GD&T SELF EVALUATION TEST - DIFFICULTY LEVEL - 1 (of 10) Reference – ASME Y14.5M - 1994 by David Hebert (GD&T Senior Level Certified but not associated with ASME) Test # - 1994-TL1-T01A- RevA If errors are found, or if you have any questions, please let me know…….. http:/www/mygdtsite.com WIP - for review on ly 08/14/202 2 1 To use these test you simply “run” the slide show and use the down arrow key to navigate. If you find any mistakes please let me know and I will fix them and post the updated file to the www.mygdtsite.com . The part number above reflects the current rev. Hope this helps, let me know! Dave Hebert (Senior Level GD&T Professional) Note: these tests are not associated with ASME
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
GD&T SELF EVALUATION TEST - DIFFICULTY LEVEL - 1 (of 10)Reference – ASME Y14.5M - 1994 by David Hebert (GD&T Senior Level Certified but not associated with ASME) Test # - 1994-TL1-T01A-RevA
If errors are found, or if you have any questions, please let me know…….. http:/www/mygdtsite.com
WIP - for
review only
04/11/2023 1
To use these test you simply “run” the slide show and use the down arrow key to navigate. If you find any mistakes please let me know and I will fix them and post the updated file to the www.mygdtsite.com. The part number above reflects the current rev. Hope this helps, let me know!
Dave Hebert (Senior Level GD&T Professional) Note: these tests are not associated with ASME
GD&T SELF EVALUATION TEST - DIFFICULTY LEVEL - 1 (of 10)Reference – ASME Y14.5M - 1994 by David Hebert (GD&T Senior Level Certified but not associated with ASME) Test # - 1994-TL1-T01A-RevA
If errors are found, or if you have any questions, please let me know…….. http:/www/mygdtsite.com
WIP - for
review only
START HERE & WORK DOWN
04/11/2023 2
Match the symbol to the name. Use the down arrow key to navigate through the test.
Appendix CASME 1994 Y14.5M
GD&T SELF EVALUATION TEST - DIFFICULTY LEVEL - 1 (of 10)Reference – ASME Y14.5M - 1994 by David Hebert (GD&T Senior Level Certified but not associated with ASME) Test # - 1994-TL1-T01A-RevA
If errors are found, or if you have any questions, please let me know…….. http:/www/mygdtsite.com
WIP - for
review only
8
START HERE & WORK DOWN
04/11/2023
Match the symbol to the name, press the down arrow key to begin.
PerpendicularityAngularityParallelismCircularityAll around Free StateBasic DimensionTrue PositionCircular RunoutRegardless of Feature SizeFlatnessCylindricityTangent Plane Diameter Reference Maximum Material ConditionProfile of a line Least Material ConditionTotal RunoutStraightnessProfile of a surfaceConcentricitySymmetryProjected Tolerance ZoneDatum Feature
1
2
3
4
7
5
6
9
10
11
1213
14
15
16
17
18
19
20
21
22
23
25
24
3
Appendix CASME 1994 Y14.5M
GD&T SELF EVALUATION TEST - DIFFICULTY LEVEL - 1 (of 10)Reference – ASME Y14.5M - 1994 by David Hebert (GD&T Senior Level Certified but not associated with ASME) Test # - 1994-TL1-T01A-RevA
If errors are found, or if you have any questions, please let me know…….. http:/www/mygdtsite.com
WIP - for
review only
Identify the following:
1. PROFILE (two of them)2. FORM (four of them)3. RUNOUT (two of them)4. LOCATION (three of them)5. ORIENTATION (three of them)
04/11/2023
Please identify the following types of Controls in the order listed. Note: In an effort to avoid rote memorization, the order shown in this chart is different than those listed in the Standard’s chart.
ProfileProfile
FormFormFormForm
RunoutRunout
LocationLocationLocation
OrientationOrientationOrientation
4
Fig 3.1ASME 1994 Y14.5M
GD&T SELF EVALUATION TEST - DIFFICULTY LEVEL - 1 (of 10)Reference – ASME Y14.5M - 1994 by David Hebert (GD&T Senior Level Certified but not associated with ASME) Test # - 1994-TL1-T01A-RevA
If errors are found, or if you have any questions, please let me know…….. http:/www/mygdtsite.com
WIP - for
review only
Which of these groups of Tolerances are:
1. For RELATED features2. For INIDIVIDUAL features3. For INDIVIDUAL or
RELATED features.
04/11/2023
ProfileProfile
FormFormFormForm
RunoutRunout
LocationLocationLocation
OrientationOrientationOrientation
5
- requires RELATED FEATURES- requires RELATED FEAURES- requires RELATED FEATURES
- requires INDIVIDUAL FEATURES - requires INDIVIDUAL FEATURES- requires INDIVIDUAL FEATURES- requires INDIVIDUAL FEATURES
- requires RELATED FEATURES- requires RELATED FEAURES- requires RELATED FEATURES
- requires RELATED FEATURES- requires RELATED FEAURES
- requires RELATED or INDIVIDUAL- requires RELATED or INDIVIDUAL
Identify the type of feature dependence in the following order:1. FORM2. ORIENTATION3. PROFILE4. RUNOUT5. LOCATION
FEATURE OPTIONS:
* RELATED* INIDIVIDUAL
* INDIVIDUAL or RELATED
Fig 3.1ASME 1994 Y14.5M
Related Documents
