READ AND KEEP THIS OPERATION MANUAL • S i m p l e t o i n s t a l l Operation Manual • 1/3" Sony Super HAD CCD • High Resolution:550 TV Lines • 4mm Fixed Lens • Color Day/Night with 24 LEDs • Auto White Balance • AGC, BLC, Flickerless On/Off • Extra Video Output for Installer • 3-Axis Camera Construction • Vandal-Resistant Dome Housing HD70 Series SPECIFICATIONS: DIMENSIONS(mm): COMPOSITION: Model Signal System Scanning System Scanning Frequency (H) Scanning Frequency (V) Image Sensor Total / Effective Pixels No. S / N Ratio Resolution Video Output Level Lens Focus Sync. System Sensitivity Electronic Shutter White Balance AGC BLC Flickerless Input / Output Connector Power Consumption Dome Size (Ø) Weight NTSC PAL NTSC : 525 Lines PAL : 625 Lines 2 : 1 Interlace 15.734kHz 15.625kHz 59.94Hz 50Hz 1/3" SONY Super HAD CCD 410K / 380K 470K / 440K More than 50dB (AGC Off) 550 TV Lines 1.0 Vp-p (75 Ohms, composite) Fixed Lens : f=4.0mm Manual Internal 0 Lux, IR LED 1/60 ~ 100,000 Sec. 1 /50 ~ 100,000 Sec. Auto On / Off On / Off (with Slide Switch) On / Off (with Slide Switch) Power, Video 12VDC (10V~15V) / 5W (Max) 100mm Approx. 844g INSTALLATION: Draw out power / video wires to the connecting places. 3 Stick the guide pattern on the wall or ceiling. 1 Adjust desired focus and scene by turning and moving the 3-axis camera bracket by hand. 5 Drill four holes according to the guide pattern then insert anchors into the drilled holes. 2 Put the dome cover over the base. 6 Fix the dome cover on the base by L-Wrench. 7 Fix the camera to a celling using four screws. 4 You must be fully aware of all the distinctive features and precautions related to this camera before installing it. Built-in camera bracket makes it much easier to rotate in any direction. 3-axis CAMERA SET-UP: Fixed Lens & IR LED Type CAUTION : When AGC is off, D/N does not work because the D/N switching function is dependent on the AGC level. Function Selection Switch: •FL(Flickerless) ON/OFF •AGC(Auto Gain Control) ON/OFF •BLC(Back Light Compensation) ON/OFF Service Monitor Connecter: Use service monitor connector to set camera angle & focus when installing. a b The image does not appear on the screen. Check the power source for the monitor and camera and ensure that the voltage and polarity are properly connected and being supplied correctly. The image on the screen is dim. Check if the lens is stained. If dirty, clean the lens with a soft, clean cloth. Adjust the Back Focus of the lens again. The camera does not work properly, the surface of the camera case is hot, and a black line appears on the screen. Check if you have connected the camera to a proper power source and If there is no problem with the power, turn the unit off immediately and seek assistance from our Customer Service department. The screen blinks a lot. Check if the camera is pointed toward the sun or a fluorescent lamp. Adjust the angle or location of the camera if too much light is coming into the screen. TROUBLESHOOTING: If you have trouble operating your camera, refer to the following. If the guidelines do not enable you to solve the problem, contact an authorized technician. NAME AND FUNCTION: Fixed Lens & IR LED Type BLC AGC FL ON OFF ON DC LEVEL VIDEO SWITCH ON 3 1 2 AC 24V J503 J504 AC24V J501 J502 HEATER /AUDIO J505 b a Operation Manual Guide Pattern Service Monitor Cable 75.7 100.0 142.4 101.0 37.0 47.15 Ceiling Mounting Screw L-Wrench L-Wrench Guide Pattern Dome Base Mounting Screw Dome Cover P/N:3810-0055R Rev 0 05 / 23 ※ 3/4 JIS B0202-1982 PRECAUTIONS: CONNECTION: No. #1 #2 Function Video Output Power Input Remark 1.0 Vp-p 12VDC, Max 5W/ 400mA Terminal Color Yellow Red Connecting to Monitor and Power 12VDC Power Type Camera Lay-out #1 #2 Video (Yellow) Power - 12VDC (Red) Video Output GND • The wire is polarized. • Use 12VDC power source. 360º 360º 90º Design and specifications are subject to change without notice. Need Help? Call 1.800.796.CCTV for sales, service and customer support. www.honeywellvideo.com Tilt rotation: Adjusting the vertical angle. Pan rotation: Adjusting the horizontal angle. Horizontal rotation: Adjusting the horizontal position of the screen. 1 2 3 IR LED: 850nm / 30°(24EA) Sensor 4 5 • Power Consumption: 5W • IR LED Specification: 850nm / 30°(24EA) IR LED (4mm Fixed Lens) 1 2 3 4 5 ! Do not install the camera in extreme temperature conditions. Do use the camera under conditions where temperatures are within -20°C to 45°C. Be especially careful with ventilation under high temperatures. ! Do not drop the camera or subject them to physical shocks. It can cause malfunctions to occur. ! Do not disassemble the camera. There are no user-serviceable parts inside it. ! Note When this camera is installed near wireless communication devices that emits strong electromagnetic field, irregularity such as noise on the monitor may appear.