Game Frame and Web Assembly Instructions 3.9.11

Game Frame Assembly Instructions # 71327

Game FrameGame FrameGame FrameGame Frame

with Webwith Webwith Webwith Web

Assembly InstructionsAssembly InstructionsAssembly InstructionsAssembly Instructions #71327

Game Frame Assembly Instructions # 71327

Project Adventure’s Game Frame and Web Assembly Instructions Included:

• 2 sets of Legs (2 pieces per plastic bag)

• 2 sets of Crossbars (3 pieces per plastic bag)

• 1 set of Bases (2 pieces per plastic bag)

• 1 Spider’s Web

• 2 Game Frame decals

• 1 nylon bag for storage

What you will need:

• Flathead screwdriver

For best results, assemble frame on a large flat surface. The frame measures 10’W x 6’H

when fully assembled and stood up.

Each plastic bag is labeled with the corresponding piece of the frame. Save the bags for

easy, organized storage.

1. Take one of the bags marked CROSSBARS and remove the 3 poles inside.

Screw the three poles together by matching the colored dots to each other. Be

sure all clips are facing inward before fully tightening.

2. These three pieces put together can make either the top or the bottom of the

frame. Make sure there is knob at each end of the CROSSBAR. Set this pole

aside on a flat surface.

3. Repeat step #1 for the 2nd

set of CROSSBARS. Set this crossbar aside on a flat

surface opposite the first crossbar, as together they make the top and bottom of

the frame.

4. The next pieces to assemble are the LEGS or sides of the frame. These pieces run

vertically and attach at the ends of the CROSSBARS to make corners.

5. To assemble the LEGS screw the 2 pieces together while making sure to align the

clips on each piece through out the LEG, facing-inward. Set this piece aside on a

flat surface.

6. Repeat step #4 for the 2nd

LEG. Set aside opposite the first LEG.

7. On a flat surface, lay out the 2 CROSSBARS and the 2 LEGS so that they make a

rectangle on the floor with the LEGS on either side and the CROSSBARS along

the top and bottom. The capped ends of the LEGS face toward the top of the

frame.

8. Remove the knobs on both ends of the CROSSBARS and set aside. Also, remove

the flathead screw in the bottom end of each LEG and set aside.

9. Starting on one side of the frame, at the top, fit the LEG and CROSSBAR pieces

together and replace the knobs. Do this for both sides at the top only. Be sure all

clips are facing inward before securing the knobs. 10. Repeat this process for the remaining 3 corners of the frame.

11. With the rectangle shape of the frame secured at all corners, it is time to put the

BASES (feet) on the frame. The BASES attach to the bottom left and bottom

right of the frame with the flathead screws that were set-aside in step #7.

Game Frame Assembly Instructions # 71327

12. Each base has a ¼” sleeve attached in the middle. Place the middle of the BASE

into the bottom end of one LEG. You will have to lift the corner of the frame off

the ground to get the BASE to sit in the hole perpendicular to the LEG.

13. Slide the flathead screw through the hole in the BASE and then use a flathead

screwdriver (not included) to tighten the BASE to the LEG.

14. Repeat steps #11 & 12 for the second and final BASE.

15. With both BASES fastened securely to the LEGS, slowly stand up the entire

frame, resting it on the BASES (feet). Leave frame standing up.

16. Gently unfold the web contained in the protective wrap onto a flat surface. You

may want to save the wrap for safe and easy future storage of the web. It may be

easier for two people to attach the web to the frame together.

17. The design of the web has an “X” through the center of it with attachment points

at all 4 corners of the frame. The “X” may be in 2 different colors. (Red and

yellow most likely) See Diagram A.

18. Attach one ring of the “X” into each corner clip of the frame. DO NOT PULL

AND RELEASE THE WEB QUICKLY! See warning below. 19. The rest of the web is built around and through the “X” shape. Attach one ring at

a time to the remaining 4 clips that are in the middle of each side of the frame.

The extra clips are for use with the Game Frame Activity Kit (sold separately).

20. Adjust the “holes” in the web by sliding the knots in the cord as needed.

21. Apply the Game Frame decals as you wish on any of the poles. You may want to

apply the decals in a location that will help you identify certain pieces for faster

set-up the next time. We recommend that the decals be applied in the middle of

the top and bottom CROSSBARS.

22. Have fun!

SAFETY WARNING:

Bungee cord is elastic in nature and when pulled tightly and

released will SNAP back. When attaching bungee to the

frame, hold firmly and do not release grip until ring is

properly attached to clip.

Game Frame Assembly Instructions # 71327

Diagram A

Photo A

Project Adventure’s Game Frame and Web #74020

BASE BASE

LEGS (2) LEGS (2)

CROSSBARS (3)

CROSSBARS (3)

WEB