GARDNER SCREW CORPORATION Screw Machine Products • Furniture Hardware • Metal Fasteners & Stamping • Industrial Supplies Serving Industry Since 1923 Hi-Torque Wood Screws – Phillips 220 Union Street, Gardner, MA 01440-0862 • Telephone (978) 632-0850 • Fax (978) 632-4606 • Email: [email protected]www.gardnerscrew.com 01F-09/07 Improved gimlet points facilitate easy driving. Precision helix angle and thread form. Phillips #3 Recess on #10 Screws Every inch of thread is always “working”— load does not fall on any one section of thread. 1/8” full shank increases torsional strength. Sharp uniform threads cut deeply and cleanly into material with reduced effort. Heat-treated to precise specification and maximum strength. • Increased number of threads allows use of shorter length screws reflecting cost reduction. • Forging process provides a tougher screw. • Easier driving means better efficiency — wood fibres are not crushed.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
As every good cabinet worker knows, there isconsiderable variation in condition and grade ofwood. Therefore, any pilot hole recommendationis for average conditions, allowance may have tobe made by a competent craftsman to meetspecific conditions.
Too large a hole provides insufficient gripping surface.An undersize pilot hole likewise weakens the fastening,because the fibre of the wood is crushed and granulationsare packed in the thread root. This sets up stresses whichtend to split or crack the wood.
The following table lists recommended hole diameters,from which the experienced woodworker will varyaccording to his needs.
220 Union Street, Gardner, MA 01440-0862 • Telephone (978) 632-0850 • Fax (978) 632-4606 • Email: [email protected]
www.gardnerscrew.com04-09/07
Flat Recex® Deep Thread Screwswith Nibs and Type-17 Point
• Patented Recex® Square-Phillips Combination Recess Zip Driverfor drive versatility, insures you always have the correct driver bitto install or adjust your finished wood working project.
• Dependable Type-17 point pre-drills the wood while the nibsunderneath the head allow the fastener to self-countersink itselfinto all types of soft and hardwoods (particleboard and softwoods).
Finish Case WeightSize Part No. Black Zinc Qty. lbs.
8 x 1 MFRP08100SN -F -Z 1M 3.64
8 x 1-1/4 MFRP08114SN -F -Z 1M 4.44
8 x 1-1/2 MFRP08112SN -F -Z 1M 5.29
8 x 1-5/8 MFRP08158SN -F -Z 1M 5.82
8 x 1-3/4 MFRP08134SN -F -Z 1M 6.04
8 x 2 MFRP08200SN -F -Z 1M 7
8 x 2-1/4 MFRP08214SN -F -Z 1M 7.71
8 x 2-1/2 MFRP08212SN -F -Z 1M 9.2
8 x 2-3/4 MFRP08234SN -F -Z 1M 10.46
8 x 3 MFRP08300SN -F -Z 1M 11.5
Finish Case WeightSize Part No. Black Zinc Qty. lbs.
220 Union Street, Gardner, MA 01440-0862 • Telephone (978) 632-0850 • Fax (978) 632-4606 • Email: [email protected]
www.gardnerscrew.com06-09/07
Extra large washer built into the head for increased bearing surface and maximum holecoverage. The unique head design is a timesaver for the professional cabinet maker.
Case WeightSize Part No. Finish Qty. lbs.
CWXP08078R2Z 100 0.54
8 x 7/8 MWXP08078R2Z Full Thread 1M 5.4
BWXP08078R2Z 10M 54
8 x 1 BWXP08100R2F Black 7M 46Half Thread
CWXP08100R2Z 100 0.6
8 x 1 MWXP08100R2Z Half Thread 1M 6
BWXP08100R2Z 10M 44
CWXP08118R2Z 100 0.64
8 x 1-1/8 MWXP08118R2Z Zinc 1M 6.43
BWXP08118R2Z Half Thread 6.5M 44
CWXP08114R2Z 100 0.7
8 x 1-1/4 MWXP08114R2Z Zinc 1M 7.03
BWXP08114R2Z Half Thread 6.5M 46
8 x 1-1/2 MWXP08112R2Z Zinc 1M 8
BWXP08112R2Z Half Thread 5M 40
Modified Truss – Phillips Deep ThreadExtra Large Washer Head Screw
1/2" head diameter
Step 1 - Drill oversized 5/16" holes in drawer box.Step 2 - Attach drawer front by driving screws
through box and into drawer front.Step 3 - Adjust drawer front.
