HA ACCEPTED EN1317 COMPLIANT ROAD RESTRAINT SYSTEMS March 2011 CONTENTS: Sector Scheme Training Requirements New Products & Amendments Safety Barriers (SB) Temporary Safety Barriers (TSB) Parapets (P) Terminals (T) Lorry Mounted Crash Cushions (LMCCs) Transitions (TRANS) Miscellaneous (M) Crash Cushions (CC) Safety Barrier Gates (SBG) The HA Accepted EN1317 Compliant Road Restraint Systems List is periodically updated. To view or download the current version of this list contact: http://www.highways.gov.uk/business/8720.aspx
62
Embed
HA ACCEPTED EN1317 COMPLIANT ROAD RESTRAINT SYSTEMS · Organisation (refer to TD19/06, Sections 3.6 and 3.7). The installation of safety barriers with an ASI Class of C must be with
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
HA ACCEPTED EN1317 COMPLIANTROAD RESTRAINT SYSTEMS
March 2011
CONTENTS:
Sector Scheme Training Requirements
New Products & Amendments
Safety Barriers (SB)
Temporary Safety Barriers (TSB)
Parapets (P)
Terminals (T)
Lorry Mounted Crash Cushions (LMCCs)
Transitions (TRANS)
Miscellaneous (M)
Crash Cushions (CC)
Safety Barrier Gates (SBG)
The HA Accepted EN1317 Compliant Road Restraint Systems List is periodically updated.To view or download the current version of this list contact:
Sector Scheme Training Requirements, New Products Relisted Products & Amendments March 2011
Sector Scheme Training Requirements
Note from TD19/06:1.17 All VRS installed for use on the Trunk Road network, and on all roads in NorthernIreland, must be installed and maintained by qualified personnel in accordance with SectorSchemes 2B and 5B (see Appendix A of MCHW-1), where these schemes are applicable.VRS, such as bridge and pedestrian parapets or cast in-situ concrete barriers, that are notcovered by these Sector Schemes must be installed and maintained by suitably trainedand experienced personnel.
applications (inc. CE mark)- Hill and Smith Ltd; Double sided FlexBeam at 4.0m post spacing- SafeRoad BLG; Birsta W2 at 4.0m post spacing- Tata Steel Construction Products; Vetex N2 W4 Single Sided Safety Barrier
at 3.5m post spacing•••• Safety Barriers (Permanent and Temporary)
- Hill and Smith; TranzFlex 100 N2 FlexBeam to single sided H1/H2FlexBeam Plus Transition
Note: For further details on these systems, please see relevant section within the HAAccepted EN1317 Compliant Road Restraint Systems List.
Amendments/Other Changes
• Listing of the Asset International VarioGuard systems 1 and 2 within Class L2• SafeRoad BLG’s Phoenix (N1 and N2), SN2 and BalmerGuard parapets now CE
marked• Change of company name for CORUS CEP (to Tata Steel Construction Products)• Change of company name for CORUS Tubes (to Tata Steel Tubes Europe)• Change of contact details for Delta Bloc International (now Delta Bloc UK Ltd.)• Change of promoter details for all Delta Bloc systems from Marshalls to Delta Bloc
UK Ltd.• Change of company name for Quixote Europe (to Trinity Highway Products
International)• Change of contact address and telephone number for Sistema Limited• Change of contact details for SafeRoad BLG
Return to Contents
ASI Comment CE Marked
C The installation of safetybarriers with an ASI Class ofC must be with theagreement of the OverseeingOrganisation (refer toTD19/06, Sections 3.6 and3.7).
W1 C
W4 B
B
W4B
W5B
W4B
W5N2 A
W6
Please contact an appropriate Manufacturer/ Contractorfor details including information on construction.
W5
Please contact an appropriate Manufacturer/ Contractorfor details including information on construction.
Please contact any of the Promoters listed below fordetails including information on construction,connections and transitions.
Please contact any of the Promoters listed below fordetails including information on construction,connections and transitions.
SAFETY BARRIERS
The following Safety Barriers have been successfully tested to meet the requirements of BS EN 1317 -1 and -2 and are acceptable for use on the Highways AgencyTrunk Road Network for the Containment Performance Class and Working Width Class stated below.Please note: that all safety barriers must be installed by qualified personnel in accordance with sector scheme 2B or 21.The Safety Barriers shall comply with the manufacturers Specification, component descriptions and Installation procedures.Further information on Impact Severity Levels for the product and copies of documents and drawings can be obtained from the Promoter.
