High Performance Unvented Attics with Fiberglass Insulation · 4/4/2014 · High Performance Unvented Attics with ... (IRC 2012 table R806.5) Climate Zone Minimum rigid board or ...

High Performance Unvented Attics with Fiberglass Insulation

Building Science Group, Sustainability Owens Corning

Acknowledgments

• Dr. William Miller – Oak Ridge National Laboratory

• Dr. Andre Desjarlais – Oak Ridge National Laboratory

• Mikael Salonvaara – Owens Corning

• Abe Cubano –Owens Corning

• Neil Freidberg – Owens Corning

Field Testing # 1

Field Testing # 2

Advanced Modeling

Mixed Climate

Hot-Cold-Humid

Hot-Dry Both Climates

2

Outline

• Moisture in above and below roof deck insulation

• Impact of vented and non-vented attics on moisture in attics

• Performance Results

• Discussion and Conclusions

3

Attic Types and Moisture Management

Sealed (Unvented) Attic Vented Attic

Ducts inside thermal boundary Ducts in unconditioned space

Attic is not living space and not intentionally conditioned

Attic is ventilated with outdoor air

4

Approach

• Focus on moisture performance

– Condensation, wetting and drying of roof deck

• Tools

– Simulations with hygrothermal models

– Field testing • Air tightness and temperature/humidity measurements

5

Typical Insulation in Unvented Attics

• Spray foam: Chemicals mixed, applied and cured on-site

– Open Cell • Low density (~0.5 pcf), Vapor permeable

– Closed Cell • High density (~2 pcf), Low vapor permeability

• Air permeable insulation

– Dense packed fibrous insulation

– Condensation control layer e.g. exterior foam may be needed

www.Insulatewithintegrity.com

6

Unvented Attics in Building Codes

International Residential Code (IRC) R806.5

• “Unvented attic and unvented enclosed rafter assemblies” – Requires air impermeable

insulation in direct contact with the roof sheathing

– If air permeable insulation is used

• The air permeable insulation has to be supplemented with a condensation control layer (air impermeable insulation) either on top of or under the roof sheathing.

Condensation Control - IRC

Table 3. Minimum R-values of Air-impermeable Insulation in Unvented

Attics. (IRC 2012 table R806.5)

Climate Zone Minimum rigid board or

air-impermeable insulation R-value

2B and 3B tile roof only None required

1, 2A, 2B, 3A, 3B, 3C R-5

4C R-10

4A, 4B R-15

5 R-20

6 R-25

7 R-30

8 R-35

8

MEASURED AND SIMULATED TEMPERATURE & RELATIVE HUMIDITY

ORNL Test House – Model Calibration

Model Calibration

• Field Testing

– ORNL test house with Sealed Attic

• Structure

– Shingles

– Underlayment

– OSB

– 1” Closed Cell **

– ~5” Open Cell

– Spray-on fiber glass insulation 2”

10

Measured and Simulated Temperature

Temporary plastic

on top of roof

11

Measured and Simulated Relative Humidity

12

ROOF DECK MOISTURE – MODELING OF DEMO HOUSE

Climate zones 3B

Roof Assembly

• The layers in the roof listed – from exterior to interior – are:

– Roof tile

– 1” Air gap

– Roofing underlayment

– ½” Roof sheathing (OSB) and

– Fiberglass insulation.

