifC. The network administrator can view the global to create a VLAN or VLAN viewD. must be a member of the VLAN port assignments to other VLAN, the original VLAN can be created



QUESTION 140A switch part of the information displayed below, then the port's PVID is[Quidway] display interface Ethernet 1/0/1Mdi type: autoPort link-type: accessTagged VLAN ID: noneUntagged VLAN ID: 5

A. 0B. 1

C. 5D. lack of information, unknown



QUESTION 141Which of the following types of VLAN pass-through port allows?

A. TrunkB. AccessC. HybridD. Normal



QUESTION 142A Trunk port to allow VLAN 3 / 4 / 5 through, but only VLAN3 / 4 packet is with the tag, vlan5 packets withouttag, this may be because

A. The PVID of port 5B. The port's PVID of 3 and 4C. Trunk port in the configuration set up "port trunk permit vlan 3 4", but does not include VLAN5D. In the GVRP enabled on port



QUESTION 143About Access-Link, the right is described below:

A. When the Access Port receives the frame, if the frame does not contain 802.1Q tag header, the port will bemarked with the PVID

B. When the Access Port receives the frame, if the frame contains the 802.1Q tag header in the VLAN ID andport PVID inconsistent, then change the tag for the PVID in the VLAN ID

C. When the Access port transmits a frame, stripping 802.1Q tag header, sent as an ordinary Ethernet frameframe

D. When the Access port transmits a frame, to retain 802.1Q tag header, with a tag issued by the Ethernetframe to frame

Correct Answer: ACSection: (none)

Explanation


QUESTION 144On Trunk port, right is described below:

A. When a Trunk port receives frames, if the frame does not contain 802.1Q tag header, the port will bemarked with the PVID Trunk port when receiving a frame if the frame contains the 802.1Q tag header, notchange

B. When a Trunk port transmits a frame, when the frame with the port's PVID VLAN ID is not the same, passdirectly through

C. When a Trunk port transmits a frame, when the frame of the PVID of the port VLAN ID and the same is notoperating on the tag



QUESTION 145In order to ensure that all hosts belong to the same VLAN can receive broadcast destined for this VLANpackets, the switch must forward operation which follows

A. The switch from the packet sent to all portsB. transmits the packet to the switch with the other ports in a VLANC. transmits the packet to the switch allows all of the VLAN trunk link throughD. transfer packets from the switch to send out all the roads link



QUESTION 146The following statement is true about the VLAN is ().

A. The default switch configuration VLAN configuration VLAN 1 cannot delete or renameB. switch can support up to 255 VLANC. allows a single multiple VLAN access portD. Allowing the same time more than one VLAN trunk port to a single



QUESTION 147VRRP name is:

A. Virtual Routing Redundancy ProtocolB. Virtual Router Redundancy ProtocolC. Virtual Redundancy Router ProtocolD. Virtual Redundancy Routing Protocol



QUESTION 148The following statement is correct about VRRP is:

A. Only Master processing the data sent to virtual router;B. Only Slave processing the data sent to virtual router;C. Master and Slave can be sent to the same virtual router handle the data flow and can be shared;D. Default Only Master processing the data sent to virtual router can be configured to open the Slave process

sent to the same virtual router function of the data



QUESTION 149VRRP on the network, the following on the PC on the network, configure the default gateway is correct to say:

A. PC machines only configure a default gateway, default gateway address the IP address for the MasterB. PC machines only configure a default gateway, default gateway address for the virtual router's IP addressC. PC machines configured with two default gateways, IP address, respectively, the Master and Slave IP

addressD. PC machines configured with three default gateway IP address are Master, Slave IP address and virtual

router's IP address



QUESTION 150Below on the VRRP virtual IP address is correct to say:

A. A virtual router can only be associated with a virtual IP address;B. A virtual router associated with up to three virtual IP address;C. a virtual router can be associated with multiple virtual IP addresses, but at the same time only one is

available;D. A virtual router can be associated with multiple virtual IP addresses, virtual IP addresses the same time they

are available.



QUESTION 151The following statement is true about the role of VRRP is:

A. VRRP improves the reliability of the network default gateway;B. VRRP routing protocols to speed up network convergence speed;C. VRRP is mainly used for network traffic share;D. VRRP for different network segments with a default gateway, simplifying the network gateway on the PC

configuration.



QUESTION 152In configuring VRRP, you can configure the VRRP Priority range is

A. 0-127B. 0-255C. 1-127D. 1-254



QUESTION 153The following statement on the VRRP Priority right in is:

A. No matter how much the configuration of the Priority, the virtual IP address of the owner to always use 255as a Priority

B. Priority no matter how much the configuration of the virtual IP address of the owner always use 0 as aPriority

C. You can configure VRRP router to a table the way Priority 0 so that the Master VRRP router does notparticipate in the election, so that the router is always a Slave

D. When the Master VRRP VRRP router to stop running when the network will send a Priority 0 VRRPadvertisement messages



QUESTION 154RTA using Ethernet0 / 0 interface to connect to a LAN port IP address is 10.1.1.251, netmask 255.255.255.0.Asked the RTA to create a virtual router, ID is 1, the virtual IP address is 10.1.1.254, the following command iscorrect:

A. [RTA-Ethernet0 / 0] vrrp vrid 1 virtual-ip 10.1.1.254B. [RTA] vrrp vrid 1 virtual-ip 10.1.1.254C. [RTA-Ethernet0 / 0] vrrp vrid 1 virtual-ip 10.1.1.254 mask 255.255.255.0D. [RTA] vrrp vrid 1 virtual-ip 10.1.1.254 mask 255.255.255.0



QUESTION 155RTA's Ethernet0 / 0 and the RTB Ethernet0 / 0 connected to the same LAN and turn VRRP, while creating avirtual router, ID is 1, the virtual IP address is 10.1.1.254. RTA's Priority of 200, RTB'sPriority is the default. In the RTA there are configured as follows:[RTA-Ethernet0 / 0] vrrp vrid 1 track Ethernet 1 / 0 reduced 150The following description is correct:

A. When the RTA detected Ethernet1 / 0 fails, RTA will become the priority of 150B. When the RTA detected Ethernet1 / 0 fails, RTA priority becomes 50C. When the RTA detected Ethernet1 / 0 fails, RTB will become the priority of 150D. When the RTA detected Ethernet1 / 0 fails, RTB will become the Master



QUESTION 156RTA's Ethernet0 / 0 and the RTB Ethernet0 / 0 connected to the same LAN and turn VRRP, while creating avirtual router, ID is 1, the virtual IP address is 10.1.1.254. RTA's Priority of 200, RTB's Priority is the default. Onthe RTB with the command display vrrp interface Ethernet 0 / 0, see:...Preempt: YES Delay: 5...The following description of the above information is correct:

A. When the RTB found his higher priority than the RTA will immediately seize the RTA as MasterB. When the RTB found his higher priority than the RTA will not seize the RTA as MasterC. When the RTB found his higher priority than the RTA will seize the RTA in 5 seconds as MasterD. When the RTB find themselves lower priority than the RTA will seize the RTA in 5 seconds as Master



QUESTION 157The following statement on the Master VRRP election is correct:

A. Priority greatest configured as MasterB. Priority smallest configuration of a SlaveC. Configure the greatest is not necessarily a Master PriorityD. Priority smallest configuration is not necessarily a Slave



QUESTION 158RTA's Ethernet0 / 0 and the RTB Ethernet0 / 0 connected to the same LAN and turn VRRP, while creating avirtual router, ID is 1, the virtual IP address is 10.1.1.254. Priority without modifying the case of the RTA, RTBdoes the following command to make a Master are:

A. [RTB-Ethernet0 / 0] vrrp vrid 1 priority 200B. [RTB-Ethernet0 / 0] vrrp vrid 1 virtual-ip 10.1.1.254 priority 200C. [RTB-Ethernet0 / 0] vrrp vrid 1 force-masterD. [RTB] vrrp vrid 1 force-master



QUESTION 159The following statement is true on the virtual router is:

A. number of routers in the same virtual router ID is the router configuration associated to the same virtualrouter;

B. multiple routers in the same virtual IP address configuration means that the router associated to the samevirtual router;

C. If you want to associate more than one router to the same virtual router, virtual router ID and virtual IPaddress configuration must be identical;

D. If you want to associate more than one router to the same virtual router, virtual router ID and at least onevirtual IP address configured the same.



