CMP-1: CEILING MOUNT PARTS CMP-1 Column Assembly Manual

CMP-1 Column Assembly

Manual

CMP-1: CEILING MOUNT PARTS

Adjustable Fixed

Fully read and complete the instructions in this manual prior to assembling the Ceiling Tilt Mount.

All Rights Reserved. 2014 SkyVue®

3InstallatIon ManualCMP-1 Parts / ColuMn asseMbly |

Table of ConTenTs

Common Ceiling mount Parts

adjustable Ceiling Column Parts

adjustable Column digram

assembling adjustable Column

Fixed Ceiling Column Parts

Fixed Column diagram

assembling Fixed Column

oPtional swivel adaPter diagram

5

678

121314

17

4 All Rights Reserved. 2014 SkyVue®


2 qty. Ceiling/Mounting Star Plate

Common Ceiling Mount Parts:These parts are found in the supplied Ceiling Mount Parts (CMP-1) box

1 qty. Elbow Assembly

1 qty. Coupler

1 qty. Security Allen Wrench

2 qty. - Set Screw

2 qty. Security Set Screw

4 qty. 5/16” Hex Head Bolts

12 qty. Flat Washers

4 qty. NyLock Nuts

4 qty. 5/16” Lag Bolts

Tools Required for Installation:

Ratchet with 1/2” Socket Drill with 3/16” Wood Bit

1/2”


Parts & Column Assembly

Adjustable Ceiling Column Parts:These parts can be found in the tube labeled “Adjustable Column”

Fixed Length Column

The length of this column will vary depending on your specific order.

5/16” Stainless Steel Bolt

5/16” Stainless Steel Flat Washer

5/16” Stainless Steel Lock Washer

5/16” x 1/4” Set Screw

5/16” x 1/4” Security - Set Screw

3/16” Allen Wrench

Outer Tube Column


Adjustable Column Digram:

Security - Set Screw




(Opposite Side) 2 qty.

Security Set Screws

Bolt

Lock Washer

Flat WasherAdjustable Column

Coupler

Elbow Assembly

Ceiling Star Plate

Mounting Star Plate



Assembling Adjustable Column:

• Thread elbow assembly to mounting star plate, paying special attention not to cross thread the parts.

• Hand tighten set screw.

Security set screws will get fully secured after final adjustments have been made.

• Thread coupler to elbow assembly, paying special attention not to cross thread the parts.


Security set screw will get fully secured after final adjustments have been made.

If you have purchased the optional swivel adapter, please refer to the last page for reference diagram before proceeding with installation.



Coupler


• Carefully thread outer tube column to coupler, paying special attention not to cross thread the parts.



• Find a cross beam in ceiling.

• Use the Ceiling star plate as a template to mark drill locations.

• With wood bit, drill 3/16” pilot hole.

• Place a flat washer on the supplied lag bolts and with a 1/2” ratchet secure the ceiling star plate to the ceiling.


Warning: Ceiling star plate must be fastened to a cross beam or other structurally sound support within the ceiling. Not doing so can result in mount failure.

3/8”

4”

2”

5”

5”4”

2”

1-1/2” NPS



• Thread fixed length column into star ceiling plate, paying special attention not to cross thread the parts.

• Tighten set screw using the provided allen wrench.

Take notice that the cable access hole is on the top of the column near the ceiling.

• Insert outer tube column on to the fixed length column.

• Place a lock washer and flat washer onto the 5/16” bolt in the order shown.

• Select height setting ( )

• Tighten bolt with supplied allen wrench

• Insert and hand tighten set screw on coupler

• On the opposite side - insert and tighten 2 set screws.

2 Set Screws (Located on Opposite Side)


Remember to tighten all set screws upon making final adjustments.

1

2

3



Proceed to the box labeled:

CMTM to complete your installation



Fixed Ceiling Column Parts:These parts can be found in the tube labeled “Fixed Column”

Fixed Length Column

The length of this column will vary depending on your specific order.


Fixed Column Diagram:





Fixed Column

Coupler

Elbow Assembly

Ceiling Star Plate

Mounting Star Plate



Assembling Fixed Column:

• Thread elbow assembly to mounting star plate, paying special attention not to cross thread the parts.


Security set screws will get fully secured after final adjustments have been made.

• Thread coupler to elbow assembly, paying special attention not to cross thread the parts.






Coupler


• Thread the fixed length column into the lower assembly, paying special attention not to cross thread the parts.


Take notice that the cable access hole is on the top of the column near the ceiling. Security set screw will get fully secured after final adjustments have been made.


• Find a cross beam in ceiling.

• Use the Ceiling star plate as a template to mark drill locations.

• With wood bit, drill 3/16” pilot hole.

• Place a flat washer on the supplied lag bolts and with a 1/2” ratchet secure the ceiling star plate to the ceiling.

Warning: Ceiling star plate must be fastened to a cross beam or other structurally sound support within the ceiling. Not doing so can result in mount failure.

3/8”

4”

2”

5”

5”4”

2”

1-1/2” NPS

Cable Access Holes



• Thread fixed length column into star ceiling plate, paying special attention not to cross thread the parts.

• Tighten all set screws using the provided allen wrench.





Proceed to the box labeled:

CMTM to complete your installation


The optional swivel adapter gets placed above the coupler in both the adjustable and fixed ceiling mount assemblies.

Optional Swivel Adapter Diagram

Factor in an additional 5.125” to ceiling mount clearance when choosing to use the HD Swivel Adapter.

3”

5.12

5”

Ceili

ngTV

Stop Set Screw

4”

4”2”

2”

All Rights Reserved. 2014 SkyVue®

Notes:

CMP-1: CEILING MOUNT PARTS CMP-1 Column Assembly Manual

Documents