SCDL – 4 th Semester – Computer Fundamentals & Networking Concepts LIST OF ATTEMPTED QUESTIONS AND ANSWERS True/False Question Modulation is the process of sending a file from one computer to another computer. Correct Answer False Your Answer False Multiple Choice Multiple Answer Question Error correction and detection in OSI model is done by :- Correct Answer Data link Layer , Transport Layer Your Answer Data link Layer Multiple Choice Multiple Answer Question The functions of ATM layers are :- Correct Answer Routing , Switching , Multiplexing Your Answer Routing , Switching , Multiplexing Multiple Choice Single Answer Question The virtual circuit approach of packet switching is used in :- Correct Answer Data Link layer Your Answer Data Link layer Select The Blank Question ATM standard defines ________ layer. Correct Answer Three Your Answer Three Multiple Choice Single Answer Question Repeater operates in :- Correct Answer Physical layer Your Data Link layer Page 1 of 221
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Multiple Choice Multiple Answer Question Terms used to describe digital signal are :-
Correct Answer
Bit rate , Bit interval
Your Answer Bit rate , Bit interval , Band rate
Multiple Choice Multiple Answer Question The important features of a reapeter are :-
Correct Answer
Can use 10Base5 , Acts as two port node , Operates only in physical layer
Your Answer Has cable length of 500 m , Acts as two port node , Operates only in physical layer
Multiple Choice Single Answer Question A required characteristic of an online real- time system is :-
Correct Answer
No delay in processing
Your Answer No delay in processing
Multiple Choice Multiple Answer Question In modems :-
Correct Answer
Signals are converted into analog to digital , Signals are converted into digital to analog , A digital signal changes some characteristic of carrier wave
Your Answer Signals are converted into analog to digital , Signals are converted into digital to analog , Digital signal is amplified
Select The Blank Question The end-to-end delivery of the entire message is the responsibility of the ________ layer.
Correct Answer
Network
Your Answer Session
True/False Question Devices on one network can communicate with device on another network via a gateway.
Correct Answer
True
Your Answer True
Select The Blank Question The X.25 standard specifies ________ protocol layers are the serial interface gateway.
Question A machine that connects to two or more electronic mail systems and transfers mail messages among them is known as bridge.
Correct Answer FALSE
Your Answer FALSE
True/False
Question Devices on one network can communicate with devices on one another network via a utility server.
Correct Answer FALSE
Your Answer TRUE
Multiple Choice Single Answer
Question Which of the following is not a part of UDP user datagram?
Correct Answer Preamble
Your Answer Source post address
Multiple Choice Multiple Answer
Question A token passing network :-
Correct Answer Provide access to the network by only one station at a time , Can provide access only to the station which is having token , Can be either ring or bus network
Your Answer Provide access to the network by only one station at a time , Can provide access only to the station which is having token , Can be either ring or bus network
Multiple Choice Single Answer Question The access protocol used by Ethernet is :-
Correct Answer
CSMA / CD
Your Answer CSMA / CD
LIST OF ATTEMPTED QUESTIONS AND ANSWERS Select The BlankQuestion: The ________ Timer is used in termination phase.Correct Answer: Time waitedYour Answer: Keep alive Multiple Choice Multiple AnswerQuestion: Error control in DLL is based on :-Correct Answer: Damaged frames , Lost frames , Lost acknowledgements Your Answer: Lost acknowledgements , Frame length , Damaged frames Multiple Choice Single AnswerQuestion: Which organisation has developed much of the original standards?Correct Answer: IEEEYour Answer: ISO Select The BlankQuestion: A ________ is the physical connection between an end point and a switch or between two switches.Correct Answer: Transmission pathYour Answer: Virtual circuit Multiple Choice Multiple AnswerQuestion: Virtual circuit frame used in Frame Relay :-Correct Answer: Switched virtual circuit (SVC) , Permanent Virtual Circuit (PVC) , Multicast Virtual Circuit (MVC) Your Answer: Switched virtual circuit (SVC) , Multicast Virtual Circuit (MVC) , Unicast Virtual Circuit (UVC) Select The BlankQuestion: In fast Ethernet autonegotiation allows ________ negotiation.Correct Answer: Data rateYour Answer: Data rate Multiple Choice Multiple AnswerQuestion: Socket address is combination of :-Correct Answer: IP address , Port number Your Answer: Port address , IP address , IP number True/False
Question: A central computer surrounded by one or more satellite computers is called a bus network.Correct Answer: FalseYour Answer: False Multiple Choice Single AnswerQuestion: Routing between autonomous system is referred to as :-Correct Answer: Exterior routingYour Answer: Popular routing True/FalseQuestion: For efficient multicasting, a shortest path spanning tree represents the communication path.Correct Answer: TrueYour Answer: False Multiple Choice Single AnswerQuestion: Which of the following connects LAN to WAN?Correct Answer: A network gatewayYour Answer: A network bridge Multiple Choice Single AnswerQuestion: TCP is a :-Correct Answer: Stream connection oriented protocolYour Answer: Application protocol Multiple Choice Multiple AnswerQuestion: Important features of GMII :-Correct Answer: Data rate is 1000 Mbps , There is no GMII cable and connector , Management functions are included Your Answer: Data rate is 1000 Mbps , Management functions are included , Less complexity Select The BlankQuestion: In ________ multiple frames can be in transit at the same time. If there is an error only the unacknowledged frame is retransmitted.Correct Answer: Selective repeat ARQYour Answer: Go-back-N ARQ Select The BlankQuestion: In 100BaseX ________ bits of data is received from network interface card.Correct Answer: 8Your Answer: 64 Multiple Choice Multiple AnswerQuestion: IEEE 802.11 architecture supports :-Correct Answer: Basic Service Set (BSS) , Extended Service Set (ESS) Your Answer: Extended Service Set (ESS) , Modular Set , Backward compatible set True/FalseQuestion: The TCP/IP protocols treat all networks equally.Correct Answer: TrueYour Answer: True Select The BlankQuestion: The X.25 standard specifies ________ protocol layers are the serial interface gateway.