QUESTION 160HDLC is an ISO standard link layer protocol used to encapsulate asynchronous serial data link.

A. TrueB. False



QUESTION 161HDLC frame is divided into three types, namely,

A. Control of the frame (C frame)B. Monitoring the frame (S frame)C. Information frames (I frames)D. unnumbered frame (U frame)



QUESTION 162HDLC what are the characteristics

A. Full-duplex communication, can be continuously transmitted without waiting for confirmation of data, ahigher transmission efficiency of data link

B. All frames are used CRC checksum, sequence number of information frames to prevent revenue leakageor re-entry, high transmission reliability

C. transmission control functions and processing functions separated, with greater flexibility and better controlD. agreement does not depend on any one character encoding set, data packets can be transparently



QUESTION 163VRP platform, set the Serial port on the type of data link layer encapsulation is HDLC command is

A. encapsulation hdlcB. link-protocol hdlcC. hdlc enableD. link-protocol ppp



QUESTION 164Judge: HDLC is a bit stream-oriented data link layer protocol, can be of different character sets of data aretransparent transmission can be achieved.

A. TrueB. False



QUESTION 165HDLC, which has several frame types ().

A. Information frameB. Monitoring frameC. Unnumbered frameD. frame retransmission



QUESTION 166HDLC frame not included in the monitoring of which field ().

A. Address Field (A)B. Control field (C)C. Information Field (I)D. Frame Check Sequence field (FCS)



QUESTION 167To determine: the standard HDLC protocol suite of protocols are running on synchronous serial lines above.

A. TrueB. False



QUESTION 168Judge: HDLC serial interface can be run through the ip address unnumbered interface LoopBack 0 commandto configure the IP address to share with LoopBack 0.

A. TrueB. False



QUESTION 169In HDLC, the mark the start and end frame fields for a fixed value, it is

A. 11111111B. 01111110C. 00000000D. 11111110



QUESTION 170To determine: the asynchronous response mode ARM (Asynchronous Response Mode) is a technology thatallows any node to initiate transfer of the operation.

A. TrueB. False



QUESTION 171HDLC method used for transparent transmission of bit-stream ().

A. bit stuffing techniqueB. Special CharactersC. Data Length fieldD. None of the above

Correct Answer: A



QUESTION 172Huawei VRP system router serial interface as the default package ().

A. HDLCB. PPPC. Frame RelayD. None of the above



QUESTION 173Loopback0 on a router, the IP address of 10.1.1.1/32, to borrow loopback0 in serial0/0/1 configurethe IP address of the command is

A. [Quidway] ip address serial0/0/1 equal loopback0B. [Quidway-serial0/0/1] ip address serial0/0/1 equal loopback0C. [Quidway] ip address unnumbered interface serial0/0/1 loopback0D. [Quidway-serial0/0/1] ip address unnumbered interface loopback0



QUESTION 174The following statement on HDLC, which is correct ().

A. on the system architecture in terms of, HDLC is only applicable to the structure of point to pointB. the work is concerned, HDLC for half-duplex or full duplexC. in terms of the transmission, HDLC only for synchronous transmissionD. The transmission rate considerations, HDLC commonly used in high-speed transmission



QUESTION 175HDLC field by which to identify the upper layer protocol ().

A. flag field

B. Address fieldC. Control FieldD. cannot be identified



QUESTION 176PPP support () authentication protocol, and therefore more secure than the HDLC

A. PAPB. MD 5C. CHAPD. SSH



QUESTION 177In the PPP protocol, PAP certification process required to establish () handshake

A. 2B. 3C. 4D. 1



QUESTION 178Standard PPP frame format protocol which includes several fields ()

A. Protocol fieldB. Information FieldsC. length fieldD. fill in the fields



QUESTION 179The following statement on the LCP, which is correct ().

A. is responsible for negotiating the establishment of linksB. Layer 3 protocol type negotiationC. will cut off the link after link idle timer timeoutD. Testing the link, link quality to determine whether the link can be established



QUESTION 180Judge: PPP protocol, IPCP negotiation process of dynamic and static, like consultation, only one Config-Request dialogue IP address assignment can be completed.

A. TrueB. False



QUESTION 181Frame Relay using the following method to dynamically address which is mapped to DLCI

A. ARP protocolB. RARP protocolC. inARP agreementD. map protocol



QUESTION 182In the frame relay network, the bandwidth of each virtual circuit for the control strategy is the correct description

A. In the Tc, the amount of data transfer when the user is not greater than Bc, to continue receiving the frametransmission

B. When the user data transmission is greater than Bc Bc and Be, but not greater than the sum, it will sendmore than frame the scope of Bc DE position "1"

C. When the Tc in the user data transmission is greater than the sum of Bc and Be, the frame will exceed thescope of the DE position "1"

D. When the Tc in the user data transmission is greater than the sum of Bc and Be, it will exceed the range offrames discarded



QUESTION 183Judge: In X.25, in a packet transmission path of each node must receive a complete packet and must becompleted before sending error checking. Frame Relay nodes simply check the destination address in thepacket header information, and immediately forward the packet.

A. TrueB. False



QUESTION 184AAL layer which several sub-sub-layer ().

A. TC sublayerB. PM sublayerC. Convergence Sublayer (CS)D. disassembly sublayer (SAR)



QUESTION 185The formation of the routing table a variety of ways, the following is the correct way ().

A. Static Routing ProtocolB. Dynamic routing protocolsC. Application layer protocolD. Transport Layer



QUESTION 186A router via RIP, OSPF, BGP and static routes are learning to reach the same destination address routing. Bydefault, VRP will eventually selected () routing as the optimal route

A. RIPB. OSPFC. BGPD. Static routes



QUESTION 187Routers do not need to know the full forward path, only know the destination of the nearest next hop how totake forward this packet relay process we call

A. hop by hop forwardingB. host by host forwardingC. router by router forwardingD. network by network forwarding



QUESTION 188The following commands configure a default route is correct:

A. [Quidway] ip route-static 0.0.0.0 0.0.0.0 172.16.2.1B. [Quidway] ip route-static 0.0.0.0 255.255.255.255 172.16.2.1C. [Quidway-Serial0] ip route-static 0.0.0.0 0.0.0.0 172.16.2.1D. <Quidway> ip route-static 0.0.0.0 0.0.0.0 172.16.2.1



QUESTION 189The following on in the network have the shortcomings of using static routing

A. In a large complex network configurationB. Network topology changes, you must re-configure a static routeC. Static routes cannot be known to the external router, resulting in poor network connectivityD. In the VRP, the static routing cannot achieve load sharing



QUESTION 190Received from a neighbor to send the Response packet, RIP routing protocol packets calculated item measure,measure the size is equal to ().

A. packets carry measureB. message containing the measure +1C. packets received carried the measure + measurement network packet overheadD. The network receives the message overhead of metrics



QUESTION 191The following statement on the RIP network size is correct

A. RIP is based on Bellman-Ford algorithm can correctly calculate the shortest path to large-scale networkB. RIP 16-jump limit is to prevent routing loops in the network resulting in infinite packet transmissionC. Even within the 16 hop limit, for more complex network topology, it is recommended that you do not select

the choice of RIP and other routing protocols OSPFD. only fit in a small network running is a major cause RIP to periodically broadcast their full routing

information, routing within large networks are more items of information, which take up too much networkbandwidth caused by RIP



QUESTION 192When the interface runs in the RIPv2 broadcast mode, it can receive a packet

A. RIPv 1 broadcast packetsB. RIPv 1 multicastC. RIPv 2 broadcast packetsD. RIPv 2 multicast



QUESTION 193In the PPP protocol, you need three-way handshake authentication protocol, it is only transmitted on thenetwork without sending the user name is password authentication protocol

A. PAPB. CHAPC. MD 5D. TCP



QUESTION 194In the PPP agreement, the PAP and CHAP authentication is correctly described

A. PAP authentication requires three-way handshakeB. CHAP authentication requires two-way handshakeC. PAP authentication information sent using clear text authenticationD. CHAP authentication information sent using clear text



QUESTION 195Following that command is to set the PPP authentication PAP

A. ppp papB. ppp chapC. ppp authentication-mode papD. ppp authentication-mode chap



QUESTION 196Router A is configured as follows:[RTA] aaa[RTA-aaa] local-user huawei password cipher hello[RTA-aaa] local-user huawei service-type ppp[RTA] interface Serial 0[RTA-Serial0] link-protocol ppp[RTA-Serial0] ppp authentication-mode pap[RTA-Serial0] ip address 10.1.1.1 30Router B is configured as follows:[RTB] interface Serial 0[RTB-Serial0] link-protocol ppp[RTB-Serial0] ppp chap user huawei

[RTB-Serial0] ppp chap password cipher hello[RTB-Serial0] ip address 10.1.1.2 30When two routers connected to Serial 0, the two routers can be connected to the peer.