(the oversized holes ensure perfect alignment)Step 4 - Fix drawer front with knob or pull screws
Case WeightSize Part No. Finish Qty. lbs.
8 x 1 MWRP08100S2Z Zinc 1M 6
BWRP08100S2Z Half Thread 7M 43
8 x 1-1/8 MWRP08118S2Z Zinc 1M 6.43
BWRP08118S2Z Half Thread 6.5M 42
8 x 1-1/4 MWRP08114S2Z Zinc 1M 7.03
BWRP08114S2Z Half Thread 6.5M 47
Modified Truss – Recex® Deep ThreadType 17 Extra Large Washer Head Screw
220 Union Street, Gardner, MA 01440-0862 • Telephone (978) 632-0850 • Fax (978) 632-4606 • Email: [email protected]
www.gardnerscrew.com07F-09/07
The "original" pan head with a higher head height toinsure proper bit fit. Square recess drive fits square bitswith a deeper recess for better grip, incures "slip-proof"driving - no camouts.
Case WeightSize Part No. Finish Qty. lbs.
6 x 1-1/4 MPSA06114S2F Black T17 1M 4.36
6 x 1-1/4 BPSA06114S2F Black T17 10M 43
6 x 1-1/2 MPSA06112S2F Black T17 1M 4.12
6 x 1-1/2 BPSA06112S2F Black T17 8.5M 35
Pan Head /Square Recess DriveFine Thread /Type 17 Point
The "original" pan head with a higher head height toinsure proper bit fit. Fine thread provides easy drivingand maximum strength in hardwoods.
Case WeightSize Part No. Finish Qty. lbs.
6 x 1-1/4 MPXA06114S2F Black T17 1M 4.2
6 x 1-1/4 BPXA06114S2F Black T17 10M 40
6 x 1-1/2 MPXA06112S2F Black T17 1M 4.12
6 x 1-1/2 BPXA06112S2F Black T17 8.5M 35
Pan Head /Phillips Recess DriveFine Thread /Type 17 Point
The "original" pan head with a higher head height toinsure proper bit fit. Square recess drive fits square bitswith a deeper recess for better grip. Deep waxed threadoffers easy driving and maximum hold in softwoods andmanmade materials.
Case WeightSize Part No. Finish Qty. lbs.
7 x 1-1/4 MPSP07114S2F Black 1M 4.22
7 x 1-1/4 BPSP07114S2F Black 9M 39
7 x 1-1/2 MPSP07112S2F Black 1M 5
7 x 1-1/2 BPSP07112S2F Black 6M 30
7 x 1-7/16 BPSP07116S2F Black 6M 30
7 x 1-7/16 BPSP07116S2F Yellow Zinc 6M 30
Pan Head /Square Recess DriveDeep Waxed Thread /Type 17 Point
Serrations under head to lock into frame.Case Weight
Size Part No. Finish Qty. lbs.7 x 1-1/4 MFRH07114S2L Lubricized® 1M 51
7 x 1-1/4 BFRH07114S2L Lubricized® 7.5M 37
7 x 1-1/2 MFRH07112S2L Lubricized® 1M 5.7
7 x 1-1/2 BFRH07112S2L Lubricized® 6M 34
Fillister Head /Recex® DriveHi-Lo™ Thread /Type 17 Point
Larger body for added strength.Case Weight
Size Part No. Finish Qty. lbs.
8 x 1-1/4 BWRP08114F2F Black 7M 38
8 x 1-1/2 BWRP08112F2F Black 5M 31
Round Washer Head /Recex®Drive / Deep Thread /Type 17 Point
• Available in BlackPhosphate, Zinc or ZincYellow Dichromate.
