Concrete Technology Concrete Technology Steel (CH10) Lecture 19 Eng: Eyad Haddad Eng: Eyad Haddad
Concrete TechnologyConcrete Technology
Steel (CH10)
Lecture 19
Eng: Eyad HaddadEng: Eyad Haddad
2
1. Introduction:
In general, metals are classified into two major groups:
(1) ferrous and (2) nonferrous
A ferrous metal is one in which the principal elements is iron as in
cast, wrought iron, and steel.
A nonferrous metal is one in which the principal is not iron, as in
copper, tin, lead, nickel, and aluminum.
3
2. Ferrous Metal: Ferrous comprise three general classes of materials of construction of
construction :
1. Cast iron.
2. wrought iron.
3. Steel. Both cast iron and wrought iron have fallen in production with the
ardent
of steel, as steel tends to exhibit better engineering properties than do
cast and wrought iron.
The application of steel and steel alloys is so widespread it has been
estimated that there are over a million uses.
In construction, steel has three principal uses:
(1) structural steel. (2) Reinforcing steel. (3) Forms and pans.
4
3.Corrosion and
wear: Each year millions of dollars worth of damage to iron and steel
structures is caused by corrosion.
Further, millions of dollars are to replace worn cut parts of machine
structures.
Corrosion and wear damage take place gradually. They seldom cause
sudden or dramatic structural disasters, as parts damaged by
corrosion or wear can be replaced or repaired before failure occurs.
Most metals associated with construction materials come in contact
with water which contains dissolved oxygen or with moist air and water
into solution readily.
The rate of solution is usually retarded by a film of hydrogen forming
on the metal or by coating the metal with a protective coating. However,
oxygen will combine with the hydrogen and over a period of time will
strip it away from the metal, and thus further corrosion will result.
5
Four classifications of corrosion for metals exist:
1. Atmospheric: In atmospheric corrosion a large excess of oxygen is
available and the rate of corrosion is largely determined by the quality of
moisture in the air and the length of time on contact with the metal.
2. Water immersion: When metals are immersed in water containing
dissolved oxygen, they will corrode. If the water does not contain any
dissolved oxygen, the metal will not corrode. If the water is acidic, the
corrosion rate is increased, whereas water that is alkaline has very little
corrosion activity unless the solution is highly concentrated.
3. Soil: In soil corrosion, the most important item is the ingredient coming
in contact with the iron or steel.
4. Chemicals other than water: It is influenced by the type of chemicals
coming in contact with the iron or steel.
6
4. Protection from
corrosionThe most common protective coating against corrosion for iron and steel
is paint.
The paint coating is usually mechanically weak and it cracks and wears
out. Thus, to do a satisfactory job, the paint must be reversed every 2 or
3 years.
Before the structure is painted, it should first be cleaned and the rust
removed. For asphalt coatings are used for protection. Metals under
stress especially those beyond their elastic strength, corrode more
rapidly than do unstressed metals.
Another way of protection is via encasing the iron or steel in concrete.
7
5. Carbon steel:Carbon steel, also called plain carbon steel, is a metal alloy, a
combination of two elements, iron and carbon, where other elements are
present in quantities too small to affect the properties.
The only other alloying elements allowed in plain-carbon steel are
manganese (1.65% max), silicon (0.60% max), and copper (0.60% max).
Steel with a low carbon content has the same properties as iron, soft but
easily formed. As carbon content rises the metal becomes harder and
stronger but less ductile and more difficult to weld. Higher carbon
content lowers steel's melting point and its temperature resistance in
general.
8
5. Carbon steel: (Cont.)
Carbon content influences the yield strength of steel because they fit
into the interstitial crystal lattice sites of the body-centered cubic
arrangement of the iron molecules.
The interstitial carbon reduces the mobility of dislocations, which in turn
has a hardening effect on the iron.
To get dislocations to move, a high enough stress level must be applied
in order for the dislocations to "break away". This is because the
interstitial carbon atoms cause some of the iron BCC lattice cells to
distort.
9
Types of carbon steel:
Typical compositions of carbon:
Mild (low carbon) steel: approximately 0.05–0.29% carbon content.
Mild steel has a relatively low tensile strength, but it is cheap and
malleable. Medium carbon steel: approximately 0.30–0.59% carbon content.
Balances ductility and strength and has good wear resistance; used
for large parts, forging and automotive components. High carbon steel: approximately 0.6–0.99% carbon content. Very
strong, used for springs and high-strength wires.[4] Ultra-high carbon steel: approximately 1.0–2.0% carbon content.
Steels that can be tempered to great hardness. Used for special
purposes like (non-industrial-purpose) knives, axles or punches.
10
6. Structural steel:Structural steel is steel construction material, a profile, formed with a
specific shape or cross section and certain standards of chemical
composition and strength.
11
7. Reinforcing steel:Rebar or reinforcing steel in concrete is a great step for a lifetime of
beautiful walkways and driveways.
Reinforced concrete, also called ferroconcrete in some countries, is concrete in
which reinforcement bars ("rebars") or fibers have been incorporated to strengthen a
material that would otherwise be brittle. In industrialized countries, nearly all concrete
used in construction is reinforced concrete.
12
8. Physical properties of
steelsIn general, three principal factors influence the strength, ductility and
elastic properties of steel.
1. the carbon content.
2. the percentages of silica, sulfur, phosphorous, manganese, and
other alloying elements.
3.The heat treatment and mechanical working.
Stress Strain diagram:
The relationship between loads and deflection/stress-strain in a structure
of a member can be obtained from experimental load deflection/ stress-
strain curves
13
Stress Strain
diagram:
14
The most common tests are tension test for ductile materials (steel)
& compression test for brittle materials (concrete)