G12 A 0.003 A A 0.003 A Standard Toolholder - DIN69871 Form A/AD/B/ADB ER Collet Chuck DIN69871 Shank a ±0.1 b (H12) d d1 G d3 (H7) d5 ±0.05 d6 d8 max f1 ±0.1 f2 min f3 -0.1 L1 -0.3 L4 min L5 -0.3 L6 -0.4 L7 -0.4 e1 ±0.1 d12 Taper AT3 30 3.2 16.1 7 31.75 M12 13 59.30 50 45 11.1 35 19.1 47.80 24 15.0 16.4 19.0 21 4 0.002 40 3.2 16.1 7 44.45 M16 17 72.30 63.55 50 11.1 35 19.1 68.40 32 18.5 22.8 25.0 27 4 0.003 50 3.2 25.7 7 69.85 M24 25 107.25 97.50 80 11.1 35 19.1 101.75 47 30.0 35.5 37.7 42 6 0.004 Designation Dimension (mm) L L1 D D1 G J DIN69871 40 ER 16 X 100 BIN 100 45 28 44 M16 M10 DIN69871 40 ER 16 X 160 BIN 160 86 28 44 M16 M10 DIN69871 40 ER 20 X 100 BIN 100 51 34 44 M16 M12 DIN69871 40 ER 20 X 160 BIN 160 87 34 44 M16 M12 DIN69871 40 ER 25 X 100 BIN 100 51 42 44 M16 M16 X 1.5 DIN69871 40 ER 25 X 160 BIN 160 88 42 44 M16 M16 X 1.5 DIN69871 40 ER 32 X 100 BIN 100 35 50 60 M16 M22 X 1.5 DIN69871 40 ER 32 X 160 BIN 160 95 50 60 M16 M22 X 1.5 DIN69871 40 ER 40 X 100 BIN 100 35 63 60 M16 M28 X 1.5 • (1) Preset balanced value AT3 Taper G2.5 (1) 20,000 RPM 58~ 60 HRc N5 Balanceable Rings LRef L1Ref D G J Designation Range Dimension (mm) L L1 D D1 G J DIN69871 30 ER 16 X 63 (1) 0.5 - 10 63 28 28 - M12 M10 DIN69871 40 ER 16 X 63 0.5 - 10 63 - 28 - M16 M10 DIN69871 40 ER 16 X 100 0.5 - 10 100 - 28 - M16 M10 DIN69871 40 ER 16 X 160 0.5 - 10 160 85 28 40 M16 M10 DIN69871 40 ER 20 X 63 1 - 13 63 - 34 - M16 M12 DIN69871 40 ER 20 X 100 1 - 13 100 - 34 - M16 M12 DIN69871 40 ER 20 X 160 1 - 13 160 91 34 44 M16 M12 DIN69871 50 ER 16 X 100 (1) 0.5 - 10 100 - 28 - M24 M10 DIN69871 50 ER 16 X 160 (1) 0.5 - 10 160 85 28 40 M24 M10 DIN69871 50 ER 16 X 200 (1) 0.5 - 10 200 110 28 40 M24 M10 DIN69871 50 ER 20 X 100 (1) 1 - 13 100 - 34 - M24 M12 DIN69871 50 ER 20 X 160 (1) 1 - 13 160 86 34 45 M24 M12 DIN69871 50 ER 25 X 200 (1) 1 - 6 200 85 42 55 M24 M16 • Add B for coolant through flange (1) Balance to G6.3 at 12,000 RPM DIN 69871 Form AD DIN 6499 AT3 Taper G2.5 20,000 RPM 58~ 60 HRc N5 J G D LRef L1Ref D1 DIN 69871 Form AD DIN 6499 T-BALANCE Type “AD” Coolant Hole Type “ADB” Coolant Hole or Coolant Through Flange Type “B” Coolant Through Flange A-A A-A Type “A” d12 30º A A 20º A A e1 e1 f3 f1 a f2 d3 L1 L4 d1 d8 d6 d5 L5 L5 L7 L6 8 17' 50'' b d G G79 Pull Stud User Guide G85 - G96 ER Collet G67 - G71 NUT G78 Wrench G81 Preset Screw G80 For non-stock items: supply condition is subject to availability. If not available in stock then MOQ (minimum order qty) will be applicable.
