This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
ボールバルブ ヘラクレスシリーズ カタログ
〒274-0812 千葉県船橋市三咲7-22-7 FAX:047-449-2926ITS JAPAN
Valvola a sfera in acciaio carbonio per alta pressione - alta ciclicitàHigh pressure carbon steel ball valve - high ciclicity
HERCULES
Caratteristiche generali:
Estremità filettate EN ISO 228 o NPTTemperatura di utilizzo: da -20°C a +100°C con Oring in NBR da -20°C a +160°C con Oring in FKM (a richiesta)Pressione di utilizzo: PN500/7000 psi DN6, DN8, DN10, DN15 PN400/6000 psi DN20 e DN25 PN320/4500 psi DN32, DN40, DN50Fluido intercettato: fluidi liquidi e gassosi, di qualsiasi genere purchè compatibili con i materiali costitutivi.Antistatic deviceFire safe design
General featuresEnds: Threaded ends EN ISO 228 o NPTWorking temperature:-from -20°C to +100° with NBR Oring from -20°C to +160°C with FKM Oring (on request)Working pressure: DN6, DN8, DN10, DN15 PN500/7000 psi DN20 e DN25 PN400/6000 psi DN32, DN40, DN50 PN320/4500 psiFluid range: Different fluids, liquid and gaseous, compatible with the constituent materialsAntistatic deviceFire safe design
Esecuzioni speciali a richiesta:Per altre applicazioni consultare il nostro ufficio tecnico
Special execution on requestFor other applications, please contact our technical department
Certificazioni:Versione ATEX in conformità alla direttiva 94/9/ECCertificato ATEX a richiestaLivello di sicurezza funzionale SIL 3 in accordo a IEC 61508Versione PED CE1115 per misure ≥DN32
Approvals:ATEX version in conformity with directive 94/9/ECATEX certificate on requestSafety integrity level up SIL3 according to the IEC 61508PED CE1115 version for size ≥DN32
Il valore Kv è il valore di portata in m3/h (con acqua a 15°C) che provoca la caduta di pressione di 1 bar Kv is the coefficient, expressed in m3/h (with water at 15°C) causing a pressure loss of 1 bar.
diagramma pressione/temperatura
pressure/temperature diagram
DN6, DN8, DN10, DN15 PN500/7000 psiDN20 e DN25 PN400/6000 psi
DN32, DN40, DN50 PN320/4500 psi
5
3
4
6
8 7 9 2
1 9 78
10
11
12
1314
MATERIALI MATERIALS1 Corpo Body ≤DN25: 1.0737 (11SMnPb37); ≥DN32: 1.0577 (S355J2) Zincato - Zinc coated2 Sfera Ball A217 CA15 + Hard chromium plated3* O-ring NBR (FKM on request)4* Bussola inferiore Lower bush POWERAMMIDE blend di tecnopolimeri e di cariche aramidiche - Blend of polymers and aramid filler5* Bussola superiore Upper bush POWERAMMIDE blend di tecnopolimeri e di cariche aramidiche - Blend of polymers and aramid filler6 Stelo Stem A564 Tp 630 (17-4 PH)7* O-ring NBR (FKM on request)8 Manicotto Ends ≤DN25: 1.0737 (11SMnPb37); ≥DN32: 1.0577 (S355J2) Zincato - Zinc coated9* Seggio Seats EXTREME poliammide aromatica a catena lunga - Aromatic polyamide long chemical structure10 Molla antistatic device Antistatic device spring 1.4310 - X12CrNi17-711 Molla antistatic device superiore Upper antistatic device spring 1.4310 - X12CrNi17-7
12** Fermo Holder screw X5CrNiMo1713 - AISI31613** Leva Lever EN AB 46100 - AL SI 11 CU (FE) Verniciata - Painted14** Vite Screw A2 - 70
* Componenti kit di guarnizioni Seals kit components** Componenti dei kit leva Lever kit components
219
Her
cule
sCa
rbon
ste
elHercules
Carbon steel
DIMENSIONI DIMENSIONSSize A B C D E F G ØH Ch.Q M N P R S
A =Versione standard con O-ring in NBR. - Con O-ring in FKM a richiesta, lettera VA = Standard line with NBR O-ring. – with FKM O-ring on request, letter V
A = Standard line with NBR O-ring. – with FKM O-ring on request, letter V
VALVOLA PER ALTA CICLICITA' CON ATTUATORE DOPPIO E SEMPLICE EFFETTO HIGH CICLICITY VALVE WITH DOUBLE ACTING AND SPRING RETURN ACTUATOR
Il dimensionamento degli attuatori pneumatici è stato fatto considerando una pressione minima di alimentazione pari a 5,6 barg.The sizing of pneumatic actuators has been done considering a minimum supply pressure of 5,6 barg.