Working Width Class
The installation of safetybarriers with an ASI Class ofC must be with theagreement of the OverseeingOrganisation (refer toTD19/06, Sections 3.6 and3.7).
Name and Address of Promoter
Please contact any of the Promoters listed below fordetails including information on construction,connections and transitions.
Double Rail OpenBox Beam (DROBB)
With post centres at 2.4mthen the Working Width Class
Double Sided OpenBox Beam (DSOBB)
Higher VerticalConcrete Barrier(HVCB)
N2
Vertical ConcreteBarrier (VCB)
N2
Please contact any of the Promoters listed below fordetails including information on construction,connections and transitions.
With post centres at 3.2m theWorking Width Class is:
With post centres at 1.2m theWorking Width Class is:
With post centres at 2.4m theWorking Width Class is:
With post centres at 1.2m theWorking Width Class is:
Safety Barrier Type Containment Performance Class
H1
Single SidedTensionedCorrugated Beam(SSTCB)
Single Sided OpenBox Beam (SSOBB)
H4a
N2
Safety Barriers SB 1 March 2011
ASI Comment CE MarkedWorking Width Class Name and Address of PromoterSafety Barrier Type Containment Performance Class
Unknown
W6
Clipstone Services Limited Tata Steel Construction Products Tata Steel Tubes EuropeUnits J & K Llanwern Works PO Box 101Clipstone Holding Centre Newport Weldon RoadClipstone Village South Wales CorbyMansfield NP19 4QZ NorthantsNottinghamshire NN17 5UANG21 9AP Tel. 01633 290011 Tel. 01536 402121Tel. 01623 420188 email: [email protected] email:[email protected]
Hill and Smith Ltd. SafeRoad BLG Ltd.Springvale Avenue Dragonby ValeBilston Enterprise ParkWolverhampton Manaberg WayWV 0QL Scunthorpe
Please contact any of the Promoters listed below fordetails including information on construction,connections and transitions.
Double SidedTensionedCorrugated Beam(DSTCB)
With post centres at 3.2m theWorking Width Class is:
The Promoters for the above Double Rail Open Box Beam (DROBB), Single Sided Open Box Beam (SSOBB), Double Sided Open Box Beam (DSOBB), Single Sided Tensioned Corrugated Beam(SSTCB) and Double Sided Tensioned Corrugated Beam (DSTCB) are listed below. Please contact these Promoters for all enquiries concerning these safety barrier systems and associatedconnections and transitions and detailed and general arrangement drawings.
N2
Safety Barriers SB 2 March 2011
ASI Comment CE MarkedWorking Width Class Name and Address of PromoterSafety Barrier Type Containment Performance Class
System SpenglerSingle Sided PrecastConcrete Barrier,Type 81 (includingBridge Capinstallation)
The installation of safetybarriers with an ASI Class ofC must be with theagreement of the OverseeingOrganisation (refer toTD19/06, Sections 3.6 and3.7).
The installation of safetybarriers with an ASI Class ofC must be with theagreement of the OverseeingOrganisation (refer toTD19/06, Sections 3.6 and3.7).
Bilston
N2
System Spengler'URBAN' Single SidedPrecast ConcreteBarrier, (ModifiedSystem SpenglerType 85-2
Asset International (A Division of Hill and Smith)
The installation of safetybarriers with an ASI Class ofC must be with theagreement of the OverseeingOrganisation (refer toTD19/06, Sections 3.6 and3.7).