10
Embed
DIN69871 - EURO ISSA 40 ER 25 X 100 BIN 100 51 42 44 M16 M16 X 1.5 ... DIN 69871 Form AD DIN 6499 T-BALANCE Type “AD” Coolant Hole Type “ADB”
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
G12
CONTACT RATIO A 0.003 A
CONTACT RATIO A 0.003 A
Standard Toolholder - DIN69871 Form A/AD/B/ADB
ER Collet Chuck
DIN69871
Shank a ±0.1 b (H12) d d1 G d3 (H7) d5 ±0.05 d6 d8 max f1 ±0.1 f2 min f3 -0.1 L1 -0.3 L4 min L5 -0.3 L6 -0.4 L7 -0.4 e1 ±0.1 d12 Taper AT3
L L1 D D1 G JDIN69871 40 ER 16 X 100 BIN 100 45 28 44 M16 M10DIN69871 40 ER 16 X 160 BIN 160 86 28 44 M16 M10DIN69871 40 ER 20 X 100 BIN 100 51 34 44 M16 M12DIN69871 40 ER 20 X 160 BIN 160 87 34 44 M16 M12DIN69871 40 ER 25 X 100 BIN 100 51 42 44 M16 M16 X 1.5DIN69871 40 ER 25 X 160 BIN 160 88 42 44 M16 M16 X 1.5DIN69871 40 ER 32 X 100 BIN 100 35 50 60 M16 M22 X 1.5DIN69871 40 ER 32 X 160 BIN 160 95 50 60 M16 M22 X 1.5DIN69871 40 ER 40 X 100 BIN 100 35 63 60 M16 M28 X 1.5
• (1) Preset balanced value
CONTACT RATIO
AT3 TaperG2.5(1)
20,000 RPMCONTACT RATIO
58~60 HRcCONTACT RATIO
N5
Balanceable Rings
LRefL1Ref
DG J
Designation RangeDimension (mm)
L L1 D D1 G JDIN69871 30 ER 16 X 63(1) 0.5 - 10 63 28 28 - M12 M10DIN69871 40 ER 16 X 63 0.5 - 10 63 - 28 - M16 M10DIN69871 40 ER 16 X 100 0.5 - 10 100 - 28 - M16 M10DIN69871 40 ER 16 X 160 0.5 - 10 160 85 28 40 M16 M10DIN69871 40 ER 20 X 63 1 - 13 63 - 34 - M16 M12DIN69871 40 ER 20 X 100 1 - 13 100 - 34 - M16 M12DIN69871 40 ER 20 X 160 1 - 13 160 91 34 44 M16 M12DIN69871 50 ER 16 X 100(1) 0.5 - 10 100 - 28 - M24 M10DIN69871 50 ER 16 X 160(1) 0.5 - 10 160 85 28 40 M24 M10DIN69871 50 ER 16 X 200(1) 0.5 - 10 200 110 28 40 M24 M10DIN69871 50 ER 20 X 100(1) 1 - 13 100 - 34 - M24 M12DIN69871 50 ER 20 X 160(1) 1 - 13 160 86 34 45 M24 M12DIN69871 50 ER 25 X 200(1) 1 - 6 200 85 42 55 M24 M16
• Add B for coolant through flange (1) Balance to G6.3 at 12,000 RPM
DIN 69871 Form AD DIN 6499
CONTACT RATIO
AT3 TaperG2.5
20,000 RPMCONTACT RATIO
58~60 HRcCONTACT RATIO
N5
JG
D
LRefL1Ref
D1
DIN 69871 Form AD DIN 6499 T-BALANCE
Type “AD” Coolant Hole
Type “ADB” Coolant Hole or Coolant Through Flange
Type “B” Coolant Through Flange
A-A A-A
Type “A”
d12
30º
A
A
20ºA
A
e1
e1
f3f1a
f2
d3
L1
L4d1
d8 d6 d5L5
L5
L7L68 17' 50''
b
d
G
G79
Pull Stud User Guide
G85 - G96
ER Collet
G67 - G71
NUT
G78
Wrench
G81
Preset Screw
G80
For non-stock items: supply condition is subject to availability. If not available in stock then MOQ (minimum order qty) will be applicable.