A. TrueB. False



QUESTION 197Router A is configured as follows:[RTA] aaa[RTA-aaa] local-user huawei service-type ppp[RTA] interface Serial 0[RTA-Serial0] link-protocol ppp[RTA-Serial0] ppp authentication-mode pap[RTA-Serial0] ip address 10.1.1.1 30Router B is configured as follows:[RTB] interface Serial 0[RTB-Serial0] link-protocol ppp[RTB-Serial0] ppp chap user huawei[RTB-Serial0] ppp chap password cipher hello[RTB-Serial0] ip address 10.1.1.2 30When two routers connected to Serial 0, the two routers can be connected to the peer.

A. TrueB. False



QUESTION 198PPP protocol TCP / IP protocol stack layer at which ().




QUESTION 199Judge: PPP protocol, CHAP authentication process requires the interaction of three packets, respectively,

Challenge, Response, Success / Failure.

A. TrueB. False



QUESTION 200The following PPP protocol, which belong to NCP ().

A. IPv 6CPB. ICMPC. IPXCPD. TCP



Exam D

QUESTION 1PPP protocol work in the OSI seven layer model




QUESTION 2PPP connection is established, you can use which protocol component Echo-Request and Echo-Replymessage packet detect link status ().

A. Data PackageB. LCPC. NCPD. IPCP



QUESTION 3Judge: PPP provides a point-to multi-protocol data packets transmitted on the standard method, is widely usedpoint to point data link layer communication protocol.

A. TrueB. False



QUESTION 4PPP data frame cannot be directly transmitted on the link, link the different PPP data frames transmitted onadditional packages and require different control mechanisms. PPP serial link data transmission standardHDLC frame to follow.

A. TrueB. False

Correct Answer: A



QUESTION 5PPP connection is established, VRP platform default number of seconds to send every one Echo-Requestpacket ().

A. 1B. 5C. 10D. 60




QUESTION 6LCP negotiated parameters are usually what ().

A. MRUB. Authentication ProtocolC. Magic-numberD. IP address



QUESTION 7Judge: LCP in the magic-number field can be used for loop detection.

A. TrueB. False



QUESTION 8In the following configuration, the PAP protocol configuration keyword cipher user password is ().[RTB] interface Serial 0[RTB-Serial0] link-protocol ppp[RTB-Serial0] ppp pap local-user huawei password cipher hello[RTB-Serial0] ip address 10.1.1.2 30

A. Configure the password file using ciphertextB. authentication, data packets sent in the password ciphertextC. Both of the aboveD. None of the above two



QUESTION 9Network Control Protocol (NCP) can provide any functionality for PPP connections ().

A. Error CheckingB. AuthenticationC. carry multiple Layer 3 protocolsD. Congestion Control



QUESTION 10Judge: PPP protocol, CHAP authentication process requires three packets of the interaction. In order to matchthe request message and response message, the message contains Identifier field, a certification process usedby the packet use the same Identifier information.

A. TrueB. False



QUESTION 11On the PPP, the following description is correct

A. supports both synchronous links and asynchronous linksB. only supports synchronous linksC. only supports asynchronous links

D. None of the above



QUESTION 12PPP protocol field in the frame information field that indicates the type of protocol used, following which a valueused to represent the information domain is an IP packet

A. 0x0021B. 0x8021C. 0x8821D. 0x8863



QUESTION 13PPP protocol field in the frame information field that indicates the type of protocol used, following which a valueused to represent the information domain is an LCP packet data

A. 0x0021B. 0x8021C. 0xc021D. 0x8863



QUESTION 14in the PPP, when the communication of both ends of the physical line activation is detected, it will not beavailable from link to link establishment phase transition stage, at this stage is mainly through the () linkprotocol configuration parameters

A. IPB. DHCPC. LCPD. NCP



QUESTION 15PPP state transition diagram which includes the following stages

A. IdleB. EstablishC. AuthenticateD. Network



QUESTION 16In the PPP, when the physical layer cannot detect the carrier or the management of the link to shutdownoperations, which link will be broken, then it is in what stage

A. link is unavailable stageB. link establishment phaseC. Validation phase.D. Network layer protocol phase.



QUESTION 17Which of the following situations will result in termination of PPP link?

A. Authorization failedB. loss of carrier,C. Administrators people close linkD. link quality test failed



QUESTION 18PPP protocol defines which of the following components

A. Data packageB. Data EncryptionC. Link Control Protocol (LCP)D. Network Control Protocol (NCP)



QUESTION 19Router A is configured as follows:[RTA] aaa[RTA-aaa] local-user huawei password simple quidway[RTA-aaa] local-user huawei service-type ppp[RTA] interface Serial 0[RTA-Serial0] link-protocol ppp[RTA-Serial0] ppp authentication-mode pap[RTA-Serial0] ip address 10.1.1.1 30Router B is configured as follows:[RTB] interface Serial 0[RTB-Serial0] link-protocol ppp[RTB-Serial0] ppp pap local-user huawei password simple hello[RTB-Serial0] ip address 10.1.1.2 30When two routers connected to Serial 0, the two routers can connect to the remote

A. TrueB. False



QUESTION 20PPP supports dynamic address negotiation, the port on the IP address on port negotiation command isdynamic

A. [Quidway-Serial0] ip address negotiationB. [Quidway-Serial0] ip address ppp-negotiationC. [Quidway-Serial0] ppp negotiationD. [Quidway-Serial0] ppp ip-negotiation



QUESTION 21Judge: PPP protocol, IPCP uses the same mechanism for consultations and LCP, message type,but not calledIPCP LCP, but the work process, the same message and so on and LCP.

A. TrueB. False



QUESTION 22Judge: PPP protocol is an important feature to provide authentication, use the link at both ends can negotiatewhich authentication protocol and the implementation of the certification process, only the authentication issuccessful will establish a connection.

A. TrueB. False



QUESTION 23Which of the following statement is correct ().

A. LCP negotiation authentication informationB. CHAP packets through two interactive authenticationsC. IPCP can be used to negotiate IP, compression and other informationD. PAP is used for user authentication



QUESTION 24PPP protocol, CHAP encryption algorithm is used ().

A. DESB. MD 5C. AESD. do not use



QUESTION 25Judgment: In a PPP link, cannot transmit both IPv4 and IPv6 packets ().

A. True

B. False



QUESTION 26PPP for different network layer protocols have different network control protocol, such as

A. IPCPB. IPXCPC. MPLSCPD. SLIPCP



QUESTION 27PPP protocol mainly by the three protocols, namely

A. PPPOEB. LCP (Link Control Protocol)C. NCP (Network Control Protocol)D. PPP extension agreement



QUESTION 28PPP protocol address field is usually filled with content

A. 0x7EB. 0xFFC. 0xFED. 0x03



QUESTION 29MRU that the termination of PPP data frames received data field maximum, usually the default value for this

parameter option, which is () bytes.

