DBALL2-NISS4HT EN IG NF20170222...2017/02/22 · Nissan JUKE & Nissan Sentra ONLY OR Installation Type 1 - with THNISS3 T-Harness [1] These wires are optional connections only required
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
LED Diagnostics & Troubleshooting...........................................................................................................................
® Infiniti & Nissan are registered trademarks and property of their respective companies.
Index
Installation Guide
Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.
Key2GO is required for this firmware.
Important:
This guide is compatible with the NISS4HT firmware version 2.20 and higher.
The NISS4HT firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Infiniti and Nissan vehicles.
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to the Module Programming section on pages 18-19 for more information.
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
The table below lists the vehicles and features which are compatible with this product. Refer to the following pages for more information on installation wiring, programming and troubleshooting for these vehicles.
Vehicles
2016
2015
2014
2013
2012
2011
2010
2009
PK
-Im
mobili
zer
Bypass-D
ata
No
Key
Req'd
AV
-Park
ing
Lig
hts
Contr
ol
DL-A
rmF
acto
ryS
ecurity
DL-D
isarm
Facto
ryS
ecurity
DL-D
oor
Lock
Contr
ol
DL-D
oor
Unlo
ck
DL-D
river
Priority
Unlo
ck
DL-S
lidin
gD
oor
Contr
olD
river
DL-S
lidin
gD
oor
Contr
olP
assenger
DL-T
runk
/H
atc
hR
ele
ase
FO
B-C
ontr
olof
aft
erm
ark
et
ala
rmw
ith
OE
Mre
mote
Key2G
O
PK
-Push
To
Sta
rtIg
nitio
nC
om
patible
RS
-Tach
/R
PM
Outp
ut
SS
-Entr
yM
onitoring
ALL
Door
Pin
s
SS
-Entr
yM
onitoring
Driver
Door
Pin
SS
-Entr
yM
onitoring
Hood
Pin
SS
-Entr
yM
onitoring
Tru
nk/H
atc
hP
in
ST
-Bra
ke
Sta
tus
(foot
bra
ke)
ST
-E-B
rake
Sta
tus
ST
-Ignitio
nS
tatu
s
ST
-Keysense
Sta
tus
Infiniti
M35h (Smart Key) * 1 1 • • • • • • • • D • • • • D • • • • • D
M37 (Smart Key) 1 1 1 • • • • • • • • D • • • • D • • • • W D
M56 (Smart Key) 1 1 1 • • • • • • • • D • • • • D • • • • W D
Q70 (Smart Key) 1 1 1 • • • • • • • • D • • • • D • • • • • D
QX56 (Smart Key) 1 1 1 • • • • • • • • D • • • • D • • • • W D
QX80 (Smart Key) 1 1 1 • • • • • • • • D • • • • D • • • • • D
Nissan
Cube (Smart Key) 1 1 1 1 1 1 • • • • • • • • D • • • • D • • • • • D
JUKE (Smart Key) 1 1 1 1 1 1 • • • • • • • • D • • • • D • • • • • D
LEAF (Smart Key) 2 • • • • • • • • D • • • • D • • • • • D
Sentra (Smart Key) 1 1 1 1 • • • • • • • • D • • • • D • • • • W D
Versa (Smart Key) 3 3 3 3 • • • • • • • • D • • • • D • • • • • D
Versa Note (Smart Key) 4 4 4 • • • • • • • • D • • • • D • • • • • D
* The Infiniti M35h (Smart Key) is not compatible with the THNISS3 T-Harness.
Legend:
D: Data-to-Data (D2D) only
•: D2D and Wire-to-Wire (W2W)
PK: Transponder & Immobilizer Override
AV: Horn & Lights Controls
DL: OE Door Lock & Alarm Controls
FOB: Sync CAN Interface w/ FOB Remote
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
When armed, the aftermarket alarm (if available) will sound if the trunk is opened using the OEM passive entry request button near the trunk. To avoid this, open the trunk using the OEM fob button, aftermarket transmitter or SmartStart application. Alternately, you can disarm the aftermarket alarm before opening the trunk.
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
This feature is mandatory to control the immobilizer override in this firmware.