Correct Answer: 3Your Answer: 4 Multiple Choice Multiple AnswerQuestion: Medium that uses metallic conductor for transmission :-Correct Answer: Coaxial cable , Shielded twisted pair cable , Unshielded twisted pair cable Your Answer: Coaxial cable , Shielded twisted pair cable , Fiber optic cable Multiple Choice Single AnswerQuestion: For handling frame arriving protocol Frame Relay uses :-Correct Answer: FRADYour Answer: LMI True/FalseQuestion: The simultaneous transmission of data to a number of stations is known as broadcast.Correct Answer: TrueYour Answer: True Multiple Choice Multiple AnswerQuestion: Query message that ICMP supports :-Correct Answer: Echo request and reply , Time-stamp request and reply , Router solicitation and advertisement Your Answer: Echo request and reply , Data transfer , Router solicitation and advertisement Multiple Choice Single AnswerQuestion: Packets in the IP layer are called :-Correct Answer: DatagramsYour Answer: Data packets Multiple Choice Single AnswerQuestion: The main standards relating to Ethernet networks are :-Correct Answer: IEEE 802.2 and IEEE 802.3Your Answer: IEEE 802.3 and IEEE 802.4 Select The BlankQuestion: ATM defines ________ versions of application adaptation Layer(AAL).Correct Answer: FourYour Answer: Three True/FalseQuestion: The 1-4 digits are known as the country code of the NUA.Correct Answer: TrueYour Answer: True Select The BlankQuestion: Physical layer is responsible for transmitting ________ from one node to other.Correct Answer: Individual bitsYour Answer: Individual bits True/FalseQuestion: The application layer of a network defines the user's port into the network.Correct Answer: FalseYour Answer: True Multiple Choice Multiple AnswerQuestion: A repeater :-
Correct Answer: Connects segments of a LAN , Forwards every frame , Is a regenerator Your Answer: Connects segments of a LAN , Is a regenerator , Amplifies the signal Multiple Choice Single AnswerQuestion: The cable connecting a DB - 9 connector at one end to a DB 25 connector at the other end must cross- connect pin 8 at the DB-9 side to which pin at the DB - 25 side?Correct Answer: 5Your Answer: 4 True/FalseQuestion: Transmission of an IP datagram between two machines on a physical network does not involve gateways.Correct Answer: TrueYour Answer: False Multiple Choice Single AnswerQuestion: The information to be communicated in a communication system is :-Correct Answer: MessageYour Answer: Message Multiple Choice Multiple AnswerQuestion: Digital transmission is possible in :-Correct Answer: Serial mode , Parallel mode Your Answer: Serial mode , Sequential mode , Distributed mode True/FalseQuestion: Gateway is used for modulation and demodulation.Correct Answer: FalseYour Answer: True Select The BlankQuestion: In ATM, all cells of single message till destination follows the ________ path.Correct Answer: Virtual circuitYour Answer: Fixed Match The FollowingQuestion Correct Answer Your AnswerPPP An HDLC version secured passwordPAP Unsecured password Data encapsulationCHAP secured password An HDLC versionNCP Data encapsulation Unsecured password True/FalseQuestion: In frame Relay, Data Link Connection Identifier (DLCI) is used to identify virtual circuit.Correct Answer: TrueYour Answer: True Multiple Choice Single AnswerQuestion: An access method in which available BW of a link is shared in time, frequency or code?Correct Answer: CanalizationYour Answer: Random Access Multiple Choice Multiple AnswerQuestion: Categories of traditional Ethernet are :-Correct Answer: 10Base 5 , 10Base 2 , 10Base T
Your Answer: 10Base 5 , 10Base 2 , 10Base T Multiple Choice Single AnswerQuestion: As the data packet moves from the lower to the upper layers, headers are :-Correct Answer: AddedYour Answer: Modified Multiple Choice Single AnswerQuestion: Topology requires a central controller or hub.Correct Answer: StarYour Answer: Star Select The BlankQuestion: In ALOHA ________ is the uploading carrier frequency.Correct Answer: 407MHzYour Answer: 401 MHz Match The FollowingQuestion Correct Answer Your AnswerFull - duplex Simultaneous transmission in Simultaneous transmission in
both directions both directionsModem Modulator Demodulator Band width of the mediumBit Binary digit 0 and 1Synchronous High Modulator Demodulatorcommunication efficiency Select The BlankQuestion: The medium that permits the highest data rate is ________.Correct Answer: Fiber optic cableYour Answer: Fiber optic cable True/FalseQuestion: Application programs as well as all protocol software from the internet layer upward use only IP address.Correct Answer: TrueYour Answer: True Multiple Choice Multiple AnswerQuestion: Features of hub are :-Correct Answer: Hub is a broadcasting device , Hub operates at physical layer , Hub transmits signals to other Your Answer: Hub is a broadcasting device , Hub transmits signals to other Multiple Choice Multiple AnswerQuestion: LCP packets include :-Correct Answer: Configuration packets , Link termination packets , Link monitoring and debugging packets Your Answer: Configuration packets , Link termination packets , Link monitoring and debugging packets
LIST OF ATTEMPTED QUESTIONS AND ANSWERS Multiple Choice Single AnswerQuestion: Feature for sending voice through the Frame Relay is called :-
Correct Answer: VOFRYour Answer: VOFR Select The BlankQuestion: In ATM, ________ is designed to support a data stream that has a constant bit rate.Correct Answer: AAL1Your Answer: AAL1 Multiple Choice Multiple AnswerQuestion: The bit rates defines the characteristics of ATM are :-Correct Answer: Constant bit rate (CBR) , Variable data rate (VBR) , Available bit rate (ABR) Your Answer: Constant bit rate (CBR) , Variable data rate (VBR) , Available bit rate (ABR) Select The BlankQuestion: The virtual path identifier (VPI) of user to network interface (UNI) is ________ bits in length.Correct Answer: 8Your Answer: 8 Multiple Choice Single AnswerQuestion: The main advantage of ISO model is that :-Correct Answer: It allows integration of software and hardwareYour Answer: It allows integration of software and hardware Select The BlankQuestion: The OSI models consists of ________ layers.Correct Answer: SevenYour Answer: Three Multiple Choice Single AnswerQuestion: An error detecting code which is the remainder resulting from dividing the bits to be checked by a predetermined binary number, is known as :-Correct Answer: Cyclic Redundancy checkYour Answer: Error rate Multiple Choice Single AnswerQuestion: Fiber Optic Ethernet is also known as:-Correct Answer: 10BASEFYour Answer: 10BASET Multiple Choice Multiple AnswerQuestion: A star backbone network :-Correct Answer: Topology of backbone is star , The backbone is just one switch , Connects several LANs Your Answer: Topology of backbone is star , Connects several LANs , Faster than any other backbone network Multiple Choice Single AnswerQuestion: Twisted -pair Ethernet is also known as :-Correct Answer: 10BASETYour Answer: 10BASEF Match The FollowingQuestion Correct Answer Your AnswerFCS Frame check sequence Frame check sequenceI- frame User information management information
S-frames No information Supervisory framesU-frames management information User information Match The FollowingQuestion Correct Answer Your AnswerTime waited timer Termination phase Termination phaseKeep Alive Timer Prevents long idle connection Handles zero window sizePersistence timer Handles zero window size Prevents long idle connectionRetransmission timer Lost segments Establishment Phase Multiple Choice Single AnswerQuestion: Rules and procedures that describes how data will be transmitted and received are referred to as :-Correct Answer: ProtocolsYour Answer: Protocols Multiple Choice Multiple AnswerQuestion: The Types of error that Internet Control Message Protocol (ICMP) can handle are :-Correct Answer: Destination unreachable , Source quench , Redirection Your Answer: Destination unreachable , Source quench , Retransmision Multiple Choice Multiple AnswerQuestion: In digital data transmission :-Correct Answer: Baud rate is equal to bit rate , Baud rate is always smaller than the bit rate Your Answer: Baud rate is equal to bit rate , Baud rate is always smaller than the bit rate Multiple Choice Single AnswerQuestion: The cost assigned for passage of a packet through a network is called :-Correct Answer: MetricYour Answer: Metric Multiple Choice Single AnswerQuestion: Standard or thick wire Ethernet is also known as :-Correct Answer: 10BASE5Your Answer: 10BASET True/FalseQuestion: The Transreceiver in fast Ethernet is called PHY Sub-layer.Correct Answer: TrueYour Answer: True Multiple Choice Single AnswerQuestion: What is the main function of the transport layer?Correct Answer: Node-to-node deliveryYour Answer: Node-to-node delivery True/FalseQuestion: ATM can handle real time transmission.Correct Answer: TrueYour Answer: True Multiple Choice Single AnswerQuestion: For the IP address 227.12.14.87, the class of the address is :-Correct Answer: Class DYour Answer: Class B