G13
CONTACT RATIO A 0.003 A
CONTACT RATIO A 0.003 A
CONTACT RATIO A 0.003 A
Designation RangeDimension (mm)
L L1 D D1 G JDIN69871 30 ER 32 X 65(1) 2 - 20 65 32 50 404 M12 M18X1.5DIN69871 40 ER 25 X 65 1 - 16 65 28 42 32.4 M16 M16X2DIN69871 40 ER 25 X 100 1 - 16 100 - 42 - M16 M16X2DIN69871 40 ER 25 X 150 1 - 16 150 - 42 - M16 M16X2DIN69871 40 ER 32 X 65 2 - 20 65 32 50 40.4 M16 M22X1.5DIN69871 40 ER 32 X 100 2 - 20 100 35 50 49 M16 M22X1.5DIN69871 40 ER 32 X 150 2 - 20 150 35 50 49 M16 M22X1.5DIN69871 40 ER 40 X 70 3 - 26 70 32 63 50.4 M16 M28X1.5DIN69871 40 ER 40 X 100 3 - 26 100 32 63 50.4 M16 M28X1.5DIN69871 50 ER 25 X 100(1) 1 - 16 100 - 42 - M24 M16X2DIN69871 50 ER 25 X 150(1) 1 - 16 150 80.9 42 50 M24 M16X2DIN69871 50 ER 25 X 200(1) 1 - 16 200 85 42 55 M24 M16X2DIN69871 50 ER 32 X 100(1) 2 - 20 100 - 50 - M24 M22X1.5DIN69871 50 ER 32 X 150(1) 2 - 20 150 - 50 - M24 M22X1.5DIN69871 50 ER 32 X 200(1) 2 - 20 200 - 50 - M24 M22X1.5DIN69871 50 ER 40 X 100(1) 3 - 26 100 - 63 - M24 M28X1.5DIN69871 50 ER 40 X 150(1) 3 - 26 150 - 63 - M24 M28X1.5DIN69871 50 ER 40 X 200(1) 3 - 26 200 - 63 - M24 M28X1.5DIN69871 50 ER 50 X 100(1) 10 - 34 100 - 78 - M24 M36X1.5DIN69871 50 ER 50 X 150(1) 10 - 34 150 - 78 - M24 M36X1.5
ER Collet Chuck
DIN 69871 Form AD DIN 6499
DesignationDimension (mm)
L L1 D J G G1
DIN69871 40 ER 32 SHORT 28.6 9.5 40 M16 M16 M40 X 1.5
DIN69871 50 ER 32 SHORT 28.6 9.5 40 M22 X 1.5 M24 M40 X 1.5
DIN69871 50 ER 40 SHORT 28.6 9.5 50 M28 X 1.5 M24 M50 X 1.5
DIN 69871 Form AD DIN 6499 T-SHORT
• Tightening torque: 24kg × m
• Add B for coolant through flange (1) Balance to G6.3 at 12,000 RPM
• Add B for coolant through flange
DIN69871
JGLRef
L1Ref
LRef L1Ref
CONTACT RATIO
AT3 TaperG2.5
20,000 RPMCONTACT RATIO
58~60 HRcCONTACT RATIO
N5
CONTACT RATIO
AT3 TaperG2.5
20,000 RPMCONTACT RATIO
58~60 HRcCONTACT RATIO
N5
DesignationDimension (mm)
L D G1
DIN69871 40 ER 32 CLICK-IN 20.1 41 M16
DIN69871 50 ER 32 CLICK-IN 20.1 41 M24
DIN 69871 Form AD DIN 6499 T-CLICKL
DER
CONTACT RATIO
AT3 TaperG2.5
20,000 RPMCONTACT RATIO
58~60 HRcCONTACT RATIO
N5
D
D1
D
G79
Pull Stud User Guide
G85 - G96
ER Collet
G67 - G71
NUT
G78
Wrench
G81
ER 32 SRF
G75
Preset Screw
G80
For non-stock items: supply condition is subject to availability. If not available in stock then MOQ (minimum order qty) will be applicable.
• Add B for coolant through flange (1) Balance to G6.3 at 12,000 RPM
CONTACT RATIO
AT3 TaperG2.5
20,000 RPMCONTACT RATIO
58~60 HRcCONTACT RATIO
N5
CONTACT RATIO
AT3 Taper
CONTACT RATIO58~60 HRcCONTACT RATIO
N5
Max :D+1.3
Min :D-0.3
The bore section is made from two circular sections.The clamping screwpushes the drill shankthrough a narrowopening that forces elastic deformation of the holder.Contact is made aroundmore than 180° -providing a highclamping force.