Key2GO has been designed and developed to bypass the advanced encryption layers found in modern vehicles. It uses an array of servers to generate a duplicate of the original key, allowing the installation of a remote starter without having to give up a key.
The advantage is that this feature allows you to use one original key and the server to configure the bypass in the vehicle.
All Key2GO-compatible firmware are clearly indicated in the function list of each vehicle search result page and will also appear on the flash page. Any first-time user must re-register to gain access to Key2GO, and some additional information will be required to complete the registration process, such as your Directed account number and store name. Key2GO requires an XKLoader.
Refer to page 19 of this guide for instructions on how to program features using Key2GO.
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
Do not use in a standard installation. Use the toggle switch supplied with the remote starter for a working Remote Start Safety Override Switch.
Brake SwitchT-Harness
(+) 12V
D2Donly
1 8
169
55
54
53
52
51
50
45
46
48
49
44
43
42
41
47
70
69
68
67
66
65
60
61
63
64
59
58
57
56
62(-) Driver Door Trigger: Pin 47
(+)12V: Pin 70
Junction - Black 15-pin conn.(left of steering column)
BCM (left of steering column
or behind instrument cluster -Nissan Quest)
Junction - White 15-pin conn.(left of steering column)
(-) PTS: Pin 4
PTS - Brown or White 8-pin conn. (at PTS switch)
14 5 6 7 8
32
OR
(-) PTS: Pin 8
(-) Ground
Nissan JUKE &Nissan Sentra ONLY
OR
Installation Type 1 - with THNISS3 T-Harness
[1] These wires are optional connections only required if features “OEM Security Disarm on Data” & “Door Lock Control On Data” are disabled. See Feature & Option List section.
[2] These connections are only required if the feature does not operate in data.
Page 4
(-) Push-To-Start Output: Green/Black
Remote Start Safety Override Switch
White/Black N.C.
(+) Ignition Status Output: Violet/Brown
(+) Ignition Status Input: Violet/Green
(-) RAP Off Output: Red/Black
XKD2D65
TX
(-) Ground
RX
(+) 12V
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
B01
Q70 (Smart Key)
QX80 (Smart Key)
Cube (Smart Key)
2011-2015 JUKE (Smart Key)
Quest (Smart Key)
Sentra (Smart Key)
M37 (Smart Key)
M56 (Smart Key)
B02
2016 JUKE (Smart Key)
QX56 (Smart Key)
T-HarnessTHNISS3D(optional)
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
Immo. Data Interrupt (conn.side): Orange/Yellow: 9
14 5 6 7 8
32
Installation Type 2 - without T-HarnessPage 10
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.[2] These connections are only required if the feature does not operate in data.
10
DBALL2
RF
Prog. Button
LED
4
XKD2D65TX
RX
(+) 12V
14
12
2
(-) Ground
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
Lock, Unlock and Parking Light wires must be connected if the door lock and OEM alarm are not controlled by data.
See features 5 & 7 in Feature and Option List section.
Do not use in a standard installation. Use the toggle switch supplied with the remote starter for a working Remote Start Safety Override Switch.
Clock & Data Wireat NATS
Connector (behind Push-to-Start
button)See Vehicle Wiring Reference Chart for
wire location.
B-01 B-02
Brake SwitchT-Harness
(+) 12V
D2Donly
1 8
169
PTS - Brown 8-pin conn.(PTS switch)
(-) PTS: Blue, pin 8
12345 6 7 8
1
2(+)12V: Green, pin 1
Black 2-pin conn.(drivers kick)
(-) Driver Door Trigger: Lt.Blue,
pin 18
BCMBlack 24-pin conn.
(left of steering column)
[2] (-) Lock, (-) Unlock wires & Parking Light
B01
Versa (Smart Key)
(-) Ground
20
21
23
24
19
17
16
22
15
14
13
9
11
12
7
6
5
4
10
3
2
1
18
8
(-) Push-To-Start Output: Green/Black
(+) Ignition Status Output: Violet/Brown
(+) Ignition Status Input: Violet/Green
(-) RAP Off Output: Red/Black
Installation Type 3 - with THNISS3 T-Harness Page 12
[1] These wires are optional connections only required if features “OEM Security Disarm on Data” & “Door Lock Control On Data” are disabled. See Feature & Option List section.