Multiple Choice Single AnswerQuestion: Which layer in the Ethernet standard communicates with the OSI network layer?Correct Answer: LLCYour Answer: Physical Multiple Choice Single AnswerQuestion: Peer to peer communication involves:-Correct Answer: Computers to share information over a networkYour Answer: Communication between a computer and the network Multiple Choice Single AnswerQuestion: Which organization develop the original RS - 232C specification?Correct Answer: EAIYour Answer: ISO True/FalseQuestion: The root bridge has largest ID.Correct Answer: FalseYour Answer: True Multiple Choice Single AnswerQuestion: Which of the following is not a part of UDP user datagram?Correct Answer: PreambleYour Answer: Preamble True/FalseQuestion: The hierarchical use of hubs removes the length limitation of 10BaseT.Correct Answer: TrueYour Answer: False Select The BlankQuestion: The ________ timer keep a track of the time between the sending of segment and the receipt of an acknowledgement.Correct Answer: RetransmissionYour Answer: Persistence Select The BlankQuestion: In fast Ethernet ________ is not required.Correct Answer: CSMA /CDYour Answer: Line coding Multiple Choice Single AnswerQuestion: Which of the following summation operation is performed on the bits to check an error-detecting code?Correct Answer: ChecksumYour Answer: Coder-decoder Multiple Choice Multiple AnswerQuestion: Serial transmission can be :-Correct Answer: Synchronous , Asynchronous Your Answer: Synchronous , Asynchronous , Sequential True/FalseQuestion: Local area networks can transmit data using twisted -pair wiring or coaxial cables.Correct Answer: TrueYour Answer: True
Multiple Choice Multiple AnswerQuestion: Features of hub are :-Correct Answer: Hub operates at physical layer , Hub transmits signals to other , Hub is a broadcasting device Your Answer: Hub operates at physical layer , Hub transmits signals to other , Hub can be used as repeater Multiple Choice Single AnswerQuestion: A repeater :-Correct Answer: Forwards every frameYour Answer: Forwards every frame True/FalseQuestion: The data link layer, in reference to the OSI model, specifies the virtual circuit interface to packet-switched service.Correct Answer: FalseYour Answer: True Multiple Choice Single AnswerQuestion: Which organisation has developed much of the original standards?Correct Answer: IEEEYour Answer: IEEE True/FalseQuestion: Frame Relay does not provide flow control or error control, they must be provided by upper layer protocols.Correct Answer: TrueYour Answer: False Select The BlankQuestion: Most modern versions of Ethernet use ________ as the transmission medium.Correct Answer: UTPYour Answer: Coaxial cable True/FalseQuestion: The general area of data communications encompasses tele-communications.Correct Answer: FalseYour Answer: True True/FalseQuestion: A device that can convert digital signals to analog signals is a packet.Correct Answer: FalseYour Answer: True Multiple Choice Multiple AnswerQuestion: X.25 uses :-Correct Answer: Packet assembler/disassembler , Packet switched network , Access lines to public data networks Your Answer: Packet assembler/disassembler , Access lines to public data networks , A cell switched network Multiple Choice Multiple AnswerQuestion: Features that encourages the wide spread use of ATM in telecommunication are :-Correct Answer: High speed data rate , Low error rate , Low operating cost Your Answer: High speed data rate , Low error rate , Low operating cost
Multiple Choice Multiple AnswerQuestion: HDLC supports :-Correct Answer: Half duplex communication , Full duplex communication , ARQ mechanisms Your Answer: Full duplex communication , ARQ mechanisms , Pipelining Multiple Choice Multiple AnswerQuestion: Broadcasting methods are :-Correct Answer: Flooding , Multidestination routing , Reverse path forwarding Your Answer: Random routing , Multidestination routing , Reverse path forwarding Select The BlankQuestion: In fast Ethernet ________ replaces physical layer signaling.Correct Answer: Reconciliation Sub LayerYour Answer: PHY True/FalseQuestion: The transport layer provides for any format, translationer code conversion necessary to put the data into an intelligible format.Correct Answer: FalseYour Answer: True Select The BlankQuestion: The ________ timer is needed to handle the zero window size.Correct Answer: PersistenceYour Answer: Keep alive
LIST OF ATTEMPTED QUESTIONS AND ANSWERS Multiple Choice Multiple AnswerQuestion: Operational features of Ethernet are:-Correct Answer: 10 mbps rate , CSMA/CD protocol , 500 meters length Your Answer: 10 mbps rate , CSMA/CD protocol , 500 meters length Multiple Choice Multiple AnswerQuestion: The adaptive routing types are :-Correct Answer: Isolated adaptive routing , Centralized adaptive routing , Distributed adaptive routing Your Answer: Isolated adaptive routing , Centralized adaptive routing , Distributed adaptive routing True/FalseQuestion: The hierarchical use of hubs removes the length limitation of 10BaseT.Correct Answer: TrueYour Answer: True Multiple Choice Single AnswerQuestion: Which of the following is not a part of UDP user datagram?Correct Answer: PreambleYour Answer: Preamble Multiple Choice Multiple AnswerQuestion: Terms used to describe digital signal are :-Correct Answer: Bit rate , Bit interval Your Answer: Bit rate , Bit interval
Match The FollowingQuestion Correct Answer Your AnswerATM Layer Cell Length 53 bytes 53 bytesBackbone Bus or star Bus or starVirtual LAN configured by software Constant bit rateVOFR Voice over Frame RelayVoice over Frame Relay Multiple Choice Single AnswerQuestion: A repeater :-Correct Answer: Forwards every frameYour Answer: Forwards every frame Multiple Choice Single AnswerQuestion: Peer to peer communication involves:-Correct Answer: Computers to share information over a networkYour Answer: Communication between a computer and the network Multiple Choice Multiple AnswerQuestion: The Types of error that Internet Control Message Protocol (ICMP) can handle are :-Correct Answer: Destination unreachable , Source quench , Redirection Your Answer: Source quench , Retransmision , Redirection Multiple Choice Single AnswerQuestion: The performance of transmission media can be measured by :-Correct Answer: Propagation speedYour Answer: Throughput Select The BlankQuestion: A communication protocol always have ________.Correct Answer: Set of symbolsYour Answer: Network information Select The BlankQuestion: Before information can be transmitted, it must be transformed into________.Correct Answer: Electromagnetic signalsYour Answer: Electromagnetic signals Multiple Choice Multiple AnswerQuestion: A transport layer :-Correct Answer: Gives service to Application layer , Receives Service from Network layer Your Answer: Gives service to Application layer , Receives Service from Network layer True/FalseQuestion: The important characteristic of LAN is parallel transmission.Correct Answer: FalseYour Answer: True Multiple Choice Single AnswerQuestion: The main advantage of ISO model is that :-Correct Answer: It allows integration of software and hardwareYour Answer: It defines cables and connectors Multiple Choice Multiple AnswerQuestion: OSPF features are :-
Correct Answer: Multiple circuit load balancing , Converge very quickly to network topology change , Not susceptible to routing loops Your Answer: Multiple circuit load balancing , Converge very quickly to network topology change , Fixed length subnetting Select The BlankQuestion: In IPv6 only ________ can fragment.Correct Answer: Original sourceYour Answer: Router Multiple Choice Single AnswerQuestion: The identifier used for data transfer is :-Correct Answer: Virtual circuit identifier (VCI)Your Answer: Virtual circuit identifier (VCI) Multiple Choice Single AnswerQuestion: Which layer in the Ethernet standard communicates with the OSI network layer?Correct Answer: LLCYour Answer: Protocol True/FalseQuestion: Fast Ethernet is backward compatible.Correct Answer: TrueYour Answer: True Match The FollowingQuestion Correct Answer Your AnswerAuthenticate protocol PAP & CHAP PAP & CHAPBit stuffing Data Transparency Data TransparencyHDLC NRM & ABM NRM & ABMPPP phases Transition states Transition states Select The BlankQuestion: Communication between a computer and a keyboard involves________ transmission.Correct Answer: SimplexYour Answer: Simplex True/FalseQuestion: In channelization access method the available BW is shared in time, frequency and code.Correct Answer: TrueYour Answer: True True/FalseQuestion: A repeater connects two LANs of different protocols.Correct Answer: FalseYour Answer: True Select The BlankQuestion: In 100 Base TX Ethernet ________ line coding is used.Correct Answer: 4B /5BYour Answer: 4B /5B Multiple Choice Multiple AnswerQuestion: In ATM, connection between two end points is accomplished through :-Correct Answer: Transmission paths (TPs) , Virtual Paths (VPs) , Virtual circuits (VCs)
