Construction Technology 30 Hour - Part 1 Student Workbook Issue: US120/30/2a-IQ-0201B Copyright 2005, LJ Technical Systems. No part of this Publication may be adapted or reproduced in any material form, without the prior written permission of LJ Technical Systems. Written by: LJ Technical Dept
16
Embed
Construction Technology 30 Hour - Part 1 Student · PDF fileConstruction Technology (30 hour) - 73.12 Student Workbook LJ Technical Systems SW1.2 Use your information from Table 3.2
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Construction Technology30 Hour - Part 1Student Workbook
Issue: US120/30/2a-IQ-0201B
Copyright 2005, LJ Technical Systems. No part of thisPublication may be adapted or reproduced in any material form,without the prior written permission of LJ Technical Systems. Written by: LJ Technical Dept
Construction Technology (30 hour) - 73.12 Student Workbook
LJ Technical Systems SW1.1
Assignment 1 Comparing Columns
On Table 1.1 fill in how many mass units each column was able to bear before it failed.
Type of Column Total Mass
Round
Square
Table 1.1
Assignment 2 Resources for Construction
Complete the following table.
Category Job Title Main TaskMeasures land, draws maps, lays out highways.Installs water and sewage system.Calculates time and materials for a needed for a project.Lays foundations and other stone work.Draws plans and designs some details.Applies wall covering to protect and enhance.Construct walls and other wooden structures.Designs buildings and manages construction project.Finishes interior walls ready for painting.Carries out structural, mechanical and system designs.Erects steel structures.Installs electrical system.
Table 2.1
Assignment 3 Strength of Materials
Calculate stress and strain for the sample material.
Cost of beam $ ....................(Show your workings)
Construction Technology (30 hour) - 73.12 Student Workbook
LJ Technical Systems SW1.4
Draw your beam design here...
Assignment 10 Architectural CAD (I)
Fill in the name of your Floorplan CAD file: "................................ .bmf"[Use the file convention: your CLASS ID, your INITIALS and the ASSIGNMENT NUMBER]
Construction Technology (30 hour) - 73.12 Student Workbook
LJ Technical Systems SW1.5
Assignment 12 Surveying the Site
Plot a cross section of the Site Map shown in Diagram 12.1 of the Assignment Guide.
Assignment 13 A Firm Foundation Record the deflection of the foundation sections.
Initial Reading = .................... inches.
Pile Foundation Pier FoundationsMass Unit Added Deflection Mass Unit Added Deflection
1 12 23 34 45 56 67 78 89 9
10 10Table 13.1
Construction Technology (30 hour) - 73.12 Student Workbook
LJ Technical Systems SW1.6
Assignment 14 Construction Techniques
Use this diagram to complete your pentagon and hexagon patterns.
Shade the pentagons in the diagram below.
Construction Technology (30 hour) - 73.12 Student Workbook
LJ Technical Systems SW1.7
Construction Technology (30 hour) - 73.12 Student Workbook
LJ Technical Systems SW2.1
Assignment 16 Advanced Architectural CAD (I)Fill in the name of your Floorplan CAD file: "................................ .bmf"
[Use the file convention: your CLASS ID, your INITIALS and the ASSIGNMENT NUMBER]
Assignment 17 Advanced Architectural CAD (II)Fill in the name of your Floorplan CAD file: "................................ .bmf"
[Use the file convention: your CLASS ID, your INITIALS and the ASSIGNMENT NUMBER]
Assignment 18 A Roof Over Your Head
Record your Truss design here...
Balsa Sticks used - ............... Inches Cost (based on $5 per inch)- $...........................
Total amount of units the Kingpost truss held before failing - ............................
Total amount of units your truss held before failing - ............................
Construction Technology (30 hour) - 73.12 Student Workbook
LJ Technical Systems SW2.2
Assignment 19 On the Move! - Building Dynamics
Record the frequency at which each skyscraper vibrates.
Skyscraper Frequency RangeSkyscraper 1
Skyscraper 2
Skyscraper 3
Assignment 20 Water and Waste Systems
Complete the plan for a residential plumbing system.
WH BuildingMain
SewerOutlet
Diagram 20.1
Construction Technology (30 hour) - 73.12 Student Workbook
LJ Technical Systems SW2.3
Assignment 21 Electrical Systems
Record the minimum gauge of wire required for each circuit in Diagram 21.2 of the Assignment Guide.
Plot the temperature readings for both the Wooden Roof and Insulated Roof.
10 5 6 7 8 9 11 12 13 14 15102 3 4
60
70
80
90
100
110
120
130
Temperature(°F)
Time (mins) 10 5 6 7 8 9 11 12 13 14 15102 3 4
60
70
80
90
100
110
120
130
Temperature(°F)
Time (mins)
Graph 24.1 Wooden Roof Graph 24.2 Insulated Roof
Construction Technology (30 hour) - 73.12 Student Workbook
LJ Technical Systems SW2.6
Assignment 26 Building a Truss Bridge Record the deflection of the balsa beam. Initial Reading = .................... inches.
Mass Unit Deflection Mass Unit Deflection1 2
Assignment 27 Bridges, Bridges, Everywhere! Record the deflection of the truss bridge. Initial Reading = .................... inches.
Mass Unit Deflection Mass Unit Deflection1 2
Assignment 28 Tunneling Technology Make notes as you watch the 'Introducing Eurotunnel' video...
Construction of the Tunnel: ....................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
Advantages of the Tunnel: .....................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
Using Diagram 29.2 of the Assignment Guide, arrange the letters in the right order to spell outa well-known Eurotunnel phrase.
Stage 1 2 3 4 5 6 7 8Picture Letter
Assignment 29 Problem & Solution: Designing a TechnologyLab Part 1
Fill in the name of your Technology Lab CAD file: "................................ .bmf"[Use the file convention: your CLASS ID, your INITIALS and the ASSIGNMENT NUMBER]
Construction Technology (30 hour) - 73.12 Student Workbook
LJ Technical Systems SW2.7
Draw your plot plan here
Assignment 30 Problem & Solution: Designing a TechnologyLab Part 2
Fill in the name of your Technology Lab CAD file: "................................ .bmf"[Use the file convention: your CLASS ID, your INITIALS and the ASSIGNMENT NUMBER]
Construction Technology (30 hour) - 73.12 Student Workbook
LJ Technical Systems SW2.8
CUT 1
APPLY
GLUE
CUT2
To assemble template: CUT 1 and CUT 2 to paper edges, apply glue, align overlap and join.