• The most complete line ofcoarse thread drywallscrews. Used in manyapplications, wood to wood,drywall to wood, cabinetinstallation, and outdoorwood decks. Phil. recess.
Trim Head Sharp eziS #traP .ytQ .tW
1x6 001S)P(T M01 sbl03
8/51x6 851S)P(T M5 sbl12
4/12x6 412S)P(T M3 sbl02
3x8 003S)P(T M2 sbl22
• Phillips or square drive.• For attaching wood trim andbase to metal studs.
Wafer Lath SharpeziS #traP .ytQ .tW
61/9x8 Z619W M01 sbl33
4/3x8 Z430W M8 sbl83
1x8 Z001W M5 sbl62
4/11x8 Z411W M5 sbl13
8/51x8 Z851W M4 sbl03
2x8 Z002W M5.2 sbl52
• 9/16 also available in BlackPhosphate.
• For attaching metal lath ork-lath to metal studs20-25 gauge. Zinc finish,Phil. recess.
220 Union Street, Gardner, MA 01440-0862 • Telephone (978) 632-0850 • Fax (978) 632-4606 • Email: [email protected]
www.gardnerscrew.com09B-09/07
Pan Framing Sharp
Laminating Screw
eziS #traP .ytQ .tW
61/7x6 6176SS M51 sbl53
61/7x7 6177SS M51 sbl83
eziS #traP .ytQ .tW
2/11x01 211L M5 sbl83• A temporary fastener forattaching drywall to drywall.Phil. recess.
• Serrations under head toprevent spinning.
• For attaching steel studsto steel track up to 20 gauge.
Trim Head Self-Drill
Cement Board Self-Drill Screws
Pan Framing Self-Drill
eziS #traP .ytQ .tW
61/7x6 6176DS M51 sbl73
61/7x7 6177DS M51 sbl04
61/9x01 61901DS M01 sbl94
• Available in BlackPhosphate or Zincplated. Phil. drive.
• For attaching steel trackto 14-20 gauge metal studs.
Self-Piercing (Slotted) Hex Washer HeadNeedle Point
Wood Screws/Flat Square Head/Coarse Thread
eziS #traP .ytQ .tW
1x6 001DS)P(T M01 sbl03
8/51x6 851DS)P(T M5 sbl22
4/12x6 412DS)P(T M3 sbl91
eziS #traP .ytQ .tW
4/11x8 411RD M5 sbl43
8/51x8 851RD M4 sbl53
4/12x8 412RD M2 sbl22
4/11x8 S411RD M5 sbl43
8/51x8 S851RD M4 sbl53
eziS #traP .ytQ .tW
2/1x8 2108SSH M51 sbl54
4/3x8 4308SSH M01 sbl34
1x8 0018SSH M5.7 sbl73
4/11x8 4118SSH M6 sbl63
2/11x8 2118SSH M5 sbl73
2x8 0028SSH M3 sbl03
2/1x01 21001SSH M41 sbl05
4/3x01 43001SSH M5.7 sbl53
1x01 00101SSH M5 sbl43
2/11x01 21101SSH M3 sbl53
2x01 00201SSH M2 sbl53
eziS #traP .ytQ .tW
1x8 0018SC M01 sbl83
4/11x8 4118SC M8 sbl63
2/11x8 2118SC M6 sbl23
4/31x8 4318SC M4 sbl62
2x8 0028SC M5.3 sbl52
4/12x8 4128SC M3 sbl12
2/12x8 2128SC M5.2 sbl32
3x8 0038SC M2 sbl42
• Phillips or square drive.• Used for attaching woodtrim or base to 14-20gauge metal studs.
• For attaching cementboard to 14-20 gaugemetal studs.
• Special exterior coatingprovides over 500 saltspray hours.
• Extra sharp point forfaster penetration.
• Twin lead thread foreasier installation.
• Used in light metalassembly such aselectrical outlets, framing,and various other sheetmetal applications.
• Slotted head.• Zinc Plated.
• Phillips or square drive.• Black or Zinc finish.• For cabinet installationand other hard wood towood applications.Square drive createsmore positive driving.