System SpenglerDouble Sided PrecastConcrete Barrier('B35') (height 0.81 +0.04m)
System SpenglerPrecast ConcreteBarrier, TroughConstruction withFilling
Safety Barriers SB 3 March 2011
ASI Comment CE MarkedWorking Width Class Name and Address of PromoterSafety Barrier Type Containment Performance Class
W2 B Asset International (A Division of Hill and Smith)Springvale AvenueBilstonWolverhamptonWV14 0QLTel. 01902 499402Fax. 01902 402104email: [email protected] Site: www.asset-vrs.co.uk
Bilston
Asset International (A Division of Hill and Smith)
Note - where there is nodifference in level betweenadjoining carriageways andwhere the actual width of thebarrier is less than 0.6m widethe Working Width Class is:
N2H1 or H2
Variable EmbeddedConcrete Step Barrier(0.9m High minimum)Slip formed ConcreteSystem (Minimum60mm embedment)
Note - where there is adifference in level betweenadjoining carriageways of notmore than 300mm and wherethe actual width of the barrieris less than 0.6m wide theWorking Width Class is:
Note - where there is adifference in level betweenadjoining carriageways of notmore than 300mm and wherethe actual width of the barrieris greater than 0.6m but lessthan 1.0m wide the WorkingWidth Class is:
Note - where there is nodifference in level betweenadjoining carriageways andwhere the barrier width isgreater than 0.6m but lessthan 1.0m wide the WorkingWidth Class is:
Safety Barriers SB 6 March 2011
ASI Comment CE MarkedWorking Width Class Name and Address of PromoterSafety Barrier Type Containment Performance Class
Note - where there is adifference in level betweenadjoining carriageways of notmore than 300mm and wherethe actual width of the barrieris less than 0.6m wide theWorking Width Class is:
Note - where there is nodifference in level betweenadjoining carriageways andwhere the barrier width isgreater than 0.6m but lessthan 1.0m wide the WorkingWidth Class is:
N2
Surface MountedConcrete Step Barrier(0.9m High fixedprofile) Slip formedConcrete System
Note - where there is adifference in level betweenadjoining carriageways of notmore than 300mm and wherethe barrier width is greaterthan 0.6m but less than 1.0mwide the Working Width Classis:
Note - where there is nodifference in level betweenadjoining carriageways andwhere the actual width of thebarrier is less than 0.6m widethe Working Width Class is:
H1 or H2
N2 or H1 or H2H2
Safety Barriers SB 7 March 2011
ASI Comment CE MarkedWorking Width Class Name and Address of PromoterSafety Barrier Type Containment Performance Class
W4 B Delta Bloc United Kingdom Ltd1200 Century WayThorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
W6 B Delta Bloc United Kingdom Ltd1200 Century WayThorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
N2 W4 B Delta Bloc United Kingdom Ltd1200 Century WayThorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
W4 A Delta Bloc United Kingdom Ltd1200 Century WayThorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
W6 B Delta Bloc United Kingdom Ltd1200 Century WayThorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
Delta Bloc DB65S/6m(K120S)
Delta Bloc DB80/4m(K180)
N1
Note: Only permitted for use onroads where road works are beingundertaken and a speed limit ofless than 50 mph is operative.
Delta Bloc DB80/4m(K180)
H1
Delta Bloc DB65S/6m(K120S)
H1
N2
Delta Bloc DB80/4m(K120S)
Safety Barriers SB 8 March 2011
ASI Comment CE MarkedWorking Width Class Name and Address of PromoterSafety Barrier Type Containment Performance Class
N2 W3 B Delta Bloc United Kingdom Ltd1200 Century WayThorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
H2 W1 B Delta Bloc United Kingdom Ltd1200 Century WayThorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
H2 W4 B Delta Bloc United Kingdom Ltd1200 Century WayThorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
Delta Bloc DB80E/6m H2 W1 C Delta Bloc United Kingdom Ltd(K150S) 1200 Century Way
Thorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
H2 W6 C Delta Bloc United Kingdom Ltd1200 Century WayThorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
The installation of safetybarriers with an ASI Class ofC must be with theagreement of the OverseeingOrganisation (refer toTD19/06, Sections 3.6 and3.7).
The installation of safetybarriers with an ASI Class ofC must be with theagreement of the OverseeingOrganisation (refer toTD19/06, Sections 3.6 and3.7).
Delta Bloc DB80AS-R/6m (K180)
Delta Bloc DB80AS-E/6m (K180S)
Delta Bloc DB90Step/6m (K220)
Delta Bloc DB80/6m(K150S)
Safety Barriers SB 9 March 2011
ASI Comment CE MarkedWorking Width Class Name and Address of PromoterSafety Barrier Type Containment Performance Class
H2 W5 A Delta Bloc United Kingdom Ltd1200 Century WayThorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
Delta Bloc DB100/6m N2 W6 B Delta Bloc United Kingdom Ltd(K250) 1200 Century Way
Thorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
Delta Bloc DB100/6m H4a W6 B Delta Bloc United Kingdom Ltd(K250) 1200 Century Way
Thorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
Delta Bloc DB100/6m H1 W6 B Delta Bloc United Kingdom Ltd(K250) 1200 Century Way
Thorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
A Francesco TessariIMEVA82 100 BeneventoLocalita Ponte ValentinoArea Industriale ASIZona 75ItalyTel. 0039 08 24481211email: [email protected]
N2
Delta BlocDB100S/6m (K220)
IMEVA N2 VergeSafety Fence
With post centres at 3.375mthe Working Width Class is:
W5
Safety Barriers SB 10 March 2011
ASI Comment CE MarkedWorking Width Class Name and Address of PromoterSafety Barrier Type Containment Performance Class
W4 B Haitsma BetonPinksterbloemstraat 2Postbus 79288 ZG KootstertilleThe Netherlands
With post centres at 1.2m theWorking Width Class is:
With post centres at 1.6m the
With post centres at 5.0m theWorking Width Class is:
The installation of safetybarriers with an ASI Class ofC must be with theagreement of the OverseeingOrganisation (refer toTD19/06, Sections 3.6 and3.7).