Your Answer: Transmission paths (TPs) , Virtual Paths (VPs) , Virtual circuits (VCs) Multiple Choice Single AnswerQuestion: The layer lies between the network layer and the session layer is :-Correct Answer: Transport layerYour Answer: Transport layer True/FalseQuestion: Frame Relay does not provide flow control or error control, they must be provided by upper layer protocols.Correct Answer: TrueYour Answer: False Multiple Choice Multiple AnswerQuestion: Fast Ethernet has :-Correct Answer: Data rate of 100 mbps , Auto negotiation , Reconciliation sub layer Your Answer: Data rate of 100 mbps , Auto negotiation , Reconciliation sub layer Select The BlankQuestion: Transport layer is responsible for delivery of ________ from one node to other.Correct Answer: MessageYour Answer: Message Multiple Choice Single AnswerQuestion: How many fibers connects to a FDDI dual attach station?Correct Answer: 4Your Answer: 2 Select The BlankQuestion: In ________ the sender sends a frame and waits for an acknowledgement from the receiver before sending the next frame.Correct Answer: Stop-and-wait ARQYour Answer: Stop-and-wait ARQ Multiple Choice Single AnswerQuestion: CCITT.X series standers relate primarily to which area of data communication?Correct Answer: Wide area networkYour Answer: Wide area network Multiple Choice Single AnswerQuestion: Standard or thick wire Ethernet is also known as :-Correct Answer: 10BASE5Your Answer: 10BASE5 Multiple Choice Multiple AnswerQuestion: X . 25 protocol :-Correct Answer: Allows DTE to DCE interface , Is a synchronous interface , Is approved by CCITT Your Answer: Allows DTE to DCE interface , Is a synchronous interface , Is approved by CCITT Select The BlankQuestion: A ________ path provides a connection or a set of connections between switches.Correct Answer: VirtualYour Answer: Virtual circuit True/False
Question: A medium access control technique for multiple access transmission media is amplitude.Correct Answer: FalseYour Answer: True Multiple Choice Single AnswerQuestion: In ALOHA network downloading carrier frequency is :-Correct Answer: 413 MHzYour Answer: 407 MHz Multiple Choice Multiple AnswerQuestion: Transreceiver performs the function of :-Correct Answer: Transmitting and detection , Collision , Encoding and decoding Your Answer: Transmitting and detection , Synchronization , Collision True/FalseQuestion: Repeater operates in physical layer.Correct Answer: TrueYour Answer: True True/FalseQuestion: The basic data unit in an ATM network is called a cell.Correct Answer: TrueYour Answer: True Select The BlankQuestion: The IP datagram header is ________ in length.Correct Answer: 20-60 bytesYour Answer: 20-60 bytes Multiple Choice Multiple AnswerQuestion: Broadcasting methods are :-Correct Answer: Flooding , Multidestination routing , Reverse path forwarding Your Answer: Flooding , Multidestination routing Multiple Choice Multiple AnswerQuestion: Transfer of data from CPU to peripheral devices of computer is :-Correct Answer: Serial port , Parallel port Your Answer: Serial port , Parallel port Select The BlankQuestion: Network layer is responsible for delivery of ________ from one source to other.Correct Answer: PacketsYour Answer: Packets Select The BlankQuestion: The ________ timer is needed to control a lost or discarded segment by TCP.Correct Answer: RetransmissionYour Answer: Persistence Multiple Choice Multiple AnswerQuestion: Transmission media is characterized by :-Correct Answer: Throughput , Propagation speed , Propagation time Your Answer: Throughput , Propagation speed , Propagation time
LIST OF ATTEMPTED QUESTIONS AND ANSWERS Select The BlankQuestion: A data packet is a packet header together with ________.Correct Answer: User dataYour Answer: Node address Multiple Choice Multiple AnswerQuestion: Transreceiver performs the function of :-Correct Answer: Transmitting and detection , Collision , Encoding and decoding Your Answer: Transmitting and detection , Synchronization , Encoding and decoding True/FalseQuestion: Modem is used for modulation and demodulation.Correct Answer: TrueYour Answer: True Select The BlankQuestion: In simplex transmission________.Correct Answer: Data transmission is one wayYour Answer: Data transmission is one way True/FalseQuestion: The session layer takes the communication service of the transport layer and adds application -oriented functions.Correct Answer: TrueYour Answer: True Select The BlankQuestion: The digital, voice, or video voltages are referred to as ________ signals.Correct Answer: Base bandYour Answer: Broadband Select The BlankQuestion: Before information can be transmitted, it must be transformed into________.Correct Answer: Electromagnetic signalsYour Answer: Electromagnetic signals Multiple Choice Multiple AnswerQuestion: CHAP has three steps :-Correct Answer: Sending value to user , Manipulating the value and sends the result back , Validity of information Your Answer: Sending value to user , Manipulating the value and sends the result back , Verify the result Multiple Choice Single AnswerQuestion: The information to be communicated in a communication system is :-Correct Answer: MessageYour Answer: Message Multiple Choice Multiple AnswerQuestion: A Bus backbone network :-Correct Answer: Uses star topology , Connects several LANs , Uses bus topology Your Answer: Connects several LANs , Uses bus topology , Saves BW Select The Blank
Question: The connection establishment involves a ________ handshake.Correct Answer: Two-wayYour Answer: Three-way True/FalseQuestion: A modem is only capable of modulation.Correct Answer: FalseYour Answer: False Select The BlankQuestion: A television broadcast is an example of ________ transmission.Correct Answer: SimplexYour Answer: Full - duplex Multiple Choice Single AnswerQuestion: ARQ stands for :-Correct Answer: Automatic repeat requestYour Answer: Automatic repeat request Multiple Choice Single AnswerQuestion: The communication mode that supports data in both direction at the same time is :-Correct Answer: Full -duplexYour Answer: Full -duplex True/FalseQuestion: The main purpose of a data link content monitor detect problems in protocols.Correct Answer: TrueYour Answer: False True/FalseQuestion: Fast Ethernet is backward compatible.Correct Answer: TrueYour Answer: False Select The BlankQuestion: The IP datagram header is ________ in length.Correct Answer: 20-60 bytesYour Answer: 20-60 bytes Match The FollowingQuestion Correct Answer Your AnswerFull - duplex Simultaneous transmission in Simultaneous transmission in
both directions both directionsModem Modulator Demodulator Modulator DemodulatorBit Binary digit Binary digitSynchronous communication High Highefficiency Multiple Choice Single AnswerQuestion: According to the PPP transition state diagram, options are negotiated in the :-Correct Answer: Establishing stateYour Answer: Establishing state Multiple Choice Single AnswerQuestion: HDLC is a :-Correct Answer: Bit-oriented protocol
Your Answer: Bit-oriented protocol Multiple Choice Single AnswerQuestion: The identifier used for data transfer is :-Correct Answer: Virtual circuit identifier (VCI)Your Answer: Virtual circuit identifier (VCI) Multiple Choice Multiple AnswerQuestion: In first layer of Internet model :-Correct Answer: Repeaters operate , Hubs operate Your Answer: Repeaters operate , Hubs operate , Bridges operate True/FalseQuestion: The simultaneous transmission of data to a number of stations is known as broadcast.Correct Answer: TrueYour Answer: True Select The BlankQuestion: Switched Ethernet has ________ advantage over traditional Ethernet.Correct Answer: BW sharingYour Answer: Device sharing Multiple Choice Multiple AnswerQuestion: Fast Ethernet has :-Correct Answer: Data rate of 100 mbps , Auto negotiation , Reconciliation sub layer Your Answer: Data rate of 100 mbps , Reconciliation sub layer , Thin cable Multiple Choice Single AnswerQuestion: An IP address length is :-Correct Answer: 32-bitYour Answer: 32-bit Multiple Choice Multiple AnswerQuestion: Medium that uses metallic conductor for transmission :-Correct Answer: Coaxial cable , Shielded twisted pair cable , Unshielded twisted pair cable Your Answer: Coaxial cable , Shielded twisted pair cable , Unshielded twisted pair cable Multiple Choice Single AnswerQuestion: For a 10 Mbps bit rate determine the time period of each bit transmitted :-Correct Answer: 0.1 micro secondsYour Answer: 0.1 micro seconds Multiple Choice Multiple AnswerQuestion: The adaptive routing types are :-Correct Answer: Isolated adaptive routing , Centralized adaptive routing , Distributed adaptive routing Your Answer: Centralized adaptive routing , Distributed adaptive routing , Random adaptive routing True/FalseQuestion: Gateway allows devices on one network to communicate with devices on another network.Correct Answer: TrueYour Answer: True Multiple Choice Multiple Answer