Il dimensionamento degli attuatori pneumatici è stato fatto considerando una pressione minima di alimentazione pari a 5,6 barg.The sizing of pneumatic actuators has been done considering a minimum supply pressure of 5,6 barg.
Versione con Attuatore Elettrico A RICHIESTA (NOTA: gli attuatori elettrici Omal non sono disponibili in versione ATEX) Version with Electric Actuator ON REQUEST (PLEASE NOTE: the OMAL electric actuators are not available in ATEX execution)
VERS
ION
E EN
ISO
228
EN
ISO
228
VER
SIO
NVE
RSIO
NE
NPT
N
PT V
ERSI
ON
VERS
ION
E N
PT
NPT
VER
SIO
NVE
RSIO
NE
EN IS
O 2
28
EN IS
O 2
28 V
ERSI
ON
H
L
221
Her
cule
s St
ainl
ess
stee
l
Valvola a sfera in acciaio inox per alta pressione - alta ciclicitàHigh pressure stainless steel ball valve - high ciclicity
HERCULES
Caratteristiche generali:
Estremità filettate EN ISO 228 o NPTTemperatura di utilizzo: da -23°C a +100°C con Oring in NBR da -30°C a +160°C con Oring in FKM (a richiesta)Pressione di utilizzo: PN500/7000 psi DN6, DN8, DN10, DN15 PN400/6000 psi DN20 e DN25 PN320/4500 psi DN32, DN40, DN50Fluido intercettato: fluidi liquidi e gassosi, di qualsiasi genere purchè compatibili con i materiali costitutiviAntistatic deviceFire safe design
General featuresThreaded ends EN ISO 228 o NPTWorking temperature: from -23°C to +100°C with NBR Oring from -30°C to +160°C with FKM Oring (on request)Working pressure: DN6, DN8, DN10, DN15 PN500/7000 psi DN20 e DN25 PN400/6000 psi DN32, DN40, DN50 PN320/4500 psiFluid range: Different fluids, liquid and gaseous, compatible with the constituent materialsAntistatic deviceFire safe design
Esecuzioni speciali a richiesta:Per altre applicazioni consultare il nostro ufficio tecnico
Special execution on requestFor other applications, please contact our technical department
Certificazioni:Versione ATEX in conformità alla direttiva 94/9/ECCertificato ATEX a richiestaLivello di sicurezza funzionale SIL 3 in accordo a IEC 61508Versione PED CE1115 per misure ≥DN32
Approvals:ATEX version in conformity with directive 94/9/ECATEX certificate on requestSafety integrity level up SIL3 according to the IEC 61508PED CE1115 version for size ≥DN32
Il valore Kv è il valore di portata in m3/h (con acqua a 15°C) che provoca la caduta di pressione di 1 bar Kv is the coefficient, expressed in m3/h (with water at 15°C) causing a pressure loss of 1 bar.
