This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Notes• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and a
tolerance of ±2 on CRI measurements. See the Measurements section (page 26).• Cree XLamp XP-G2 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than
the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.
* Flux values @ 25 °C are calculated and for reference only.
FLuX ChArACtEristiCs (tJ = 85 °C)
The following table provides order codes for XLamp XP-G LeDs. For a complete description of the order code nomenclature, please see
the Bin and Order Code Formats section (page 24). For definitions of the chromaticity kits, please see the Cree’s Standard Chromaticity
Kits section (page 23).
Chromaticity Minimum Luminous Flux (lm) @ 350 mA order Codes
Notes• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and a
tolerance of ±2 on CRI measurements. See the Measurements section (page 26).• Cree XLamp XP-G2 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than
the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.
* Flux values @ 25 °C are calculated and for reference only.
Chromaticity Minimum Luminous Flux (lm) @ 350 mA order Codes
Kit CCt Code Flux (lm) @ 85 °C
Flux (lm) @ 25 °C* 70 Cri typical
e2 5700 K
S4 164 180 XPGBWT-L1-0000-00LE2
S3 156 171 XPGBWT-L1-0000-00KE2
S2 148 163 XPGBWT-L1-0000-00JE2
R5 139 153 XPGBWT-L1-0000-00HE2
R4 130 143 XPGBWT-L1-0000-00GE2
R3 122 134 XPGBWT-L1-0000-00FE2
Chromaticity Minimum Luminous Flux (lm) @ 350 mA order Codes
Notes• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and a
tolerance of ±2 on CRI measurements. See the Measurements section (page 26).• Cree XLamp XP-G2 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than
the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.
* Flux values @ 25 °C are calculated and for reference only.
Chromaticity Minimum Luminous Flux (lm) @ 350 mA order Codes
Notes• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and a
tolerance of ±2 on CRI measurements. See the Measurements section (page 26).• Cree XLamp XP-G2 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than
the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.
* Flux values @ 25 °C are calculated and for reference only.
FLuX ChArACtEristiCs (tJ = 85 °C) - Continued
Chromaticity Minimum Luminous Flux (lm) @ 350 mA order Codes
Notes• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and a
tolerance of ±2 on CRI measurements. See the Measurements section (page 26).• Cree XLamp XP-G2 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than
the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.
* Flux values @ 25 °C are calculated and for reference only.
Chromaticity Minimum Luminous Flux (lm) @ 350 mA order Codes
Notes• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and a
tolerance of ±2 on CRI measurements. See the Measurements section (page 26).• Cree XLamp XP-G2 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than
the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.
* Flux values @ 25 °C are calculated and for reference only.
Chromaticity Minimum Luminous Flux (lm) @ 350 mA order Codes
Notes• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and a
tolerance of ±2 on CRI measurements. See the Measurements section (page 26).• Cree XLamp XP-G2 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than
the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.
* Flux values @ 25 °C are calculated and for reference only.
Chromaticity Minimum Luminous Flux (lm) @ 350 mA order Codes
MeasurementsThe luminous flux, radiant power, chromaticity, forward voltage and CRI measurements in this document are binning specifications only
and solely represent product measurements as of the date of shipment. These measurements will change over time based on a number
of factors that are not within Cree’s control and are not intended or provided as operational specifications for the products. Calculated
values are provided for informational purposes only and are not intended or provided as specifications.
pre-Release Qualification testingPlease read the LeD Reliability Overview for details of the qualification process Cree applies to ensure long-term reliability for XLamp
LEDs and details of Cree’s pre-release qualification testing for XLamp LEDs.
Lumen MaintenanceCree now uses standardized IeS LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LeD lumen maintenance.
For information on the specific LM-80 data sets available for this LED, refer to the public LM-80 results document.
Please read the Long-Term Lumen Maintenance application note for more details on Cree’s lumen maintenance testing and forecasting.
Please read the Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect
the LeD junction temperature.
Moisture sensitivityCree recommends keeping XLamp LeDs in the provided, resealable moisture-barrier packaging (MBP) until immediately prior to soldering.
Unopened MBPs that contain XLamp LeDs do not need special storage for moisture sensitivity.
Once the MBP is opened, XLamp XP-G2 LEDs may be stored as MSL 1 per JEDEC J-STD-033, meaning they have unlimited floor life in
conditions of ≤ 30 ºC/85% relative humidity (RH). Regardless of the storage condition, Cree recommends sealing any unsoldered LEDs
in the original MBP.
rohs ComplianceThe levels of RoHS restricted materials in this product are below the maximum concentration values (also referred to as the threshold
limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2011/65/EC (RoHS2), as
implemented January 2, 2013. RoHS Declarations for this product can be obtained from your Cree representative or from tthe Product
ecology section of the Cree website.
rEACh ComplianceREACh substances of very high concern (SVHCs) information is available for this product. Since the European Chemical Agency (ECHA)
has published notice of their intent to frequently revise the SVHC listing for the foreseeable future, please contact a Cree representative
to insure you get the most up-to-date ReACh Declaration. ReACh banned substance information (ReACh Article 67) is also available upon
Thermal vias, if present, are not shown on these drawings.