Question: Error correction and detection in OSI model is done by :-Correct Answer: Data link Layer , Transport Layer Your Answer: Physical layer , Data link Layer Multiple Choice Multiple AnswerQuestion: Channelization protocols are :-Correct Answer: TDMA , CDMA , FDMA Your Answer: TDMA , CDMA , CSMA/CD protocol Select The BlankQuestion: In Base T4 Ethernet ________ line coding is used.Correct Answer: 8B /6TYour Answer: 8B /6T Multiple Choice Single AnswerQuestion: CCITT.X series standers relate primarily to which area of data communication?Correct Answer: Wide area networkYour Answer: Asynchronous communication Multiple Choice Multiple AnswerQuestion: Issues to consider for bridge connecting different LANs :-Correct Answer: Frame format , Data size , Data rate Your Answer: Data size , Data rate , Data type Multiple Choice Single AnswerQuestion: Frame Relay operates at data rate of :-Correct Answer: 1.544 MbpsYour Answer: 1.544 Mbps Multiple Choice Single AnswerQuestion: X.21 is :-Correct Answer: Network access standard for connecting stations to a circuit-switched networkYour Answer: A method access control technique for multiple-access transmission media True/FalseQuestion: Transmission of an IP datagram between two machines on a physical network does not involve gateways.Correct Answer: TrueYour Answer: True True/FalseQuestion: An Ethernet frame contains seven fields.Correct Answer: TrueYour Answer: False Multiple Choice Single AnswerQuestion: In which method, primary station controls transmission to and from secondary station?Correct Answer: Polling AccessYour Answer: Reservation Match The FollowingQuestion Correct Answer Your AnswerDigital Transmission Data transmission from hard Asynchronous transmission
disk to memorySimplex Common in one direction only Common in one direction onlyDuplex Common in both direction only Common in both direction only
Analog Transmission Door-Darshan transmission Data transmission from hard disk tomemory
Multiple Choice Multiple AnswerQuestion: The important features of a reapeter are :-Correct Answer: Can use 10Base5 , Acts as two port node , Operates only in physical layer Your Answer: Can use 10Base5 , Acts as two port node , Operates only in physical layer Multiple Choice Single AnswerQuestion: The physical path over which a message travels is :-Correct Answer: MediaYour Answer: Media Select The BlankQuestion: In ________ multiple frames can transmit at the same time. If there is an error, retransmission begins with the last acknowledged frame even if subsequent frames have arrived correctly.Correct Answer: Go-back-N ARQYour Answer: Selective repeat ARQ True/FalseQuestion: For efficient multicasting, a shortest path spanning tree represents the communication path.Correct Answer: TrueYour Answer: False Multiple Choice Multiple AnswerQuestion: Repeater's features are :-Correct Answer: It operates in physical layer , It forwards every frame , It connects network segment Your Answer: It operates in physical layer , It forwards every frame , It connects network segment
LIST OF ATTEMPTED QUESTIONS AND ANSWERS True/False Question: Data rate of fast Ethernet is 100 Mbps. Correct Answer: True Your Answer: True Multiple Choice Single Answer Question: The identifier used for data transfer is :- Correct Answer: Virtual circuit identifier (VCI) Your Answer: Virtual circuit identifier (VCI) Multiple Choice Single Answer Question: In spanning tree bridge :- Correct Answer: Logical topology is created Your Answer: Physical and logical topology is created Multiple Choice Single Answer Question: Twisted -pair Ethernet is also known as :- Correct Answer: 10BASET Your Answer: 10BASET
Multiple Choice Single Answer Question: Which of the following connects LAN to another of the same type? Correct Answer: A network bridge Your Answer: A network bridge Multiple Choice Multiple Answer Question: The types of Internet Group Management Protocol (IGMP) message are :- Correct Answer: Leave Report , Membership Report , Query Your Answer: Membership Report , Query , Update Multiple Choice Multiple Answer Question: Digital transmission is possible in :- Correct Answer: Serial mode , Parallel mode Your Answer: Serial mode , Parallel mode True/False Question: In a star backbone, the topology of the backbone is star. Correct Answer: True Your Answer: True Multiple Choice Multiple Answer Question: A token passing network :- Correct Answer: Provide access to the network by only one station at a time , Can provide access only to the station which is having token , Can be either ring or bus network Your Answer: Provide access to the network by only one station at a time , Can provide access only to the station which is having token , Can be either ring or bus network Multiple Choice Single Answer Question: Fiber Optic Ethernet is also known as:- Correct Answer: 10BASEF Your Answer: 10BASEF Multiple Choice Single Answer Question: Which organization has developed much of the original standards for LAN? Correct Answer: IEEE Your Answer: IEEE True/False Question: A central computer surrounded by one or more satellite computers is called a bus network. Correct Answer: False Your Answer: False Multiple Choice Multiple Answer Question: In digital data transmission :- Correct Answer: Baud rate is equal to bit rate , Baud rate is always smaller than the bit rate Your Answer: Baud rate is equal to bit rate , Baud rate is always smaller than the bit rate Select The Blank Question: The X.25 standard specifies ________ protocol layers are the serial interface gateway. Correct Answer: 3 Your Answer: 3 Select The Blank Question: In IPv6 only ________ can fragment.
Correct Answer: Original source Your Answer: Original source Multiple Choice Single Answer Question: Peer to peer communication involves:- Correct Answer: Computers to share information over a network Your Answer: Computers to share information over a network Multiple Choice Multiple Answer Question: Modulation is used for :- Correct Answer: Reduce the band width , Reduce the antenna size , Transmit multiple signals Your Answer: Reduce the band width , Transmit multiple signals , Ensure good transmission quality Multiple Choice Single Answer Question: An error detecting code which is the remainder resulting from dividing the bits to be checked by a predetermined binary number, is known as :- Correct Answer: Cyclic Redundancy check Your Answer: Cyclic Redundancy check Multiple Choice Multiple Answer Question: Features of hub are :- Correct Answer: Hub is a broadcasting device , Hub operates at physical layer , Hub transmits signals to other Your Answer: Hub is a broadcasting device , Hub operates at physical layer , Hub transmits signals to other Multiple Choice Single Answer Question: The layer responsible for process-to-process delivery is :- Correct Answer: Transport layer Your Answer: Physical layer Select The Blank Question: In ________ multiple frames can transmit at the same time. If there is an error, retransmission begins with the last acknowledged frame even if subsequent frames have arrived correctly. Correct Answer: Go-back-N ARQ Your Answer: Go-back-N ARQ Select The Blank Question: Most modern versions of Ethernet use ________ as the transmission medium. Correct Answer: UTP Your Answer: UTP Multiple Choice Single Answer Question: Standard or thick wire Ethernet is also known as :- Correct Answer: 10BASE5 Your Answer: 10BASE5 Multiple Choice Single Answer Question: The main standards relating to Ethernet networks are :- Correct Answer: IEEE 802.2 and IEEE 802.3 Your Answer: IEEE 802.2 and IEEE 802.3 Multiple Choice Multiple Answer Question: Data transmission modes are :-
Correct Answer: Simplex , Half duplex , Full duplex Your Answer: Simplex , Half duplex , Full duplex Multiple Choice Single Answer Question: Which of the following connects LAN to a WAN? Correct Answer: A network gateway Your Answer: A network gateway Match The Following Question Correct Answer Your Answer CRC 4 bytes 6 bytes Ethernet address 6 bytes 46 to 1500 bytes Ethernet frame 64 bytes 128 bytes Data field 46 to 1500 bytes 4 bytes Multiple Choice Single Answer Question: In a mesh topology, the relationship between one device and another is Correct Answer: Peer-to-peer Your Answer: Peer-to-peer True/False Question: The physical layer of a network controls error detection and correction. Correct Answer: False Your Answer: True Select The Blank Question: In ATM, ________ is designed to travel sequentially a single message. Correct Answer: AAL5 Your Answer: AAL1 Select The Blank Question: In ATM, ________ is designed to support a data stream of variable data rate. Correct Answer: AAL2 Your Answer: AAL2 Multiple Choice Single Answer Question: The cable connecting a DB - 9 connector at one end to a DB 25 connector at the other end must cross- connect pin 8 at the DB-9 side to which pin at the DB - 25 side? Correct Answer: 5 Your Answer: 5 True/False Question: T1 and T3 carrier lines are suitable for bursty data traffic. Correct Answer: False Your Answer: True Multiple Choice Multiple Answer Question: A repeater :- Correct Answer: Connects segments of a LAN , Forwards every frame , Is a regenerator Your Answer: Connects segments of a LAN , Forwards every frame , Is a regenerator Multiple Choice Single Answer Question: In Switched Virtual Circuit (SVC), the connection between source and destination is set up :- Correct Answer: Temporarily Your Answer: Logically