G79
Pull Stud Lock Screw
G80
User Guide
G85 - G96
NUT
G78
TSK Collet
G72
Preset Screw
G80
For non-stock items: supply condition is subject to availability. If not available in stock then MOQ (minimum order qty) will be applicable.
D1 L L1 D GDIN69871 40 EM 10 X 45 10 45 25.9 35 M16DIN69871 40 EM 12 X 45 12 45 25.9 42 M16DIN69871 40 EM 14 X 45 14 45 25.9 44 M16DIN69871 40 EM 16 X 45 16 45 25.9 48 M16DIN69871 40 EM 18 X 45 18 45 25.9 49 M16DIN69871 40 EM 20 X 45 20 45 25.9 49 M16DIN69871 40 EM 25 X 45 25 45 25.9 49 M16
CONTACT RATIO58~60 HRcCONTACT RATIO A 0.005 ACONTACT RATIO
N5
D
DD1
TAP HOLDER
MILLING CHUCK
COMPRESSION(F1) TENSION(F2)
G79
Pull Stud Lock Screw
G80
User Guide
G85 - G96
ER Collet
G67 - G71
NUT
G78
Wrench
G81
ST Collet
G74 G76
Tap AdapterFor non-stock items: supply condition is subject to availability. If not available in stock then MOQ (minimum order qty) will be applicable.
G16
CONTACT RATIO A 0.005 A
CONTACT RATIO A 0.005 A
DesignationDimension (mm)
D1 L D GDIN69871 40 EM 6 X 50E 6 50 25 M16DIN69871 40 EM 8 X 50E 8 50 28 M16DIN69871 40 EM 10 X 50E 10 50 35 M16DIN69871 40 EM 12 X 50E 12 50 42 M16DIN69871 40 EM 14 X 63E 14 63 44 M16DIN69871 40 EM 16 X 63E 16 63 48 M16DIN69871 40 EM 18 X 63E 18 63 50 M16DIN69871 40 EM 20 X 63E 20 63 52 M16DIN69871 40 EM 25 X 100E 25 10 65 M16DIN69871 40 EM 32 X 100E 32 100 72 M16DIN69871 50 EM 6 X 63E 6 63 25 M24DIN69871 50 EM 6 X 83E 8 63 28 M24DIN69871 50 EM 10 X 63E 10 63 35 M24DIN69871 50 EM 12 X 63E 12 63 42 M24DIN69871 50 EM 14 X 63E 14 63 44 M24DIN69871 50 EM 16 X 63E 16 63 48 M24DIN69871 50 EM 18 X 63E 18 63 50 M24DIN69871 50 EM 20 X 63E 20 63 52 M24DIN69871 50 EM 32 X 100E 32 100 72 M24DIN69871 50 EM 40 X 100E 40 100 90 M24
DesignationDimension (mm)
D1 L D GDIN69871 30 EM 6 X 50 6 50 26 M12DIN69871 30 EM 8 X 50 8 50 28 M12DIN69871 30 EM 10 X 50 10 50 35 M12DIN69871 30 EM 12 X 50 12 50 42 M12DIN69871 30 EM 14 X 63 14 63 44 M12DIN69871 30 EM 16 X 63 16 63 48 M12DIN69871 30 EM 18 X 72 18 72 50 M12DIN69871 30 EM 20 X 72 20 72 52 M12DIN69871 40 EM 6 X 50 6 50 25 M16DIN69871 40 EM 8 X 50 8 50 28 M16DIN69871 40 EM 10 X 50 10 50 35 M16DIN69871 40 EM 12 X 50 12 50 42 M16DIN69871 40 EM 16 X 63 16 63 48 M16DIN69871 40 EM 18 X 63 18 63 50 M16DIN69871 40 EM 20 X 63 20 63 52 M16DIN69871 40 EM 25 X 100 25 100 65 M16DIN69871 40 EM 32 X 100 32 100 71 M16DIN69871 50 EM 6 X 63 6 63 25 M24DIN69871 50 EM 8 X 63 8 63 28 M24DIN69871 50 EM 10 X 63 10 63 35 M24DIN69871 50 EM 12 X 63 12 63 42 M24DIN69871 50 EM 14 X 63 14 63 44 M24DIN69871 50 EM 16 X 63 16 63 48 M24DIN69871 50 EM 18 X 63 18 63 50 M24DIN69871 50 EM 20 X 63 20 63 52 M24DIN69871 50 EM 25 X 80 25 80 65 M24DIN69871 50 EM 32 X 100 32 100 72 M24DIN69871 50 EM 40 X 100 40 100 90 M24DIN69871 50 EM 50 X 125 50 125 98 M24
End Mill Holder
• Add B for coolant through flange except DIN 69871 30
DIN 69871 Form AD DIN 6359/DIN1835 Form B
End Mill Holder - Whistle Notch
• The adjustment screw has an internal coolant hole Add B for coolant through the flange
DIN 6359/DIN1835 Form EDIN 69871 Form AD
LG
D1 ≤ Ø20 D1 ≥ Ø25
D1 ≤ Ø20 D1 ≥ Ø25
L
2°
G
DIN69871
CONTACT RATIO
AT3 Taper
CONTACT RATIO58~60 HRcCONTACT RATIO
N5
CONTACT RATIO
AT3 Taper
CONTACT RATIO58~60 HRcCONTACT RATIO
N5
DD1
DDD1 D1
G79
Pull Stud Lock Screw
G80
Preset Screw
G80
For non-stock items: supply condition is subject to availability. If not available in stock then MOQ (minimum order qty) will be applicable.
