© 2014 Stanley Black & Decker, Inc. New Britain, CT 06053 U.S.A. 43668 2/2015 Ver. 6 USER MANUAL Safety, Operation and Maintenance EA08 Hydraulic Earth Auger
© 2014 Stanley Black & Decker, Inc.New Britain, CT 06053
U.S.A.43668 2/2015 Ver. 6
USER MANUAL Safety, Operation and Maintenance
EA08Hydraulic
Earth Auger
2 ► EA08 User Manual
DECLARATION OF CONFORMITYÜBEREINSTIMMUNGS-ERKLARUNGDECLARATION DE CONFORMITE CEE DECLARACION DE CONFORMIDADDICHIARAZIONE DI CONFORMITA
Hydraulic Tools
______________________________________________________________________I, the undersigned:Ich, der Unterzeichnende:Je soussigné:El abajo firmante:lo sottoscritto:
Weisbeck, Andy Surname and First names/Familiennname und Vornamen/Nom et prénom/Nombre y apellido/Cognome e nome
hereby declare that the equipment specified hereunder:bestätige hiermit, daß erklaren Produkt genannten Werk oder Gerät:déclare que l’équipement visé ci-dessous:Por la presente declaro que el equipo se especifica a continuación:Dichiaro che le apparecchiature specificate di seguito:
1. Category: Earth Auger, HydraulicKategorie:Catégorie:Categoria:Categoria:
2. Make/Marke/Marque/Marca/Marca Stanley3. Type/Typ/Type/Tipo/Tipo: EA08102A4. Serial number of equipment:
Seriennummer des Geräts:Numéro de série de l’équipement:Numero de serie del equipo:Matricola dell´attrezzatura:
All
Has been manufactured in conformity with Wurde hergestellt in Übereinstimmung mit Est fabriqué conformément Ha sido fabricado de acuerdo conE’ stata costruita in conformitá con
Directive/StandardsRichtlinie/StandardsDirectives/NormesDirectriz/Los NormasDirettiva/Norme
No.NrNuméroNon.
Approved bodyPrüfung durchOrganisme agrééAprobadoCollaudato
EN ISOEN ISOMachinery DirectiveEN ISO
20643:20053744:20102006/42/EC:200612100:2010
SelfSelfSelfSelf
5. Special Provisions: NoneSpezielle Bestimmungen: Dispositions particulières: Provisiones especiales: Disposizioni speciali:
6. Representative in the Union: Patrick Vervier, Stanley Dubuis 17-19, rue Jules Berthonneau-BP 3406 41034 Blois Cedex, France. Vertreter in der Union/Représentant dans l’union/Representante en la Union/Rappresentante presso l’Unione
Done at/Ort/Fait à/Dado en/Fatto a Stanley Hydraulic Tools, Milwaukie, Oregon USA Date/Datum/le/Fecha/Data 1-10-11
Signature/Unterschrift/Signature/Firma/Firma
Position/Position/Fonction/Cargo/Posizione Director of Product Development
DECLARATION OF CONFORMITY
EA08 User Manual ◄ 3
SERVICING: This manual contains safety, operation, and routine maintenance instructions. Stanley Hydraulic Tools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an au-thorized and certified dealer. Please read the following warning.
For the nearest authorized and certified dealer, call Stanley Hydraulic Tools at the number listed on the back of this manual and ask for a Customer Service Representative.
WARNING
SERIOUS INJURY OR DEATH COULD RESULT FROM THE IMPROPER REPAIR OR SERVICE OF THIS TOOL.
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER.
DECLARATION OF CONFORMITY ..........................................................................................................................2SAFETY SYMBOLS ..................................................................................................................................................4SAFETY PRECAUTIONS ..........................................................................................................................................5TOOL STICKERS & TAGS ........................................................................................................................................6HOSE TYPES ............................................................................................................................................................7HOSE RECOMMENDATIONS ..................................................................................................................................8
FIGURE 1. TYPICAL HOSE CONNECTIONS .......................................................................................................8HTMA REQUIREMENTS ...........................................................................................................................................9OPERATION ............................................................................................................................................................10
FIGURE 2. INSTALLING THE AUGER ................................................................................................................10FIGURE 3. INSTALLING TORQUE TUBE ...........................................................................................................10
TROUBLESHOOTING ............................................................................................................................................12SPECIFICATIONS ...................................................................................................................................................13ACCESSORIES.......................................................................................................................................................13EA08 PARTS ILLUSTRATION.................................................................................................................................14EA08 PARTS LIST...................................................................................................................................................15
TABLE OF CONTENTS
IMPORTANT
To fill out a Product Warranty Validation form, and for information on your warranty, visit Stanleyhydraulics.com and select the Company tab, Warranty.