Multiple Choice Single Answer Question: Which organisation has developed much of the original standards? Correct Answer: IEEE Your Answer: IEEE Multiple Choice Multiple Answer Question: Three sets of protocols are defined for making PPP a powerful protocol :- Correct Answer: Link control protocol (LCP) , Authentication protocol , Network control protocol (NCP) Your Answer: Link control protocol (LCP) , Network control protocol (NCP) , HDLC protocol Multiple Choice Multiple Answer Question: CHAP packets include :- Correct Answer: Challenge , Response , Success and failure Your Answer: Challenge , Response , Success and failure Multiple Choice Single Answer Question: The actual transmission and reception of data on an RS - 232 interface occurs :- Correct Answer: On pins 2 and 3 Your Answer: On pins 2 and 3 Match The Following Question Correct Answer Your Answer 10Base-FL Fiber link Ethernet Fiber link Ethernet 10Base5 Thicknet Thicknet 10Base2 Cheaper net Switched Ethernet 10BaseT Twisted pair ethernet Twisted pair ethernet Multiple Choice Single Answer Question: Codes are always :- Correct Answer: Either 7 or 8 bits per character Your Answer: Predecided between sender and receiver Select The Blank Question: In X.25 network layer protocol, the data contains________. Correct Answer: One octet of header plus data Your Answer: Three octet of header plus data Multiple Choice Single Answer Question: The physical path over which a message travels is :- Correct Answer: Media Your Answer: Media True/False Question: TCP uses negative acknowledgement in communication. Correct Answer: False Your Answer: False Multiple Choice Multiple Answer Question: A remote bridge :- Correct Answer: Useful for several offices with LANs , Acts as point-to-point link , Uses PPP protocol Your Answer: Useful for several offices with LANs , Acts as point-to-point link , Uses PPP protocol
Multiple Choice Multiple Answer Question: HDLC supports :- Correct Answer: Half duplex communication , Full duplex communication , ARQ mechanisms Your Answer: Half duplex communication , Full duplex communication , ARQ mechanisms Select The Blank Question: In 100BaseX ________ bits of data is received from network interface card. Correct Answer: 8 Your Answer: 8
LIST OF ATTEMPTED QUESTIONS AND ANSWERS Multiple Choice Single Answer Question: In Permanent Virtual Circuit (PVC), the connection between source and destination is set up :- Correct Answer: Permanently Your Answer: Permanently Multiple Choice Single Answer Question: Which of the following device is used with an X.25 network to provide service to asynchronous terminals? Correct Answer: Packet assembler/disassembler Your Answer: Gateway Multiple Choice Single Answer Question: In sub networks the number of intermediate levels of hierarchy in IP addressing are :- Correct Answer: Three Your Answer: Three Multiple Choice Single Answer Question: In OSI network architecture, the dialoge control and token management are the responsibilities of :- Correct Answer: Session layer Your Answer: Data link layer Select The Blank Question: The virtual path identifier (VPI) of user to network interface (UNI) is ________ bits in length. Correct Answer: 8 Your Answer: 8 Multiple Choice Single Answer Question: The information to be communicated in a communication system is :- Correct Answer: Message Your Answer: Message True/False Question: Gateway allows devices on one network to communicate with devices on another network. Correct Answer: True Your Answer: True Multiple Choice Multiple Answer Question: Types of Border Gateway Protocol (BGP) messages Correct Answer: Notification , Keep alive , Update
Your Answer: Notification , Keep alive , Update Select The Blank Question: In ________ the sender sends a frame and waits for an acknowledgement from the receiver before sending the next frame. Correct Answer: Stop-and-wait ARQ Your Answer: Stop-and-wait ARQ Multiple Choice Multiple Answer Question: The physical path in ATM is :- Correct Answer: Physical connection between two switches , Connection between an end point and a switch , Used for data transfer Your Answer: Physical connection between two switches , Used to connect switches , Used for data transfer Multiple Choice Single Answer Question: Which organization develop the original RS - 232C specification? Correct Answer: EAI Your Answer: EAI Multiple Choice Single Answer Question: Regulation of the rate of transmission of data frames is known as :- Correct Answer: Flow control Your Answer: Data rate control Multiple Choice Multiple Answer Question: A data terminal serves as :- Correct Answer: Effecter , Sensor Your Answer: Effecter , Transmitter , Modulator Multiple Choice Multiple Answer Question: A spanning tree bridge :- Correct Answer: Has no loops , Creates logical topology , Uses BPDU Your Answer: Creates logical topology , Uses BPDU , Forward every frame Match The Following Question Correct Answer Your Answer Communication system Hardware, software, and data Hardware, software, and data transferal
transferal links links Digital 0 and 1 Asynchronous transmission FDM Band width of the medium Signal to noise ratio Start and stop bits Asynchronous transmission 0 and 1 True/False Question: Frame Relay does not provide flow control or error control, they must be provided by upper layer protocols. Correct Answer: True Your Answer: True True/False Question: A local area network connects distance computers. Correct Answer: False Your Answer: False Select The Blank Question: Flow control ________.
Correct Answer: Prevents overflow at receiver Your Answer: Controls overflow at receiver Select The Blank Question: The ________ Timer is used in termination phase. Correct Answer: Time waited Your Answer: Time waited Select The Blank Question: Transport layer is responsible for delivery of ________ from one node to other. Correct Answer: Message Your Answer: Message Multiple Choice Single Answer Question: MAC is :- Correct Answer: A method of determining which device has access to the transmission medium at any time Your Answer: A method of determining which device has access to the transmission medium at any time True/False Question: Modulation is the process of sending a file from one computer to another computer. Correct Answer: False Your Answer: True True/False Question: The basic data unit in an ATM network is called a cell. Correct Answer: True Your Answer: True True/False Question: The application layer of a network defines the user's port into the network. Correct Answer: False Your Answer: False Select The Blank Question: ATM standard defines ________ layer. Correct Answer: Three Your Answer: Three Multiple Choice Multiple Answer Question: Features that encourages the wide spread use of ATM in telecommunication are :- Correct Answer: High speed data rate , Low error rate , Low operating cost Your Answer: High speed data rate , Low error rate , Low operating cost True/False Question: Data rate of traditional Ethernet is 100Mbps. Correct Answer: False Your Answer: True Multiple Choice Multiple Answer Question: Point-to-point access protocol is :- Correct Answer: Internet protocol , Dedicated Internet protocol , Version of HDLC Your Answer: Internet protocol , Version of HDLC , Password authentication protocol Multiple Choice Multiple Answer
Question: Channelization protocols are :- Correct Answer: TDMA , CDMA , FDMA Your Answer: TDMA , CDMA , FDMA Multiple Choice Multiple Answer Question: In ATM, connection between two end points is accomplished through :- Correct Answer: Transmission paths (TPs) , Virtual Paths (VPs) , Virtual circuits (VCs) Your Answer: Transmission paths (TPs) , Virtual Paths (VPs) , Virtual circuits (VCs) True/False Question: Devices on one network can communicate with device on another network via a gateway. Correct Answer: True Your Answer: True Multiple Choice Multiple Answer Question: IPCP defines three categories of seven packets :- Correct Answer: Configure , Terminate , Code Your Answer: Configure , Code , Challenge Multiple Choice Single Answer Question: The cheapest modems can transmit :- Correct Answer: 300 bits per second Your Answer: 300 bits per second Multiple Choice Multiple Answer Question: The functions of ATM layers are :- Correct Answer: Routing , Switching , Multiplexing Your Answer: Routing , Switching , Bridging Select The Blank Question: Error control is based on ________. Correct Answer: ARQ Your Answer: Frame check sequence Multiple Choice Single Answer Question: CCITT.V series standards relate primarily to which area of data communication ? Correct Answer: Asynchronous communication Your Answer: ISDN Multiple Choice Single Answer Question: A bridge never forwards frames to :- Correct Answer: Blocking port Your Answer: Blocking port Select The Blank Question: In 100BaseT4 ________ is used as transmission media. Correct Answer: Twisted pair cable Your Answer: Fiber optic cable True/False Question: Half-duplex transmission limits communication in one direction at a time. Correct Answer: True Your Answer: True Select The Blank
