Flexi Bsc Doc

Control the start-up of the other computer units either at MMI system or at Recovery ServiceTerminal extension (RCBUGG).

ZLE:U,RCBUGGGXZUSIC:COMP

Verification of SW VersionsPrint out all SW packages installed in the disksZWQO;Perform verification for each existing packageZWQB:STAT=BU:FORM=FAILED;

Make fallback of the running package

ZWKS:MODE=FULL,NAME=FBYYMMDD,DIRE=FBYYMMDD;

Check that the fallback copying was successful:ZWKP:FULL:PHASES;

Inspection of I/O SystemDisplay all the I/O devices The disk drives should enter the state WO-BU and remain in it. The VDU and LPT units will be inZISI; WO-ID or BL-SY state,

Change the state of the disk units to BL-USZISC::WDU,1:BL-US;ZISC::WDU,1:WO-ID;ZISC::WDU,1:WO-BU;Format the MO disk.ZIWKCheck that the formatting was successfulZIWX::Copy the Fallback to MO Disc

Testing Processor Units

Testing Message Bus Connections GO TO THE SHEET EMB test

Inspection of Maintenance System

Testing Wired Alarms

Back up to UMS ZIPS:,WDU-S,/ASF_1_25_0,,:,UMS-0,,,:NAME=ASF_1_25_0,DIR=INC,:DCM=NEW,:;

To verify that BSC does not have PCU plug-in units with same MAC HW addressZQRS:BCSU,<BCSU_ID>:<PCU_TYPE>,<PCU_ID>:INS,<INTERFACE>:SYM=NO;ZQRS:BCSU,3:PCUB,3:INS,IFETH0:SYM=NO;

The disk drives should enter the state WO-BU and remain in it. The VDU and LPT units will be inWO-ID or BL-SY state,

1

2

3

4

5

6

Testing Message Bus Connections

ZDDS;ZLP:1,EBS;Z1;

Send a test message using EMB-0.The printout is the configuration of the related BSC.

AT:0x007F,0

Message sent Received test messages using EMB-0 from following units:==================================================================================0000, 0004, 0005, 0030, 0031, 0032, 0033, 0034, 0035, 0036, 0037, 0038, 0039, 003A

Send a test message using EMB-1.The printout is the configuration of the related BSC.

AT:0x007F,1

Message sent Received test messages using EMB-1 from following units:==================================================================================0000, 0004, 0005, 0030, 0031, 0032, 0033, 0034, 0035, 0036, 0037, 0038, 0039, 003A

Check the MAC addresses of all computer units.The printout is the configuration of the related BSC.

A:0x000:0xFFFF

EMB-0 OK, EMB-1 OKUnit MAC addr 0 Mac addr 1 MB CID EMB0 EMB1 CPU SCD=======================================================================0000 02:00:00:80:00:20 02:00:00:80:00:30 0000 0000 OK OK CP816-A OK0004 02:00:00:80:01:20 02:00:00:80:01:30 0001 0001 OK OK CP816-A OK0005 02:00:00:80:02:20 02:00:00:80:02:30 0002 0002 OK OK CP816-A OK0030 02:00:00:80:03:20 02:00:00:80:03:30 0003 0003 OK OK CP816-A OKCheck that all computer units are listed and that there are two MAC addresses for each computer.

Exit EBSTER.Z;

Unload EBSTER.ZL:1;

BSC C-number

OSS C-numberET (1st X25)TSLET (redundent X25)TSL

CREATION OF OSS X.25 INTERFACE

CREATE PHYSICAL CHANNEL for PIU

ZQCC:0:OMU,0,1:335132,DTE,:512-1&&-8:;ZQCC:1:OMU,0,2:335132,DTE,:527-26&&-29:;

CHANGE STATE OF PHYSICAL CHANNEL

ZQSC:0,UNL;ZQSC:1,UNL;

INTERROGATE PHYSICAL CHANNEL STATE

ZQSI;

CREATE PHYSICAL CHANNEL GROUP

ZQGC:OMCPAD:0,0,50:;ZQGA:OMCPAD:1,0,45;

ZQGC:OMCCMISE:0,0,25:;ZQGA:OMCCMISE:1,0,20:;

Verifying the physical connection and physical channel group

ZQSI;ZQGI;

CREATE LOCAL/REMOTE NSAP

ZQBN:1:L:1:DTE=335132,SPI=03010100,:;ZQBN:2:L:1:DTE=335132,SPI=01000000,:;

ZQBN:5:L:4:NSEL=00,;

ZQBN:3:R:1:DTE=192851,SPI=01000000,CHG=OMCPAD,:;ZQBN:4:R:1:DTE=192851,SPI=03010100,CHG=OMCCMISE,:;

END is the IP address of com package ------ TNMSZQBN:6:R:5:AFI=39,IDI=356,DFI=00,ORG=000001,RES=00000001,AREA=0001,END=010151212045,NSEL=00:;

END is the IP address of Com Package ---- priority - 75 (OSSPKG in OSS)ZQBN:7:R:5:AFI=39,IDI=356,DFI=00,ORG=000001,RES=00000001,AREA=0001,END=010151212027,NSEL=00:;

//END is the IP address of Com Server --- priority - 50 (SCS SERVER on which OSSPKG runs)ZQBN:8:R:5:AFI=39,IDI=356,DFI=00,ORG=000001,RES=00000001,AREA=0001,END=010151212028,NSEL=00:;NOTE://If the system is 1+1 OR 2+0, then we have to give the IP address of the redundant COM server also. (DB server in OSS)