(NOTE: The warranty Validation record must be submitted to validate the warranty).
4 ► EA08 User Manual
Always observe safety symbols. They are included for your safety and for the protection of the tool.
LOCAL SAFETY REGULATIONSEnter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte-nance personnel.
Safety symbols and signal words, as shown below, are used to emphasize all operator, maintenance and repair ac-tions which, if not strictly followed, could result in a life-threatening situation, bodily injury or damage to equipment.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
DANGERThis safety alert and signal word indicate an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNINGThis safety alert and signal word indicate a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTIONThis safety alert and signal word indicate a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTIONThis signal word indicates a potentially hazardous situation which, if not avoid-ed, may result in property damage.
NOTICEThis signal word indicates a situation which, if not avoided, will result in damage to the equipment.
IMPORTANTThis signal word indicates a situation which, if not avoided, may result in dam-age to the equipment.
SAFETY SYMBOLS
EA08 User Manual ◄ 5
Tool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose.These safety precautions are given for your safety. Re-view them carefully before operating the tool and before performing general maintenance or repairs.Supervising personnel should develop additional pre-cautions relating to the specific work area and local safety regulations. If so, place the added precautions in the space provided in this manual.The EA08 Hydraulic Earth Auger will provide safe and dependable service if operated in accordance with the instructions given in this manual. Read and understand this manual and any stickers and tags attached to the tool and hoses before operation. Failure to do so could result in personal injury or equipment damage.
• Operator must start in a work area without bystand-ers. The operator must be familiar with all prohibited work areas such as excessive slopes and danger-ous terrain conditions.
• Establish a training program for all operators to en-sure safe operation.
• Do not operate the tool unless thoroughly trained or under the supervision of an instructor.
• Always wear safety equipment such as goggles, head protection, and safety shoes at all times when operating the tool.
• Do not inspect or clean the tool while the hydraulic power source is connected. Accidental engagement of the tool can cause serious injury.
• Do not operate the earth auger without first installing the torque tube.
• Do not install or remove an auger while the hydraulic power source is connected. Accidental engagement of the tool can cause serious injury.
• Never operate the earth auger if you cannot be sure that underground utilities are not present. Under-ground electrical utilities present an electrocution hazard. Underground gas utilities present an explo-sion hazard. Other underground utilities may pres-ent other hazards.
• Do not wear loose fitting clothing when operating the
earth auger. Loose fitting clothing can get entangled with the earth auger and cause serious injury.
• Always operate the earth auger at full throttle. Op-erating the earth auger with the trigger slightly depressed raises the hydraulic pressure which in-creases torque output. This type of operation can result in unexpected “kickback”.
• Do not remove the earth auger from a hole until it has completely stopped turning.
• Supply hoses must have a minimum working pres-sure rating of 2500 psi/175 bar.
• Be sure all hose connections are tight.• The hydraulic circuit control valve must be in the
OFF position when coupling or uncoupling the tool. Wipe all couplers clean before connecting. Failure to do so may result in damage to the quick couplers and cause overheating of the hydraulic system. Use only lint-free cloths.
• Do not operate the tool at oil temperatures above 140 °F/60 °C. Operation at higher oil temperatures can cause operator discomfort and may damage the tool.
• Do not operate a damaged, improperly adjusted, or incompletely assembled tool.
• To avoid personal injury or equipment damage, all tool repair, maintenance and service must only be performed by authorized and properly trained per-sonnel.
• Do not exceed the rated limits of the tool or use the tool for applications beyond its design capacity.
• Always keep critical tool markings, such as labels and warning stickers legible.
• Always replace parts with replacement parts recom-mended by Stanley Hydraulic Tools.
• Check fastener tightness often and before each use daily.