Question: In a ________ connection, more than two devices can share a single link. Correct Answer: Multipoint Your Answer: Multipoint Multiple Choice Multiple Answer Question: Frame Relay operates in :- Correct Answer: Physical Layer , Data link Layer Your Answer: Physical Layer , Data link Layer , Session Layer Select The Blank Question: The end-to-end delivery of the entire message is the responsibility of the ________ layer. Correct Answer: Network Your Answer: Transport Multiple Choice Multiple Answer Question: The features of TCP are :- Correct Answer: Connection oriented protocol , Reliable protocol , Stream transport layer protocol Your Answer: Connection oriented protocol , Reliable protocol , Stream transport layer protocol Match The Following Question Correct Answer Your Answer Multiplexing FDM FDM Bounded Media Fiber optic cable Simplex Wireless Transmission Microwave Fiber optic cable Highest Attention UTP cable UTP cable Select The Blank Question: For 1000Base-T Gigabit Ethernet ________ line coding is used. Correct Answer: 4D /PAM 5 Your Answer: 8B /6T Multiple Choice Single Answer Question: Each station is assigned a unique code in :- Correct Answer: CDMA Your Answer: TDMA True/False Question: ATM cell size varies according to the size of data. Correct Answer: False Your Answer: True
LIST OF ATTEMPTED QUESTIONS AND ANSWERS Multiple Choice Multiple AnswerQuestion: Point-to-point access protocol is :-Correct Answer: Version of HDLC , Internet protocol , Dedicated Internet protocol Your Answer: Internet protocol , Dedicated Internet protocol , Password authentication protocol Multiple Choice Multiple AnswerQuestion: TCP connection establishment uses :-Correct Answer: Three way handshake , Full duplex mode Your Answer: Two way handshake , Full duplex mode , Half duplex mode
Multiple Choice Single AnswerQuestion: In OSI network architecture, the dialoge control and token management are the responsibilities of :-Correct Answer: Session layerYour Answer: Session layer True/FalseQuestion: Demodulation is the process of converting digital signals to analog signals.Correct Answer: FalseYour Answer: True Multiple Choice Single AnswerQuestion: Twisted -pair Ethernet is also known as :-Correct Answer: 10BASETYour Answer: 10BASET True/FalseQuestion: Frequency-division multiplexer divides the high speed signal into frequency bands.Correct Answer: TrueYour Answer: False Multiple Choice Single AnswerQuestion: The oldest method of multiple access is :-Correct Answer: ALOHAYour Answer: CSMA / CA Multiple Choice Multiple AnswerQuestion: The versions of AAL layers are :-Correct Answer: AAL1 and AAL2 , AAL3/4 and AAL5 Your Answer: AAL3/4 and AAL5 Multiple Choice Multiple AnswerQuestion: In fast Ethernet functions of autonegotiation are :-Correct Answer: To allow incompatible devices to one other , To allow one device to have multiple capability , To allow station to check hub's capability Your Answer: To allow one device to have multiple capability , To allow station to check hub's capability , Management functions Select The BlankQuestion: For delivery the user datagram to the correct application program, UDP needs________.Correct Answer: Port addressYour Answer: Internet address Multiple Choice Single AnswerQuestion: In OSI network architecture, the routing is performed by :-Correct Answer: Network layerYour Answer: Transport layer True/FalseQuestion: A device that can convert digital signals to analog signals is a packet.Correct Answer: FalseYour Answer: False Multiple Choice Single Answer
Question: CCITT. I series standers relate primarily to which area of data communication ?Correct Answer: ISDNYour Answer: Asynchronous communication Select The BlankQuestion: The full abbreviation for AAL is________.Correct Answer: Application Adaptation layerYour Answer: Application Adaptation layer Select The BlankQuestion: IPv6 allows ________ addressing.Correct Answer: ClasslessYour Answer: Classless Select The BlankQuestion: Urgent data require the urgent pointer field as well as the URG bit in the ________ field.Correct Answer: ControlYour Answer: Control Select The BlankQuestion: ________ topology requires a central controller or hub.Correct Answer: StarYour Answer: Star Multiple Choice Single AnswerQuestion: In Permanent Virtual Circuit (PVC), the connection between source and destination is set up :-Correct Answer: PermanentlyYour Answer: Permanently True/FalseQuestion: The data link layer, in reference to the OSI model, specifies the virtual circuit interface to packet-switched service.Correct Answer: FalseYour Answer: True Multiple Choice Multiple AnswerQuestion: In digital data transmission :-Correct Answer: Baud rate is always smaller than the bit rate , Baud rate is equal to bit rate Your Answer: Baud rate is always smaller than the bit rate , Baud rate is equal to bit rate True/FalseQuestion: For multicasting between two non contiguous multicast routers, a multicast backbone (MBONE) is used to enable tunneling.Correct Answer: TrueYour Answer: True Multiple Choice Multiple AnswerQuestion: Criteria for transparent bridge are :-Correct Answer: Frame address change , Forwarding table is automatically learning frame movements , Forward every frame Your Answer: Frame address change , Prevent loops , Forward every frame Multiple Choice Single AnswerQuestion: The wavelength of a signal depends on the :-
Correct Answer: Frequencies of the signalYour Answer: Amplitude Multiple Choice Single AnswerQuestion: The physical path over which a message travels is :-Correct Answer: MediaYour Answer: Media Multiple Choice Single AnswerQuestion: Which organization develop the original RS - 232C specification?Correct Answer: EAIYour Answer: EAI Match The FollowingQuestion Correct Answer Your AnswerServer Remote Host Transport layer addressPort number Transport layer address Transport layer addressSocket Address Combination of IP address and Remote Host
port numberClient Local Host Local Host True/FalseQuestion: Devices on one network can communicate with device on another network via a gateway.Correct Answer: TrueYour Answer: True Multiple Choice Single AnswerQuestion: Fiber Optic Ethernet is also known as:-Correct Answer: 10BASEFYour Answer: 10BASE2 Multiple Choice Single AnswerQuestion: The data unit in user datagram protocol (UDP) is called as :-Correct Answer: DatagramYour Answer: Datagram Multiple Choice Multiple AnswerQuestion: In Switched Virtual Circuit (SVC) :-Correct Answer: Temporary connection is set up , Acknowledgement frames are used Your Answer: Temporary connection is set up Select The BlankQuestion: The ATM data packet is a cell composed of ________ bytes.Correct Answer: 53Your Answer: 64 True/FalseQuestion: The root bridge has largest ID.Correct Answer: FalseYour Answer: True Multiple Choice Multiple AnswerQuestion: A Bridge :-Correct Answer: Operates in physical and data link layer , Has filtering capability , Does not change physical address in the frame
Your Answer: Operates in physical and data link layer , Has filtering capability , Does not change physical address in the frame Multiple Choice Multiple AnswerQuestion: Point-to-point (PPP) provides following services :-Correct Answer: Defining frame format , Defines link establishment , defines authentication process of devices Your Answer: Defines link establishment , defines authentication process of devices , Defines frame check True/FalseQuestion: ATM cell size varies according to the size of data.Correct Answer: FalseYour Answer: True Multiple Choice Single AnswerQuestion: A devices that links two homogeneous packet-broadcast local networks, is :-Correct Answer: BridgeYour Answer: Bridge Multiple Choice Single AnswerQuestion: Which of the following method is used for dedicated communications path between two devices through one or more intermediate switching node?Correct Answer: Circuit switchingYour Answer: Packet switching Multiple Choice Multiple AnswerQuestion: Routers used in OSPF :-Correct Answer: Area border router , Backbone router , Autonomous system boundry router (ASBR) Your Answer: Buffer Router , Area border router , Autonomous system boundry router (ASBR) Select The BlankQuestion: Most modern versions of Ethernet use ________ as the transmission medium.Correct Answer: UTPYour Answer: Coaxial cable Multiple Choice Single AnswerQuestion: A bridge :-Correct Answer: Checks the destination address of a frame and decide whether it should be forwarded or droppedYour Answer: Checks the destination address of a frame and decide whether it should be forwarded or dropped Select The BlankQuestion: In Ethernet LAN ________ is the source address.Correct Answer: UnicastYour Answer: Unicast Match The FollowingQuestion Correct Answer Your AnswerATM Real time transmission WANX.25 data rate 64 Kbps 64 KbpsT-1 carrier data rate 1.54 Mbps Real time transmissionFrame Relay data rate 1.544Mbps 1.544Mbps