ZQBN:9:R:5:AFI=39,IDI=356,DFI=00,ORG=000001,RES=00000001,AREA=0001,END=010084193045,NSEL=00:;List all the NSAPsZQBL;

CREATE LOCAL/REMOTE NETWORK ADDRESSZQBC:LOCAL:L:;ZQBC:REMNMS:R:;ZQBC:LOCALCMI:L:;ZQBC:LOCALPAD:L:;ZQBC:REMCMI:R:;ZQBC:OMCPAD:R:; INTERROGATE NETWORK ADDRESS DATAZQBI;

ADD NSAP TO NETWORK ADDRESSZQBT:LOCALCMI:1:; ZQBT:LOCALPAD:2:; ZQBT:REMCMI:4,50:; ZQBT:OMCPAD:3,50:; ZQBT:LOCAL:5:; ZQBT:REMNMS:6,100:; ZQBT:REMNMS:7,50:; ZQBT:REMNMS:8,50:;

RELEASE NETWORK ADDRESS (All NSAPs)FOR USEZQBG:,UNL;

CREATE LOCAL/REMOTE OSI APPLICATIONLocal Applications

ZQDL:BSC335132PAD:::UNL:OMU:PAD:LOCALPAD:;

ZQDL:BSC335132A:::UNL:OMU:CMI,21F,0000:LOCAL:3333030230:3333030230:3333:;

ZQDL:BSC335132EHA:::UNL:OMU:CMI,2B1,0000:LOCAL:3333030231:3333030231:3333:;

ZQDL:BSC335132F:::UNL:OMU:VFS:LOCAL:1133030210:1133030210:1133:;

ZQDL:BSC335132VT:::UNL:OMU:VTP:LOCAL:2233030220:2233030220:2233:;

ZQDL:BSC335132NOD:::UNL:OMU:TPU,2AF,0:LOCAL:7733030270:7733030270:7733;

Remote Applications

ZQDR:OMC000000PAD:::UNL:PAD:OMCPAD:; ZQDR:OMC000000D1:::UNL:CMI:REMNMS:3333010130:3333010130:3333:; ZQDR:OMC000000BP:::UNL:CMI:REMNMS:3333010131:3333010131:3333;ZQDR:OMC000000FO:::UNL:VFS:REMCMI:0201:0201:0201:; ZQDR:OMC000000FP:::UNL:VFS:REMNMS:1133010210:1133010210:1133:; ZQDR:OMC000000SW:::UNL:VFS:REMNMS:1133010110:1133010110:1133:;

CHANGE OSI APPLICATION STATEZQDG:BSC335132A,LOC;ZQDG:BSC335132A,UNL;ZQDG:BSC335132A,LOC;

ADD SERVICE PROFILE TO OSI APPLICATION

ZQDA:BSC335132A:MOS=Y,FLT=Y,MR=Y,ES=N,CG=Y,:VER_1_AND_2:;

RELEASE OSI ADDRESS FOR USE (Change OSI application state)

ZQDG:BSC335132A,UNL;

CREATE - INTERROGATE AND UNLOCK X.25 LINKAGE

ZQLC:0:ES:OMU:1:SNPA=192851;ZQLC:1:ES:OMU:2:SNPA=192851;

ZQLI;ZQLG:0:X25:UNL:;ZQLG:1:X25:UNL:;ZQLI;

CREATE AND UNLOCK ES CLNS OBJECT

ZQEC:ES:ES:OMU:9:000000335132:1:39356F00000001000000010001:;ZQEG:ES:UNL:;ZQET:ES::;ZQEI;

CHECKING ALL

ZQNI;ZQCI;ZQSI;ZQGI;ZQLI;ZQLP:::;ZQEI;

ZQBL;ZQBI;ZQBI::MAX;ZQDI;ZQDI::MAX;ZQDI::PAR;

CREATE PROFILE check the password......

ZIAA:NUPADM:ALL=251:PARAPW=YES,VTIME=FOREVER,ACCESS=COM,UNIQUE=NO:TLIMIT=15:;ZIAH:NUPADM:NUPADM:;ZIOA:NUPADM:APPL=CM-X&PM-X&FM-X&RM-X:;

335132

192851512

1 8527

26 29

For redundant x.25

For redundant x.25

For redundant x.25

For redundant x.25

For redundant x.25

For redundant x.25

(It will prompt for the password give “PASSWORD”)

10.104.208.45

Terminal state should be WO-EX and Channel stste should be UNL-ENL. When data is transferred through the physical channel its state will change to UNL-ACT

Local NSAPs

Remote NSAPs

10.151.212.4527,28

9,370,455,367

(It will prompt for the password give “PASSWORD”)

BSC NAME BSC15JPRBSC LOCATION JEYPURDATE,TIME (YYYY-MM-DD,HH-MM-SS) 2009-09-04,14-20-00

ZQNM:0:NAME=BSC15JPR,LOC=JEYPUR:;

ZDCS:2009-09-04,14-20-00:ST=OFF:;

ZDCE:PLUS:05-30:;Y

ZUSS:SYM:C=DSK:;Y

BTS sw ACTIVATION

ZEWC:METRO:MF=BTS_C800,EXT=707,SDIR=PACK_3,;

ZEWC:FLEXI:MF=BTS_3030,EXT=014,SDIR=PACK_2:;

ZEWL;