SAFETY PRECAUTIONS
6 ► EA08 User Manual
SAFETY TAG P/N 15875 (Shown smaller then actual size)
D A N G E RD A N G E R
READ OPERATION MANUAL AND SAFETY INSTRUCTIONS FOR THIS
TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE OPERATION MANUAL.
TAG TO BE REMOVED ONLY BY TOOL OPERATOR.
SEE OTHER SIDE
1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CER-TIFIED AS NON-CONDUCTIVE WHEN USING HYDRAULIC TOOLS ON OR NEAR ELECTRICAL LINES MAY RESULT IN DEATH OR SERIOUS INJURY.BEFORE USING HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE ON OR NEAR ELECTRIC LINES BE SURE THE HOSE IS MAINTAINED AS NON-CONDUCTIVE. THE HOSE SHOULD BE REGULARLY TESTED FOR ELECTRIC CUR-RENT LEAKAGE IN ACCORDANCE WITH YOUR SAFETY DEPARTMENT INSTRUCTIONS.
2. A HYDRAULIC LEAK OR BURST MAY CAUSE OIL INJEC-TION INTO THE BODY OR CAUSE OTHER SEVERE PERSONAL INJURY.A. DO NOT EXCEED SPECIFIED FLOW AND PRESSURE
FOR THIS TOOL. EXCESS FLOW OR PRESSURE MAY CAUSE A LEAK OR BURST.
B. DO NOT EXCEED RATED WORKING PRESSURE OF HYDRAULIC HOSE USED WITH THIS TOOL. EXCESS PRESSURE MAY CAUSE A LEAK OR BURST.
C. CHECK TOOL HOSE COUPLERS AND CONNECTORS DAILY FOR LEAKS. DO NOT FEEL FOR LEAKS WITH YOUR HANDS. CONTACT WITH A LEAK MAY RESULT IN SEVERE PERSONAL INJURY.
I M P O R T A N T
D. DO NOT LIFT OR CARRY TOOL BY THE HOSES. DO NOT ABUSE HOSE. DO NOT USE KINKED, TORN OR DAMAGED HOSE.
3. MAKE SURE HYDRAULIC HOSES ARE PROPERLY CON-NECTED TO THE TOOL BEFORE PRESSURING SYSTEM. SYSTEM PRESSURE HOSE MUST ALWAYS BE CON-NECTED TO TOOL “IN” PORT. SYSTEM RETURN HOSE MUST ALWAYS BE CONNECTED TO TOOL “OUT” PORT. REVERSING CONNECTIONS MAY CAUSE REVERSE TOOL OPERATION WHICH CAN RESULT IN SEVERE PERSONAL INJURY.
4. DO NOT CONNECT OPEN-CENTER TOOLS TO CLOSED-CENTER HYDRAULIC SYSTEMS. THIS MAY RESULT IN LOSS OF OTHER HYDRAULIC FUNCTIONS POWERED BY THE SAME SYSTEM AND/OR SEVERE PERSONAL INJURY.
5. BYSTANDERS MAY BE INJURED IN YOUR WORK AREA. KEEP BYSTANDERS CLEAR OF YOUR WORK AREA.
6. WEAR HEARING, EYE, FOOT, HAND AND HEAD PRO-TECTION.
7. TO AVOID PERSONAL INJURY OR EQUIPMENT DAMAGE, ALL TOOL REPAIR MAINTENANCE AND SERVICE MUST ONLY BE PERFORMED BY AUTHORIZED AND PROPERLY TRAINED PERSONNEL.
I M P O R T A N T
READ OPERATION MANUAL AND SAFETY INSTRUCTIONS FOR THIS
TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE OPERATION MANUAL.
TAG TO BE REMOVED ONLY BY TOOL OPERATOR.
SEE OTHER SIDE
The safety tag (P/N 15875) at right is attached to the tool when shipped from the factory. Read and understand the safety instructions listed on this tag before removal. We suggest you retain this tag and attach it to the tool when not in use.
NOTE:THE INFORMATION LISTED ON THE STICKERS SHOWN,
MUST BE LEGIBLE AT ALL TIMES.
REPLACE DECALS IF THEY BECOME WORN OR
DAMAGED. REPLACEMENTS ARE AVAILABLE FROM YOUR LOCAL STANLEY
DISTRIBUTOR.
