Dielectric Properties of Ceramics EBB 443 Dr. Sabar D. Hutagalung School of Materials & Mineral Resources Engineering, Universiti Sains Malaysia.

Dielectric Properties of CeramicsEBB 443

Dr. Sabar D. HutagalungSchool of Materials & Mineral Resources Engineering, Universiti Sains Malaysia

IntroductionIntroduction Dielectric materials: high electrical

resistivities, but an efficient supporter of electrostatic fields.

Can store energy/charge. Able to support an electrostatic field while

dissipating minimal energy in the form of heat. The lower the dielectric loss (proportion of

energy lost as heat), the more effective is a dielectric material.

Another consideration is the dielectric constant, the extent to which a substance concentrates the electrostatic lines of flux.

Dielectric Constant The capacitance, C, of a capacitor formed by two

parallel plates of area A spaced d apart with the area between the plates filled with dielectric material with a relative dielectric constant of ε is:

Dielectric Loss

For a lossy (imperfect) dielectric the dielectric constant can be represented by a complex relative dielectric constant:

The imaginary part of this complex dielectric constant, ε at a frequency, ω is equivalent to a frequency-dependent conductivity, σ(ω), given by:

ε" is also known as the loss factor. The small difference in phase from ideal behaviour is

defined by an angle δ, defined through the equation

tan δ is known as the loss tangent or dissipation factor.

A quality factor, Q, for the dielectric is given by the reciprocal of tan δ.

Dielectric Loss

Equivalent circuit diagrams: (a) capacitive cell, (b) charging and loss current, (c) loss tangent for a typical dielectric

Dielectric Loss

From Q = oAV/d = CV

If V being sinusoidal, total charge Q may be written as

Current flow on discharge of the capacitive cell in time, t:

For a real dielectric the current I has vector components IC and IR:

I = IC + IR

tio eVCQ

CVidt

dQI

Dielectric Loss

From magnitude of these currents, also we can define a dissipation factor, tan , as

Quality factor Q is:

C

R

I

Itan

cycleperdissipatedenergy

storedenergyaverageQ

tan

1

Dielectric Loss

Alternating Current Theory

Impedance of a resistance = R Impedance of a capacitance = 1/iωC Mean power, P, dissipated over a cycle in a lossy

capacitor with plates of area A separated by a distance d:

Dielectric Strength

Dielectric materials are insulators (conduction cannot generally occur).

However, under certain conditions, dielectric materials can break down and conduct a significant current.

Generally, the lattice of a dielectric has sufficient strength to absorb the energy from impacting electrons that are accelerated by the applied electric field.

However, under a sufficiently large electric field, some electrons present in the dielectric will have sufficient kinetic energy to ionize the lattice atoms causing an avalanching effect.

As a result, the dielectric will begin to conduct a significant amount of current.

Dielectric Strength This phenomenon is called dielectric breakdown and the

corresponding field intensity is referred to as the dielectric breakdown strength.

Dielectric strength may be defined as the maximum potential gradient to which a material can be subjected without insulating breakdown, that is

where DS is the dielectric strength in kV/mm,

VB the breakdown voltage, and d the thickness.

d

V

dx

dVDS B

max

Current-voltage characteristic up to breakdown for a typical dielectric materials

Dielectric Strength

Dielectric strength depends on material homogeneity, specimen geometry, electrode shape and disposition, stress mode (ac, dc or pulsed) and ambient condition.

CapacitorsCapacitors

Tantalum capacitor

CapacitorsCapacitors The basic formula for the capacitance of a parallel-plate

capacitor is:

To increase C, one either increases , increases A, or decreases d.

Early capacitors consisted of metal foils separated by wax ( ~ 2.5), mica ( ~ 3 - 6), steatite ( ~ 5.5 - 7.5), or glass ( ~ 5 - 10).

The use of titania provided a significant increase ( ~ 170), was followed by perovskite-based, such as BaTiO3 ( ~ 1000).

CapacitorsCapacitors

C = "capacitance"    = q /V

Units:  Coulomb/Volt           = Farad (F)-----------------------------The capacitance of a capacitor is constant; if q increases, Vincreases proportionately.