14

WUFI Model

ASHRAE 160

OSB moisture content in Unvented and Vented attics

Climate zones 3B

15

More forgiveness in

Ventilated Attics

Fiberglass solution

Works well for

Unvented Attics

San Marcos, CA

Roof Deck Performance Results

• Unvented Attic

• Climate Zone and City

• Indoor moisture loads +4 g/m3

• Focus on Roof Deck Moisture (OSB)

1 Miami, FL

2 Houston, TX

3 Atlanta, GA

4 Baltimore, MD

16

Unvented Attic – Roof Deck Moisture

No water intrusion With water intrusion (1%)

Open Cell A2 (54 perm-in)

17

Unvented Attic – Roof Deck Moisture

No water intrusion With water intrusion (1%)

Open Cell A1 + Intumescent Coating (1-3 perms)

Note: Closed Cell foam is even more vapor tight than the above

18

Unvented Attic – Roof Deck Moisture

No water intrusion With water intrusion (1%)

Fiberglass Insulation (100 perm-in) + Air sealing

19

Unvented Attic – Roof Deck Moisture

No water intrusion With water intrusion (1%)

Fiberglass Insulation (100 perm-in) +

Air sealing +10 perm VR

20

Climate Makes a Difference

• Hot to Cold, Wet to Dry climates (CZs 1-3)

Asphalt

FG

21

Climate vs Moisture Load

San Francisco

CZ3C, sensitive

San Diego, high moisture

load causes no problems

Asphalt shingles

22

FIELD HOME – SAN MARCOS CALIFORNIA

KB Homes

Sealed Attic

24

Instrumentation Plan

•Roof surface temperatures

•Roof sheathing temperatures, humidity

and moisture content

• Attic air temperatures north and south

side of attic

•I ndoor air temperature at thermostat

•Weather conditions

•Whole-house energy use

•HVAC run time.

Campbell Scientific Model CR23X

and or CR10X micro-loggers

Building Electrical Monitoring Points Wattnode transducer Model WNA-1P-240-P Whole House Power

ACL1 Event counter OPTI-Line Monitor with DC power

supplied by data logger HVAC On Time 25

Computer Simulations

• Validation of AtticSim: Measured vs Simulated Attic T

AtticSim (version 12.6) 26

Energy Performance

• Ceiling heat flux

27

Air Pressure across attic floor varies ±1 Pa

Data collected August 26, 2013

Wind affects attic-to-indoor pressure gradient

Minimal air leakage at soffits 28

Attic and Indoor T and RH

29

Moisture Loads

Indoor=Air Return

Attic air has about the same moisture content as indoor air Attic/Indoor is drier than outdoors most of the year

30

T/RH Under Roof Deck

North South

31

T/RH Under Roof Deck

West East

32

T/RH Over Roof Deck

33

Roof Deck Air Leakage

• Air leakage between attic and outdoors must be understood

– Is the attic ‘sealed’?

• Dual blower door testing is needed to separate component leakage

34

Air Tightness of the Attic

• Testing to separate Attic-to-Outdoors and Attic-to-Indoors air leakage characteristics

• Methods

– Dual Blower Door: = Blower door flow

– Multi-scenario tests at multiple pressure levels

-50Pa -50Pa

-50Pa

? Pa

-50Pa 0Pa

0Pa

35

Attic-to-Outdoors Air Leakage

• Fiberglass attics

– First house (San Marcos) cfm50=515

– Second house (Lancaster) cfm50=369

• SPF attic

– Knoxville, TN: cfm50=336

• First house was ‘test and learn’

• Second house shows fiberglass attic can be air sealed as well as a sprayfoam attic

36

Draped vs Boxed Netting

Thermal Performance with the same average thickness of 7.5”

37

Thermal Performance

• Draped Netting

• U-value = 0.044

• Truss cords exposed to attic – thermal bridge and cold spot (condensation)

• Boxed Netting

• U-value = 0.033 25% better

• Permits future vapor permeance tuned netting for controlling truss cord moisture 38

Box Netting- evolved Wolf/Walden/Salonvaara

Unvented Attic # 2 39

40

Summary:

1. Unvented Attic design # 1 (Drapped systems) has demonstrated

outstanding performance for a full year of monitoring.

2. Fiberglass is a cost effective solution with excellent performance.

3. No risk was found for the hygrothermal performance of the unvented

attic

4. Fiberglass is non-flammable, non VOC and mold resistant

5. Box netting results in superior thermal & moisture performance

Conclusions

40