Eval-FB2M5LRR Ethernet LC Evaluation Kit User Guide Eval-FB2M5LRR Revision A 1 OVERVIEW The Eval-FB2M5LRR evaluation kit enables evaluation of the Firecomms LC transceiver for plastic optic fibre (POF) and large core glass fibre (200, 400 um PCS). The kit includes a single LC transceiver pre-mounted onto a simple PCB that allows easy application of DC power via standard 2 mm diameter DC jacks. Data inputs (TD +/-) and data outputs (RD +/-) are connected via standard screw terminal SMA connectors. A single loop-back POF cable with LC plug is also included. For particular POF or PCS lengths and assemblies please contact Firecomms Applications support directly. 1 12 1 μ H IC IC 2 3 4 5 6 7 8 9 10 11 100 nF 1 μ H 100 nF 100 nF 100 nF 100 Ω 100 nF 100 nF RD + RD - RSSI Vcc Vcc TD + TD - 10 μ F 10 μ F 10 μ F 10 μ F 10 k Ω R L FIGURE 1 Recommended circuit layout for the LC transceiver
2
Embed
Eval-FB2M5LRR Ethernet LC Evaluation Kit User Guide · 2020-03-30 · Eval-FB2M5LRR Ethernet LC Evaluation Kit User Guide Eval-FB2M5LRR Revision A 2 EVALUATION KIT CONTENTS The Evaluation
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Eval-FB2M5LRR
Ethernet LC Evaluation Kit
User Guide
Eval-FB2M5LRR Revision A
1
OVERVIEW
The Eval-FB2M5LRR evaluation kit enables
evaluation of the Firecomms LC transceiver for
plastic optic fibre (POF) and large core glass
fibre (200, 400 um PCS). The kit includes a single
LC transceiver pre-mounted onto a simple PCB
that allows easy application of DC power via
standard 2 mm diameter DC jacks. Data inputs
(TD +/-) and data outputs (RD +/-) are connected
via standard screw terminal SMA connectors. A
single loop-back POF cable with LC plug is also
included.
For particular POF or PCS lengths and
assemblies please contact Firecomms
Applications support directly.
1
1 2
1 µ H
IC
IC
2
3
4
5
6
7
8
9
1 0
1 1
1 0 0 n F
1 µ H
1 0 0 n F
1 0 0 n F
1 0 0 n F
1 0 0 Ω
1 0 0 n F
1 0 0 n F
R D +
R D -
R S S I
V c c
V c c
T D +
T D -
1 0 µ F
1 0 µ F
1 0 µ F
1 0 µ F
1 0 k ΩR L
FIGURE 1
Recommended circuit layout for the LC transceiver
Eval-FB2M5LRR
Ethernet LC Evaluation Kit
User Guide
Eval-FB2M5LRR Revision A
2
EVALUATION KIT CONTENTS
The Evaluation Kit contains the following:
1. Evaluation PCB
2. FB2M5LRR mounted onto the evaluation PCB
3. POF cable with loop back LC plug (1 m, 0.5 NA, 2.2 mm jacket simplex POF)
4. FB2M5LRR Datasheet
INITIAL SETUP
1. Connect GND of a DC power supply to the ground points of the PCB (black terminals).
2. Connect 3.3 V to each of the Tx and Rx VCC jacks (red terminals).
3. To monitor RSSI, connect a multimeter or oscilloscope channel set to 1 MΩ input and measure the
voltage VRSSI. VRSSI is set by a 10 kΩ resistor. See datasheet for graph of optical power against VRSSI.
4. Connect suitable pattern generator differential data signals via SMA cables to the TD +/- data pins.
5. Connect the RD +/- data pins to a suitable high-speed oscilloscope using 50 Ω termination and high-
speed coax, SMA terminated cables.
6. For a loop-back cable test, connect the provided LC loop-back cable assembly into the LC
connector. This connects the Tx back to the Rx over 1m of Step-Index POF.