diagramma pressione/temperatura
pressure/temperature diagram
DN6, DN8, DN10, DN15 PN500/7000 psiDN20 e DN25 PN400/6000 psi
DN32, DN40, DN50 PN320/4500 psi
5
3
4
6
8 7 9 2
1 9 78
10
11
12
1314
MATERIALI MATERIALS1 Corpo Body Inox 1.4401 / X5CrNiMo17-12-22 Sfera Ball A217 CA15 + Hard chromium plated3* O-ring NBR (FKM on request)4* Bussola inferiore Lower bush POWERAMMIDE blend di tecnopolimeri e di cariche aramidiche - Blend of polymers and aramid filler5* Bussola superiore Upper bush POWERAMMIDE blend di tecnopolimeri e di cariche aramidiche - Blend of polymers and aramid filler6 Stelo Stem A564 Tp 630 (17-4 PH)7* O-ring NBR (FKM on request)8 Manicotto Ends A182 F316 / A479 TP3169* Seggio Seats EXTREME poliammide aromatica a catena lunga - Aromatic polyamide long chemical structure10 Molla antistatic device Antistatic device spring 1.4310 - X12CrNi17-711 Molla antistatic device superiore Upper antistatic device spring 1.4310 - X12CrNi17-7
12** Fermo Holder screw X5CrNiMo1713 - AISI31613** Leva Lever EN AB 46100 - AL SI 11 CU (FE) Nichelata - Nichel coated14** Vite Screw A2 - 70
* Componenti kit di guarnizioni Seals kit components** Componenti del kit leva Lever kit components
223
Her
cule
s St
ainl
ess
stee
l
Hercules
Stainless steel
DIMENSIONI DIMENSIONSSize A B C D E F G ØH Ch.Q M N P R S
A =Versione standard con O-ring in NBR. - Con O-ring in FKM a richiesta, lettera VA = Standard line with NBR O-ring. – with FKM O-ring on request, letter V
A = Standard line with NBR O-ring. – with FKM O-ring on request, letter V
VALVOLA PER ALTA CICLICITA' CON ATTUATORE DOPPIO E SEMPLICE EFFETTO HIGH CICLICITY VALVE WITH DOUBLE ACTING AND SPRING RETURN ACTUATOR
Il dimensionamento degli attuatori pneumatici è stato fatto considerando una pressione minima di alimentazione pari a 5,6 barg.The sizing of pneumatic actuators has been done considering a minimum supply pressure of 5,6 barg.
Il dimensionamento degli attuatori pneumatici è stato fatto considerando una pressione minima di alimentazione pari a 5,6 barg.The sizing of pneumatic actuators has been done considering a minimum supply pressure of 5,6 barg.
VERS
ION
E EN
ISO
228
EN
ISO
228
VER
SIO
NVE
RSIO
NE
NPT
N
PT V
ERSI
ON
VERS
ION
E N
PT
NPT
VER
SIO
NVE
RSIO
NE
EN IS
O 2
28
EN IS
O 2
28 V
ERSI
ON
Versione con Attuatore Elettrico A RICHIESTA (NOTA: gli attuatori elettrici Omal non sono disponibili in versione ATEX) Version with Electric Actuator ON REQUEST (PLEASE NOTE: the OMAL electric actuators are not available in ATEX execution)
H
L
225
Her
cule
s St
ainl
ess
stee
l PT
FE-T
FM16
00 s
eals
HERCULES- VALVOLA PER ALTA CICLICITÀ CON GUARNIZIONI IN PTFE-TFM1600
HERCULES - VALVE FOR HIGH CICLICITY WITH PTFE-TFM1600
226
Hercules Stainless steel PTFE-TFM
1600 seals
FEATURES & BENEFITS
1Tenuta in "TFM1600"
Seat in "TFM1600"
PTFE di seconda generazione con performance più elevate nella combina-zione pressione/temperatura
2nd generation PTFE with higher performance in pressure and temperature diagram
2Supporto stelo in "TFM1600"
“TFM1600” stem bush
Elevato numero di azionamenti
High number of cycles
3O-ring in elastomero da 90 Shore A
Elastomer O-Ring with a hardness of 90 Shore A
Nessun deperimento dovuto ad azionamenti estremamente veloci