11207CIRCUIT D DECAL
28323CE DECAL
23139NAME TAG 11206
CIRCUIT C STICKER
CALL BEFORE YOU DIG
39423COMPOSITE DECAL
66409SOUND POWER DECAL
39424WARNING DECAL
WARNING
TOOL STICKERS & TAGS
EA08 User Manual ◄ 7
The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy-draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are:
Certified non-conductive — constructed of thermoplastic or synthetic rubber inner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. Hose labeled certified non-conductive is the only hose authorized for use near electrical conductors.Wire-braided (conductive) — constructed of synthetic rubber inner tube, single or double wire braid reinforce-ment, and weather resistant synthetic rubber cover. This hose is conductive and must never be used near electrical conductors.Fabric-braided (not certified or labeled non-conductive) — constructed of thermoplastic or synthetic rubber in-ner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. This hose is not certified non-conductive and must never be used near electrical conductors.
HOSE SAFETY TAGSTo help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS.If the information on a tag is illegible because of wear or damage, replace the tag immediately. A new tag may be obtained from your Stanley Distributor.
THE TAG SHOWN BELOW IS ATTACHED TO “CERTIFIED NON-CONDUCTIVE” HOSE
THE TAG SHOWN BELOW IS ATTACHED TO “CONDUCTIVE” HOSE.(Shown smaller than actual size)
SIDE 1
D A N G E R1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE
WHEN USING HYDRAULIC TOOLS ON OR NEAR ELECTRIC LINES MAY RESULT IN DEATH OR SERIOUS INJURY.FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROP-ERLY TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND ELECTRIC LINES.
2. BEFORE USING HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE ON OR NEAR ELECTRIC LINES. WIPE THE ENTIRE LENGTH OF THE HOSE AND FIT-TING WITH A CLEAN DRY ABSORBENT CLOTH TO REMOVE DIRT AND MOISTURE AND TEST HOSE FOR MAXIMUM ALLOWABLE CURRENT LEAKAGE IN ACCORDANCE WITH SAFETY DEPARTMENT INSTRUCTIONS.
SEE OTHER SIDE
SIDE 2
DO
NO
T R
EM
OV
E T
HIS
TA
G
3. DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE. KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT CONTACT DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION AND SEVERE PERSONAL INJURY.
4. HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, ABRASION, CUTTING, OR CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.
5. CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAM-AGE TO COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE IMMEDIATELY. NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.
6. AFTER EACH USE STORE IN A CLEAN DRY AREA.
SEE OTHER SIDE
D A N G E R
DO
NO
T R
EM
OV
E T
HIS
TA
G D A N G E R
(Shown smaller than actual size)SIDE 2
5. CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAMAGE TO COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE IMMEDIATELY. NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.
6. AFTER EACH USE STORE IN A CLEAN DRY AREA.
D A N G E R DO
NO
T R
EM
OV
E T
HIS
TA
G
D A N G E R
SIDE 1
1. DO NOT USE THIS HYDRAULIC HOSE ON OR NEAR ELECTRIC LINES. THIS HOSE IS NOT LABELED OR CERTIFIED AS NON-CONDUCTIVE. USING THIS HOSE ON OR NEAR ELECTRICAL LINES MAY RESULT IN DEATH OR SERIOUS INJURY.
2. FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROPERLY TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND ELEC-TRIC LINES.
3. DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE. KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT CONTACT DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION AND SEVERE PERSONAL INJURY.
4. HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, CUTTING, OR CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.D
O N
OT
RE
MO
VE
TH
IS T
AG D A N G E R
SEE OTHER SIDE SEE OTHER SIDE
HOSE TYPES
8 ► EA08 User Manual
Oil
Flow
Hos
e Le
ngth
sIn
side
Dia
met
erU
SE(P
ress
/Ret
urn)
Min
. Wor
king
Pre
ssur
eG
PMLP
MFE
ETM
ETER
SIN
CH
MM
PSI
BA
RC
ertifi
ed N
on-C
ondu
ctiv
e H
ose
- Fib
er B
raid
- fo
r Util
ity B
ucke
t Tru
cks
4-9
15-3
4up
to 1
0up
to 3
3/8
10B
oth
2250
155
Con
duct
ive
Hos
e - W
ire B
raid
or F
iber
Bra
id -D
O N
OT
USE
NEA
R E
LEC
TRIC
AL
CO
ND
UC
TOR
S4-
615
-23
up to
25
up to
7.5
3/8
10B
oth
2500
175
4-6
15-2
326
-100
7.5-
301/
213
Bot
h25
0017
5
5-10
.519
-40
up to
50
up to
15
1/2
13B
oth
2500
175
5-10
.519
-40
51-1
0015
-30
5/8
16B
oth
2500
175
5-10
.519
-40
100-
300
30-9
05/
816
Pre
ssur
e25
0017
5
3/4
19R
etur
n25
0017
5
10-1
338
-49
up to
50
up to
15
5/8
16B
oth
2500
175
10-1
338
-49
51-1
0015
-30
5/8
16P
ress
ure
2500
175
3/4
19R
etur
n25
0017
5
10-1
338
-49
100-
200
30-6
03/
419
Pre
ssur
e25
0017
5
125
.4R
etur
n25
0017
5
13-1
649
-60
up to
25
up to
85/
816
Pre
ssur
e25
0017
5
3/4
19R
etur
n25
0017
5
13-1
649
-60
26-1
008-
303/
419
Pre
ssur
e25
0017
5
125
.4R
etur
n25
0017
5
Figu
re 1
. Typ
ical
Hos
e C
onne
ctio
ns
Tool
to H
ydra
ulic
Circ
uit H
ose
Rec
omm
enda
tions
The
char
t to
the
rig
ht s
how
s re
com
men
ded
min
imum
hos
e di
amet
ers
for
vario
us h
ose
leng
ths
base
d on
gal
lons
per
min
ute
(gpm
)/lit
ers
per
min
ute
(lpm
). Th
ese
reco
mm
enda
-tio
ns a
re in
tend
ed to
kee
p re
turn
line
pre
ssur
e (b
ack
pres
sure
) to
a m
inim
um a
ccep
tabl
e le
v-el
to e
nsur
e m
axim
um to
ol p
erfo
rman
ce.
This
cha
rt is
inte
nded
to b
e us
ed fo
r hyd
raul
ic
tool
app
licat
ions
onl
y ba
sed
on S
tanl
ey H
y-dr
aulic
Too
ls to
ol o
pera
ting
requ
irem
ents
and
sh
ould
not
be
used
for a
ny o
ther
app
licat
ions
.A
ll hy
drau
lic h
ose
mus
t hav
e at
leas
t a r
ated
m
inim
um w
orki
ng p
ress
ure
equa
l to
the
max
i-m
um h
ydra
ulic
sys
tem
relie
f val
ve s
ettin
g.
All
hydr
aulic
hos
e m
ust m
eet o
r exc
eed
spec
ifica
tions
as
set f
orth
by
SAE
J517
.
PRES
SUR
E
RET
UR
N
<<<
FLO
W
FLO
W >
>>
HOSE RECOMMENDATIONS
EA08 User Manual ◄ 9
HTMA / EHTMA REQUIREMENTS
Flow Range
Nominal Operating Pressure (at the power supply outlet)
System relief valve setting (at the power supply outlet)
Maximum back pressure (at tool end of the return hose)
Measured at a max. fluid viscosity of: (at min. operating temperature)
Temperature: Sufficient heat rejection capacity to limit max. fluid temperature to: (at max. expected ambient temperature)
Min. cooling capacity at a temperature difference of between ambient and fluid temps NOTE: Do not operate the tool at oil temperatures above 140° F (60° C). Operation at higher temperatures can cause operator discomfort at the tool. Filter Min. full-flow filtration Sized for flow of at least: (For cold temp. startup and max. dirt-holding capacity)
Hydraulic fluid Petroleum based (premium grade, anti-wear, non-conductive) Viscosity (at min. and max. operating temps)
NOTE: When choosing hydraulic fluid, the expected oil temperature extremes that will be experienced in service determine the most suitable temperature viscosity characteristics. Hydraulic fluids with a viscosity index over 140 will meet the requirements over a wide range of operating temperatures.
