Stop operation immediately, disconnect the battery, wipe off water from inside the main body and the battery. After completely dry, carry out trial firing. If the unit is not operational, please contact your local dealer for repair. No operation at all Although motor is revolving, no pellet can be fired Shooting distance becomes shorter Too loud operating noise Pellets being fallen out from barrel end If gun gets wet SYMPTOM POTENTIAL CORRECTIVE Selector lever is set to safety. Battery is not charged. Battery connector is disconnected. Battery connectors ( and ) are reversed. Motor life expired (50,000 to 60,000 rounds) or poor electrical connection. Pellets are clogged inside the magazine. Pellets are clogged in the chamber. Faulty gear. Damaged or worn chamber set. Damaged or worn piston set (O-ring,piston spring). Something is jammed in the inner barrel. Faulty BB pellets (too small or heavy). Shrotage of silicone oil. Gear problem caused by too many blank firing. Worn or damaged gear. Gear problem caused by too many blank firing. Damaged or worn chamber set. No hop setting. Faulty BB Pellets (too small or heavy). Set the selector lever to Semi. Charge the battery. Attach the connector. Connect the connector correctly(check the fuse) Replace the dead motor (can be purchased from local dealer or directly G&G). Check and repair the contacts. Insert the charging rod into the magazine and move up and down a few times to remove clogged pellets. Remove clogged pellets by using the cleaning rod. Pruchase the replacement gear from your dealer or G&G and repair. Mount the replacement parts(Purchasing from your dealer or G&G). Use the cleaning rod and clean the inner barrel. Use the genuine G&G Pellets. Drops few drops of silicone oil from upper the chamber. Consult your dealer or G&G for overhaul maintenance, part replacement (gear,etc.) or repair. Turn the hop adjustment lever toward Hop. Use the G&G Pellets. 3 3 6 7 8 3 4 2 1 2 3 13 2 2 3 3 3 8 9 15 14 16 1 1 1 1 1 1 3 5 2 2 4 5 6 7 11 12 8 2 2 4 5 4 3 1 2 3 4 2 2 1 1 1 6 1 10 4 2 2 5 4 2 7 3 3 3 3 1 4 2 3 1 3 4 5 2 7 8 6 GC4 G26 - 12 GC4 G26 - 13 GC4 G26 - 01 GC4 G26 - 03 GC4 G26 - 02 GC4 G26 - 27 GC4 G26 - 08 GC4 G26 - 15 GC4 G26 - 16 GC4 G26 - 29 GC4 G26 - 04 GC4 G26 - 05 GC4 G26 - 09 GC4 G26 - 07 GC4 G26 - 18 GC4 G26 - 20 GC4 G26 - 26 GC4 G26 - 30 GC4 G26 - 10 GC4 G26 - 22 GC4 G26 - 24 GC4 G26 - 11 GC4 G26 - 17 GC4 G26 - 14 GC4 G26 - 19 GC4 G26 - 28 GC4 G26 - 21 GC4 G26 - 23 GC4 G26 - 25 GC4 G26 - 06 1 2 8 9 3 4 5 6 7 GC4 G26 - 01 GC4 G26 - 02 GC4 G26 - 03 GC4 G26 - 04 GC4 G26 - 05 GC4 G26 - 06 GC4 G26 - 07 GC4 G26 - 08 GC4 G26 - 09 GC4 G26 - 10 Flash Suppressor Front Barrel Set Lower Handguard Set Upper Handguard Set Hop-up Set Slip Ring Inner Barrel Upper Receiver Set Charging Handle Set Port Cover Set ► You may purchase all of the groups’ parts from G&G support Dep. ► E-Mail: support@guay2com TAIWAN Tel : +886-4-798-9000 Fax : +886-4-798-9900 No.999, Zhonghua Rd. Shengang Township, Changhua County 50955, Taiwan (R.O.C.) Chang Hua Headquarter Sales Dept. [email protected] , [email protected] Technology Support Dept. [email protected] PR Dept. [email protected] Dealer G2-201503-02-英 GC4 G26 - 11 GC4 G26 - 12 GC4 G26 - 13 GC4 G26 - 14 GC4 G26 - 15 GC4 G26 - 16 GC4 G26 - 17 GC4 G26 - 18 GC4 G26 - 19 GC4 G26 - 20 Front Frame Lock Pin Set Bolt Catch Set Selector Lever Set Magazine Catch Set Stock Washer Enhanced Rod Set Gmag-v1 Magazine Lower Receiver Set Trigger Guard Set Selector Plate Rear Frame Lock Pin Set Grip Set Motor Grip Bottom Set Gos-v1 Stock Set Gear Box Set Barrel Base Set Selector Plate Rear Sight Front Wire Windage knob (left / right adjustment) Elevation knob (up / down adjustment) PARTS LIST MAINTENANCE WHEN BB PELLETS ARE CLOGGED SIGHT ADJUSTMENT Front Sight - Flip down or up Rear Sight - Flip down or up Remove the magazine. Return the hop up dial to normal position and insert the cleaning