Working Width Class is:
With post centres at 3.2m theWorking Width Class is:
With post centres at 2.4m theWorking Width Class is:
With post centres at 2.0m the
With post centres at 4.0m theWorking Width Class is:
H1
With post centres at 0.8m theWorking Width Class is:
Working Width Class is:
With post centres at 2.0m theWorking Width Class is:
With post centres at 2.8m theWorking Width Class is:
With post centres at 2.0m theWorking Width Class is:
Safety Barriers SB 14 March 2011
ASI Comment CE MarkedWorking Width Class Name and Address of PromoterSafety Barrier Type Containment Performance Class
ZoneGuard N2 W6 B Hill and Smith Ltd.Springvale AvenueBilstonWolverhamptonWV 0QLTel. 01902 499400Fax: 01902 499419email: [email protected] site: www.hill-smith.co.uk
N2 A Holgate Infrastructure & Motorway Services137 Gelderd Road
W5 B Sistema Construction (UK) Ltd.Unit CShepherds Grove Industrial Estate (East)StantonBury St EdmundsSuffolkIP31 2BFTel. 01359 251 248Fax. 01359 251 201Mobile. 07740 122 982email: [email protected] email: [email protected]
B Sistema Construction (UK) Ltd.Unit CShepherds Grove Industrial Estate (East)StantonBury St EdmundsSuffolkIP31 2BFTel. 01359 251 248Fax. 01359 251 201Mobile. 07740 122 982email: [email protected] email: [email protected]
With post centres at 4.0m theWorking Width Class is:
W5N2 and H3
Sistema SteelgardBarrier
N2
Sistema SteelgardCentral ReserveBarrier
H4a
SCT 'DUCOS' SingleSided CompositeTimber and SteelClass N2 SafetyBarrier
ESP Profile A, 2mpost spacing
Safety Barriers SB 19 March 2011
ASI Comment CE MarkedWorking Width Class Name and Address of PromoterSafety Barrier Type Containment Performance Class
B Sistema Construction (UK) Ltd.Unit CShepherds Grove Industrial Estate (East)StantonBury St EdmundsSuffolkIP31 2BFTel. 01359 251 248Fax. 01359 251 201Mobile. 07740 122 982email: [email protected] email: [email protected]
W6 A Sistema Construction (UK) Ltd.Unit CShepherds Grove Industrial Estate (East)StantonBury St EdmundsSuffolkIP31 2BFTel. 01359 251 248Fax. 01359 251 201Mobile. 07740 122 982email: [email protected] email: [email protected]
W7 B Sistema Construction (UK) Ltd.Unit CShepherds Grove Industrial Estate (East)StantonBury St EdmundsSuffolkIP31 2BFTel. 01359 251 248Fax. 01359 251 201Mobile. 07740 122 982email: [email protected] email: [email protected]
W2 A Sistema Construction (UK) Ltd.Unit CShepherds Grove Industrial Estate (East)StantonBury St EdmundsSuffolkIP31 2BFTel. 01359 251 248Fax. 01359 251 201Mobile. 07740 122 982email: [email protected]
END OF SAFETY BARRIER SECTION - RETURN TO CONTENTS
With post centres at 1.5m theWorking Width Class is:
The installation of safetybarriers with an ASI Class ofC must be with theagreement of the OverseeingOrganisation (refer toTD19/06, Sections 3.6 and3.7).