[2] These connections are only required if the feature does not operate in data.
Remote Start Safety Override Switch
White/Black N.C.
XKD2D65
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
TX
(-) Ground
RX
(+) 12V
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.[2] These connections are only required if the feature does not operate in data.
10
DBALL2
RF
Prog. Button
LED
4
XKD2D65TX
(-) Ground
RX
(+) 12V
14
12
2
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
Lock, Unlock and Parking Light wires must be connected if the door lock and OEM alarm are not controlled by data.
See features 5 & 7 in Feature and Option List section.
Do not use in a standard installation. Use the toggle switch supplied with the remote starter for a working Remote Start Safety Override Switch.
Clock & Data Wireat NATS Connector (behind Push-to-Start
button)See Vehicle Wiring Reference Chart for
wire location..
B-01 B-02
Brake SwitchT-Harness
(+) 12V
D2Donly
1 8
169
PTS - White 8-pin conn.(at PTS switch)
12345 6 7 8
(-) Push-to-Start: Blue or Red, pin 8
(-) Driver Door Trigger: Lt.Blue,
pin 18Junction - White 24-pin conn.(at drivers kick)
(+)12V: Green, pin 11
2
Black 2-pin conn.(at drivers kick)
OBDII Diagnostic 16-pin Connector
[2] (-) Lock, (-) Unlock wires & Parking Light
B01
Versa Note� (Smart Key)
20
21
23
24
19
17
16
22
15
14
13
9
11
12
7
6
5
4
10
3
2
1
18
8
Installation Type 4 - with THNISS3 T-Harness Page 15
[1] These wires are optional connections only required if features “OEM Security Disarm on Data” & “Door Lock Control On Data” are disabled. See Feature & Option List section.
XKD2D65
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
TX
(-) Ground
RX
(+) 12V
[2] These connections are only required if the feature does not operate in data.
(-) Push-To-Start: Green/Black
(+) Ignition Status Output: Violet/Brown
(+) Ignition Status Input: Violet/Green
(-) RAP Off Output: Red/Black
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.[2] These connections are only required if the feature does not operate in data.
Remove the backup key from the transmitter.Open the transmitter, remove the battery.
REMOVEBATTERY
CR 20323V
REMOVETHE KEY
Ensure that every keyfob except one is located a minimum of 10 feet (3 meters) away from the vehicle BEFORE proceeding with the programming sequence.
Hold the keyfob in front of PTS button for steps 4 to 6.
Place and hold the keyfob in front of PTS button. Place keyfob
in front of
PTS button
2
3
1Solid
Wait until the LED turns ON solid red.
Note: To skip the transponder programming and use convenience features only, press the programming button 5 times.
Go to the next page to complete the module programming.
ImportantMake all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.
Warning! To take advantage of advanced features, you must use XpressVIP 4.5 (and higher) or the Directechs Mobile app.
When the flashing operation is successful, you can proceed with the programming instructions below.
Refer to the LED Diagnostics section on pages 23-24 for more information and for troubleshooting purposes.
OR
If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses to the module, then connect the 4-pin D2D harness.
D2D Installation
W2W Installation
If required for your installation, connect the 10-pin and 12-pin harnesses to the module, then connect the 14-pin harness to the module.
10-pinD2D
st1
12-pin14-pin
nd2
rd3
10-pinD2D
st1
th4
12-pin14-pin
nd2
rd3
Flashing a module using your computer:
1. Connect the interface module to your computer using the XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and select the Flash Module button.
3. Follow the instructions to select your vehicle, installation type, and configure your options.
4. Once you have configured the firmware options, click on the FLASH button.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your XKLoader3.
2. Launch the Directechs Mobile app on your smartphone or tablet.
3. Select FLASH YOUR MODULE and follow the on screen instructions.
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
5 Press the brake pedal until the LED starts flashing orange slowly then release the pedal.
Push the PTS button once to turn the ignition OFF.
Push the PTS button twice to turn ON ignition and wait for the key light to flash.
Press Release
Brakepedal
Brakepedal
Page 19
& &Flashesslowly
Push x2
Push x1
Disconnect the module and complete the Key2GO programming.
You have successfully completed the module programming sequence.
3
2
1
Once the configuration is completed, reconnect the module. The LED turns ON solid green for 3 seconds, then turns off.