*SSU = Saybolt Seconds Universal
4-6 gpm 7-9 gpm 9-10.5 gpm 11-13 gpm (15-23 lpm) (26-34 lpm) (34-40 lpm) (42-49 lpm) 1500 psi 1500 psi 1500 psi 1500 psi (103 bar) (103 bar) (103 bar) (103 bar)
2100-2250 psi 2100-2250 psi 2200-2300 psi 2100-2250 psi (145-155 bar) (145-155 bar) (152-159 bar) (145-155 bar)
250 psi 250 psi 250 psi 250 psi (17 bar) (17 bar) (17 bar) (17 bar)
400 ssu* 400 ssu* 400 ssu* 400 ssu* (82 centistokes) (82 centistokes) (82 centistokes) (82 centistokes)
140° F 140° F 140° F 140° F (60° C) (60° C) (60° C) (60° C)
3 hp 5 hp 6 hp 7 hp (2.24 kW) (3.73 kW) (5.22 kW) (4.47 kW) 40° F 40° F 40° F 40° F (22° C) (22° C) (22° C) (22° C)
25 microns 25 microns 25 microns 25 microns 30 gpm 30 gpm 30 gpm 30 gpm (114 lpm) (114 lpm) (114 lpm) (114 lpm)
100-400 ssu* 100-400 ssu* 100-400 ssu* 100-400 ssu* (20-82 centistokes)
HTMA HYDRAULIC SYSTEM REQUIREMENTS
NOTE: These are general hydraulic system requirements. See tool specification page for tool specific requirements
TOOL TYPE
HTMA / EHTMA REQUIREMENTS
TYPE I TYPE II TYPE IIITYPE RR
B C D3.5-4.3 gpm 4.7-5.8 gpm 7.1-8.7 gpm 9.5-11.6 gpm 11.8-14.5 gpm(13.5-16.5 lpm) (18-22 lpm) (27-33 lpm) (36-44 lpm) (45-55 lpm)1870 psi 1500 psi 1500 psi 1500 psi 1500 psi(129 bar) (103 bar) (103 bar) (103 bar) (103 bar)
EHTMA HYDRAULIC SYSTEM REQUIREMENTS
CLASSIFICATION
Flow Range
Nominal Operating Pressure (at the power supply outlet)
System relief valve setting (at the power supply outlet)
2495 psi 2000 psi 2000 psi 2000 psi 2000 psi(172 bar) (138 bar) (138 bar) (138 bar) (138 bar)
10 ► EA08 User Manual
PRE-OPERATION PROCEDURESPREPARATION FOR INITIAL USEThe handles and torque tube, which are shipped unat-tached, must be connected to the tool prior to opera-tion. An optional auger bit must also be connected to the tool for proper operation. Inspect the tool to assure the tool was not damaged in shipping and does not contain packing debris.
CHECK HYDRAULIC POWER SOURCE1. Using a calibrated flowmeter and pressure gauge,
check that the hydraulic power source develops a flow of 4–9 gpm/15–34 lpm at 2000 psi/140 bar.
2. Make certain the hydraulic power source is equipped with a relief valve set to open at 2100–2250 psi/145–155 bar minimum.
3. Check that the hydraulic circuit matches the tool for open-center (OC) operation.
INSTALL HANDLESRefer to the assembly instructions provided with the tool.1. Install the handles (1) and fasteners (2). Tighten
each fastener to 40 ft. lbs./54 Nm.
CHECK TOOL1. Make sure all tool accessories are correctly in-
stalled. Failure to install tool accessories properly can result in damage to the tool or personal injury.
2. There should be no signs of leaks.3. The tool should be clean, with all fittings and fasten-
ers tight.
CHECK TRIGGER MECHANISM1. Check that the trigger operates smoothly and is free
to travel between the ON–OFF–ON positions.
INSTALL AUGER BITThe EA08 Earth Auger accepts a standard 1-3/8 inch female hex socket.1. Align the hole on the auger chuck with the hole in
the coupler (15). 2. Slide the auger chuck into the coupler. Secure it us-
ing the clevis pin (33) and hairpin cotter (34).
Figure 2. Installing the Auger
INSTALL TORQUE TUBE1. The torque tube is attached to the base as shown
in Figure 3. Be sure to use the cotterless clevis pin provided with the unit. Make sure the pin is pushed through both holes in the base.