All measurements are ±.13 mm unless otherwise indicated.
side viewtop view
SIZE
TITLE
OF
REV.
SHEETC
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300Fax (919) 313-5558
4600 Silicon DriveDurham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5°.XXX ± .25.XX ± .75.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125X° ± .5°
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH: 1.6
3.30
3.30
.73
2.26
R1.53
1.30
.50
2.30.50
3.45
3.45
.58
.50
3.30
2.30
.64
.25
.75
1.01
3.30
.50
3.30
.50
1.30
3.30
3.30 REF.
3.30 REF.
1/122.000C2610-00066
OUTLINE DRAWING XPG G3
10/6/15D. CRONIN
REVISONSREV DESCRIPTION BY DATE APP'D
RECOMMENDED PCB SOLDER PAD RECOMMENDED STENCIL PATTERN(HATCHED AREA IS OPENING)
ALL DIMENSIONS ARE ± .13MM UNLESS OTHERWISE NOTED
PRIMARYALTERNATIVE
OPTICALREFERENCE
OPTICALREFERENCE
bottom view Alternate bottom view
AnodeAnode
SIZE
TITLE
OF
REV.
SHEETC
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300Fax (919) 313-5558
4600 Silicon DriveDurham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5°.XXX ± .25.XX ± .75.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125X° ± .5°
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH: 1.6
3.30
3.30
.73
2.26
R1.53
1.30
.50
2.30.50
3.45
3.45
.58
.50
3.30
2.30
.64
.25
.75
1.01
3.30
.50
3.30
.50
1.30
3.30
3.30 REF.
3.30 REF.
1/122.000C2610-00066
OUTLINE DRAWING XPG G3
10/6/15D. CRONIN
REVISONSREV DESCRIPTION BY DATE APP'D
RECOMMENDED PCB SOLDER PAD RECOMMENDED STENCIL PATTERN(HATCHED AREA IS OPENING)
ALL DIMENSIONS ARE ± .13MM UNLESS OTHERWISE NOTED
PRIMARYALTERNATIVE
OPTICALREFERENCE
OPTICALREFERENCE
SIZE
TITLE
OF
REV.
SHEETC
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300Fax (919) 313-5558
4600 Silicon DriveDurham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5°.XXX ± .25.XX ± .75.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125X° ± .5°
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH: 1.6
3.30
3.30
.73
2.26
R1.53
1.30
.50
2.30.50
3.45
3.45
.58
.50
3.30
2.30
.64
.25
.75
1.01
3.30
.50
3.30
.50
1.30
3.30
3.30 REF.
3.30 REF.
1/122.000C2610-00066
OUTLINE DRAWING XPG G3
10/6/15D. CRONIN
REVISONSREV DESCRIPTION BY DATE APP'D
RECOMMENDED PCB SOLDER PAD RECOMMENDED STENCIL PATTERN(HATCHED AREA IS OPENING)
All measurements are ±.13 mm unless otherwise indicated.
Notes:• Cree recommends using thermal pad kickouts to maximize component thermal performance.• Cree recommends using white solder mask material to minimize system optical loss.* This stencil has been tested and optimized for the avoidance of voiding when using ALPHA® LUMeT® P30 Maxrel solder paste. For
other solder pastes, a “window pane” design for the thermal pad stencil may result in a lower voiding percentage. Contact your local Cree Field Applications Engineer for consultation regarding your specific application.
recommended solder Pad(solder Mask pattern)
Recommended stencil openings*
SIZE
TITLE
OF
REV.
SHEETC
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300Fax (919) 313-5558
4600 Silicon DriveDurham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5°.XXX ± .25.XX ± .75.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125X° ± .5°
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED:
All Cree carrier tapes conform to EIA-481D, Automated Component Handling Systems Standard.
All dimensions in mm.
SIZE
TITLE
OF
REV.
SHEET
CDRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300Fax (919) 313-5558
4600 Silicon DriveDurham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °.XXX ± .25.XX ± .75.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125X° ± .5 °
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH: 1.6
Trailer160mm (min) of
empty pocketssealed with tape
(20 pockets min.)
Loaded Pockets(1000 Lamps)
Leader400mm (min.) of
empty pockets with at least 100mmsealed by tape
(50 empty pockets min.)