     Michael Faraday

          (1791-1867)

CapacitorsCapacitors

CapacitorsCapacitors

DRAM chips currently utilize capacitors with Si3N4 or SiO2 as dielectric materials.

The electrodes are made of doped Si or poly-Si. Capacitors can be fabricated onto IC chips. They are commonly used in conjunction with transistors in

DRAM. The capacitors help maintain the contents of memory. Because of their tiny physical size, these components have

low capacitance. They must be recharged thousands of times per second or

the DRAM will lose its data.

Q = CVQ: charge (Coulomb)

C: capacitance (Farad)

V: potential difference (Volt)

d: separation/thickness (meter)

o: permitivity of vacuum =

8.854x10-12 C2/m2 or F/m

r: dielectric constant

d

AC or

d

AVQ or

Multilayer Ceramic CapacitorMultilayer Ceramic Capacitor

The multilayer ceramic capacitor (MLCC):

where N is the number of stacked plates. Ideally, the dielectric should have a low electrical

conductivity so that the leakage current is not too large.

d

NAC or

)1(

Multilayer Ceramic CapacitorMultilayer Ceramic Capacitor

Cut-away view of multilayer ceramic capacitor.

Ceramic surface-mount capacitors.

High-K Dielectric

The bit count of MOS DRAM devices is continuously increasing. However, as bit count goes up, capacitor cell area goes down.

The capacitance per cell must remain in the 25-30 fF range, which means the capacitance density must increase.

One approach for DRAM manufacturing is to replace the traditional silicon nitride + silicon oxide with a higher dielectric constant (k) such as tantalum pentoxide (Ta2O5), Hf-oxide (HfO2) and Zr-oxide (ZrO2).

The roadmap of capacitor with DRAM technology.

D.-S. Yoon et al. / Progress in Materials Science 48 (2003) 275–371

High-K Dielectric

High-k dielectric films are anticipated to be required for certain applications with low power and leakage current specifications.

High-k materials should be compatible with conventional industry standard MOSFET process flows using a poly-Si gate electrode.

HfO2, ZrO2, and Ta2O5 as high-k gate-dielectrics.

HfO2/Poly-Si high-k transistor

ZrO2/Poly-Si high-k transistors

Typical material stack used in aTa2O5 DRAM capacitor

A Review of High High-k DielectricsA Review of High High-k Dielectrics

Gate dielectric materials having high dielectric constant, large band gap with a favorable band alignment, low interface state density and good thermal stability are needed for future gate dielectric applications.

Ultra high-k materials such as STO (SrTiO3) or BST (BaSrTiO3) may cause fringing field induced barrier lowering effect.

High-k gate dielectrics have a number of difficulties: (1) crystallization upon heating, (2) dopant penetration, (3) fixed charge, (4) low channel mobility and (5) uncontrolled oxide formation at the Si/high-k

interface.

A Review of High High-k DielectricsA Review of High High-k Dielectrics

High-K Problems

High-K and PolySi are Incompatible

Phonon Scattering in High-K

The Gate Stack

Schematic illustration of important regions in a CMOS FET gate stack

Expected performance trends for complementary metal oxidesemiconductor (CMOS) transistor

technologies. The unrelenting reduction in transistor size and the associated decrease in gate delay for (a)

an NMOS transistor and (b) a PMOS FET are evident.

Schematic image of MOS transistors in the year 2003 and 2013.

EOT- equivalent oxide thickness

Physical and electrical thickness of high-k gate dielectric (ideal). SiO2 equivalent thickness EOT is smaller than high-k physical thickness.

The depletion region of thickness Wd forms adjacent to the poly-Si/oxide interface.

For example, if the capacitor dielectric is SiO2, teq = 3.90 (A/C), 8.85x10-3

fF/m, thus a capacitance density of C/A=34.5 fFm corresponds to teq =10 Å.

A dielectric with a relative permittivity of 16 results in a physical thickness of ~40 Å, to obtain teq =10 Å.

Comparison of (a) stacked and (b) single-layer gate dielectrics in a hypothetical transistor gate stack. Either structure results in the same overall gate stack capacitance or equivalent oxide thickness, teq =10 Å.