AFTER COPYING Ultra BCF PACK INTO PACK_0

AFTER COPYING Flexi BCF PACK INTO PACK_1

PRFILE IMPLIMENTAION

Copy the PRFILES to the CONVPR Directory using FTT

ZIWY:S:SYSTEM=,UNIT=OMU,PATH=LFILES,DRIVE=WDU-S;ZIWY:D:SYSTEM=,UNIT=OMU,PATH=CONVPR,DRIVE=WDU-S:;ZIBC:,,MEFEE2SX,IMG;YZIBC:,,DXPFILGX,IMG;YZIBC:,,PRBFILSX,IMG;YZIWY:S:SYSTEM=,UNIT=OMU,PATH=BLCODE,DRIVE=WDU-S;ZIWY:D:SYSTEM=,UNIT=OMU,PATH=CONVPR,DRIVE=WDU-S;ZIBC:,,MAFILEGX,IMG;YZIWY:S:SYSTEM=,UNIT=OMU,PATH=BLCODE,DRIVE=WDU-S:;ZIWY:D:SYSTEM=,UNIT=OMU,PATH=LFILES,DRIVE=WDU-S,;ZIBC:,,MAFILEGX,IMG;YZDEY:S::OMU:LFILES:WDU-S;ZDEY:D::OMU:CONVPR:WDU-S;

ZDEE::CONVPR:PRFCNVGX,IMG;ZDEE::CONVPR:FIFCNVGX,IMG;

ZIWY:S:SYSTEM=,UNIT=OMU,PATH=CONVPR,DRIVE=WDU-S:;ZIWY:D:SYSTEM=,UNIT=OMU,PATH=LFILES,DRIVE=WDU-SB:;ZIBC:,,FIFILEGX,IMG;YZIBC:,,PRFILEGX,IMG;YZIBC:,,CID%,TXT;YZIBT:WDU,S,CID%,TXT,,,,A;YZDFM:OMU:NAME=PRFILEGX;ZDFM:OMU:NAME=FIFILEGX;ZDFM:MCMU,0:NAME=PRFILEGX;ZDFM:MCMU,0:NAME=FIFILEGX;ZDFM:MCMU,1:NAME=PRFILEGX; ZDFM:MCMU,1:NAME=FIFILEGX;ZDFM:BCSU,0:NAME=PRFILEGX;ZDFM:BCSU,0:NAME=FIFILEGX;ZDFM:BCSU,1:NAME=PRFILEGX;ZDFM:BCSU,1:NAME=FIFILEGX;ZDFM:BCSU,2:NAME=PRFILEGX;ZDFM:BCSU,2:NAME=FIFILEGX;

ZDFM:BCSU,3:NAME=PRFILEGX;ZDFM:BCSU,3:NAME=FIFILEGX;

TCSM CREATIONE.T. NO. 368CIRCUIT POOL 28BCSU NO. 1BCSU NO. 1BCSU NO. 1BCSU NO. 1CCSPCMNO. 0CCSPCMNO. 1CCSPCMNO. 2CCSPCMNO. 3CGR 1SIGNALING REQUIRED YLINK NO 1No. of TSLs 4BSC ID BSHSRSIGNALLING TSL No. 28SWITCH SIDE DATAMSS/MGW MSS02MSS/MSC SPC D'10656

ZWGC:368,1:POOL=28:BCSU,1:;YZWGC:368,2:POOL=28:BCSU,1:;ZWGC:368,3:POOL=28:BCSU,1:;ZWGS:368:4:;YZWGC:368,4:POOL=28:BCSU,1:;

ZRCA:CGR=1:ETPCM=368,CRCT=1-1&&-31,:CCSPCM=0:;ZRCA:CGR=1:ETPCM=368,CRCT=2-1&&-31,:CCSPCM=1:;ZRCA:CGR=1:ETPCM=368,CRCT=3-1&&-31,:CCSPCM=2:;ZRCA:CGR=1:ETPCM=368,CRCT=4-1&&-11,:CCSPCM=3:;

ZCEC:ETPCM=368,CRCT=1-1&&-31:BL:;ZCEC:ETPCM=368,CRCT=2-1&&-31:BL:;ZCEC:ETPCM=368,CRCT=3-1&&-31:BL:;ZCEC:ETPCM=368,CRCT=4-1&&-11:BL:;

ZCEC:ETPCM=368,CRCT=1-1&&-31:WO:;ZCEC:ETPCM=368,CRCT=2-1&&-31:WO:;ZCEC:ETPCM=368,CRCT=3-1&&-31:WO:;ZCEC:ETPCM=368,CRCT=4-1&&-11:WO:;

Signalling Link CreationZNCC:1:368-28,64,4,:BCSU,1:0:;ZNSA:NA1,D'10656,MSS02:1,1;ZNLA:1;ZNLC:1,ACT;

CREATION OF A INTERFACE

BSC NAMEBSC SPCMSC/MSS NAMEMSC SPCBSC C-numberET TSLNUMBER OF TSLBCSU IN WO-EX

CREATION OF MTP - CREATE THE NEEDED SIGNALLING LINKS

ZNCC:0:368-28,64,4,:BCSU,1:0:;

CREATING OWN SIGNALLING POINT

ZNRP:NA1,D'1059,BSPNP,SEP::1;

CREATING SIGNALLING LINK SET

ZNSC:NA1,D'9642,MSS02:0,0::::;

ADDING SIGNALLING LINK TO LINK SET

ZNSA:NA1,D'9642,MSS02:0,0;

CREATING SIGNALLING ROUTE SET

ZNRC:NA1,D'9642,MSS02,1,D,R:,,,0;