No deterioration with quick operations
4Stelo in 17-4 PH H900
Stem in 17-4 PH H900
Maggior resistenza meccanica di circa 5 volte rispetto ad un classico AISI316
Increased mechanical strenght about 5 times more compared to a standard AISI316
4Rullatura stelo
Shaft rolling
Minor usura delle guarnizioni grazie alla bassa rugosità (0,4 micron Ra ) dello stelo che facilita lo scorrimento
Less wear of the seals due to the low roughness (0,4 micron Ra) which facilitate the sliding of the shaft
5Antistatic device (continuità elettrica tra sfera, stelo e corpo)
Antistatic device (electrical continuity between ball, stem and body)
Si evitano cariche elettrostatiche che potrebbero essere causa d'innesco in ambienti infiammabili e/o esplosivi
Static electricity is avoided which can cause sparks and fire in an inflammable/explosive environment
Sicurezza garantita del contatto durante tutta la vita della valvola
Contact safety throughout the entire life of the valve
Certificato PED
PED Certificate
Piena conformità alle norme di sicurezza europee per i dispositivi in pressio-ne (per DN > di 25)
Full compliance with European safety standards for pressure equipment (for DN> 25)
Fire safe design
Fire safe design
Garantisce la tenuta della valvola anche in caso di incendio
Guarantees the tightness of the valve also in case of fire
Certificato ATEX
Atex Certificate
Ne consente l'installazione in presenza di ambiente potenzialmente esplo-sivo
Installation is possible in a potential explosive environment
227
Her
cule
s St
ainl
ess
stee
l PT
FE-T
FM16
00 s
eals
Valvola a sfera in acciaio inox - alta ciclicitàStainless steel ball valve - high ciclicity
HERCULES CON GUARNIZIONI IN PTFE-TFM1600 HERCULES WITH PTFE-TFM1600 SEATS
Caratteristiche generali:
Estremità filettate EN ISO 228 o NPTTemperatura di utilizzo: da -30°C a +155°C Pressione di utilizzo: 100bar/1500 psi DN6, DN8, DN10, DN15 63 bar/1000 psi DN20 e DN25 50bar/700 psi DN32 e DN40 40bar/600 psi DN50Fluido intercettato: fluidi liquidi e gassosi chiamicamente aggressivi se compatibili con i materiali costitutivi Antistatic deviceFire safe design
General featuresThreaded ends: EN ISO 228 o NPTWorking temperature: from -30°C to +155°C Working pressure: DN6, DN8, DN10, DN15 100bar/1500 psi DN20 e DN25 63 bar/1000 psi DN32 e DN40 50bar/700 psi DN50 40bar/600 psiIntercepted fluid: liquid and gaseous fluids chemically aggressive if they are compatible with the construction materials Antistatic deviceFire safe design
Esecuzioni speciali a richiesta:Per altre applicazioni consultare il nostro ufficio tecnico
Special execution on requestFor other applications, please contact our technical department
Certificazioni:Versione ATEX in conformità alla direttiva 94/9/ECCertificato ATEX a richiestaLivello di sicurezza funzionale SIL 3 in accordo a IEC 61508Versione PED CE1115 per misure ≥DN32
Approvals:ATEX version in conformity with directive 94/9/ECATEX certificate on requestSafety integrity level up SIL3 according to the IEC 61508PED CE1115 version for size ≥DN32
Il valore Kv è il valore di portata in m3/h (con acqua a 15°C) che provoca la caduta di pressione di 1 bar Kv is the coefficient, expressed in m3/h (with water at 15°C) causing a pressure loss of 1 bar.