D1 L L1 D GDIN69871 30 SEM 16 X 35 16 35 17 38 M12DIN69871 30 SEM 22 X 50 22 50 19 47 M12DIN69871 30 SEM 27 X 50 27 50 21 58 M12DIN69871 40 SEM 16 X 35 16 35 17 38 M16DIN69871 40 SEM 22 X 35 22 35 19 47 M16DIN69871 40 SEM 27 X 60 27 60 21 58 M16DIN69871 40 SEM 32 X 60 32 60 24 66 M16DIN69871 40 SEM 40 X 60 40 60 27 82 M16DIN69871 50 SEM 16 X 35 16 35 17 38 M24DIN69871 50 SEM 22 X 35 22 35 19 47 M24DIN69871 50 SEM 22 X 50 X 200 22 200 19 50 M24DIN69871 50 SEM 27 X 35 27 35 21 58 M24DIN69871 50 SEM 32 X 35 32 35 24 66 M24DIN69871 50 SEM 32 X 78 X 370 40 370 24 78 M24DIN69871 50 SEM 40 X 50 40 50 27 82 M24DIN69871 50 SEM 50 X 60 50 60 30 95 M24
Face Mill Arbor
• Wrench not included
DIN 69871 Form A ISO 3937
L1L
G
• If the “B type” option is required, the plug screw must be removed from the flange cooling hole (use a 2 mm hex key)
DesignationDimension (mm)
D1 D L L1 L2 GDIN69871 50 SEM 22X48X200C 22 48 200 19 181 M24DIN69871 50 SEM 22X61X300C 22 61 300 19 281 M24DIN69871 50 SEM 27X61X300C 27 61 300 21 281 M24DIN69871 50 SEM 32X78X370C 32 78 370 24 351 M24
DIN69871 Form ADB DIN3937
Extra Long Face Mill Arbor with Coolant Hole
L2L
D1 D
DIN69871
L4
D2D1 D3
L2minL2max
30°
L
J
• Add B for coolant through flange
(1) Balance to G2.5 at 10,000 RPM
CONTACT RATIO
AT3 TaperG2.5
15,000 RPMCONTACT RATIO
58~60 HRcCONTACT RATIO
N5
CONTACT RATIO
AT3 Taper
CONTACT RATIO58~60 HRcCONTACT RATIO
N5
CONTACT RATIO
AT3 Taper
CONTACT RATIO58~60 HRcCONTACT RATIO
N5
DD1
G79
Pull Stud User Guide
G85 - G96
Lock Screw
G80
Spare Parts
G80 - G81G73
THC ColletFor non-stock items: supply condition is subject to availability. If not available in stock then MOQ (minimum order qty) will be applicable.
• If the “B type” option is required, the plug screw must be removed from the flange cooling hole (use a 2 mm hex key) (1) Balance to G6.3 at 12,000 RPM
CONTACT RATIO
AT3 TaperG2.5
25,000 RPMCONTACT RATIO
58~60 HRcCONTACT RATIO
N5
G79
Pull Stud User Guide
G85 - G96
For non-stock items: supply condition is subject to availability. If not available in stock then MOQ (minimum order qty) will be applicable.