With post centres at 4.0m theWorking Width Class is:
With post centres at 1.5m theWorking Width Class is:
H2
N2
H2
Protect 365 N2 SafetyFence
N2
With post centres at 4.0m theWorking Width Class is:
Vulcan Safety Barrier
H1
Tubosider 3NTU-brl.16 Class N2Hardshoulder SafetyBarrier
Tubosider 2NTU-brl.23 Class H1/H2Hardshoulder SafetyBarrier
TSS Softbaer H2FreestandingConcrete Barrier
H2
With post centres at 2.0m theWorking Width Class is:
N2
Safety Barriers SB 24 March 2011
ASI CommentH1 W7 B Ardee Precast Concrete Limited
Town ParksN1 W3 A Ardee
Co. LouthIrelandTel. +353 41 6856372Fax. +353 41 6857216email: [email protected] Site: www.ardeeprecastconcrete.comAsset International (A Division of Hill and Smith)
Note: N1 system only permitted foruse on roads where a speed limitof less than 50 mph is operative.
System SpenglerTransportable DoubleSided PrecastConcrete Barrier(height 0.81m)
For a tested length of 60mb t d h d
TEMPORARY SAFETY BARRIERS
The following Temporary Safety Barriers have been successfully tested to meet the requirements of BS EN 1317 -1 and -2 and have been accepted foruse on the Highways Agency Trunk Road Network for the Containment Performance Class and Working Width Class stated below.Please note: that all safety barriers must be installed by qualified personnel in accordance with sector scheme 2B.The Temporary Safety Barriers shall comply with the manufacturers Specification, component descriptions and Installation procedures.Further information on Impact Severity Levels for the product and copies of documents and drawings can be obtained from the Promoter.
Safety Barrier Type Containment Performance Class Working Width Class Name and Address of Promoter
between end anchors, andanchored in accordance with theEN1317 compliant test, theworking width class shall be:
Sided Safety Barrier -SYSTEM No. 1
Springvale AvenueBilston
H2
Note: For a different installation lengthplease contact the Promoter forinformation concerning the WorkingWidth of the system.
Temporary Safety Barriers TB 24 March 2011
ASI CommentSafety Barrier Type Containment Performance Class Working Width Class Name and Address of PromoterAsset International (A Division of Hill and Smith)Springvale AvenueBilston
ASI CommentSafety Barrier Type Containment Performance Class Working Width Class Name and Address of PromoterAsset International (A Division of Hill and Smith)Springvale AvenueBilstonWolverhamptonWV14 0QL
W6 B Delta Bloc United Kingdom Ltd1200 Century WayThorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
N2 W3 B Delta Bloc United Kingdom Ltd1200 Century WayThorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
H1Delta Bloc DB80/4m(K180)
Delta Bloc DB80/6m(K150S)
Temporary Safety Barriers TB 27 March 2011
ASI CommentSafety Barrier Type Containment Performance Class Working Width Class Name and Address of PromoterH2 W1 B Delta Bloc United Kingdom Ltd
1200 Century WayThorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
H2 W4 B Delta Bloc United Kingdom Ltd1200 Century WayThorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected]
Web site: www.deltabloc.co.ukDelta Bloc DB80E/6m H2 W1 C Delta Bloc United Kingdom Ltd(K150S) 1200 Century Way
Thorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06
The installation of safetybarriers with an ASI Classof C must be with theagreement of theOverseeing Organisation(refer to TD19/06,Sections 3.6 and 3.7).
H2 W6 C Delta Bloc United Kingdom Ltd1200 Century WayThorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
H2 W5 A Delta Bloc United Kingdom Ltd1200 Century WayLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
)
Delta Bloc DB90Step/6m (K220)
The installation of safetybarriers with an ASI Classof C must be with theagreement of theOverseeing Organisation(refer to TD19/06,Sections 3.6 and 3.7).
Delta BlocDB100S/6m (K220)
Temporary Safety Barriers TB 28 March 2011
ASI CommentSafety Barrier Type Containment Performance Class Working Width Class Name and Address of PromoterDelta Bloc DB100/6m N2 W6 B Delta Bloc United Kingdom Ltd(K250) 1200 Century Way
Thorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
Delta Bloc DB100/6m H4a W6 B Delta Bloc United Kingdom Ltd(K250) 1200 Century Way
Thorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
Delta Bloc DB100/6m H1 W6 B Delta Bloc United Kingdom Ltd(K250) 1200 Century Way
Thorpe Park Business ParkColtonLeeds LS15 8ZATel. 08453 04 07 05Fax. 08453 04 07 06email: [email protected] site: www.deltabloc.co.uk
W4 A Eurovia Beton12, Avenue du Juillet91412 Dourdan CedexFranceTel. (33) 01 60815200/(33) 01 64593184email: [email protected] site: www.eurovia.com
N1
Note: Only permitted for use onroads where road works are beingundertaken and a speed limit ofless than 50 mph is operative.