2. The opposite end of the tube can be connected to a solid object, such as the Stanley hydraulic power unit, a trailer hitch ball, ground stake, etc.
Figure 3. Installing Torque Tube
CONNECT HOSES1. Wipe all hose couplers with a clean lint-free cloth
before making connections.2. Connect the hoses from the hydraulic power source
to the hose couplers on the tool. It is a good prac-tice to connect the return hose first and disconnect it last to minimize or avoid trapped pressure within the tool.
OPERATION
EA08 User Manual ◄ 11
3. Observe flow indicators stamped on hose couplers to be sure that oil will flow in the proper direction. The female coupler is the inlet coupler.
NOTE:The pressure increase in uncoupled hoses left in the sun may result in making them difficult to connect. When possible, connect the free ends of operating hoses together.
OPERATING PROCEDURES1. Observe all safety precautions.2. Make sure the torque tube is attached to the base of
the EA08 and anchored to a solid object.NOTE:It is recommended to always use the torque tube.3. Position yourself so that you are able to operate the
ON/OFF trigger with your right hand. Grasp each handle firmly. Your helper positions himself/herself directly opposite and facing you and grasping each handle firmly.
4. Lift the EA08, with auger attached, and position the auger so it is perpendicular to where you intend to dig. The auger should be just above (not touching) the ground.
5. With your feet, and your helper’s feet, spread and firmly planted, squeeze the ON/OFF trigger fully to start the auger turning.
6. Lower the EA08 until the auger starts digging. With soft soil the auger will penetrate into the ground with little effort and may require you to apply a slight lift to the EA08. With hard soil the auger cannot pene-trate the ground easily and may require you to apply some down pressure to the EA08. Try not to apply enough down pressure to stall the auger. Augering in different soils requires different techniques and practice to become proficient.
7. After reaching the desired depth, lift the auger straight out of the hole. Always release the ON/OFF trigger before the tip of the auger reaches the top of the hole.
COLD WEATHER OPERATIONIf the tool is to be used during cold weather, preheat the hydraulic fluid at low engine speed. When using the nor-mally recommended fluids, fluid temperature should be at or above 50 °F/10 °C (400 ssu/82 centistokes) before use.
OPERATION
12 ► EA08 User Manual
If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem.When diagnosing faults in operation of the tool, always check that the hydraulic power source is supplying the cor-rect hydraulic flow and pressure to the tool as listed in the table. Use a flowmeter known to be accurate. Check the flow with the hydraulic oil temperature at least 80 °F/27 °C.
SYMPTOM CAUSE SOLUTIONEarth auger does not run. Power unit not functioning. Check power unit for proper flow
and pressure (4–9 gpm/15–34 lpm, 2000 psi/140 bar).
Couplers or hoses blocked. Remove restriction.Pressure and return line hoses reversed at ports.
Be sure hoses are connected to their proper ports.
Poor earth auger performance. Power unit not functioning. Check power unit for proper flow and pressure (4–9 gpm/15–34 lpm, 2000 psi/140 bar).
Couplers or hose blocked. Remove restriction.Fluid too hot (above 140 °F/60 °C). Provide cooler to maintain proper
fluid temperature.Earth auger operates slow. Low oil flow from power unit. Check power source for proper
flow.High back-pressure. Check hydraulic system for
excessive back-pressure and correct as required.