Multiple Choice Multiple AnswerQuestion: Modulation is used for :-Correct Answer: Reduce the band width , Reduce the antenna size , Transmit multiple signals Your Answer: Reduce the band width , Transmit multiple signals , Ensure good transmission quality True/FalseQuestion: Border Gateway Protocol (BGP) is an interautonomous routing protocol.Correct Answer: TrueYour Answer: True Select The BlankQuestion: In X.25 network layer protocol, the data contains________.Correct Answer: One octet of header plus dataYour Answer: Four octet of header plus data Multiple Choice Single AnswerQuestion: The number of steps involved in connection establishment phase of TCP are :-Correct Answer: ThreeYour Answer: Three Select The BlankQuestion: The ________ timer keep a track of the time between the sending of segment and the receipt of an acknowledgement.Correct Answer: RetransmissionYour Answer: Retransmission
LIST OF ATTEMPTED QUESTIONS AND ANSWERS Select The BlankQuestion: The ________ field is used for error detection.Correct Answer: ChecksumYour Answer: Checksum Select The BlankQuestion: The TCP and UDP both protocols operate at ________.Correct Answer: Transport layerYour Answer: Transport layer True/FalseQuestion: Half-duplex transmission limits communication in one direction at a time.Correct Answer: TrueYour Answer: True True/FalseQuestion: Data rate of traditional Ethernet is 100Mbps.Correct Answer: FalseYour Answer: False Multiple Choice Single AnswerQuestion: According to the PPP transition state diagram, exchange of user control and data packets occurs in the :-Correct Answer: Networking stateYour Answer: Terminating state
True/FalseQuestion: PHY sub layer is responsible for encoding and decoding.Correct Answer: TrueYour Answer: True True/FalseQuestion: IPv6 is also known as IPng.Correct Answer: TrueYour Answer: False Multiple Choice Multiple AnswerQuestion: The two steps of PAP :-Correct Answer: Authentication identification , Validity of information Your Answer: Validity of information , Manipulating the value and sends the result back Multiple Choice Single AnswerQuestion: In Switched Virtual Circuit (SVC), the connection between source and destination is set up :-Correct Answer: TemporarilyYour Answer: Temporarily Multiple Choice Single AnswerQuestion: Carrier is :-Correct Answer: A continuous frequency capable of being modulated or impressed with a second signalYour Answer: A continuous frequency capable of being modulated or impressed with a second signal Multiple Choice Single AnswerQuestion: The retransmission of damaged or lost frames in the data link layer is known as :-Correct Answer: Error controlYour Answer: Error control Select The BlankQuestion: As frequency increases, the period________.Correct Answer: DecreasesYour Answer: Decreases Multiple Choice Multiple AnswerQuestion: CHAP packets include :-Correct Answer: Challenge , Response , Success and failure Your Answer: Challenge , Success and failure , Configuration Multiple Choice Single AnswerQuestion: Which organization has developed much of the original standards for LAN?Correct Answer: IEEEYour Answer: ISO Multiple Choice Single AnswerQuestion: Multicast backbone (MBONE) is a protocol used for :-Correct Answer: Multimedia and real time communicationYour Answer: Instant communication Multiple Choice Single AnswerQuestion: Two - state(binary) communications systems are better than single state systems because :-
Correct Answer: The components are more reliableYour Answer: The components are more reliable Multiple Choice Multiple AnswerQuestion: Protocol used for authentication in PPP :-Correct Answer: PAP (Password Authentication Protocol) , CHAP (Challenge Handshake Protocol) Your Answer: PAP (Password Authentication Protocol) Multiple Choice Multiple AnswerQuestion: Congestion prevention policies for data link layer areCorrect Answer: Flow control policy , Acknowledgement policy , Retransmission policy Your Answer: Flow control policy , Retransmission policy , Multicasting policy Select The BlankQuestion: In 100 Base TX Ethernet ________ line coding is used.Correct Answer: 4B /5BYour Answer: 4B /5B True/FalseQuestion: Gateway is used for modulation and demodulation.Correct Answer: FalseYour Answer: False Match The FollowingQuestion Correct Answer Your AnswerRouter Limitations of 10 Base T Fast NetworkBridge Uses tables for filtering decisions Broadband domainsRepeater No filtering capacity Limitations of 10 Base THub Increase length No filtering capacity Multiple Choice Single AnswerQuestion: Routing with an autonomous system is referred as :-Correct Answer: Interior routingYour Answer: Interior routing Multiple Choice Single AnswerQuestion: The main functional difference between circuit switched digital networks (CSDN) and packet-switched digital network(PSDN)isCorrect Answer: That a CSDN establishes a permanent connection between two nodes where PSDN uses a virtual circuitYour Answer: That more data can be transmitted Select The BlankQuestion: In ________ multiple frames can be in transit at the same time. If there is an error only the unacknowledged frame is retransmitted.Correct Answer: Selective repeat ARQYour Answer: Stop-and-wait ARQ Multiple Choice Multiple AnswerQuestion: IPv6 address supports :-Correct Answer: Hexadecimal colon notation , CIDR address , Classless address Your Answer: Two-level address , Hexadecimal colon notation , CIDR address Multiple Choice Multiple AnswerQuestion: Types of Border Gateway Protocol (BGP) messages
Correct Answer: Notification , Keep alive , Update Your Answer: Notification , Keep alive , Update Select The BlankQuestion: ATM defines ________ versions of application adaptation Layer(AAL).Correct Answer: FourYour Answer: Four Multiple Choice Multiple AnswerQuestion: Bit Stuffing is :-Correct Answer: Adding one extra ' 0' , Stuffing at sender , Removing at sender Your Answer: Adding one extra ' 0' , Stuffing at sender , Adding one extra '1' Multiple Choice Multiple AnswerQuestion: The functions of ATM layers are :-Correct Answer: Routing , Switching , Multiplexing Your Answer: Routing , Switching , Multiplexing Select The BlankQuestion: The full abbreviation for AAL is________.Correct Answer: Application Adaptation layerYour Answer: Administrative Application Layer True/FalseQuestion: A medium access control technique for multiple access transmission media is amplitude.Correct Answer: FalseYour Answer: True Multiple Choice Multiple AnswerQuestion: Link control protocol (LCP) is responsible for :-Correct Answer: Establishing , Maintaining , Configuring Your Answer: Maintaining , Configuring , Controlling state True/FalseQuestion: A repeater connects two LANs of different protocols.Correct Answer: FalseYour Answer: True Multiple Choice Multiple AnswerQuestion: OSPF features are :-Correct Answer: Multiple circuit load balancing , Converge very quickly to network topology change , Not susceptible to routing loops Your Answer: Converge very quickly to network topology change , Not susceptible to routing loops , Fixed length subnetting Multiple Choice Single AnswerQuestion: A router determines the best path for a packet by consulting :-Correct Answer: Routing tableYour Answer: Network node Select The BlankQuestion: Flow control ________.Correct Answer: Prevents overflow at receiverYour Answer: Controls overflow at transmitter
True/FalseQuestion: A bridge should be able to connect different LAN protocols.Correct Answer: TrueYour Answer: False Match The FollowingQuestion Correct Answer Your AnswerProcess-to-process Transport layer Network layerIPv6 Classless Addressing Classful AddressingNode-to-node delivery Data link layer Data link layerHost-to-host delivery Network layer Transport layer Multiple Choice Single AnswerQuestion: Producer to handle collision is :-Correct Answer: CSMA / CDYour Answer: CSMA / CD True/FalseQuestion: Repeater operates in physical layer.Correct Answer: TrueYour Answer: True True/FalseQuestion: The 5-7 digits are known as the country code of the Network User Address (NUA)Correct Answer: FalseYour Answer: True Multiple Choice Single AnswerQuestion: All of the parts in a computer talk to each other by sending :-Correct Answer: Digital signalsYour Answer: Digital and Analog Select The BlankQuestion: In fast Ethernet autonegotiation allows ________ negotiation.Correct Answer: Data rateYour Answer: BW Multiple Choice Single AnswerQuestion: CCITT.V series standards relate primarily to which area of data communication ?Correct Answer: Asynchronous communicationYour Answer: Wide area network Multiple Choice Multiple AnswerQuestion: The X.25 standard :-Correct Answer: Covers three OSI layers , Specifies a data bit rate , Specifies a DTE/DCE interface Your Answer: Specifies a data bit rate , Specifies a DTE/DCE interface Multiple Choice Single AnswerQuestion: In Permanent Virtual Circuit (PVC), the connection between source and destination is set up :-Correct Answer: PermanentlyYour Answer: Permanently Multiple Choice Multiple AnswerQuestion: Transition states of PPP are :-