ACTIVATION OF SIGNALLING LINKS

ZNLA:0;

SWITCHOVER THE BCSU TO SP-EX TO MAKE SLC ACTIVATED

ACTIVATION OF SIGNALLING ROUTE

ZNVA:NA1,D'9642;

CHANGING SIGNALLING LINK STATE

ZNLC:0,ACT;

CHANGING SIGNALLING ROUTE STATE

ZNVC:NA1,D'9642::ACT;

CREATED SERVICE FOR USER PART

ZNPC:NA1,03,SCCP:Y:Y,208,10F;

DEFINING SCCP FOR SIGNALLING POINTZNFD:NA1,D'1059,1:FE,BSSAP,1:::::;ZNFD:NA1,D'9642,1:FE,BSSAP,1,:::::;

MODIFY BROADCAST STATUS OF SCCP SIGNALLING POINTS

ZOBM:NA1,D'1059,FE::Y;

MODIFY THE LOCAL BROADCAST STATUS OF SCCP SUBSYSTEMS(BSSAP)

ZOBC:NA1,D'9642,FE::Y;

CHANGE THE SCCP STATE (BSC)

ZNGC:NA1,D'1059:ACT;

CHANGE THE SCCP STATE (MSC)

ZNGC:NA1,D'9642:ACT;

CHANGE SUBSYSTEM(BSSAP) STATE (BSC)

ZNHC:NA1,D'1059:FE:ACT;

CHANGE SUBSYSTEM(BSSAP) STATE (MSC)

ZNHC:NA1,D'9642:FE:ACT;

CHECK SUBSYSTEM STATES

ZNHI:NA1;

CHECK SCCP STATES

ZNGI:NA1;

CHECK SIG ROUTE SETS, SIG LINK SETS AND SIG LINKS

ZNET;CGR CREATIONZRCC:TYPE=CCS,CGR=1,NCGR=MSS02CGR1:DIR=IN,NET=NA1,SPC=D'9642,LSI=AINA1;

ZRCC:TYPE=CCS,CGR=1,NCGR=MBHU1CG1:DIR=IN,NET=NA1,SPC=D'7025,LSI=AINA1:;ZRCC:TYPE=CCS,CGR=2,NCGR=MBHU3CG2:DIR=IN,NET=NA1,SPC=D'7025,LSI=AINA1:;

ZDDE:<computer unit>,<unit index>:"ZGSC"; <for all computer unts>ZABO;ZAHO;ZAHP:::<date,time>;ZNET;ZNSI:<network number>;ZNHI:<network number>;ZNEL;ZNPI;ZOBI:<network number>;ZOBL:<network number>;ZNRI:<network number>;ZNNI;ZNMI;ZNFI:<network number>;ZOCI;ZOCJ;ZUSI;ZWTI:P;

BSPNPD'1059MSS02D'9642

396391368

2841

BCF ID 45SECTOR-1 133SECTOR-2 134SECTOR-3 135ET 193BCSU 0PCSU 4SIZE 3RAC 121NSEI 14360MCC 405

LAC 2211

ZEFS:45:L;ZERS:BTS=133,TRX=1&2&3,:L;ZERS:BTS=134,TRX=4&5&6,:L;ZERS:BTS=135,TRX=9&10,:L;

ZEQS:BTS=133:L;ZEQS:BTS=134:L;ZEQS:BTS=135:L;

ZESE:ID=45,CRCT=193-25,SIZE=3,BCSU=0,PCU=4;

ZERM:BTS=133,TRX=01:PREF=P,GTRX=Y,DAP=45:;

ZERM:BTS=133,TRX=02:GTRX=Y,DAP=45:;ZERM:BTS=133,TRX=03:GTRX=Y,DAP=45:;

ZERM:BTS=134,TRX=05:PREF=P,GTRX=Y,DAP=45:;

ZERM:BTS=134,TRX=06:GTRX=Y,DAP=45:;ZERM:BTS=134,TRX=04:GTRX=Y,DAP=45:;

ZERM:BTS=135,TRX=09:PREF=P,GTRX=Y,DAP=45;

ZERM:BTS=135,TRX=10:GTRX=Y,DAP=45:;ZEQV:BTS=133:GENA=Y,EGENA=Y,RAC=121,CDED=10,CDEF=20,BFG=0,:NSEI=14360;ZEQV:BTS=134:GENA=Y,EGENA=Y,RAC=121,CDED=10,CDEF=20,BFG=0,:NSEI=14360;ZEQV:BTS=135:GENA=Y,EGENA=Y,RAC=121,CDED=10,CDEF=20,BFG=0,:NSEI=14360;

ZERS:BTS=133,TRX=1&2&3,:U;ZERS:BTS=134,TRX=4&5&6,:U;ZERS:BTS=135,TRX=9&10,:U;

ZEQS:BTS=133:U;ZEQS:BTS=134:U;ZEQS:BTS=135:U;

ZEFS:45:U;

4+4 HARDWARE LEVEL REDUNDANCYSLOT 1 2 3 4 5SW1 OFF OFF OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ONSW2 OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFFSW3 OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFFSW4 OFF OFF ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFFSW5 OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFFSW6 OFF OFF ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF



5 6 7 8ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFFOFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFFOFF OFF OFF OFF OFF ON OFF OFF OFF ON OFF OFF OFF ON OFFOFF OFF OFF OFF OFF ON OFF OFF OFF ON OFF OFF OFF ON OFFOFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFFOFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF

5 6 7 8ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFFOFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFFOFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF ON OFFOFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF ON OFFOFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFFOFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF

5 6 7 8ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFFOFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFFOFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFFOFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFFOFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFFOFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF

Download CD 0 & 1 into FTPTMP Dir

ZIWD:,OMU:WSB,NODEF:ASE_1_28_0,BLCODE:%,%,FF;ZIWD:,OMU:WSB,NODEF:ASE_1_28_0,LFILES:%,%,FF;ZIWD:,OMU:WSB,NODEF:ASE_1_28_0,MMDIRE:%,%,FF;

ZIWL:,:WSB,NODEF::FTPTMP,FF,02,AS:;

ZIWX::WS,NODEF:ASE_1_28_0,CDTEMP,:%,%:; ZIWD:,OMU:WSB,NODEF:ASE_1_28_0,CDTEMP:%,%;ZIWX::WS,NODEF:ASE_1_28_0,CDTEMP,:%,%:;

ZIWY:S:UNIT=OMU,PATH=/S14SWFDR/S14CD/S14CD0,DRIVE=WDU-S;ZIWY:D:UNIT=OMU,PATH=/FTPTMP,DRIVE=WDU-SB;ZIBC:,,SE0000MP,ZIP;

ZIWY:S:UNIT=OMU,PATH=/S14SWFDR/S14CD/S14CD1,DRIVE=WDU-S;ZIWY:D:UNIT=OMU,PATH=/FTPTMP,DRIVE=WDU-SB;ZIBC:,,SE0100MP,ZIP;

ZIXX:,,/FTPTMP,SE0000MP.ZIP:,:,,/FTPTMP:TIME=7200,PATHS=Y,:;ZIXX:,,/FTPTMP,SE0100MP.ZIP:,:,,/FTPTMP:TIME=7200,PATHS=Y,:;

ZIWY:S:UNIT=OMU,PATH=/FTPTMP/SE0000MP/M98,DRIVE=WDU-S;ZIWY:D:PATH=/ASE_1_28_0/CDTEMP,DRIVE=WDU-SB;ZIBC;

ZIWY:S:UNIT=OMU,PATH=/FTPTMP/SE0100MP/M98,DRIVE=WDU-S;ZIWY:D:PATH=/ASE_1_28_0/CDTEMP,DRIVE=WDU-SB;ZIBC;

ZDDE:OMU:"ZLP:M,MAS";ZDDE:OMU:"ZMXV:W0-/ASE_1_28_0/CDTEMP/";ZDDE:OMU:"ZMXV:W1-/ASE_1_28_0/CDTEMP/";

ZWNA:NAME=SEREL:1&2

ZIWY:S:PATH=/ASE_1_28_0/CDTEMP,DRIVE=WDU-S;ZIWY:D:PATH=/ASE_1_28_0/LFILES,DRIVE=WDU-SB;ZIBC:,,ESBB2DGX,BIN;

ZWQC:NAME=SE0100MP,DIRE=ASE_1_28_0:FORM=FAILED,CW=NEW;

ZWQO:CR;

ZWSS:NAME=SE0100MP;

Return to the Macro

For MCMU,0 in SP For MCMU,1 in SP

ZUSI:MCMU, ZUSI:MCMU,ZDPX:GSW,0:SW256B:CIDZDPX:GSW,1:SW256B:CID;

Change MCMU from SP to Change MCMU from SP to TE

ZWDG:GSW,0,SW256B; ZWDG:GSW,1,SW256B; { Update will take around 25 min }

ZDPX:GSW,0:SW256B:CIDZDPX:GSW,1:SW256B:CID;Change MCMU from TE to Change MCMU from TE to SP

SWITCH# config tSWITCH(config)# bridgeSWITCH(bridge)# vlan create 200SWITCH(bridge)# vlan add br200 1/1/1,1/1/23 taggedSWITCH(bridge)# vlan add br200 1/1/2-1/1/22,1/1/24 untaggedSWITCH(bridge)# vlan description br200 GB_200SWITCH(bridge)# vlan pvid 1/1/2-1/1/24 200SWITCH(bridge)# exit SWITCH(config)# exitSWITCH# write mem[OK]SWITCH# config tSWITCH(config)# interface br200SWITCH(config-if)# ldi% Ldi interface already existSWITCH(config-if)# no ldi% [br200] is not ldi interface SWITCH(config-if)# ip address 172.29.160.4/25SWITCH(config-if)# no shutdownSWITCH(config-if)# exitSWITCH(config)# exitSWITCH# write mem[OK]SWITCH# config tSWITCH(config)# bridgeSWITCH(bridge)# spanning-treeSWITCH(bridge)# spanning-tree mode mstSWITCH(bridge)# spanning-tree mst SWITCH(bridge)# spanning-tree mst 0 priority 4096SWITCH(bridge)# spanning-tree mst configuration SWITCH(bridge)# spanning-tree port 1/1/23 link-type point-to-pointSWITCH(bridge)# spanning-tree mst max-age 6SWITCH(bridge)# spanning-tree mode mst SWITCH(bridge)# spanning-tree mst configurationSWITCH(config-mst)# name region1 SWITCH(config-mst)# revision 0SWITCH(config-mst)# applySWITCH(config-mst)# exitSWITCH(bridge)# exitSWITCH(config)# exitSWITCH# write mem[OK]SWITCH# config tSWITCH(config)# service snmpSWITCH(config)# snmp community rw publicSWITCH(config)# snmp view nsn_view include 1.3.6.1SWITCH(config)# snmp trap2-host 10.1.4.1 publicSWITCH(config)# exitSWITCH# write mem[OK]SWITCH# config tSWITCH(config)# ip route 0.0.0.0/0 172.29.160.1SWITCH(config)# exitSWITCH# write mem