Click on Submit Key2GO Request.
Remove the module from the vehicle and reconnect it to your computer. The web site will automatically recognize that you are moving onto the second phase of the programming sequence.
Refer to the LED Diagnostics section on pages 23-24 for more information and for troubleshooting purposes.Version 4.5 or higher of XpressVIP must be installed on your computer to complete this programming sequence.
Web Programming (for Key2GO)
Solid x3 Secs
&Off
You can now reassemble the key fob.4
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts to flash orange and red.
Release the programming button. The LED turns ON solid red.
Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.
1 OR
If required for your installation, connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
W2W Installation
10-pinD2D
st1
12-pin14-pin
nd2
th4
rd3
10-pinD2D
st1
th5
12-pin14-pin
nd2
rd3
th4
Hard Reset
2 & &Solid SolidRelease
Wait 3 seconds until the LED turns ON solid orange then release the programming button. The LED then turns ON solid red.
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected.
1 OR
If required for your installation, connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
W2W Installation
10-pinD2D
st1
12-pin14-pin
nd2
th4
rd3
10-pinD2D
st1
th5
12-pin14-pin
nd2
rd3
th4
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.directechs.com. The web offers more options; however, manual configuration of the features is possible using the information on this page.
Feature and Option List
*Default Option
Feat. Operation Flashes / Option Description
1. No RF Output* Module is connected to a remote starter using a standard installation.
2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).
3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).
1. Trunk* Will pop the trunk if available.
2. Right Sliding Door When available, will operate the right sliding door.
3. Left Sliding Door When available, will operate the left sliding door.
1. Trunk Will pop the trunk if available.
2. Right Sliding Door* When available, will operate the right sliding door.
3. Left Sliding Door When available, will operate the left sliding door.
1. Trunk Will pop the trunk if available.
2. Right Sliding Door When available, will operate the right sliding door.
3. Left Sliding Door* When available, will operate the left sliding door.
1. Disabled The remote starter parking lights wire must be connected in the vehicle.
2. Enabled* The parking lights will be controlled by CAN wires.
1. Disabled The vehicle is not equipped with an OEM alarm.
2. Enabled*
This feature must be enabled when the vehicle is equipped with an OEM security alarm.
The alarm original to the vehicle is disarmed using the bypass and Push-to-Start (PTS)
button.
1. Disabled The remote starter door lock wires must be connected in the vehicle.
2. Enabled - Type1 (EU) Works for most European vehicles.
3. Enabled - Type2 (US)*Works for most North American vehicles. (We've noticed that some North American
vehicles need to be set to "Type 1 (EU)" to work properly.)
1 RFTD Output Type
2 Trunk
3 Aux1
6 OEM Security Disarm On Data
7 Door Lock Control On Data
4 Aux2
5 Parking Light Control On Data
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
To enter feature programming routine- Turn the ignition ON, then OFF. - Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the
Programming button.- The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate
the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat until a new command is entered.
Changing feature options- Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. - The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green
slowly the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.
Accessing another feature- Press and release the programming button a number of times to advance from the current feature to the next desired feature. - The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to
indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.
Once a feature is programmed- Other features can be programmed.- The feature programming can be exited.
Exiting feature programming- No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming
sequence.OR
- Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming sequence.
Feature ProgrammingProgramming
Button
Page 22
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
Clutch Relay Output: White, pin 1
Clutch Relay Input: White/Brown, pin 2
Clutch Relay Common:Yellow/Red, pin 2
Clutch Relay N.C.:Orange/Red, pin 2
CUTBack Clutch Switch
1
Front Clutch Switch
21
2Clutch
Manual Transmissiononly
12
OR12
(-) Starter Output
30
86 8587
87a
30
86 8587
87a
(+) 12V
(+) 12VClutch: Pin 2
CUT
Manual Transmissiononly1 2
ClutchPedal
See Vehicle Wiring Reference Chart for wire location.
FRONT and BACK Clutch Switch
12
OR1230
86 8587
87a(+) 12V
Front Clutch Switch
Back Clutch Switch
21
See Vehicle Wiring Reference Chart for wire location.
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.
This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website at: www.directed.com
920-10012-01 2013-07
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.