Eurovia Beton 2mTransportableConcrete Barrier
Temporary Safety Barriers TB 29 March 2011
ASI CommentSafety Barrier Type Containment Performance Class Working Width Class Name and Address of PromoterW3 B Hardstaff Barriers
The installation oftemporary safety barrierswith an ASI Class of Cmust be with theagreement of theOverseeing Organisation(refer to TD19/06,Sections 8.5 and 8.6).
The installation oftemporary safety barrierswith an ASI Class of Cmust be with theagreement of theOverseeing Organisation(refer to TD19/06,Sections 8.5 and 8.6).
REBLOC RB80_8 N2 W3 B REBLOC GmbHWeinerstrasse 662A-3571 Gars am KampGERMANYTel. +43(2985)30922-2902Fax. +43(2985)30922-2901email: [email protected] site: www.rebloc.com
W8 A Rhino Barrier Systems Ltd.
The installation oftemporary safety barrierswith an ASI Class of Cmust be with theagreement of theOverseeing Organisation(refer to TD19/06,Sections 8.5 and 8.6).
Note: Only permitted for use onroads where road works are beingundertaken and a speed limit ofless than 50 mph is operative.
Water Filled Barrier
Temporary Safety Barriers TB 32 March 2011
ASI CommentSafety Barrier Type Containment Performance Class Working Width Class Name and Address of PromoterSafeRoad BLGDragonby ValeEnterprise ParkManaberg WayScunthorpe
W8 B North LincolnshireDN15 8XFTel. 01724 289119email: [email protected]
Note: For a differentinstallation length pleasecontact the Promoter forinformation concerning theWorking Width of the system.
For a tested length of 64mbetween end anchors, andanchored in accordance with theEN1317 compliant test, theworking width class shall be:
Temporary Safety Barriers TB 33 March 2011
ASI CommentSafety Barrier Type Containment Performance Class Working Width Class Name and Address of PromoterW6 A Trinity Highway Products International
The following Parapets have been successfully tested to meet the requirements of BS EN 1317 -1 and -2 and have been accepted for use on the Highways AgencyTrunk Road Network for the Containment Performance Class and Working Width Class stated below.Please note: that all parapets must be installed by qualified personnel in accordance with sector scheme 5B.The parapets shall comply with the manufacturers Specification, component descriptions and Installation procedures.Further information on Impact Severity Levels for the product and copies of documents and drawings can be obtained from the Promoter.
ASI Comment CE MarkedContainment Performance ClassParapet Type Working Width Class Name and Address of PromoterH2 W4 A Holgate Infrastruture and Motorway Services
The following Terminals for safety barriers have been successfully tested to meet the requirements of DD ENV 1317 - 4 and have been accepted for use onthe Highways Agency Trunk Road Network for the Performance Class and Permanent Lateral Displacement Zone (PLDZ) Class Code stated below.The Terminals shall comply with the manufacturers Specification, component descriptions and Installation procedures.Please note: that all safety barriers must be installed by qualified personnel in accordance with sector scheme 2B.Additional information on Exit Box and Impact Severity Levels for the product and copies of documents and drawings can be obtained from the Promoter.Installers shall have successfully undertaken suitable training for the system to be installed.
Note: please refer to Table 6, DD ENV 1317 - 4 for PLDZ and Class Codes for terminals. The values of Displacement (measured in metres) Da and Dd areconverted to Class Code x and y. Therefore Class Code D1.1 (where 'D' is displacement) represents 0.5m displacement (x), measured from the traffic faceof the barrier towards the traffic, and 1.0m (y) measured from the traffic face of the barrier to the rear of the barrier. D1.3 represents a displacement of 0.5min front of the barrier and 3.5m to the rear of the barrier.
Performance Class PLDZ Class Code Name and Address of Promoter Comments
Terminals T 41 March 2011
Exit BoxClass/Vehicle
Redirection Zone
ASITerminal Type Performance Class PLDZ Class Code Name and Address of Promoter Comments
Terminus CEN P4 Z2 A Energy Absorption Systems IncCrown HouseCrown StreetIpswichSuffolkIP1 3HS
P1 Z1 A Hill and Smith Ltd.Springvale AvenueBilstonWolverhamptonWV 0QLTel. 01902 499400Fax: 01902 499419email: [email protected] site: www.hill-smith.co.uk
50mph or more, verge only
Less than 50mph, or on thedeparture end of a safety barriernot facing oncoming traffic wherethe speed limit is 50mph or more.