diagramma pressione/temperatura
pressure/temperature diagram
DN6, DN8, DN10, DN15 PN100/1500psiDN20 e DN25 PN63/1000 psiDN32 e DN40 PN50/700 psi
DN50 PN40/600 psi
5
3
4
6
8 7 9 2
1 9 78
10
11
12
1314
MATERIALI MATERIALS1 Corpo Body Inox 1.4401 / X5CrNiMo17-12-22 Sfera Ball A351 CF8M3* O-ring FKM 4* Bussola inferiore Lower bush PTFE-TFM16005* Bussola superiore Upper bush PTFE-TFM16006 Stelo Stem A564 Tp 630 (17-4 PH)7* O-ring FKM8 Manicotto Ends A182 F316 / A479 TP3169* Seggio Seats PTFE-TFM160010 Molla antistatic device Antistatic device spring 1.4310 - X12CrNi17-711 Molla antistatic device superiore Upper antistatic device spring 1.4310 - X12CrNi17-7
12** Fermo Holder screw X5CrNiMo1713 - AISI31613** Leva Lever EN AB 46100 - AL SI 11 CU (FE) Nichelata - Nickel coated14** Vite Screw A2 - 70
* Componenti kit di guarnizione Seals kit components** Componenti del kit leva Kit lever components
229
Her
cule
s St
ainl
ess
stee
l PT
FE-T
FM16
00 s
eals
Hercules Stainless steel PTFE-TFM
1600 seals
DIMENSIONI DIMENSIONS
Size A B C D E F G ØH Ch.Q M N P R SDN 6 - 1/8" 69 1/8" 30 13 17 27 10 6 19 21x30 6 M5 103,5 56,1DN 8 - 1/4" 69 1/4" 30 13 17 27 10 6 19 21x30 6 M5 103,5 56,1
VALVOLA PER ALTA CICLICITA' CON ATTUATORE DOPPIO E SEMPLICE EFFETTO HIGH CICLICITY VALVE WITH DOUBLE ACTING AND SPRING RETURN ACTUATOR
Il dimensionamento degli attuatori pneumatici è stato fatto considerando una pressione minima di alimentazione pari a 5,6 barg.The sizing of pneumatic actuators has been done considering a minimum supply pressure of 5,6 barg.
Il dimensionamento degli attuatori pneumatici è stato fatto considerando una pressione minima di alimentazione pari a 5,6 barg.The sizing of pneumatic actuators has been done considering a minimum supply pressure of 5,6 barg.
VERS
ION
E EN
ISO
228
EN
ISO
228
VER
SIO
NVE
RSIO
NE
NPT
N
PT V
ERSI
ON
VERS
ION
E N
PT
NPT
VER
SIO
NVE
RSIO
NE
EN IS
O 2
28
EN IS
O 2
28 V
ERSI
ON
Versione con Attuatore Elettrico A RICHIESTA (NOTA: gli attuatori elettrici Omal non sono disponibili in versione ATEX) Version with Electric Actuator ON REQUEST (PLEASE NOTE: the OMAL electric actuators are not available in ATEX execution)
H
L
231
Her
cule
s m
anua
l op
erat
edCa
rbon
ste
el
HERCULES MANUALE HERCULES MANUAL OPERATED
232
Hercules m
anual operated
Carbon steel
FEATURES & BENEFITS
1Tenuta in "MASTERAMMIDE"*
Seat in "MASTERAMMIDE"*
Minor usura rispetto a tenute non modificate
Less wear comparing with not modify seat
Elevata resistenza alla sollecitazione
High resistance to stress
2Sfera in acciaio inossidabile con rivestimento in Cromo Duro da 40µm
Stainless steel ball, coated with 40µm Hard Chrome
Maggior tenuta nel tempo grazie alla bassa usura della sfera
Longer seal life due to the low wear of the ball
3Supporto stelo in "MASTERAMMIDE"*
"MASTERAMMIDE"* stem bush
Si ha un perfetto allineamento dell'albero sul corpo e si evitano oscillazioni con alte pressioni
It grants a perfect alignment of the shaft on the body and prevents oscillations with high pressure
Nessuna possibilità di grippaggio
No seizing
4O-ring in elastomero con durezza di 90 Shore A
Elastomer O-Ring with a hardness of 90 Shore A
Nessun deperimento dovuto ad azionamenti estremamente veloci
No deterioration with quick operations
4O-ring a bassa permeabilità “Rapid Gas Decompression”
Low-permeability O-ring "Rapid Gas Decompression"
Buona resistenza alla decompressione esplosiva
Good resistance to explosive decompression
5Stelo in 17-4 PH H900
Stem in 17-4 PH H900
Maggior resistenza meccanica di circa 5 volte rispetto ad un classico AISI316
Increased mechanical strenght about 5 times more compared to a standard AISI316
5Rullatura stelo
Shaft rolling
Minor usura delle guarnizioni grazie alla bassa rugosità (0,4 micron Ra) dello stelo che facilita lo scorrimento
Less wear of the seals due to the low roughness (0,4 micron Ra) which facilitate the sliding of the shaft
Certificato PED
PED Certificate
Piena conformità alle norme di sicurezza europee per i dispositivi in pressio-ne (per DN > di 25)
Full compliance with European safety standards for pressure equipment (for DN> 25)
*Blend di tecnopolimeri e di cariche aramidiche*Blend of polymers and aramid filler
233
Her
cule
s m
anua
l op
erat
edCa
rbon
ste
el
Valvola a sfera in acciaio carbonio per alta pressioneHigh pressure carbon steel ball valve
HERCULES MANUALE HERCULES MANUAL OPERATED
Caratteristiche generali:
Estremità filettate EN ISO 228 o NPTTemperatura di utilizzo: -20°C +100°C con Oring in NBR -20°C +130°C con Oring in FKM (a richiesta)Pressione di utilizzo: PN500/7000 psi DN6, DN8, DN10, DN15 PN400/6000 psi DN20 e DN25 PN320/4500 psi DN32, DN40, DN50Fluido intercettato: fluidi liquidi e gassosi, di qualsiasi genere purchè compatibili con i materiali costitutivi.