12.0+.3-.0
1.75±.10
4±.18±.1 2.5±.1
1/13.000
B2402-00014
XP HEW LOADING SPEC
--
--
----
----
11/29/10D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
B ADDED CATHODE AND ANODE NOTEREORIENTED DEVICE DC 2/26/12
END START
User Feed Direction
CATHODE SIDE
ANODE SIDE
User Feed Direction
7"
1.5± .1
13mm
Pocket Tape
Carrier Tape
Ø13
Ø61 ± 0.5
12.40 0+2.00
MEASURED AT HUB
12.40MEASURED AT INSIDE EDGE
16.40
SHEET 1 OF 11:2
2400-00005SIZE
TITLE
REV.
CDRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
.X ± 0.3
X° ± 2°
.XX ± .10
.X ± .25FOR SHEET METAL PARTS ONLY
.XX ± .13
X° ± 1°
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN
MILLIMETERS & BEFORE FINISH.TOLERANCE UNLESS SPECIFIED:
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 361-4770
4600 Silicon DriveDurham, N.C 27703
NOTICECREE CONFIDENTIAL. THIS PLOT AND THE INFORMATIONCONTAINED WITHIN ARE THE PROPRIETARY ANDCONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANYUNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTOF CREE, INC.
Reel, 7" x 12mm Wide
B
LIUDEZHI 2012/5/25
PS
Ø190
½öÓÃÓÚÆÀ¹À¡£°æȨËùÓÐ (c) by Foxit Software Company, 2004ÓÉ Foxit PDF Editor ±à¼-
OD 7.5''
Ø13
Ø61 ± 0.5
12.40 0+2.00
MEASURED AT HUB
12.40MEASURED AT INSIDE EDGE
16.40
SHEET 1 OF 11:2
2400-00005SIZE
TITLE
REV.
CDRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
.X ± 0.3
X° ± 2°
.XX ± .10
.X ± .25FOR SHEET METAL PARTS ONLY
.XX ± .13
X° ± 1°
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN
MILLIMETERS & BEFORE FINISH.TOLERANCE UNLESS SPECIFIED:
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 361-4770
4600 Silicon DriveDurham, N.C 27703
NOTICECREE CONFIDENTIAL. THIS PLOT AND THE INFORMATIONCONTAINED WITHIN ARE THE PROPRIETARY ANDCONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANYUNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTOF CREE, INC.
Reel, 7" x 12mm Wide
B
LIUDEZHI 2012/5/25
PS
Ø190
½öÓÃÓÚÆÀ¹À¡£°æȨËùÓÐ (c) by Foxit Software Company, 2004ÓÉ Foxit PDF Editor ±à¼-
OD 7.5''
Y
Y
X X
REF 0.59
W
F(III)
P1D11.5 MIN.
Bo
Ao
R0.2TYPICAL
REF 4.375
Ko
Other material available.(IV)
(III)
(II)
(I)
hole to centerline of pocket.Measured from centerline of sprocketholes is ± 0.20.Cumulative tolerance of 10 sprocketto centerline of pocket.Measured from centerline of sprocket hole
SECTION Y-Y
SECTION X-X
2.0 ±0.05 (I)P2
1.55 ±0.05Do
4.0 ±0.1 (II)Po
1.75
±0.1
E1
0.30 ±0.05T
REF R2.24
2.40Ko +0.0/-0.13.70
1W
F
P
+/- 0.05
+/- 0.1+0.3/-0.1
5.508.00
12.00
Ao 3.70 +/- 0.1
Bo +/- 0.1
Y
Y
X X
REF 0.59
W
F(III)
P1D11.5 MIN.
Bo
Ao
R0.2TYPICAL
REF 4.375
Ko
Other material available.(IV)
(III)
(II)
(I)
hole to centerline of pocket.Measured from centerline of sprocketholes is ± 0.20.Cumulative tolerance of 10 sprocketto centerline of pocket.Measured from centerline of sprocket hole
SECTION Y-Y
SECTION X-X
2.0 ±0.05 (I)P2
1.55 ±0.05Do
4.0 ±0.1 (II)Po
1.75
±0.1
E1
0.30 ±0.05T
REF R2.24
2.40Ko +0.0/-0.13.70
1W
F
P
+/- 0.05
+/- 0.1+0.3/-0.1
5.508.00
12.00
Ao 3.70 +/- 0.1
Bo +/- 0.1
Y
Y
X X
REF 0.59
W
F(III)
P1D11.5 MIN.
Bo
Ao
R0.2TYPICAL
REF 4.375
Ko
Other material available.(IV)
(III)
(II)
(I)
hole to centerline of pocket.Measured from centerline of sprocketholes is ± 0.20.Cumulative tolerance of 10 sprocketto centerline of pocket.Measured from centerline of sprocket hole