Less than 50mph, or on thedeparture end of a safety barriernot facing oncoming traffic wherethe speed limit is 50mph or more.
Less than 50mph, or on thedeparture end of a safety barriernot facing oncoming traffic wherethe speed limit is 50mph or more.
Hill and Smith 'SafetyLine' Wire RopeSafety FenceTerminal
Flex-Beam SingleSided P1 EndTerminal
D.1.1
D.1.1
D.1.1
D.1.3Trinity Euro ET EndTerminal
Flex-Beam DoubleSided P1 EndTerminal
Terminals T 43 March 2011
Exit BoxClass/Vehicle
Redirection Zone
ASITerminal Type Performance Class PLDZ Class Code Name and Address of Promoter Comments
P4 Z2 B Hill and Smith Ltd.Springvale AvenueBilstonWolverhamptonWV14 0QLTel. 01902 499400Fax. 01902 499419email: [email protected]
P4 Z1 B Marcegaglia buildtech S.r.lNew RoadNethertonDudleyWest MidlandsDY2 8TA
Less than 50mph, or on thedeparture end of a safety barriernot facing oncoming traffic wherethe speed limit is 50mph or more.
Trinity Euro BXTTerminal
D.1.2 50mph or more
Terminals detailed in the NPSBS are deemed acceptable for use on the Highways Agency Trunk Road Network on roads with a speed limit less than 50mph. In addition the terminals can be used on the departure end of safety barriers where the terminal does not face oncoming traffic and the speed limit is50mph or more.These terminals do not need a Departure from Standard submission, as they have proven in-service use over a number of years.Please contact the Promoter's of DROBB, OBB and TCB listed in the Safety Barrier section for further information.Installers shall have successfully undertaken suitable training for the system to be installed.
Trinity MPS-350 Lorry MountedCrash Cushion(For use on roads with aspeed limit of 70mph or less)
LORRY MOUNTED CRASH CUSHIONS
The following Lorry Mounted Crash Cushions (LMCC) meet the requirements of TD 49/07 and hence, have demonstratedcompliance with a 1500kg car impact at the speed of the performance class. They may be used on the Highway AgencyTrunk Road Network provided that a special dispensation order known as a Vehicle Special Order (VSO) is obtained fromthe Department for Transport.In addition a Vehicle Inspectorate Form VTG 10 will need to be filed if the LMCC is fitted with an auto impact brake system.The LMCC shall comply with the manufacturers Specification, component descriptions and Installation procedures. Copiesof documents and drawings can be obtained from the Promoter.
Name and Address of PromoterVehicle AttenuatorsScorpion Lorry Mounted CrashCushion(For use on roads with aspeed limit of 70mph or less)
Lorry Mounted Crash Cushions LMCC 45 March 2011
Name and Address of PromoterVehicle AttenuatorsVorteq Trailer Trinity Highway Products International - represented by:
King Highway Products Ltd.EriversideMarket HarboroughLeicestershireLE16 7PX
H2 W4 C Delta Bloc United Kingdom Ltd1200 Century WayThorpe Park Business ParkColtonLeeds LS15 8ZATel. 0845 30 40 705Fax. 0845 30 40 706email: [email protected] site: www.deltabloc.co.uk
BRITRANS' OpenBox Beam to WireRope Safety FenceTransition
Name and Address of Promoter
Brifen (A Division of Hill and Smith)
Use of thistransition must bewith the agreementof the OverseeingOrganisation (referto TD19/06, Section6.6).
TRANSITIONS
Transion Type Containment Performance Class
N2
DB SafeLinkTransition (DB100Sto DB90 Step)
The following Transitions have been successfully tested to meet the requirements of ENV 1317 - 4 and has been accepted for use on the HighwaysAgency Trunk Road Network for the Containment Performance Class and Working Width Class stated below.The Transition shall comply with the manufacturers Specification, component descriptions and Installation procedures. Further information onImpact Severity Levels for the product and copies of documents and drawings can be obtained from the Promoter.Installers shall have successfully undertaken suitable training for the system to be installed.
Transitions detailed in the NPSBS (Revision 1) are deemed acceptable for use on the Highways Agency Trunk Road Network, without the need fora Departure from Standard submission, as they have proven in-service use over a number of years.Please contact Promoter's of DROBB, OBB and TCB listed in the Safety Barrier Section for further information.