A. 1492B. 1500C. 4700D. 9600



QUESTION 30In the PPP link establishment phase is the exchange of messages

A. IP packetsB. LCP packetsC. NCP packetsD. DHCP packets



QUESTION 31PAP authentication protocol, which has several types of data packets

A. Authenticate-RequestB. Authenticate-AckC. Authenticate-FailD. Authenticate-Nak



QUESTION 32PPP authentication fails, what will Authenticating phase to phase

A. IdleB. EstablishingC. NetworkingD. Terminating



QUESTION 33Router A is configured as follows:[RTA] aaa[RTA-aaa] local-user huawei password simple hello[RTA-aaa] local-user huawei service-type ppp[RTA] interface Serial 0[RTA-Serial0] link-protocol ppp[RTA-Serial0] ppp authentication-mode pap[RTA-Serial0] ip address 10.1.1.1 30Router B is configured as follows:[RTB] interface Serial 0[RTB-Serial0] link-protocol ppp[RTB-Serial0] ppp pap local-user huawei password simple hello[RTB-Serial0] ip address 10.1.1.2 30When two routers connected to Serial 0, the two routers can connect to the remote

A. TrueB. False



QUESTION 34In the PPP link establishment phase, the receiver receives data packets LCP code does not recognize, they willsend an LCP to the right side of () message

A. Code-Reject packetB. Protocol-Reject packetC. Field-Reject messageD. Code-NAK packets



QUESTION 35Judge: In the following configuration, configure the PPP connection, and the use of dynamically allocated IPaddresses. Link is created, the routing table will appear when the direct route 10.1.1.0/30 ().[RTB] interface Serial 0[RTB-Serial0] link-protocol ppp[RTB-Serial0] ip address 10.1.1.2 30[RTB-Serial0] remote address 10.1.1.1

A. TrueB. False



QUESTION 36PPP link Configuring TCP / IP header compression, through which the protocol negotiation ().

A. LCPB. PAPC. IPCPD. CHAP



QUESTION 37CHAP authentication protocol, which has several types of data packets

A. Challenge messageB. Request packetC. Response MessageD. Success messageE. Failure message

Correct Answer: ACDESection: (none)Explanation


QUESTION 38Judge: Serial port with two Quidway routers directly connected to the link layer protocol encapsulation to PPP,IP addresses are not the same at both ends of the link segment can exchange

A. TrueB. False



QUESTION 39Router A is configured as follows:[RTA] aaa[RTA-aaa] local-user huawei password cipher hello

[RTA-aaa] local-user huawei service-type ppp[RTA] interface Serial 0[RTA-Serial0] link-protocol ppp[RTA-Serial0] ppp authentication-mode chap[RTA-Serial0] ip address 10.1.1.1 30Router B is configured as follows:[RTB] interface Serial 0[RTB-Serial0] link-protocol ppp[RTB-Serial0] ppp chap user huawei[RTB-Serial0] ppp chap password cipher hello[RTB-Serial0] ip address 10.1.1.2 30When two routers connected to Serial 0, the two routers can connect to the remote

A. TrueB. False



QUESTION 40In the configuration of PPP PAP authentication, the following operation is necessary which

A. party to be validated user name and password added to the local user listB. Configure the device is connected with the end of the interface encapsulation type to PPPC. Set the authentication mode for PPP PAPD. was configured to verify the authenticator sends a user name and password



QUESTION 41What is the role the following command ().ip address ppp-negotiate

A. Turn on the client requests an IP address to the functionB. Open the request to accept the IP address of the remote functionC. Open the IP address assigned to the static functionD. None of the above



QUESTION 42PPP Maximum Receive Unit (Maximum Receive Unit, MRU) is the default number of bytes ().

A. 1024B. 1500C. 1518D. 8096



QUESTION 43In the PPP link establishment phase, the client sends the Configure-Request parameter value cannot beidentified in the local, which the client should respond to the message ().

A. Configure-NakB. Configure-RejectC. Configure-AckD. None of



QUESTION 44In network switching technology, circuit-switched telephone network based on the principle of circuit switching.The following description on the right is the circuit-switched

A. small delayB. transparent transmission, that transmission path of user data without any amendment or interpretationC. fixed share of the bandwidth, the high utilization of network resourcesD. be able to better ensure the quality of Qos



QUESTION 45In the VRP to configure Frame Relay sub-interface, optional interface type which sub-

A. P2PB. NBMAC. P2MPD. Broadcast



QUESTION 46Reverse Address Resolution Protocol (Inverse ARP) is the main function of

A. The network address of the device through the network to the device's hardware address lookupB. DLCI number to find the connectionC. Find the Frame Relay network to connect the virtual circuit protocol address of the remote deviceD. Frame Relay network in the remote protocol address to generate the mapping DLCI



QUESTION 47If the Frame Relay network has experienced a block of PVC, Frame Relay, a field through which theinformation circular source

A. CLPB. BECNC. FECND. TCP



QUESTION 48Frame Relay is only complete () function of the core layer, the flow control, error correction and other completeintelligent terminal leave, greatly simplifying the agreement between the node

A. link layer and network layerB. network layer and transport layerC. transport layer and session layerD. Physical layer and link layer



QUESTION 49Judge: Run the Frame Relay port, MAP table is a logical interface corresponding to different logical interfaceswith different MAP table.

A. True

B. False



QUESTION 50The user side of the host or terminal frame relay network interface ().

A. DTEB. DCEC. NNID. None of the above



QUESTION 51Judgment: When the package frame relay protocol, the default frame encapsulation format isIETF.

A. TrueB. False



QUESTION 52In the Frame Relay encapsulation on the interface to enable dynamic Address Resolution ProtocolReverse the order is ().

A. frame-realy reverse-arpB. frame-relay inarpC. inverse-arpD. reverse-arp



QUESTION 53Judge: Frame Relay X.25 protocol is a function of the third layer has been simplified, while providing

retransmission after errors found in operation.

A. TrueB. False



QUESTION 54Frame Relay data link layer in the work, provide the following functions

A. statistical multiplexingB. Frame TransparentC. Error DetectionD. retransmission operation



QUESTION 55Frame Relay LMI DLCI which of normally occupied

A. 0B. 16C. 1007D. 1023



QUESTION 56The following description of Frame Relay technology is the right

A. Frame Relay data link layer technology is used in a simplified way to transfer and exchange of data unitsfast packet switching technology.

B. Frame Relay only completed OSI physical layer and link layer core layer functionsC. Frame Relay to flow control, error correction and other complete intelligent terminal leave, greatly simplifying

the agreement between the node.D. Frame Relay uses virtual circuit technology, can make full use of network resourcesE. Frame Relay has a high throughput, low latency for unexpected business and so on.

Correct Answer: ABCDESection: (none)

Explanation


QUESTION 57Frame Relay, virtual circuit VC (Virtual Circuit) is established between two network devices in the logic circuit.According to established methods, virtual circuits can be divided into

A. Static Virtual Circuit SVC (Static Virtual Circuit)B. Temporary virtual circuit TVC (Temporary Virtual Circuit)C. PVC PVC (Permanent Virtual Circuit)D. SVC SVC (Switching Virtual Circuit)



QUESTION 58To include the router's frame relay network 12 to achieve full interconnection topology, how many of the PVC

A. 6B. 132C. 66D. 12



QUESTION 59Frame Relay and X.25 in common is that

A. are based on the virtual circuitB. packet switching technology isC. is only the second layer protocolD. support congestion detection, confirmation retransmission, flow control mechanisms



QUESTION 60Frame Relay congestion avoidance can be achieved is determined by which of several header fields to achieve

A. BECN

B. FECNC. DLCID. DEE. CIR



QUESTION 61On the data link connection identifier DLCI, the following description is correct

A. Frame Relay in a single physical transmission line to provide multiple virtual circuits, virtual circuit is adifferent DLCI to distinguish between the

B. DLCI only in the local interface and directly connected to the end of the interface effective, does not havethe overall effectiveness of the

C. In the Frame Relay network, the different physical interfaces on the same DLCI that is a virtual connectionwith

D. Frame Relay network user interface supports up to 1024 virtual circuits, the DLCI range is available to theuser 16 to 1007



QUESTION 62Huawei router configuration on frame relay network, the use of Inverse ARP protocol, you cannot manuallyconfigure a static address mapping, because the Inverse ARP protocol address mapping can be dynamicallygenerated

A. TrueB. False



QUESTION 63In the Frame Relay encapsulation on the interface to enable dynamic Address Resolution Protocol Reversecommand is

A. frame-relay inarpB. frame-realy reverse-arpC. inverse-arpD. reverse-arp

Correct Answer: A



QUESTION 64In the configuration command fr map ip 10.1.1.2 200, the number 200 is the meaning of

A. Logical channel number on the sideB. local DLCI numberC. number of side interfaceD. Number of end nodes



QUESTION 65If the router is enabled Frame Relay PVC switching, frame relay interface type should be

A. DTEB. DCEC. NNID. UNI



QUESTION 66Judge: Frame Relay multipoint subinterfaces can remotely via a PVC to connect multiple nodes.