rod from the lead edge of the inner barrel. Be aware to have the rod facing down and reaching to the end, and remove clogged pellets. The screw at bottom of the grip. Please use the screwdriver to adjust. Check the wire set contact on the motor. Adjust screw when the gear noise becomes shrilly. No operation TROUBLE SHOOTING WINDAGE ELEVATION To avoid clogging of pellets, make sure that no dirt gets into the chamber. The hop up may take 200 to 300 rounds to remove the excessive silicone oil, this is the normal operation for the gun. Do not use CRC-556, WD40 or other corrosive lubricant. For maintenance, use the silicon oil on the air nozzle, do not use other types of corrosive oil. 1 2 1. Before you clean the inner barrel, make sure the hop up is turn to normal position. 2. Take a piece of cotton cloth about 1 inch by 0.5 inch and insert one end of the cloth into the hole of the tip of the cleaning rod and wrap it around the tip. 3. Apply a drop of silicone oil or Teflon oil on the cloth and insert the cleaning rod into the inner barrel. 4. Check the cloth and repeat above steps until the cloth can't get any more dirt. 1 2 • Adult supervision required for users who are under 18 years of age. • The purchaser and user should conform to all laws governing the ownership of airsoft guns. • All products in this manual are imitation firearms and are not intended nor represented to be comparable in design, appearance, or function to any actural firearm offered by other manufacturers. • Accessories pictured are not always included with product. • Product names are trademarks of G&G, which has no affiliation to, and is not associated, or sponsored by any manufacturer of actual or imita- tion firearms. • Products may vary form those pictured. TROUBLE SHOOTING GC4 G26 - 21 GC4 G26 - 22 GC4 G26 - 23 GC4 G26 - 24 GC4 G26 - 25 GC4 G26 - 26 GC4 G26 - 27 GC4 G26 - 28 GC4 G26 - 29 GC4 G26 - 30 INSTRUCTION MANUAL GC4 G26 A1 BLK/DST GC4 G26 A1 BLK/DST
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Stop operation immediately, disconnect the battery, wipe off water from inside the main body and the battery. After completely dry, carry out trial firing. If the unit is not operational, please contact your local dealer for repair.
No operation at all
Although motor is revolving, no pellet can be fired
Shooting distance becomes shorter
Too loud operating noise
Pellets being fallen out from barrel end
If gun gets wet
SYMPTOM POTENTIAL CORRECTIVESelector lever is set to safety.Battery is not charged.Battery connector is disconnected.Battery connectors ( and ) are reversed.Motor life expired (50,000 to 60,000 rounds) or poor electrical connection.
Pellets are clogged inside the magazine.
Pellets are clogged in the chamber.Faulty gear.Damaged or worn chamber set.Damaged or worn piston set (O-ring,piston spring).Something is jammed in the inner barrel.Faulty BB pellets (too small or heavy).Shrotage of silicone oil.Gear problem caused by too many blank firing.Worn or damaged gear.Gear problem caused by too many blank firing.Damaged or worn chamber set.No hop setting.Faulty BB Pellets (too small or heavy).
Set the selector lever to Semi.Charge the battery.Attach the connector.Connect the connector correctly(check the fuse)Replace the dead motor (can be purchased from local dealer or directly G&G). Check and repair the contacts.Insert the charging rod into the magazine and move up and down a few times to remove clogged pellets.Remove clogged pellets by using the cleaning rod.Pruchase the replacement gear from your dealer or G&G and repair.
Mount the replacement parts(Purchasing from your dealer or G&G).
Use the cleaning rod and clean the inner barrel.Use the genuine G&G Pellets.Drops few drops of silicone oil from upper the chamber.
Consult your dealer or G&G for overhaul maintenance, part replacement (gear,etc.) or repair.
Turn the hop adjustment lever toward Hop.Use the G&G Pellets.