TSS Vario -Transition betweenGerman B-profilesafety fence and TSSSoftbaer concretebarrier
Transitions Trans 51 March 2011
ASIBIKEGUARD A
MaidstoneKentME14 3HT
Web site: www.highwaycare.co.ukFlexGuard Hill and Smith Ltd.
The following products have been accepted for use on the Highways Agency Road Network.
(Motorcyclist Protection Systemfitted to safety barriers)
Motorcyclist Protection System fitted toFlexBeam/FlexBeam Plus (both single anddouble sided versions of these systems), theHill and Smith H1/H2 safety barrier, and theBriflex vehicle restraint system.
(Motorcyclist Protection Systemfitted to safety barriers)
Comments
BIKEGUARD may be fitted to any UKsystem listed in the Non-Proprietary SafetyBarrier Systems (NPSBS). It may also befitted to any other system in the HighwaysAgency Approved Road Restraint SystemList providing that Highway Care Limited firstobtains the approval of thePromoter/Manufacturer of the safety barriersystem BIKEGUARD is to be attached to.
The Highlands
Miscellaneous M 52 March 2011
ASI CE MarkedRe - Direction Zone Class - Z1 A Asset International (A Division of Hill and Smith) YES
Springvale AvenueLateral Displacement Zone Class - D1 Bilston
Vecu-Stop Re-Directionaland Bi-Directional CrashCushion - Model 2.13P
100kph
Euro - Tracc Re-Directionaland Bi-Directional CrashCushion
Vecu-Stop Re-Directionaland Uni-Directional CrashCushion - Model 2.14P andModel 4.14T
(For use on roads witha speed limit greater
than 50mph )
(For use on roads witha speed limit greater
than 50mph)
110kph
110kph
CRASH CUSHIONS
Crash Cushion Performance Level Name and Address of PromoterZone Classes
The following Crash Cushions have been successfully tested to meet the requirements of BS EN 1317 - 3 and have been accepted for use on theHighways Agency Trunk Road Network for the Performance Level and Zone Classes stated below.Please note: that all safety barriers must be installed by qualified personnel in accordance with sector scheme 2B.The Crash Cushions shall comply with the manufacturers Specification, component descriptions and Installation procedures. Copies ofdocuments and drawings can be obtained from the Promoter.
Crash Cushions CC 53 March 2011
ASI CE MarkedCrash Cushion Performance Level Name and Address of PromoterZone ClassesRe - Direction Zone Class - Z1 B Asset International (A Division of Hill and Smith) YES
Springvale Business and Industrial ParkLateral Displacement Zone Class - D1 Bilston
Asset International (A Division of Hill and Smith)Working Width Class
SAFETY BARRIER GATES
The following Safety Barrier Gates have been successfully tested to meet the requirements of BS EN 1317- 1 and 2 and DD ENV1317 - 4 and have been accepted for use on the Highways Agency Trunk Road Network for the Containment Performance Classand Working Width Class stated below.The Safety Barrier Gates shall comply with the manufacturers Specification, component descriptions and Installation procedures.Further information on Impact Severity Levels for the product and copies of documents and drawings can be obtained from thePromoter.Installers shall have successfully undertaken suitable training for the system to be installed.
Name and Address of Promoter
H2
H1Springvale Avenue
Safety Barrier Gates SBG 56 March 2011
ASIW6 A Snoline spa, represented by:
Highway Care Ltd.The HighlandsDetling HillDetling HillMaidstoneKentME14 3HT
The following Safety Barrier Gates have the same profile and performance characteristics of their compliant BS EN 1317 safetybarriers which have been tested to meet the requirements of BS EN 1317 - 1 and 2 and are deemed acceptable for use on theHighways Agency Trunk Road Network for the Containment Performance Class and Working Width Class stated below.The Safety Barrier Gates shall comply with the manufacturers Specification, component descriptions and Installation procedures.Further information on Impact Severity Levels for the product and copies of documents and drawings can be obtained from thePromoter.
Containment Performance Class Working Width Class
Safety Barrier Gates SBG 58 March 2011
ASIW5 Highway Care Ltd.
The HighlandsW8 Detling Hill
DetlingMaidstoneKentME14 3HT
Web site: www.highwaycare.co.uk
END OF SAFETY BARRIER GATE SECTION - RETURN TO CONTENTS
Safety Barrier Gate Containment Performance Class Working Width Class Name and Address of Promoter