A. TrueB. False



QUESTION 67The following statement on which Frame Relay is correct ().

A. DLCI only in the local interface and directly connected to the terminal interface to the effectiveB. PVC is only in the virtual connection between the DCEC. Frame Relay address mapping table is stored inside the next hop IP address and the DLCI mapping

D. Reverse Address Resolution Protocol IP can be obtained through the end of the corresponding DLCI



QUESTION 68The following configuration command in Frame Relay represents what the meaning of 30 ().[RTB-Serial0] fr map ip 10.1.1.2 30

A. maskB. DLCIC. CostD. Weight



QUESTION 69in the frame relay network, the Local Management Interface LMI (Local Management Interface) protocolrequest message through the state and status messages to maintain the link state and Frame Relay PVCstatus, including

A. Record increase in PVC.B. Remove the PVC has been broken recordC. PVC state change monitoringD. Link integrity verification



QUESTION 70In the VRP system, Frame Relay LMI protocol support package for

A. Q933aB. AnsiC. CiscoD. Nonstandard



QUESTION 71Which of the following are the parameters of Frame Relay?

A. CIR Committed Information RateB. TTL Time to LiveC. BE allowed to exceed the amount of emergencyD. B, C committed burst amount



QUESTION 72The following features are not part of Frame Relay

A. Cell length of fixedB. is an international standardC. Simplification of the X.25 Layer 3 functionalityD. complete statistical multiplexing at the link layer, a transparent frame transmission and error detection



QUESTION 73In the frame relay network, bandwidth control parameter description on the right is

A. CIR is a network user with the user information transfer rate agreement that committed information rateB. Bc network to allow users to rate CIR Tc interval in the amount of data transferred, their relationship is Tc =

Bc / CIRC. Be in the network to allow users to transmit time interval Tc more than the amount of data BcD. If the user is less than the rate of transmission of information equal to CIR, should ensure that this part of

the transmission of information



QUESTION 74The following narrative on the right is the DLCI

A. DLCI has only local significanceB. DLCI is assigned by the DCE side of theC. DLCI range is available to the user 16-1007D. different physical interfaces can be configured the same DLCI



QUESTION 75Quidway routers to check on the serial s0 / 1 operates in DTE or DCE mode, which should use the followingcommand

A. display controller serialB. display saved-configC. display interface s0 / 1D. display current-config



QUESTION 76Statically configured in the Frame Relay encapsulation must be specified which parameters MAP

A. The local DLCIB. DLCI on the sideC. The protocol address of the localD. The end of the protocol address



QUESTION 77Frame Relay frame under which the field does not contain

A. BECNB. FECNC. CIRD. DLCIE. PVC

Correct Answer: CESection: (none)Explanation


QUESTION 78

VRP, the Frame Relay encapsulation support () format

A. IETFB. ANSIC. Q.933aD. Nonstandard



QUESTION 79In the Quidway router, which command can be used to display the network address and the DLCI mapping

A. display fr interfaceB. display frC. display fr map-infoD. display fr brief



QUESTION 80Quidway routers configured in a Frame Relay PVC, found no effect, what possible reason is

A. In the same router configured with the same number dlciB. LMI type configuration errorC. Frame Relay encapsulation type of configuration errorD. DLCI configuration error



QUESTION 81Judgement: The following Frame Relay command results display the IP address 10.1.1.2 is the local IPaddress.[RTA] dis fr map-infoMap Statistics for interface Serial0 (DTE)DLCI = 100, IP INARP 10.1.1.2, Serial0create time = 2007/06/04 17:34:59, status = ACTIVEencapsulation = ietf, vlink = 20, broadcast

A. TrueB. False



QUESTION 82As the distance vector routing protocol uses split horizon mechanism, will lead to the end of the frame relay toconnect multiple nodes, the routing cannot be spread to all of the side, which of the following are several waysto solve this problem ().

A. Use multiple physical interfaces to connect multiple adjacent nodesB. Use a physical interface of the multiple logical sub-interfacesC. Close the split horizon function, and consider the risk of routing loopsD. Any situation will not produce routing loops, routing loops do not need to consider the risk



QUESTION 83On X.25, the following description is correct

A. The structure of the OSI reference model, X.25 protocol defines the physical layer to packet layer from atotal of three content

B. Physical layer defines the DTE and DCE physical connection between the electrical characteristics ofC. link layer defines the interaction between DTE and DCE frame format and procedures, that is balanced Link

Access Procedure LAPB (Link Access Procedure Balanced)D. describes the packet layer packet layer packet formats used, and two three-entity rule between thepacket

switching



QUESTION 84X.25 network is working on the phone line, telephone line reliability of this media is not good, X.25 through whatmechanisms to ensure data transmission

A. Error HandlingB. RetransmissionC. link redundancyD. All of the above



QUESTION 85If the device access X.25 public packet networks, access to the X.25 interfaces must be in accordance with theaccess requirements of service providers to set up an address, this address is called

A. IP addressB. MAC addressC. VPI / VCI identifierD. X. 121 Addresses



QUESTION 86In the X.25 protocol, a virtual interface can connect up to establish how many

A. 1024B. 2048C. 4095D. 4096



QUESTION 87X.25 LAPB protocol sub-layer is divided according to the OSI seven layer protocol are:




QUESTION 88Set interface link layer protocol is X.25, and specify the work order is for the DTE

A. [RouterA-Serial1/0/0] link-protocol x25 dceB. [RouterA-Serial1/0/0] link-protocol x.25 dceC. [RouterA-Serial1/0/0] link-protocol x25 dteD. [RouterA-Serial1/0/0] link-protocol x.25 dte



QUESTION 89Judge: X.25 network is a connection-oriented packet-switched network.

A. TrueB. False



QUESTION 90X.25 physical layer ().

A. LAPDB. X. 21C. H. 264D. SDH



QUESTION 91LAPB frame numbering Which of the following types of encoding are

A. Mode 8B. Mode 64C. Model 128D. Mode 256



QUESTION 92In the following protocol, technology, connection-oriented approach to communication has

A. ATMB. IP

C. CLNPD. X.25



QUESTION 93X.25 link layer protocol Link Access Procedure Balanced (LAPB) defines the interaction between DTE and DCEframe formats and protocols, link layer's main function is

A. In the DTE and DCE to transfer data efficiently betweenB. Make sure the receiver and transmitter synchronization of information betweenC. detecting and correcting transmission errors resultingD. Identification procedures to report high-level protocol errorsE. notify the link layer to packet layer state



QUESTION 94In the X.25 network, Quidway Router can serve as the following which type to use?

A. DTE equipmentB. DCE equipmentC. X.25 packet switching equipmentD. PSN equipment



QUESTION 95Judge: X.25 virtual connection through the exchange of data with the right side.

A. TrueB. False



QUESTION 96

To configure X.25 on an interface you need to do the following

A. The interface packageB. Set X.25 modeC. Set the X.121 address of the interfaceD. Configure X.25 map



QUESTION 97X.25 configuration of a router interface in the mapping statement is as follows:[RouterA-Serial1/0/0] x25 map ip 168.173.24.2 x121-address 30561002What is the argument 30,561,002

A. The end of the X.121 address of the interfaceB. the X.121 address of the peer interfaceC. The flow parameters of the end of the interfaceD. The end of the flow parameters of the interface



QUESTION 98Judge: X.25 data frame contains the source and destination addresses.