3
3
6
7
8 34
2
12
313
22
33
3
8915
1416
1
1
1
1
1
1
35
2
2
4
56
7
1112
8
2
2
45
4
3
1
23
4
2
21
1
16
1
10
4
2
2
5
4
27
3
3
3
3
14
2
3
1
3
4
5
2
7
8
6
GC4 G26 - 12
GC4 G26 - 13
GC4 G26 - 01
GC4 G26 - 03
GC4 G26 - 02
GC4 G26 - 27
GC4 G26 - 08
GC4 G26 - 15
GC4 G26 - 16
GC4 G26 - 29
GC4 G26 - 04
GC4 G26 - 05
GC4 G26 - 09
GC4 G26 - 07
GC4 G26 - 18
GC4 G26 - 20
GC4 G26 - 26
GC4 G26 - 30
GC4 G26 - 10
GC4 G26 - 22
GC4 G26 - 24
GC4 G26 - 11
GC4 G26 - 17
GC4 G26 - 14
GC4 G26 - 19
GC4 G26 - 28
GC4 G26 - 21
GC4 G26 - 23
GC4 G26 - 25
GC4 G26 - 06
1
2
89
3
456
7
GC4 G26 - 01GC4 G26 - 02GC4 G26 - 03GC4 G26 - 04GC4 G26 - 05GC4 G26 - 06GC4 G26 - 07GC4 G26 - 08GC4 G26 - 09GC4 G26 - 10
Flash SuppressorFront Barrel SetLower Handguard SetUpper Handguard SetHop-up SetSlip RingInner BarrelUpper Receiver SetCharging Handle SetPort Cover Set
► You may purchase all of the groups’ parts from G&G support Dep.► E-Mail: support@guay2com
TAIWAN
Tel : +886-4-798-9000 Fax : +886-4-798-9900No.999, Zhonghua Rd. Shengang Township, Changhua County 50955, Taiwan (R.O.C.)
ChangHua
Headquarter
Sales Dept. [email protected] , [email protected] Support Dept. [email protected] Dept. [email protected]
Dealer
G2-201503-02-英
GC4 G26 - 11GC4 G26 - 12GC4 G26 - 13GC4 G26 - 14GC4 G26 - 15GC4 G26 - 16GC4 G26 - 17GC4 G26 - 18GC4 G26 - 19GC4 G26 - 20
Front Frame Lock Pin SetBolt Catch SetSelector Lever SetMagazine Catch SetStock WasherEnhanced Rod SetGmag-v1 MagazineLower Receiver SetTrigger Guard SetSelector Plate
Rear Frame Lock Pin SetGrip SetMotorGrip Bottom SetGos-v1 Stock SetGear Box SetBarrel Base SetSelector PlateRear SightFront Wire
Windage knob (left / right adjustment)Elevation knob (up / down adjustment)
PARTS LIST
MAINTENANCE
WHEN BB PELLETS ARE CLOGGEDSIGHT ADJUSTMENT
Front Sight - Flip down or upRear Sight - Flip down or up
Remove the magazine. Return the hop up dial to normal position and insert the cleaning rod from the lead edge of the inner barrel.
Be aware to have the rod facing down and reaching to the end, and remove clogged pellets.
The screw at bottom of the grip. Please use the screwdriver to adjust.
Check the wire set contact on the motor.
Adjust screw when the gear noise becomes shrilly.
No operation
TROUBLE SHOOTING
WINDAGE
ELEVATION
To avoid clogging of pellets, make sure that no dirt gets into the chamber.The hop up may take 200 to 300 rounds to remove the excessive silicone oil, this is the normal operation for the gun.
Do not use CRC-556, WD40 or other corrosive lubricant.
For maintenance, use the silicon oil on the air nozzle, do not use other types of corrosive oil.
12
1. Before you clean the inner barrel, make sure the hop up is turn to normal position.2. Take a piece of cotton cloth about 1 inch by 0.5 inch and insert one end of the clothinto the hole of the tip of the cleaning rod and wrap it around the tip.
3. Apply a drop of silicone oil or Teflon oil on the cloth and insert the cleaning rod into the inner barrel.4. Check the cloth and repeat above steps until the cloth can't get any more dirt.
12
• Adult supervision required for users who are under 18 years of age.• The purchaser and user should conform to all laws governing the ownership of airsoft guns. • All products in this manual are imitation firearms and are not intended nor represented to be comparable in design, appearance, or function to any actural firearm offered by other manufacturers.• Accessories pictured are not always included with product. • Product names are trademarks of G&G, which has no affiliation to, and is not associated, or sponsored by any manufacturer of actual or imita-tion firearms. • Products may vary form those pictured.
TROUBLE SHOOTING
GC4 G26 - 21GC4 G26 - 22GC4 G26 - 23GC4 G26 - 24GC4 G26 - 25GC4 G26 - 26GC4 G26 - 27GC4 G26 - 28GC4 G26 - 29GC4 G26 - 30
INSTRUCTION MANUAL
GC4 G26 A1 BLK/DSTGC4 G26 A1 BLK/DST
Related Documents