SWITCH# config tSWITCH(config)# bridgeSWITCH(bridge)# vlan create 200SWITCH(bridge)# vlan add br200 1/1/1,1/1/23 taggedSWITCH(bridge)# vlan add br200 1/1/2-1/1/22,1/1/24 untaggedSWITCH(bridge)# vlan description br200 GB_200SWITCH(bridge)# vlan pvid 1/1/2-1/1/24 200SWITCH(bridge)# exit SWITCH(config)# exitSWITCH# write mem

SWITCH# config tSWITCH(config)# interface br200SWITCH(config-if)# ldi% Ldi interface already existSWITCH(config-if)# no ldi% [br200] is not ldi interface SWITCH(config-if)# ip address 172.29.160.4/25SWITCH(config-if)# no shutdownSWITCH(config-if)# exitSWITCH(config)# exitSWITCH# write mem

SWITCH# config tSWITCH(config)# bridgeSWITCH(bridge)# spanning-treeSWITCH(bridge)# spanning-tree mode mstSWITCH(bridge)# spanning-tree mst SWITCH(bridge)# spanning-tree mst 0 priority 4096SWITCH(bridge)# spanning-tree mst configuration SWITCH(bridge)# spanning-tree port 1/1/23 link-type point-to-pointSWITCH(bridge)# spanning-tree mst max-age 6SWITCH(bridge)# spanning-tree mode mst SWITCH(bridge)# spanning-tree mst configurationSWITCH(config-mst)# name region1 SWITCH(config-mst)# revision 0SWITCH(config-mst)# applySWITCH(config-mst)# exitSWITCH(bridge)# exitSWITCH(config)# exitSWITCH# write mem

SWITCH# config tSWITCH(config)# service snmpSWITCH(config)# snmp community rw publicSWITCH(config)# snmp view nsn_view include 1.3.6.1SWITCH(config)# snmp trap2-host 10.1.4.1 publicSWITCH(config)# exitSWITCH# write mem

SWITCH# config tSWITCH(config)# ip route 0.0.0.0/0 172.29.160.1SWITCH(config)# exitSWITCH# write mem

config terminal bridge vlan create 150 vlan add br150 1/1/1,1/1/23 tagged vlan add br150 1/1/2-1/1/22,1/1/24 untagged vlan description br150 OSS_150 write mem sh vlan

config t interface br150 ldi no ldi ip address 10.104.201.138/29 no shutdown exit exit sh ip int brief

config t bridge spanning-tree spanning-tree mode mst spanning-tree mst spanning-tree mst 0 priority 32768 spanning-tree mst configuration name MST00 revision 0 apply exit write mem sh running-config

config t service snmp snmp community rw public snmp view nsn_view included 1.3.6.1 snmp trap2-host 10.1.4.1 public exit write mem

config tip route 0.0.0.0/0 10.104.201.142write memexit

name the vlan

/29 took appropriare nml

put the hsrp ip provided

name the vlan

/29 took appropriare nml

put the hsrp ip provided

Copy the SEREL,S14 PR FILE & NEW LICENCE into required folder

1.) Copy S14REL from S14SW to FTPTMP folder

ZIWY:S:UNIT=OMU,PATH=/S14SWFDR/S14SW,DRIVE=WDU-S;ZIWY:D:UNIT=OMU,PATH=/FTPTMP,DRIVE=WDU-SB;ZIBC;

ZIWY:S:UNIT=OMU,PATH=/S14SWFDR/S14PR,DRIVE=WDU-S;ZIWY:D:UNIT=OMU,PATH=/FTPTMP,DRIVE=WDU-SB;ZIBC;

ZIWY:S:UNIT=OMU,PATH=/S14SWFDR/S14LK,DRIVE=WDU-S;ZIWY:D:UNIT=OMU,PATH=/LICENCE,DRIVE=WDU-SB;ZIBC;

To take Fallback into FDU/UMS *Command will creat Dir then start Copy into F0*ZIWY:S:UNIT=OMU,PATH=/FB310111/,DRIVE=WDU-S;ZIWY:D:UNIT=OMU,PATH=/FB310111/,DRIVE=FDU-N0;ZIBC:,,,,,,,,,DIR::;

ZIWY:S:UNIT=OMU,PATH=/FB131212/,DRIVE=WDU-S; ZIWY:D:UNIT=OMU,PATH=/FB131212/,DRIVE=FDU-N0; ZIBC:,,,,,,,,,DIR::;

2.) Copy S14PRfiles file from S14PR to FTPTMP

3.) Copy S14LK’s file from S14LK to Licence

SW1 SW2 SW 3 SW4 SW5

Slot 1 OFF OFF OFF OFF OFFOFF OFF OFF OFF OFFOFF OFF OFF ON OFFOFF OFF OFF OFF OFF

SLOT 2 ON OFF OFF OFF OFFON OFF OFF OFF OFFOFF OFF OFF OFF OFFOFF OFF OFF OFF OFF






SLOT 8 ON OFF OFF OFF OFFON OFF OFF OFF OFFOFF OFF OFF OFF ONOFF OFF OFF OFF OFF

SW6This configuration is valid for 1 ETS2 card in each GTIC cartidge.