A. TrueB. False



QUESTION 99Defined by ITU-T, ATM to () as the basic unit of information transmission, multiplexing and switching

A. FrameB. PackageC. SectionD. Cell



QUESTION 100ATM is connection-oriented exchange, each virtual circuit to use () to identify

A. DLCIB. X.121 addressC. VPI / VCID. IP address



QUESTION 101ATM features include

A. Connection-orientedB. fast packet switchingC. Statistical MultiplexingD. Support for multi-rate, multi-serviceE. supports voice, data and imageF. provide complete real-time QoS guarantee business

Correct Answer: ABCDEFSection: (none)Explanation


QUESTION 102Judge: ATM is connection-oriented packet-switched network, the main body in a single network to carry avariety of information media, carrying a variety of communication services, and to ensure QoS.

A. TrueB. False



QUESTION 103The following cell on the ATM UNI and NNI cell argument, which is correct ().

A. contains the VPI field, but different lengthsB. contains the VCI field, but different lengths

C. Only UNI cell field containing GFCD. UNI and NNI cell cell of the same length, are 53 bytes



QUESTION 104ATM defines different types of business adaptation protocol, commonly used voice that adaptation protocol ().

A. AAL 1B. AAL 2C. AAL 3 / 4D. AAL 5



QUESTION 105The following description which refers to the ATM business (). Depends mainly on the peak cell rate (PCR), theaverage cell rate (SCR), maximum burst size (MBS) and cell delay tolerance (CDVT) to describe. Source sendsthe cell rate is variable, meaning that the source can be considered

A. CBRB. rt-VBRC. nrt-VBRD. UBR



QUESTION 106ATM cell has 53 bytes of fixed length, which occupies the cell header () bytes

A. 4B. 5C. 6D. 10



QUESTION 107ATM protocol framework is divided into three basic planes, respectively,

A. User PlaneB. Control PlaneC. Management PlaneD. fit plane



QUESTION 108IPoA (IP over ATM) protocol using which package ().

A. RFC 1483 RB. RFC 1483 BC. A, B can beD. A, B is not on the



QUESTION 109Using ATM switching technology, with the same header of the cell in the transmission line does not correspondto a fixed time gap, not by cycle occurs. Therefore, the channel reuse by ().

A. synchronous time division multiplexingB. PCM multiplexC. Frequency Division MultiplexingD. Asynchronous Time Division Multiplexing



QUESTION 110ATM header format in the virtual channel identifier field VPI and VCI virtual channel identifier field function is ().

A. used to identify data typesB. used to determine the order of priority to sendC. Path Selection forD. for congestion control



QUESTION 111ATM cell structure, there are two, namely

A. UNI cellB. NUI cellC. NNI cellD. INI cell



QUESTION 112Judge: VC switching refers to the exchange process only change the VCI value, pass-through VPI value. TheVP exchange process VPI, VCI has changed.

A. TrueB. False



QUESTION 113Judgments: When two routers directly connected through the ATM interface or through the WDM (WavelengthDivision Multiplexing) connections should be configured to use one end of the main clock mode, the other endfrom the clock mode. When and SDH / SONET equipment are connected, the router should be configured fromthe clock.

A. TrueB. False



QUESTION 114IGP is scoped

A. area

B. LANC. Autonomous SystemD. Natural subnet range



QUESTION 115The following statement on the routing priority, the right is

A. Only for between RIP and OSPFB. between different routing protocols forC. is an important basis for routingD. direct route default priority is 0



QUESTION 116In the IGP protocol, to a destination a number of different paths that have the same path cost, these routes inthe routing table is called

A. equivalent routeB. sub-optimal routingC. Multi-path routingD. default route



QUESTION 117The common link-state routing protocol

A. RIPB. BGPC. IS-ISD. OSPF



QUESTION 118By the routing algorithm to calculate the points, routing protocols are divided into

A. IGPB. EGPC. Distance VectorD. Link state



QUESTION 119IP routing table, which usually contains the following information:

A. Destination network addressB. costC. Outgoing interfaceD. Next hop address



QUESTION 120Common IGP routing protocols, including

A. RIPB. OSPFC. IS-ISD. BGP



QUESTION 121Judge: each router is only responsible for their own site data packets through the optimal path forward, throughmany routers a relay station to station to forward the packet to the destination.

A. TrueB. False

Correct Answer: A



QUESTION 122The main function of the router, the following statements is correct ().

A. Check the destination of the packetB. Identification of sources of informationC. may be found in the routingD. Validation and maintenance of routing information



QUESTION 123A route in the routing table proto field is direct, indicating that the route is ().

A. Link Layer protocol that routesB. Interface RoutingC. direct routesD. default route



QUESTION 124Which of the following correctly describe the routing protocol?

A. allow the transmission of data packets in a protocol between the hostB. define the packet format and use of the domain as a wayC. By executing a routing algorithm to complete a protocolD. Specify the MAC address and IP address and time bound manner, a protocol




QUESTION 125Link-layer protocol that route, the following statements is correct ().

A. No maintenanceB. can only find a route to the loopback addressC. where the interface can only be found in the directly connected segment of the routeD. can only be found in the inter-network routing



QUESTION 126The following description of the function on the router is properly

A. bring together different types of network interconnectionB. sub-packet to the packet forwarding inC. will forward packets from one network to another networkD. Addressing



QUESTION 127Description of the routing table is correct

A. next hop routing table is redundant, there is the interface can guide the packet forwardingB. route different sources, its priority is not the sameC. the cost between different routing protocols have comparable valuesD. the cost between different routing protocols do not have comparable values



QUESTION 128

In the Quidway routers, you should use the command () to observe the routing table

A. display ip pathB. display ip routing-tableC. display interfaceD. display current-configuration



QUESTION 129Routing table which source routing

A. Physical layer protocol discoveryB. Link layer discovery protocolC. added the administrator manuallyD. Dynamic routing protocols found



QUESTION 130Following the routing table which is not included in the

A. source addressB. next hopC. Target NetworkD. routing metric



QUESTION 131In the router, if multiple routes to same destination, then the factors that determine the best route

A. routing priorityB. Routing publisherC. The cost value of routeD. route lifetime



QUESTION 132The following protocol is the routing protocol is

A. RIPB. IS-ISC. OSPFD. PPPE. IPXF. BGP

Correct Answer: ABCFSection: (none)Explanation


QUESTION 133The following statement which is correct

A. routing priority routing metric is calculated with the sameB. routing path metric calculation may be based on the calculation of a single property, multiple properties may

also be based on pathC. If several dynamic routing protocols are found to the same destination network, the best route, which will be

joined by a couple of choices in the routing tableD. Dynamic routing protocols in accordance with the routing metric to determine the quality of routing and

routing protocols to determine each method is not the same



QUESTION 134The following routing protocols, multicast routing protocol which is

A. RIPB. PIM-DMC. PIM-SMD. DVMRP



QUESTION 135

Judgement: When the network fails, you can automatically correct the static routes, does not require theadministrator to reconfigure.

A. TrueB. False



QUESTION 136According to discover routes and route calculation method to distinguish between distance vector protocolconcerns ().

A. the number of hops to the destination addressB. The next hop address specified by handC. whether the aggregation routing outgoing interface portD. link bandwidth resource information



QUESTION 137When the routing table entry address how the same routing information, the router selection () as a match.