TROUBLESHOOTING
EA08 User Manual ◄ 13
Pressure Range................................................................................................................................ 2000 psi/140 barMaximum Back Pressure...................................................................................................................... 250 psi/17 barCouplers .........................................................................................HTMA/EHTMA Flush Face Type Male & FemaleConnect Size and Type ...................................................................................................... 1/2 in. Male Pipe AdapterWeight .....................................................................................................................................................47 lbs/21 kgOverall Length ...................................................................................................................................... 41 in./104 cmOverall Width ........................................................................................................................................... 30 in./76 cmOverall Height (Less Auger) ................................................................................................................ 12 in. /30.5 cmMaximum Fluid Temperature .................................................................................................................. 140 °F/60 °CHTMA Class I ..............................................................................................................................4–6 gpm @ 2000 psi
EHTMA Category ........................................................................................................................ 20 lpm @ 138 barHTMA Class II .............................................................................................................................7–9 gpm @ 2000 psi
EHTMA Category ........................................................................................................................ 30 lpm @ 138 bar
ACCESSORIESDESCRIPTION PART NUMBER2 in. Dia. × 42 in. OAL (Requires 58585 Coupler) .............................................................................................474063 in. Dia. × 42 in. OAL (Requires 58586 Coupler) .............................................................................................474074 in. Dia. × 42 in. OAL .......................................................................................................................................474086 in. Dia. × 42 in. OAL .......................................................................................................................................474098 in. Dia. × 42 in. OAL .......................................................................................................................................4741010 in. Dia. × 42 in. OAL ..................................................................................................................................... 4741112 in. Dia. × 42 in. OAL .....................................................................................................................................4741216 in. Dia. × 42 in. OAL .....................................................................................................................................4741318 in. Dia. × 42 in. OAL .....................................................................................................................................47414Digging Tooth with Hardface ..............................................................................................................................474292 in. Center Screw Bit, 6–12 in. .........................................................................................................................474303 in. Center Screw Bit ........................................................................................................................................474314 in. Center Screw Bit ........................................................................................................................................4743213/16 × 1-3/8 in. Hex Coupler for use with 47406 Auger ...................................................................................585851-1/8 × 1-3/8 in. Hex Coupler for use with 47407 Auger....................................................................................58586Coupler, 1-1/4 inch Hex Assy. ............................................................................................................................65477
SOUND POWER AND VIBRATION DECLARATIONMeasured A-weighted sound power level, Lwa (ref. 1pW) in decibels 96 dBAUncertainty, Kwa, in decibels 3 dBAMeasured A-weighted sound pressure level, Lpa (ref. 20 µPa) at operator’s position, in decibels 81.5 dBA
Uncertainty, Kpa, in decibels 3 dBAValues determined according to noise test code given in ISO 15744, using the basic standard ISO 3744 NOTE:The sum of a measured noise emission value and its associated uncertainty represents an upper boundary of the range of values which is likely to occur in measurements.Declared vibration emission value in accordance with EN 12096Measured vibration emission value: a 6.3 m/sec²Uncertainty: K 2.3 m/sec²Values determined according to ISO 8662-1, ISO 5349-1,2
SPECIFICATIONS
14 ► EA08 User Manual
EA08 PARTS ILLUSTRATION
EA08 User Manual ◄ 15
ITEMPART NO. QTY DESCRIPTION
1 37919 3 HANDLE
2 39415 4 CAPSCREW
3 39276 1 MOTOR (PARKER TB-0165-F-S-10-0-AAAB
4 37917 1 BASE ASSY
5 06151 4 CAPSCREW
6 — 2 CLEVIS PIN (FURNISHED WITH ITEM 28)
7 00720 1 SET SCREW
8 — 1 KEY (FURNISHED WITH ITEM 3)
9 11207 1 CIRCUIT TYPE D STICKER
10 11206 1 CIRCUIT TYPE C STICKER
11 28323 1 CE STICKER
12 00719 3 NUT, NYLOCK
13 39423 1 COMPOSITE DECAL
14 39277 1 VALVE MOUNT HANDLE
15 43662 1 COUPLER, 1-3/8 HEX
00718 1 CAPSCREW
19 39404 2 ELBOW
20 03974 1 COUPLER SET
21 39279 1 TRIGGER
22 — 2 COTTER PIN (INCL WITH ITEM 28)
23 08253 3 CAPSCREW
24 39283 1 HOSE, LONG
25 39282 1 HOSE, SHORT
26 10351 2 ADAPTER
28 39278 1 VALVE, BRAND A0755-T-4-J-S
29 37923 1 TORQUE TUBE ASSY
30 23139 1 NAME TAG
31 21181 1 PIN
32 39424 1 WARNING DECAL
33 44908 1 CLEVIS PIN
34 44909 1 HAIRPIN COTTER
66409 1 SOUND POWER LEVEL DECAL (NOT SHOWN)
EA08 PARTS LIST
Stanley Hydraulic Tools3810 SE Naef Road
Milwaukie, Oregon 97267-5698 USA(503) 659-5660 / Fax (503) 652-1780
www.stanleyhydraulics.com