OFF GTIC 0 SLOT 1OFF GTIC 1 SLOT 1ONOFF

OFFOFFOFFOFF

OFFOFFOFFOFF

OFFOFFOFFOFF

OFFOFFOFFOFF

OFFOFFOFFOFF

OFFOFFOFFOFF

OFFOFFONOFF

SW1 SW2 SW 3 SW4 SW5

Slot 1 OFF OFF OFF OFF OFFOFF OFF OFF OFF OFFOFF OFF OFF ON OFFOFF OFF OFF OFF OFF






SLOT 7 ON OFF OFF OFF OFFON OFF OFF OFF OFFOFF OFF ON ON OFFOFF OFF OFF OFF OFF

SLOT 8 ON OFF OFF OFF OFFON OFF OFF OFF OFFOFF OFF OFF OFF ONOFF OFF OFF OFF OFF

SW6This configuration is valid for 1 ETS2 card in each GTIC cartidge.

OFF GTIC 0 SLOT 1 SLOT 2OFF GTIC 1 SLOT 1ONOFF

OFFOFFOFFOFF

OFFOFFOFFOFF

OFFOFFOFFOFF

OFFOFFOFFOFF

OFFOFFOFFOFF

OFFOFFOFFOFF

OFFOFFONOFF

BSCC_400 GTIC 0 1.0F 10.SB1-0GSW2KB 0BSCC_401 GTIC 0 1.0F 10.SB2-0GSW2KB 0BSCC_402 GTIC 0 1.0F 10.SB1-1GSW2KB 1BSCC_403 GTIC 0 1.0F 10.SB2-1GSW2KB 1BSCC_404 GTIC 0 1.0F 11.SB1-0GSW2KB 0BSCC_405 GTIC 0 1.0F 11.SB2-0GSW2KB 0BSCC_406 GTIC 0 1.0F 11.SB1-1GSW2KB 1BSCC_407 GTIC 0 1.0F 11.SB2-1GSW2KB 1BSCC_408 GTIC 0 1.0F 12.SB1-0GSW2KB 0BSCC_409 GTIC 0 1.0F 12.SB2-0GSW2KB 0BSCC_410 GTIC 0 1.0F 12.SB1-1GSW2KB 1BSCC_411 GTIC 0 1.0F 12.SB2-1GSW2KB 1BSCC_412 GTIC 0 1.0F 13.SB1-0GSW2KB 0BSCC_413 GTIC 0 1.0F 13.SB2-0GSW2KB 0BSCC_414 GTIC 0 1.0F 13.SB1-1GSW2KB 1BSCC_415 GTIC 0 1.0F 13.SB2-1GSW2KB 1BSCC_420 GTIC 1 2.0F 10.SB1-0GSW2KB 0BSCC_421 GTIC 1 2.0F 10.SB2-0GSW2KB 0BSCC_422 GTIC 1 2.0F 10.SB1-1GSW2KB 1BSCC_423 GTIC 1 2.0F 10.SB2-1GSW2KB 1BSCC_424 GTIC 1 2.0F 11.SB1-0GSW2KB 0BSCC_425 GTIC 1 2.0F 11.SB2-0GSW2KB 0BSCC_426 GTIC 1 2.0F 11.SB1-1GSW2KB 1BSCC_427 GTIC 1 2.0F 11.SB2-1GSW2KB 1BSCC_428 GTIC 1 2.0F 12.SB1-0GSW2KB 0BSCC_429 GTIC 1 2.0F 12.SB2-0GSW2KB 0BSCC_430 GTIC 1 2.0F 12.SB1-1GSW2KB 1BSCC_431 GTIC 1 2.0F 12.SB2-1GSW2KB 1BSCC_432 GTIC 1 2.0F 13.SB1-0GSW2KB 0BSCC_433 GTIC 1 2.0F 13.SB2-0GSW2KB 0BSCC_434 GTIC 1 2.0F 13.SB1-1GSW2KB 1BSCC_435 GTIC 1 2.0F 13.SB2-1GSW2KB 1

1.0F 01.SB2-0CSB005 Hotlink 5)1.0F 01.SB4-0CSB006 Hotlink 5)2.0F 01.SB2-0CSB009 Hotlink 5)2.0F 01.SB4-0CSB010 Hotlink 5)1.0F 07.SB1-0CSB005 Hotlink 5)1.0F 07.SB2-0CSB005 Hotlink 5)2.0F 07.SB1-0CSB011 Hotlink 5)2.0F 07.SB2-0CSB011 Hotlink 5)1.0F 08.SB1-0CSB005 Hotlink 5)1.0F 08.SB2-0CSB005 Hotlink 5)2.0F 08.SB1-0CSB011 Hotlink 5)2.0F 08.SB2-0CSB011 Hotlink 5)1.0F 06.SB1-0CSB005 Hotlink 5)1.0F 06.SB2-0CSB005 Hotlink 5)2.0F 06.SB1-0CSB011 Hotlink 5)2.0F 06.SB2-0CSB011 Hotlink 5)1.0F 01.SB2-1CSB012 Hotlink 5)1.0F 01.SB4-1CSB012 Hotlink 5)2.0F 01.SB2-1CSB006 Hotlink 5)2.0F 01.SB4-1CSB006 Hotlink 5)1.0F 07.SB1-1CSB010 Hotlink 5)1.0F 07.SB2-1CSB011 Hotlink 5)2.0F 07.SB1-1CSB006 Hotlink 5)2.0F 07.SB2-1CSB006 Hotlink 5)1.0F 08.SB1-1CSB011 Hotlink 5)1.0F 08.SB2-1CSB012 Hotlink 5)2.0F 08.SB1-1CSB006 Hotlink 5)2.0F 08.SB2-1CSB006 Hotlink 5)1.0F 06.SB1-1CSB011 Hotlink 5)1.0F 06.SB2-1CSB012 Hotlink 5)2.0F 06.SB1-1CSB007 Hotlink 5)2.0F 06.SB2-1CSB007 Hotlink 5)