A. Multicast AggregationB. shortest pathC. longest maskD. minimum number of hops



QUESTION 138The problem can cause routing loops

A. slow convergenceB. packet forwarding in the router to cycleC. router restartD. routing inconsistencies



QUESTION 139The following statement is incorrect

A. Each static route is not the same priority can also beB. default route priority order of OSPF> RIPC. The larger routing cost, the better the routeD. VRP, the routing protocol priority values indicate a higher priority higher



QUESTION 140Route from the ring may be the cause

A. routing convergence process of the temporary loopB. routing algorithm defectsC. In a different routing domain into another routing loop to prevent loss of informationD. Configure error



QUESTION 141To deploy a large network, select the routing protocol, there needs to be considered

A. routing protocol scalability for network supportB. routing protocol maturity, the degree of support to manufacturersC. protocol packet overheadD. convergence speed and routing loop will produce



QUESTION 142Identifies the cost of routing out the route to reach the destination address within the meaning of the cost, toselect the best path, which of the following factors will generally affect the cost value of route

A. line delay, bandwidthB. Line share

C. Line credibilityD. hops



QUESTION 143To support variable length subnet mask, routing protocols are:

A. RIP v1B. RIP v2C. OSPFD. IS-IS



QUESTION 144Measuring the performance of dynamic routing protocols indicators

A. correctnessB. faster convergenceC. Low overheadD. SafetyE. universal



QUESTION 145A router routing table is as follows:Routing Tables:Destination / Mask Proto Pre Cost NextHop Interface- 2.0.0.0 / 8 Direct 0 0 2.2.2.1 Serial0- 2.2.2.1/32 Direct 0 0 2.2.2.1 Serial0- 2.2.2.2/32 Direct 0 0 127.0.0.1 LoopBack0- 3.0.0.0 / 8 Direct 0 0 3.3.3.1 Ethernet0- 3.3.3.1/32 Direct 0 0 127.0.0.1 LoopBack0- 10.0.0.0 / 8 Static 60 0 2.2.2.1 Serial0- 127.0.0.0 / 8 Static 0 0 127.0.0.1 LoopBack0- 127.0.0.1/32 Direct 0 0 127.0.0.1 LoopBack0At this time when the router from the Ethernet port sent to the 11.1.1.1 host receives a packet, the router how todeal with

A. lostB. forward from Serial0C. forward from Ethernet0D. forwarding from LoopBack0



QUESTION 146A router routing table is as follows:Routing Tables:Destination / Mask Proto Pre Cost NextHop Interface- 2.0.0.0 / 8 Direct 0 0 2.2.2.1 Serial0- 2.2.2.1/32 Direct 0 0 2.2.2.1 Serial0- 2.2.2.2/32 Direct 0 0 127.0.0.1 LoopBack0- 3.0.0.0 / 8 Direct 0 0 3.3.3.1 Ethernet0- 3.3.3.1/32 Direct 0 0 127.0.0.1 LoopBack0- 10.0.0.0 / 8 Static 60 0 2.2.2.1 Serial0- 127.0.0.0 / 8 Static 0 0 127.0.0.1 LoopBack0- 127.0.0.1/32 Direct 0 0 127.0.0.1 LoopBack0At this time when the router from the Ethernet port sent to the 10.1.1.1 host receives a packet, the router how todeal with

A. From forwarding to 2.2.2.1 Serial0B. forwarded to 2.2.2.1 from Ethernet0C. forwarded to the target host from Serial0D. forwarded to the target host from Ethernet0



QUESTION 147Known to a router's routing table entry has the following two Destination / Mast Protocol Pre Cost Nexthop Interface- 9.0.0.0 / 8 OSPF 10 50 1.1.1.1 Serial0- 9.1.0.0/16 RIP 100 5 2.2.2.2 Ethernet0If the destination address of the router to forward packets to 9.1.4.5, the following statements is correct is

A. Select the first match, because the high priority OSPF protocolB. Choose the second match, because the cost of the value of the RIP protocol smallC. Select the second match, because exports are Ethternet0, faster than the Serial0D. Select the second match, because the routing entry for the destination address 9.1.4.5, it is more accurate

match



QUESTION 148Quidway routers a two Ethernet ports E0 and E1 are connected to two network segments: E0 (IP address10.1.1.1, subnet mask 255.255.255.0) is connected to the network A, E1 (IP address 10.1.2.1, subnet mask255.255.255.0) is connected to the network B. Assuming the host of the network gateway are set correctly,following which hosts can Ping through network A to host

A. A, in the network of a host, its IP address 10.1.1.12, subnet mask 255.255.0.0B. A in the network of a host, its IP address 10.1.2.16, subnet mask 255.255.0.0C. B, in the network of a host, its IP address 10.1.2.14, subnet mask is 255.255.255.0D. A, in the network of a host, its IP address 10.1.1.8, subnet mask is 255.255.255.0



QUESTION 149Quidway routers, enter the "display ip routing-table" command to display information as follows:[Quidway] display ip routing-tableRouting Tables:Destination / Mask Proto Pre Cost Nexthop Interface- 10.1.1.0/24 RIP 100 1 10.1.3.1 Serial1- 10.1.2.0/24 Direct 0 0 10.1.2.1 Serial0- 10.1.3.1/32 Direct 0 0 10.1.3.1 Serial1- 10.1.3.2/32 Direct 0 0 127.0.0.1 LoopBack0- 127.0.0.0 / 8 Direct 0 0 127.0.0.1 LoopBack0- 127.0.0.1/32 Direct 0 0 127.0.0.1 LoopBack0- 192.168.1.0/24 RIP 100 1 10.1.3.1 Serial1- 192.168.2.0/24 RIP 100 1 10.1.2.1 Serial0The following statement is correct:

A. This command displays the router how to reach the destination networkB. "RIP", said the route information is found by the dynamic routing protocol RIPC. "Direct" indicates that this route information is the router's directly connected segmentD. NextHop field shows in order to reach the destination network, the router should forward the datagram to

the next station Layer 3 network devicesE. The RIP is hop count to calculate the cost to value, so the cost is equal to 1 indicates to the destination

network 192.168.1.0 need to go through a router



QUESTION 150Default route can be derived from the

A. Manual ConfigurationB. The router itself

C. Dynamic routing protocols generatedD. Link Layer protocol produced



QUESTION 151Which of the following routing protocols for IPv6 service

A. RIPv 6B. RIPngC. OSPFv 2D. IS-ISv6



QUESTION 152Huawei routers by default, OSPF and ISIS routing priority routing priority compared to the following statementsis correct ().

A. OSPF routing betterB. OSPF route preference value smallerC. the same as the two priorityD. ISIS routing priority values smaller



QUESTION 153Is the equivalent route to the same destination a few () of the route.

A. the same costB. the same priorityC. The same outgoing interfaceD. the same next hop



QUESTION 154In the network, routers use () to guide the packet forwarding.

A. DNS lookupB. ARP tableC. Routing tableD. MAC address table



QUESTION 155On the routing convergence, the following statements is most accurate

A. Network convergence is due to changes caused by the change processB. Convergence refers to the routers send hello packets among neighbors in the process to formC. Convergence of two routers to their routing tables into a single processD. Convergence of the network routing tables of all the synchronization process, or simply can be defined as a

router on the network changes to take appropriate measures to achieve steady-state process



QUESTION 156When the router receives the packet destination IP address in the routing table does not match the table entry,the strategy adopted

A. lost packet.B. Place the packet fragmentationC. Forwards the packet.D. If the default route exists in accordance with the default route forwarding, or discarded



QUESTION 157Judgement: When the network topology changes, if the best path to reach the destination IP is not available,the dynamic routing protocol can adapt to network changes, determine the other's best path to reach thedestination IP.

A. TrueB. False



QUESTION 158Developed by the IETF, the principle itself is more complex protocol, using a wide range of interdomain routingprotocol ().

A. BGPB. OSPFC. ISISD. RIP



QUESTION 159Protocol configuration is simple, slow convergence, commonly used in small and medium refers to the networkrouting protocols ().




QUESTION 160for the AS exchange routing information between routing protocol means ().




QUESTION 161

Judge: Each autonomous system has a unique autonomous system number, in an autonomous system, youcan use a variety of routing strategies.

A. TrueB. False



QUESTION 162The correct statement about the system is autonomous

A. Autonomous System routing protocol is running the same regionB. autonomy within the system can run one or more IGPC. Autonomous System is a set of regulatory bodies in the same set of routers under the control ofD. BGP autonomous systems such as the use of external gateway routing protocols exchange routing

information



QUESTION 163When the router receives the data link layer upper than the length of the text of the transmitter to send thepacket to the router interface to the largest MTU, the strategy adopted

A. lost packet.B. Place the packet fragmentationC. request to the source router, reducing the size of its packetsD. forwards the packet directly



QUESTION 164in the different exchange routing information between autonomous systems, routing policy and route filteringcontrols inter-domain routing information in the self-propagation, this routing protocol is ().