General featuresThreaded ends EN ISO 228 or NPTWorking temperature: -20°C +100°C with NBR Oring -20°C +130°C with FKM Oring (on request)Working pressure: DN6, DN8, DN10, DN15 PN500/7000 psi DN20 e DN25 PN400/6000 psi DN32, DN40, DN50 PN320/4500 psiFluid range: Different fluids, liquid and gaseous, compatible with the constituent materials
Esecuzioni speciali a richiesta:Per altre applicazioni consultare il nostro ufficio tecnico
Special execution on requestFor other applications, please contact our technical department
CertificazioniVersione PED CE1115 per misure ≥DN32
ApprovalsPED CE1115 version for size ≥DN32
234
Her
cule
s m
anua
l op
erat
edCa
rbon
ste
el
Hercules m
anual operated
Carbon steel
Body Carbon Steel Masterammide + NBR Masterammide + FKM (on request)
DN6, DN8, DN10, DN15 PN500/7000 psiDN20 e DN25 PN400/6000 psi
DN32, DN40, DN50 PN320/4500 psi
MATERIALI MATERIALS1 Corpo Body ≤DN25: 1.0737 (11SMnPb37); ≥DN32: 1.0577 (S355J2) Zincato Galvanized2 Sfera Ball A217 CA15 + Hard chromium plated3 O-ring NBR (FKM on request)4 Bussola inferiore Lower bush MASTERAMMIDE blend di tecnopolimeri e di cariche aramidiche - Blend of polymers and aramid filler5 Bussola superiore Upper bush MASTERAMMIDE blend di tecnopolimeri e di cariche aramidiche - Blend of polymers and aramid filler6 Stelo Stem A564 Tp 630 (17-4 PH)7 O-ring NBR (FKM on request)8 Manicotto Ends ≤DN25: 1.0737 (11SMnPb37); ≥DN32: 1.0577 (S355J2)9 Seggio Seats MASTERAMMIDE blend di tecnopolimeri e di cariche aramidiche - Blend of polymers and aramid filler
10* Fermo Holder screw X5CrNiMo1713 - AISI31611* Leva Lever EN AB 46100 - AL SI 11 CU (FE) Verniciata Painted12* Vite Screw A2 - 70* Componenti del kit leva Kit lever components
PORTATA FLOW RATE KV m3/h
PN Size DN 61/8"
DN81/4"
DN 10 3/8"
DN 15 1/2"
DN 20 3/4"
DN 251"
DN 321"1/4
DN 401"1/2
DN 502"
KV m3/h 5,2 11 20 60 100 130 170 280Il valore Kv è il valore di portata in m3/h (con acqua a 15°C) che provoca la caduta di pressione di 1 bar Kv is the coefficient, expressed in m3/h (with water at 15°C) causing a pressure loss of 1 bar.
peso weight Kg. 0,35 0,34 0,82 1,16 1,57 2,41 3,55 5,39 10,15A =Versione standard con O-ring in NBR. - Con O-ring in FKM a richiesta, lettera VA = Standard line with NBR O-ring. – with FKM O-ring on request, letter V