EXTERNAL CREATION

ZWAA:4000:PW:"MAINS FAIL":;ZWAA:4001:PW:"AC FAIL":;ZWAA:4002:EX:"DG FAIL":;ZWAA:4003:EX:"BATTERY RUNNING":;ZWAA:4004:EX:"HIGH ROOM TEMPERATURE":;ZWAA:4005:EX:"LOW FUEL":;ZWAA:4006:EX:"SHELTER DOOR OPEN":;ZWAA:4007:EX:"RECTIFIER FAIL":;ZWAA:4008:EX:"FIRE ALARM":;ZWAA:4009:EX:"LOW VOLTAGE DC":;ZWAA:4010:EX:"DG ON LOAD":;ZWAA:4011:EX:"DOOR OPEN":;

ZWAT;

ZWAI:HWAT:OMU:0,4000,"RECT 1 FAIL":;ZWAI:HWAT:OMU:1,4001,"RECT 2 FAIL":;ZWAI:HWAT:OMU:2,4002,"MAINS FAIL":;ZWAI:HWAT:OMU:3,4003,"TEMP HIGH":;ZWAI:HWAT:OMU:4,4004,"SMOKE & FIRE":;ZWAI:HWAT:OMU:5,4005,"SITE ON DG":;ZWAI:HWAT:OMU:6,4006,"DG NOT START":;ZWAI:HWAT:OMU:7,4007,"DG FAIL TO STOP":;ZWAI:HWAT:OMU:8,4008,"DG LOW FUEL":;ZWAI:HWAT:OMU:9,4009,"AC 1 FAIL":;

ZWAI:HWAT:OMU:10,4010,"AC 2 FAIL":;

ZWAI:HWAT:OMU:11,4011,"DOOR OPEN":;

ZWAX:HWAT:OMU:0:POL=0;ZWAX:HWAT:OMU:1:POL=0;ZWAX:HWAT:OMU:2:POL=1;ZWAX:HWAT:OMU:3:POL=0;ZWAX:HWAT:OMU:4:POL=0;ZWAX:HWAT:OMU:5:POL=0;ZWAX:HWAT:OMU:6:POL=0;ZWAX:HWAT:OMU:7:POL=0;ZWAX:HWAT:OMU:8:POL=0;ZWAX:HWAT:OMU:9:POL=0;ZWAX:HWAT:OMU:10:POL=0;ZWAX:HWAT:OMU:11:POL=1;ZWAP:HWAT:OMU::;

ZWAI:HWAT:OMU:0,4000,"SITE ON BATTERY":;ZWAI:HWAT:OMU:1,4001,"DG RUNNING":;ZWAI:HWAT:OMU:2,4002,"SITE DOOR OPEN":;ZWAI:HWAT:OMU:3,4003,"AC FAULTY":;ZWAI:HWAT:OMU:4,4004,"DG FAIL TO START":;ZWAI:HWAT:OMU:5,4005,"FIRE DETECTION":;ZWAI:HWAT:OMU:6,4006,"LOW FUEL":;ZWAI:HWAT:OMU:7,4007,"RECTIFIER MODULE FAIL":;ZWAI:HWAT:OMU:8,4008,"DG FAIL TO STOP":;ZWAI:HWAT:OMU:9,4009,"ROOM TEMP HIGH":;

ZWAI:HWAT:OMU:10,4010,"LOW BATTERY":;

ZWAI:HWAT:OMU:0,4000,"SITE ON BATTERY":;ZWAI:HWAT:OMU:1,4001,"DG RUNNING":;ZWAI:HWAT:OMU:2,4002,"SITE DOOR OPEN":;ZWAI:HWAT:OMU:3,4003,"AC FAULTY":;ZWAI:HWAT:OMU:4,4004,"DG FAIL TO START":;ZWAI:HWAT:OMU:5,4005,"FIRE DETECTION":;ZWAI:HWAT:OMU:6,4006,"LOW FUEL":;ZWAI:HWAT:OMU:7,4007,"RECTIFIER MODULE FAULTY":;ZWAI:HWAT:OMU:8,4008,"DG FAIL TO STOP":;ZWAI:HWAT:OMU:9,4009,"ROOM TEMP HIGH":;ZWAI:HWAT:OMU:10,4010,"LOW BATTERY":;

ZWAA:4000:PW:"SITE ON BATTERY":;ZWAA:4001:PW:"DG RUNNING":;ZWAA:4002:EX:"SITE DOOR OPEN":;ZWAA:4003:EX:"AC FAULTY":;ZWAA:4004:EX:"DG FAIL TO STAR":;ZWAA:4005:EX:"FIRE DETECTION":;ZWAA:4006:EX:"LOW FUEL":;ZWAA:4007:EX:"RECTIFIER MODULE FAULTY":;ZWAA:4008:EX:"DG FAIL TO STOP":;ZWAA:4009:EX:"ROOM TEMP HIGH":;ZWAA:4010:EX:"LOW BATTERY":;ZWAA:4011:EX:"DOOR OPEN":;

Flexi Bsc Doc

Documents

user part

adding signalling

sig link sets

signalling

received test

room temp

signalling

signalling