A. IGPB. BGPC. EGPD. IBGP

Correct Answer: C



QUESTION 165Based on Bellman - Ford algorithm, usually in a certain time interval to the adjacent router sends a completerouting table. Configuration is simple, poor scalability, which refers to the routing protocol().

A. Distance Vector routing protocolB. Link State Routing ProtocolC. Interior Gateway ProtocolD. exterior gateway protocol



QUESTION 166Using the incremental update mechanism, only when the link state changes when sending routing updates.Belong to the routing protocol with ().




QUESTION 167The following statement in the loop on the route, the right is

A. routing loops so that messages cannot be correct to the destination, and cause the link congestionB. routing loop can only be generated through the dynamic routing protocolC. two or more packets in routing loops between routers until the TTL to 0 and discardD. link-state protocol does not produce routing loop



QUESTION 168in the different routing protocols exchange routing information between the process called ().

A. routing introductionB. Route AggregationC. routing loopsD. Default routes



QUESTION 169The following () indicators used to measure the performance of dynamic routing protocols.

A. No routing loopsB. protocol overhead of their ownC. The number of sub-segment is dividedD. Routing priority



QUESTION 170Static routing configuration commands specify the parameters reject ().

A. unreachable routesB. Black Hole RoutingC. routing loopsD. Iterative routing



QUESTION 171Static routing blackhole configuration commands specify the parameters ().

A. unreachable routesB. Black Hole RoutingC. routing loopsD. Iterative routing



QUESTION 172Hit unreachable route, it will do the following ().

A. go to the destination of any IP packet will be discardedB. send ICMP messages to notify the source host unreachable destination IPC. Do not send ICMP unreachable messages to the source hostD. send TTL-1 packet notifying the source host



QUESTION 173The following description for the default route is correct:

A. The default route is the preferred route to be usedB. default route is the route used lastC. You can manually configure the default routeD. The default route is a special kind of dynamic routing



QUESTION 174If an internal network is only one exit outside, then the best configuration

A. The default routeB. Host RoutingC. Dynamic RoutingD. direct routes



QUESTION 175In a computer running Windows to configure the gateway, similar to the configuration in the router

A. direct routesB. default routeC. Dynamic RoutingD. Host Routing



QUESTION 176In the VRP platform, the default static route is a priority

A. 0B. 20C. 60D. 100



QUESTION 177Judge: by the administrator to manually configure a static route is made can also be automatically generated.

A. TrueB. False



QUESTION 178Huawei routers static routing configuration command ().

A. ip route-staticB. ip route staticC. route-static ipD. route static ip



QUESTION 179Static routing configuration command parameters in the destination IP address and mask, the mask that cantake the form ().

A. dotted-decimalB. mask length (in the mask? Norwegian Chennai Wong?

C. dotted binaryD. dotted hexadecimal



QUESTION 180Static routing configuration command preference_value parameters, the following statements is correct ().

A. In the same command several times in preference_value value input, multiple effectB. In the same command several times in preference_value value can be entered, only the first validC. In the same command several times in preference_value value can enter, only the last validD. to reach the same destination IP address for multiple routes, routing can be configured to achieve different

preference_value backup



QUESTION 181The following static route is configured correctly

A. ip route-static 129.1.0.0 16 serial 0B. ip route-static 10.0.0.2 16 129.1.0.0C. ip route-static 129.1.0.0 16 10.0.0.2D. ip route-static 129.1.0.0.255.255.0.0 10.0.0.2



QUESTION 182On the alternate route is to say the right ().

A. not added to the global routing tableB. does not guide the data forwardingC. After the primary route fails, the main route will rise, adding to the global routing tableD. simultaneously with the main route guidance data transmitted



QUESTION 183Static route configuration key difference between reject and blackhole

A. sent to reject the routing of packets to be discarded, and not the source hostB. sent to blackhole routing of packets to be discarded, and not the source hostC. sent to reject the routing of packets to be discarded, sent to blackhole routing packets are not discardedD. sent to blackhole routing of packets to be discarded, sent to reject the routing of the packets are not

discardedE. sent to reject the routing of packets to be discarded, and the source hostF. sent to blackhole routing of packets to be discarded, and the source host

Correct Answer: BESection: (none)Explanation


QUESTION 184With static routing protocols, the advantages of dynamic routing

A. less bandwidthB. simpleC. router can automatically discover the network topology changesD. router can automatically calculate a new route



QUESTION 185Static routes include:

A. Configure the simpleB. automatically update routesC. Improving network securityD. save bandwidth



QUESTION 186Static route on the right have priority claims

A. In the network configuration to reach the same destination multiple routes, if assigned the same priority,load sharing can be achieved

B. VRP in the default static route preference value of 10

C. configure the network to reach multiple routes to the destination, if specified different priorities, you canachieve the routing backup

D. VRP in zero static routing overhead



QUESTION 187Two static routes configured on the routers to reach network 10.1.1.1/32, which is not a static route setpreference_value, the other a static route preference_value configured for 100, the following statements iscorrect ().

A. The route is not set as the main route preference_valueB. preference_value configured to route 100 as the main routeC. Static route support for routing backupD. two routes to achieve load sharing



QUESTION 188Two static routes configured on the routers to reach network 10.1.1.1/32, which is not a static route setpreference_value, the other a static route preference_value configured for 100, display ip routing-table can beseen ().

A. There is only one route to reach 10.1.1.1/32B. There are two routes to reach 10.1.1.1/32C. do not see preference_value routing table route 100D. There preference_value route 60



QUESTION 189in the router to view the static routes, alternate backup route attribute is expressed as ().

A. BypassB. InactiveC. BackupD. Slave


Explanation


QUESTION 190The following statements is correct about the default route is:

A. The default route is a special route, you can configure a static routeB. Some dynamic routing protocols can also generate a default route, such as OSPF and IS-ISC. The default route is no matching entry in the routing table when using the route. That is, only when no

suitable route, default route was used Default route in the routing tableD. The purpose of the network and mask of 0.0.0.0 and 0.0.0.0



QUESTION 191The following statement is true about the default route is ().

A. The default route, also known asB. can only be manually configured by the administratorC. is a special kind of static routeD. Dynamic routing protocols can also generate a default route



QUESTION 192When the router receives a routing table lookup in the destination than the packet will match ().

A. OSPF routingB. RIP RoutingC. BGP routingD. default route



QUESTION 193Default form of the route is ().

A. destination IP is all zeros, the mask is all 1

B. destination IP for the whole 1, mask of all 0C. destination IP and mask are all 0D. destination IP and mask are all 1



QUESTION 194Huawei router's default route on the maximum support (), route load balancing.

A. 0B. 2C. 16D. 32



QUESTION 195Changes in network topology, the () will not automatically change, must have a network administratorintervention.

A. ISIS routingB. OSPF routingC. BGP routingD. Static routes



QUESTION 196he following is a distance vector routing protocol




QUESTION 197RIP routing table update packets sent cycle is () s

A. 5B. 30C. 60D. 180



QUESTION 198RIP (Routing Information Protocol) protocol to use () for interactive routing information, each certain timeinterval to send out an update message.

A. TCPB. UDPC. RSVPD. LDP



QUESTION 199Judge: RIP (Routing Information Protocol) protocol version RIPv1, RIPv2 and RIPv3.

A. TrueB. False



QUESTION 200A RIP route becomes unreachable, the router through () did not receive the RIP routing information updatepacket, the RIP route is removed from the routing table.

A. 120sB. 180sC. 240sD. 300s



QUESTION 201In the RIP, the router directly connected to the network with its hop count ().

A. 0B. 1C. InfinityD. None of the above



QUESTION 202RIPv2 default use () method to send messages.

A. UnicastB. MulticastC. BroadcastD. Multicast and broadcast



QUESTION 203RIPv2 Which version supports the following features ().

A. Variable-length subnet maskB. Route AggregationC. clear text authenticationD. MD 5 ciphertext authentication




Huawei HCDA Fast Track training (SU0-211)

Documents